Sytech SYXTR62BT Owner's manual

Category
Portable speakers
Type
Owner's manual
SY·XTR62BT
PORTABLE SPEAKER
USER
MANUAL
Welcome
Thank you for purchasing the new Wireless professional acoustic Party system “XtremeBass” SY-XTR62BT. Please read
this manual carefully before operating your product. And pay close attention to the precautions which are mentioned
below. Store this user manual in a safe place for future reference.
Safety Precautions
Points to observe for safe usage
Read this manual carefully before using the product. They contain instructions on how
to use this product in a safe and effective manner. SYTECH will not be responsible
for problems resulting from failure to observe the instructions in this manual.
Turn off the device immediately in case of a problem.
Failure may cause personal injury or damage to the product.
Return it to your authorized SYTECH dealer for repairing.
Product cleaning.
Use a soft dry cloth for periodic cleaning of the product. For more severe stains, please
dampen the cloth with water only. Any other product such as alcohol, benzene, may damage the paint or
the plastic.
Temperature
Make sure before using the product, the room temperature is between +35ºC (+95ºF) and -10ºC (+14ºF)
Maintenance.
If you have problems, do not attempt to repair the unit yourself.
Surface
Place the unit on a flat surface.
Leave enough space around the unit for a proper ventilation.
Heat.
Do not place the product near any heat sources or to direct sunlight.
Accessories.
Use only supplied accessories
Remote Control Functions
1. Standby
2. Play / Pause. FM Auto scan
3. Decrease volume
4. Equalizer effects
5. Repeat functions
6. Numerical keys
7. Input selection (AUX-USB-TF-FM-BT)
8. Mute
9. Previous track, Previous FM frequency
10. Next track, Next FM frequency
11. Increase volume
12. USB-Micro-SD function
This picture is for reference purposes only”
1. Under normal circumstances, the remote control should be aimed directly at the infrared receiver window of the
unit.
The maximum distance for the remote-control operation is approximately 6 meters and within a 30° angle.
2. When operating the remote control, aim the remote control at the infrared receiver window of the unit and
ensure that there are no obstacles between the remote control and the unit.
3. If the remote receiver is facing direct sunlight, it may fail. In this case, move the speaker away to avoid the light.
4. Avoid mixing old and new batteries. Replace the remote-control batteries regularly.
Wired microphone usage
Simply connect the microphone jack as shown on the diagram to
the jack input located at the rear of the speaker.
Functions and connections
1. LCD Display
2. Recording Function from MIC.
3. Input selection (AUX-USB-TF-FM-BT)
4. Microphone priority function
5. Previous track, Previous FM frequency, Volume decrease
6. Play / Pause, FM Auto scan, TWS
7. Next track, Next FM frequency, Volume increase
1
. Power switch – LED on/off
2. DC 12V. Input
3. AC input
4. USB – Micro-SD slot.
5. Microphone input
6. Aux input
7. Master volume controller
8. Bass controller
9. Treble controller
10. Echo controller
11. Microphone volume controller
12. LED charging indicator (Charging: Red / Completed:
Green)
USB & Micro-SD Slot
USB FUNCTION
Make sure your USB flash is formatted as FAT32.
Insert the USB flash into the USB port of the speaker system
The unit should detect the USB automatically and play the first track
If in the case the USB does not start automatic playback, press the Input button and select MP3 mode.
If you wish to pause the music, simply press the pause button
To select the next track, simply press the “Next” button
To select the previous track, simply press the “Previous” button
Note:
1. Make sure the music files are MP3, WMA format or else the music system will not be able to read the files.
2. Make sure the music files are recorded to the root directory.
3. It is advisable to remove unnecessary files for faster reading of the content.
MICRO-SD CARD FUNCTION
Make sure your Micro-SD card is formatted as FAT32.
Insert the Micro-SD card into the TF slot of the speaker system
The unit should detect the Micro-SD card automatically and play the first track
If in the case the Micro-SD card does not start automatic playback, press the Input button and select MP3 mode.
If you wish to pause the music, simply press the pause button
To select the next track, simply press the “Next” button
To select the previous track, simply press the “Previous” button
Bluetooth function
Select the BLUETOOTH mode using the “MODE” switch on the top panel of the unit or from the remote control itself.
Please ensure the Bluetooth device you wish to connect has the Bluetooth function enabled and visible.
Start the scan function from your device and search for “SY-XTR62BT”.
Once you have found the device, press on it and connect the speaker with the device.
When the connection is successful, a “tick” tone will be heard. If the speaker cannot be connected, please restart the
speaker or the device and try again.
After the connection is successfully established, you can begin to play music. To ensure continuous stability of the
music signal, try to keep the Bluetooth device and the mobile phone facing one another.
The distance for the Bluetooth signal range is up to 14 meters when no obstacles in between.
Mic Recording function
Insert a USB or a Micro-SD card making sure it has enough space to record.
Press the “REC” button to start recording your voice.
Once finished recording press “REC” button once more to save the recording and playback.
FM Radio function
Press the “MODE” button to switch to FM mode.
Press the “Pause/Play” button to start the automatic search of the stations.
The unit will start to search all the main stations and will store them automatically.
Once the scan search has finalized, press the “NEXT” or “PREVIOUS” buttons to access to the stored channels.
The unit will store up to 32 presets.
Note: The FM stations can only be stored automatically. The position of the channel store number will start from the
lowest FM frequency to the highest. The pre-set memories cannot be memorized manually.
TWS Function
The TWS function allows you to connect two speakers at the same time and lets you enjoy “True Wireless
Stereo” music.
There are two ways of connecting the TWS function:
Method 1:
Select any of the two units and connect it to your mobile device via Bluetooth.
Turn on the second unit and enter Bluetooth mode by pressing the “Mode” button.
Long press the “Play-Pause - TWS” button on the two units.
The LED display will show “btst” and the two units will pair to each other automatically.
A beep sound will be heard confirming the pairing of the two speakers and one of the speaker LCD display will show
“bt”.
Play the track from your mobile device and enjoy True Wireless Stereo experience as each speaker will act as left
and right.
To exit the TWS mode, simply long press the “Play-Pause – TWS” button.
Method 2:
Select the Bluetooth mode on the two speakers.
Long press the “Play-Pause - TWS” button on the two units.
The LED display will show “btst” and the two units will pair to each other automatically.
A beep sound will be heard confirming the pairing of the two speakers and one of the speaker LCD display will show
“bt”.
Connect your mobile device via Bluetooth to the speaker.
Play the track from your mobile device and enjoy True Wireless Stereo experience as each speaker will act as left
and right.
To exit the TWS mode, simply long press the “Play-Pause – TWS” button.
Main technical specifications
Basic Specifications
2 x 12” Woofer
USB/Micro-SD/FM/Bluetooth function
1 x Microphone input
1 x Aux input
Recording Function from MIC
LED display
Remote control
RGB light on woofer grill
Output power: 40W RMS.
Output power: 300W PMPO
TWS Function (True Wireless Stereo)
Built
in rechargeable battery 4500 mAh - 12V
Bluetooth Specifications
Bluetooth Module: 115952
Bluetooth Version: V5.0 + EDR
Bluetooth Support: 5.0
Bluetooth Profiles: A2DP, AVRCP
Bluetooth pairing name: SY-XTR62BT
USB/Micro-SD card Specifications
2.0 USB Port (Max Capacity: 32GB)
Micro-SD Card Slot (Max Capacity: 32GB)
Compatible Audio Formats in USB: MP3 / WMA /
WAV
Compatible Audio Formats in SD: MP3 / WMA / WAV
Technical Specifications
Output power: 300W PMPO
Output power: 40W RMS
SNR: 93dB±3dB
Frequency response: 100-18KHz
Power supply: AC110V-240V, 50/60Hz
Driver unit: 2 x 12" woofer
Working time: 3-5 hours (Depends on Volume level)
Charging time: 4 hours
Above specifications are of “SY-XTR62BT are for reference purpose only.
Due to continuous product development, specifications may be subject to change without prior notification.
Do not expose to adverse weather conditions (Such as rain or high temperatures) as it can cause malfunctions
Simple troubleshooting
Try the troubleshooting steps below if you are having problems while using your speaker. If problems still exist, please
look for a qualified technician or contact Sytech technical department.
To prevent electric shock or damage the speaker, do not repair by yourself.
Symptom Possible problem Solution
No function light & no
sound
1. Plug is not well connected
Insert the plug into electrical outlet
2. Speaker power button is
not turned on
Turn on the button
Function light on but no
sound
1. Cable misconnected Turn off the power, check the input jack to ensure
proper audio signal is connected to relevant input jack
2.Speaker are not connected
or misconnected
Power off, then check and confirm the cable
connection again
3.Audio signal is not
transmitted to speaker
Check all the speaker if there is audio signal output
Remote control does not
work
1. Before you press any function button, first select the correct source with the
remote control instead of the main unit
2. Reduce the distance between the remote control and the unit
3. Insert the battery with its polarities (+/- signs) aligned as indicated
4. Replace the battery
5. Aim the remote control directly at the sensor on the front of the unit
Cannot display some files
in the USB device
1. The number of folders or files in the USB device exceeds the max limit. This is not
a malfunction of the unit.
2. The formats of these files are not supported
USB device not supported 1. The USB device is incompatible with the unit. Try another one.
Poor radio reception 1. Increase the distance between the unit and your TV or VCR
2. Fully extend the FM antenna
Bluetooth does not connect
with external device
1. Verify that the external device is compatible with A2DP
2. Verify that the external device is within the transmission range
3. Verify that the external device has already been paired with the unit.
4. Verify if there is no other external device paired with the unit.
If the problem exists after checking related procedures above, please refer to the appointed a service agent to fix
the problem. Do not attempt to open the cover, otherwise the warranty will be void.
Declaration of Conformity
Manufacturer Name: Satyatrade S. L.
Address: Pol.Ind.La Raya. C/ Guadalquivir, 2.
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 91 8864285
NIF: B83254763
Manufacturing country: China
Description: Acoustic Speaker System
Sytech® SY-XTR62BT complies with the following directives:
RED Standard: Directive 2014/53/EU
ROHS Standard: Directive 2011/65/EU Restriction of Hazardous Substances
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator
www.sytech.es
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Sytech SYXTR62BT Owner's manual

Category
Portable speakers
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI