SUPERFRONT bar 20 User manual

Brand
SUPERFRONT
Model
bar 20
Type
User manual
Content
NOTE! Before you start drilling,
always double-check that you have
measured correctly.
Triple-check by holding your handle
at your drill markings and compare
so that you are completely sure that
the drill holes end up at the right
distance from each other and from
the edges.
The distance from the center of the
screw hole to the end of the Bar handle
is 61mm.
I.e. for a Bar 60 which is 597mm, there
should be 477mm between the holes.
(597-61-61=477mm)
If your Bar is longer than 90cm, it has 3
blocks / screws. The middle one is then
placed in the middle between the two
outer ones.
TIP! Drill the hole from the outside of
the front. Hold a piece of wood
tightly against the back of the front,
for the drill to continue into. This will
prevent the front from chipping on
the back where the drill comes out.
Drill diameter 4-5mm.
Superfront /+46868441814 / info@superfront.com / www.superfront.com
Bar 20 — Bar 80 = 2 blocks/screws/SuperWasher. Bar 100 — Bar 236 = 3 blocks/screws/SuperWasher.
2-3 x Mounting screw M4 x 45 mm
2-3 x SuperWasher
Mounting instructions BAR
NOTE!
These instructions are for mounting the Bar handle on fronts
that are exactly as high or wide as the Bar itself.
On door fronts (le or right hung), the Bar must always be
mounted vertically, since a horizontally mounted Bar would hit
the adjacent front or side panel when the door is opened.
A horizontal Bar can only be used on a le or right hung door if
the Bar handle is shorter than the width of the door.
1 x Bar
2-3 x Block
2-3 x Thread
Superfront /+46868441814 / info@superfront.com / www.superfront.com
FRONT’S TOP
BLOCK
BAR
FRONT’S SIDE
61mm
36 mm
VERTICAL GROOVE
Horizontal mounting on a
plain drawer or dishwasher
front:
This placement is for mounting a
Bar that is exactly as long as the
front is wide. The block can be
placed both horizontally and
vertically.
The distance 61mm must be
followed, but the distance 36mm
can be adjusted to taste.
Horizontal mounting on a
drawer or dishwasher front
with Vertical grooves:
The block is placed vertically to
fit between the vertical grooves
of the front.
Mounting instructions BAR
FRONT’S TOP
FRONT’S SIDE
BLOCK
BAR
36 mm
61mm
Superfront /+46868441814 / info@superfront.com / www.superfront.com
FRONT’S TOP
BLOCK
BAR
FRONT’S SIDE
Vertical mounting on a plain door:
This placement is for mounting a Bar that is exactly as long
as the front is high. The block can be placed both horizontally
and vertically. The distance 61mm must be followed but the
distance 36mm can be adjusted to taste.
61mm
36 mm
FRONT’S TOP
BLOCK
BAR
FRONT’S SIDE
Vertical mounting on a door
with Vertical grooves:
The block is placed vertically to fit between the
vertical grooves of the front.
61mm
36 mm
VERTICAL GROOVE
Mounting instructions BAR
METOD BESTÅ PAX
20 30 40
197
61 61
CC 75
297
61 61
CC 175
397
61 61
CC 275
38
381
61 61
CC 259
64
637
61 61
CC 515
128
1277
61 61
CC 577,5
CC 577,5
192
1914
61 61
CC 896
CC 896
201
1990
61 61
CC 934
CC 934
201
2342
61 61
CC 1110
CC 1110
60
597
61 61
CC 475
80
797
61 61
CC 675
100
997
61 61
CC 437,5
CC 437,5
120
1197
61 61
CC 537,5
CC 537,5
140
1397
61 61
CC 637,5
CC 637,5
160
1597
61 61
CC 737,5
CC 737,5
180
1797
61 61
CC 837,5
CC 837,5
200
1997
61 61
CC 937,5
CC 937,5
45
447
61 61
CC 325
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

SUPERFRONT bar 20 User manual

Brand
SUPERFRONT
Model
bar 20
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents