Wacker Neuson HSH650 User manual

Type
User manual

This manual is also suitable for

5000188325 06 1212
5000188325
Operator’s Manual
Hydronic Surface Heater
HSH 650G
HSH 700G
EN
Copyright
notice
© Copyright 2012 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the machine. Any
other type of reproduction is prohibited without express written permission from
Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker Neuson Production
Americas LLC represents an infringement of valid copyrights. Violators will be
prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original
instructions
This Operator’s Manual presents the original instructions. The original language of this
Operator’s Manual is American English.
HSH 650G / HSH 700G Foreword
wc_tx001600gb.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
identification
A nameplate listing the model number, item number, revision number, and serial
number is attached to this machine. The location of the nameplate is shown above.
Serial number
(S/N)
For future reference, record the serial number in the space provided below. You will
need the serial number when requesting parts or service for this machine.
Machine
documentation
î‚„ From this point forward in this documentation, Wacker Neuson Production
Americas LLC will be referred to as Wacker Neuson.
 Keep a copy of the Operator’s Manual with the machine at all times.
î‚„ Use the separate Parts Book supplied with the machine to order replacement
parts.
î‚„ If you are missing either of these documents, please contact Wacker Neuson to
order a replacement or visit www.wackerneuson.com.
î‚„ When ordering parts or requesting service information, be prepared to provide
the machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
î‚„ This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
reduce the risk of injury, carefully read, understand, and observe all instructions
described in this manual.
Machine Item Number Revision
HSH 700G 0620243 2
11 and above
HSH 650G 0620991 106 and above
wc_gr010023
172776
Rev.
Type/Model
Item Number
MADE IN
USA
Manuf.
Yr
Serial Number
Serial Number:
Foreword HSH 650G / HSH 700G
4 wc_tx001600gb.fm
î‚„ Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
machines.
î‚„ The information contained in this manual is based on machines manufactured
up until the time of publication. Wacker Neuson reserves the right to change
any portion of this information without notice.
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and
modifications. The following definitions apply:
î‚„ Approved parts or attachments are those either manufactured or provided by
Wacker Neuson.
î‚„ Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neuson.
î‚„ Unapproved parts, attachments, and modifications are those that do not
meet the approved criteria.
Unapproved parts, attachments, or modifications may have the following
consequences:
î‚„ Serious injury hazards to the operator and persons in the work area
î‚„ Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions about
approved or unapproved parts, attachments, or modifications.
2012_CE_HSH700G_HSH650G_2en.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin 53051 USA
Product
Product
Product category
Product function
Item number
HSH 650, HSH 700
Heating Equipment
To heat surfaces
5000620991, 5000620243
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2006/42/EC, EN 60204-1: 2006, ISO 12100-1: 2003, ISO 12100-2: 2003,
2006/95/EC
Authorized Person for Technical Documents
Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41, 80809 München
Menomonee Falls, WI, USA, 17.09.12
Ed Jaroszewicz
Managing Director
John Lane
Project Engineer
Ed Jaroszewicz
Director of Business Development
Original Declaration of Conformity
Table of Contents
HSH 650 / HSH 700
wc_bo5000188325_06TOC.fm
7
Foreword 3
EC Declaration of Conformity 5
1 Safety Information 11
1.1 Signal Words Used in this Manual ..................................................... 11
1.2 Machine Description and Intended Use ............................................. 12
1.3 Safety Guidelines for Operating the Machine ..................................... 13
1.4 Service Safety .................................................................................... 15
1.5 Safety Guidelines for Lifting the Machine ........................................... 16
1.6 Safety Guidelines for Operating Combustion Burners ....................... 17
1.7 Safety Guidelines for Operating Gensets ........................................... 18
1.8 Safety Guidelines for Towing the Machine ......................................... 20
2 Labels 22
2.1 Label Locations .................................................................................. 22
2.2 Label Meanings .................................................................................. 24
3 Lifting and Transporting 29
3.1 Lifting the Machine ............................................................................. 29
3.2 Preparing the Machine for Transport on a Truck or Trailer ................ 30
3.3 Before Towing Checklist ..................................................................... 31
4 Operation 33
4.1 Control / Component Locations .......................................................... 33
4.2 Control / Component Descriptions ..................................................... 34
4.3 Control Panel ...................................................................................... 35
4.4 Control Panel Components ................................................................ 36
4.5 Pumps, Gauges, and Valves .............................................................. 37
4.6 Genset Control Panel ......................................................................... 38
4.7 Preparing the Machine for First Use ................................................... 39
4.8 Breaking in the Genset ....................................................................... 39
4.9 General Sequence of Operation ......................................................... 40
4.10 Recommended Fuel ........................................................................... 41
4.11 Using the Anti-Theft Fuel Cap ............................................................ 42
4.12 Positioning the Machine ..................................................................... 43
4.13 Pre-Starting Checks ........................................................................... 45
Table of Contents
HSH 650 / HSH 700
wc_bo5000188325_06TOC.fm
8
4.14 Connecting Power to the Machine ......................................................47
4.15 Starting and Stopping the Generator ...................................................48
4.16 Preheating the HTF and Initiating Flow of the HTF .............................49
4.17 Setting the Operating Temperature .....................................................52
4.18 Positioning the Hoses and Operating the Machine .............................53
4.19 Monitoring the Operating Parameters .................................................55
4.20 Stopping the Machine Temporarily ......................................................56
4.21 Emergency Shutdown Procedure ........................................................57
4.22 Rewinding the Hoses ..........................................................................58
4.23 Shutting Down and Packing Up the Machine ......................................60
4.24 Resetting a Low HTF Level Fault ........................................................61
4.25 Resetting the Burner Control ...............................................................63
4.26 Quick-Connect Coupling Usage and Care ..........................................64
4.27 Resetting the Snap Switch ..................................................................65
5 Accessories 66
5.1 Available Accessories .........................................................................66
5.2 Connecting the HX 200 or HX 60 Heat Exchanger .............................67
5.3 Connecting the HX 100 or HX 30 Heat Exchanger .............................69
5.4 Connecting the HX 50 or HX 15 Heat Exchanger ...............................71
5.5 Combining the Machine with One HHS and One DPP ........................73
6 Burner Setup 75
6.1 Factory Settings ..................................................................................75
6.2 Setting up the Burner ..........................................................................75
6.3 Removing and Installing the Burner ....................................................78
6.4 Adjusting the Burner Electrodes ..........................................................80
6.5 Replacing the Burner Nozzle ...............................................................81
6.6 Adjusting the Head ..............................................................................82
6.7 Adjusting the Fuel Pressure ................................................................83
6.8 Adjusting the Air Damper ....................................................................84
7 Maintenance 86
7.1 Periodic Maintenance Schedule ..........................................................86
7.2 Repairing a Hose .................................................................................87
7.3 Inspecting the HTF System and the Fuel System ...............................89
7.4 Inspecting Electrical Cords ..................................................................90
7.5 Filling the HTF Reservoir .....................................................................91
7.6 Cleaning the HTF Strainer ...................................................................93
Table of Contents
HSH 650 / HSH 700
wc_bo5000188325_06TOC.fm
9
7.7 Replacing the Fuel Filter .................................................................... 95
7.8 Lubricating the Hose Reel System ..................................................... 96
7.9 Changing a Turbulator and Cleaning a Turbulator Tube .................... 97
7.10 Inspecting/Replacing the Rope Gasket .............................................. 99
7.11 Storing the Machine ......................................................................... 100
7.12 Storing the Genset ........................................................................... 101
7.13 Preparing the Machine for Seasonal Operation ............................... 102
7.14 Additional HTF Information ............................................................... 103
7.15 Connecting and Maintaining the Battery .......................................... 104
8 Genset Maintenance 105
8.1 Periodic Maintenance Schedule ....................................................... 105
8.2 Checking the Engine Oil ................................................................... 106
8.3 Changing the Engine Oil and Oil Filter ............................................. 107
8.4 Checking the Engine Coolant Level ................................................. 109
8.5 Replacing the Air Filter Element ....................................................... 110
8.6 Replacing Engine Fuel Filter ............................................................ 111
8.7 Changing Engine Coolant ................................................................ 113
8.8 Genset Shut-Down Codes ................................................................ 115
9 Troubleshooting 119
9.1 Troubleshooting the Machine ........................................................... 119
10 Technical Data 121
10.1 Machine ............................................................................................ 121
10.2 Trailer ............................................................................................... 122
10.3 Sound Measurements ...................................................................... 122
10.4 Dimensions ....................................................................................... 123
MSDS: Dowfrost HD 50 124
MSDS: Dowcalâ„¢ 20-G 131
Omron E5CN Temperature Controller 140
11 Schematics 142
11.1 Electrical Schematic - Sheet 1 ......................................................... 142
11.2 Electrical Schematic - Sheet 2 ......................................................... 143
Table of Contents
HSH 650 / HSH 700
wc_bo5000188325_06TOC.fm
10
11.3 Electrical Schematic Components .....................................................144
11.4 Trailer Wiring .....................................................................................149
wc_si000525gb.fm
11
HSH 650G / HSH 700G Safety Information
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE
signal words which must be followed to reduce the possibility of personal injury,
damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a situation
which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
f Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
f To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
f To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
f To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
wc_si000525gb.fm
12
Safety Information HSH 650G / HSH 700G
1.2 Machine Description and Intended Use
This machine is a hydronic surface heater. The Wacker Neuson Hydronic Surface
Heaters consist of trailer-mounted enclosures that house an optional diesel
generator, a hydronic heater, electric motors, fixed pump(s) and plumbing, a diesel
(or gas) burner, a fuel tank, and a hose handling system.
The hydronic heating system utilizes a burner that indirectly warms the Heat
Transfer Fluid (HTF). The warmed HTF is continuously circulated through a
vented, closed loop hose system. A positive displacement pump pushes the
warmed HTF through the hose system, thereby radiating and transferring the heat
to the required application area.
An insulated blanket may be laid over the hoses to increase efficiency. The low
HTF level protection device shuts down the machine if the HTF level drops below
minimum operational capacity.
This machine is intended to be used as a surface heater in order to thaw frozen
ground, to cure concrete, or to prevent frost and freezing. In addition, when used
with other Wacker Neuson accessories, this machine can be used to heat air.
This machine has been designed and built strictly for the intended use(s) described
above. Using the machine for any other purpose could permanently damage the
machine or seriously injure the operator or other persons in the area. Machine
damage caused by misuse is not covered under warranty.
The following are some examples of misuse:
î‚„ Using the machine to heat anything other than what is stated above
î‚„ Using the machine to pump anything other than the factory recommended Heat
Transfer Fluid
î‚„ Using the generator (if equipped) to power anything other than the machine
itself or Wacker Neuson accessory machines, as instructed in the Operator's
Manual
î‚„ Using the machine as a ladder, support, or work surface
î‚„ Using the machine to carry or transport passengers or equipment
î‚„ Using the machine to tow other machines
î‚„ Operating the generator (if equipped) in a manner that is inconsistent with all
federal, state, and local codes and regulations
î‚„ Operating the machine outside of factory specifications
î‚„ Operating the machine in a manner inconsistent with all warnings found on the
machine and in the Operator’s Manual
This machine has been designed and built in accordance with the latest global
safety standards. It has been carefully engineered to eliminate hazards as far as
practicable and to increase operator safety through protective guards and labeling.
However, some risks may remain even after protective measures have been taken.
They are called residual risks. On this machine, they may include exposure to:
î‚„ Heat, noise, and exhaust from the engine or hydronic heater
î‚„ Burns from the HTF or radiant heat from the hoses
wc_si000525gb.fm
13
HSH 650G / HSH 700G Safety Information
î‚„ Fire hazards from improper refueling techniques
î‚„ Fuel and its fumes
î‚„ Personal injury from improper lifting of the trailer tongue
î‚„ Tripping hazards from the hoses
To protect yourself and others, make sure you thoroughly read and understand the
safety information presented in this manual before operating the machine.
1.3 Safety Guidelines for Operating the Machine
Operator
training
Before operating the machine:
î‚„ Read and understand the operating instructions contained in all manuals
delivered with the machine.
î‚„ Familiarize yourself with the location and proper use of all controls and safety
devices.
î‚„ Contact Wacker Neuson for additional training if necessary.
When operating this machine:
î‚„ Do not allow improperly trained people to operate the machine. People
operating the machine must be familiar with the potential risks and hazards
associated with it.
Operator
qualifications
Only trained personnel are permitted to start, operate, and shut down the machine.
They also must meet the following qualifications:
î‚„ have received instruction on how to properly use the machine
î‚„ are familiar with required safety devices
The machine must not be accessed or operated by:
î‚„ children
î‚„ people impaired by alcohol or drugs
Application
area
Be aware of the application area.
î‚„ Keep unauthorized personnel, children, and pets away from the machine.
î‚„ Remain aware of changing positions and the movement of other equipment and
personnel in the application area/job site.
Be aware of the application area.
î‚„ Do not operate the machine in areas that contain flammable objects, fuels, or
products that produce flammable vapors.
Safety
devices,
controls, and
attachments
Only operate the machine when:
î‚„ All safety devices and guards are in place and in working order.
î‚„ All controls operate correctly.
 The machine is set up correctly according to the instructions in the Operator’s
Manual.
î‚„ The machine is clean.
 The machine’s labels are legible.
wc_si000525gb.fm
14
Safety Information HSH 650G / HSH 700G
To ensure safe operation of the machine:
î‚„ Do not operate the machine if any safety devices or guards are missing or
inoperative.
î‚„ Do not modify or defeat the safety devices.
î‚„ Do not use accessories or attachments that are not approved by Wacker
Neuson.
Safe
operating
practices
When operating this machine:
 Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
When operating this machine:
î‚„ Do not operate a machine in need of repair.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while operating this
machine:
î‚„ Close-fitting work clothes that do not hinder movement
î‚„ Safety glasses with side shields
î‚„ Hearing protection
î‚„ Safety-toed footwear
wc_si000525gb.fm
15
HSH 650G / HSH 700G Safety Information
1.4 Service Safety
Service
training
Before servicing or maintaining the machine:
î‚„ Read and understand the instructions contained in all manuals delivered with
the machine.
î‚„ Familiarize yourself with the location and proper use of all controls and safety
devices.
î‚„ Only trained personnel shall troubleshoot or repair problems occurring with the
machine.
î‚„ Contact Wacker Neuson for additional training if necessary.
When servicing or maintaining this machine:
î‚„ Do not allow improperly trained people to service or maintain the machine.
Personnel servicing or maintaining the machine must be familiar with the
associated potential risks and hazards.
Precautions
Follow the precautions below when servicing or maintaining the machine.
î‚„ Read and understand the service procedures before performing any service to
the machine.
î‚„ All adjustments and repairs must be completed before operating the machine.
Do not operate the machine with a known problem or deficiency.
î‚„ All repairs and adjustments shall be completed by a qualified technician.
î‚„ Turn off the machine before performing maintenance or making repairs.
 Remain aware of the machine’s moving parts. Keep hands, feet, and loose
clothing away from the machine’s moving parts.
î‚„ Reinstall the safety devices and guards after repair and maintenance
procedures are complete.
Machine
modifications
When servicing or maintaining the machine:
î‚„ Use only accessories/attachments that are approved by Wacker Neuson.
When servicing or maintaining the machine:
î‚„ Do not defeat safety devices.
î‚„ Do not modify the machine without the express written approval of Wacker
Neuson.
Replacing
parts and
labels
î‚„ Replace worn or damaged components.
î‚„ Replace all missing and hard-to-read labels.
î‚„ When replacing electrical components, use components that are identical in
rating and performance to the original components.
î‚„ When replacement parts are required for this machine, use only Wacker
Neuson replacement parts or those parts equivalent to the original in all types of
specifications, such as physical dimensions, type, strength, and material.
wc_si000525gb.fm
16
Safety Information HSH 650G / HSH 700G
Cleaning
When cleaning and servicing the machine:
î‚„ Keep the machine clean and free of debris such as leaves, paper, cartons, etc.
î‚„ Keep the labels legible.
When cleaning the machine:
î‚„ Do not clean the machine while it is running.
î‚„ Never use gasoline or other types of fuels or flammable solvents to clean the
machine. Fumes from fuels and solvents can become explosive.
Personal
Protective
Equipment
(PPE)
Wear the following Personal Protective Equipment (PPE) while servicing or
maintaining this machine:
î‚„ Close-fitting work clothes that do not hinder movement
î‚„ Safety glasses with side shields
î‚„ Hearing protection
î‚„ Safety-toed footwear
In addition, before servicing or maintaining the machine:
î‚„ Tie back long hair.
î‚„ Remove all jewelry (including rings).
1.5 Safety Guidelines for Lifting the Machine
When lifting the machine:
î‚„ Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any
other type of lifting device used is attached securely and has enough weight-
bearing capacity to lift or hold the machine safely. See section Technical Data
for machine weight.
î‚„ Remain aware of the location of other people when lifting the machine.
 Only use the lifting points and tie-downs described in the Operator’s Manual.
î‚„ Make sure the transporting vehicle has sufficient load capacity and platform size
to safely transport the machine.
To reduce the possibility of injury:
î‚„ Do not stand under the machine while it is being lifted or moved.
î‚„ Do not get onto the machine while it is being lifted or moved.
wc_si000525gb.fm
17
HSH 650G / HSH 700G Safety Information
1.6 Safety Guidelines for Operating Combustion Burners
When using the machine:
î‚„ Clean up any spilled fuel immediately.
î‚„ Replace the fuel tank cap after refueling the machine.
î‚„ Refill the fuel tank in a well-ventilated area.
î‚„ Shut down the generator, if equipped, when refueling.
When using the machine:
When refueling the machine:
î‚„ Do not fill or drain the fuel tank near an open flame or while the machine is
running.
î‚„ Do not smoke when refueling the machine.
î‚„ Do not use gasoline, crankcase oil, or any oil containing gasoline.
DANGER
Exhaust gas from the burner contains carbon monoxide, a deadly poison. Exposure
to carbon monoxide can kill you in minutes.
f Never run the machine indoors or in an enclosed area unless the machine is
vented properly.
wc_si000525gb.fm
18
Safety Information HSH 650G / HSH 700G
1.7 Safety Guidelines for Operating Gensets
This machine is built with user safety in mind; however, like any electrical device it
can present serious hazards if improperly operated and serviced. Follow
instructions carefully. Should questions arise during operation or service of this
equipment, contact your Wacker Neuson dealer.
General
precautions
î‚„ Keep a multi-class, type ABC or equivalent fire extinguisher at hand when using
the genset. Refer to NFPA No. 10 for further information regarding fire
extinguishers.
î‚„ Do not use evaporative starting fluids. They are highly explosive.
î‚„ Do not store items such as excess oil, oil rags, or tools within the genset
compartment. Items stored within the genset compartment are a fire hazard and
can restrict cooling air.
Before
operating the
genset
î‚„ Know how to start, operate, and stop the genset before starting it.
î‚„ Obtain the proper training for operating the genset. Do not allow untrained
personnel to operate or service the genset.
î‚„ Check the fuel lines and the fuel tank for leaks and cracks before starting the
engine.
î‚„ Clean the genset of any spilled fuel.
DANGER
Carbon monoxide. Using a generator indoors CAN KILL YOU IN MINUTES.
Generator exhaust contains carbon monoxide (CO). This is a poison you cannot
see or smell. If you can smell the generator exhaust, you are breathing CO. But
even if you cannot smell the exhaust, you could be breathing CO.
WARNING
Electrocution hazard. Generators present special hazards during operation and
servicing. These include the risk of electrocution or severe electrical shock. Failure
to follow the safety information below can result in severe injury or death.
f Read and follow the safety instructions in this Operator’s Manual.
f Contact the genset manufacturer for additional information regarding the
genset.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety instructions could result in severe injury or
death.
f Read and follow the safety instructions in this Operator’s Manual.
f Contact the genset manufacturer for additional information regarding the
genset.
wc_si000525gb.fm
19
HSH 650G / HSH 700G Safety Information
Running the
genset
î‚„ Do not start the engine if fuel has spilled or a fuel odor is present.
î‚„ Keep the area around the exhaust pipe free of flammable materials.
î‚„ Do not smoke while operating the genset.
î‚„ Keep sparks, flames, electrical arcs, and other sources of ignition far away from
the genset.
î‚„ Do not touch the engine or muffler while the engine is running or immediately
after it has been turned off.
î‚„ Do not operate the genset with the maintenance covers off.
î‚„ Do not overload the genset. The total amperage of the tools and equipment
attached to the genset must not exceed the load rating of the genset.
î‚„ Do not operate the genset with wet hands.
î‚„ Do not remove the radiator cap when the genset is running or is hot.
Refueling
safety
When adding fuel to the fuel tank:
î‚„ Do not smoke.
î‚„ Do not refuel a hot or running engine.
When adding fuel to the fuel tank:
î‚„ Keep sparks, flames, electrical arcs, and other sources of ignition far away from
the genset.
î‚„ Refill the fuel tank only in a well-ventilated area.
î‚„ Reinstall the fuel tank cap after refueling.
Maintenance
safety
î‚„ Only a trained technician should attempt to repair the genset.
î‚„ Test procedures which require that the generator be running must be performed
using extreme caution.
î‚„ Make sure clothing and shoes are dry, stand on a dry wooden platform or rubber
insulating mat, and use tools with insulated handles when servicing the genset.
î‚„ Engine antifreeze is toxic to humans and animals. Clean up spills and dispose
of used engine antifreeze in accordance with local environmental regulations.
î‚„ Make sure all fasteners are secure and torqued properly.
wc_si000525gb.fm
20
Safety Information HSH 650G / HSH 700G
1.8 Safety Guidelines for Towing the Machine
When towing the machine:
 Do not tow the machine if the towing vehicle’s hitch or the trailer’s coupler are
damaged.
 Do not tow the machine if any of the trailer’s lug nuts are missing.
 Do not tow the machine if the trailer’s tires have less than 1.5 mm (1/16 inch) of
tread.
 Do not tow the machine unless the trailer’s brakes are functioning properly.
 Do not exceed the trailer manufacturer’s speed limitations.
When towing the machine:
 Only tow the machine when the trailer’s lug nuts are properly torqued.
 Only tow the machine when the trailer’s tires are properly inflated.
î‚„ Only tow the machine when all trailer lights are functioning correctly.
 Only tow the machine when the trailer’s safety chains are connected to the
towing vehicle in a crisscross pattern.
î‚„ Maintain extra distance between the towing vehicle and other vehicles.
î‚„ Avoid soft shoulders, curbs, and sudden lane changes
î‚„ Abide by all licensing requirements for your area.
If you have not driven a towing vehicle with trailer before, practice turning,
stopping, and backing up the towing vehicle with trailer in an area away from traffic.
Only drive the towing vehicle with trailer when you are confident in your ability to do
so.
WARNING
Risk of severe injury or death. Improper trailer condition and towing technique can
lead to an accident.
f Obey the trailer manufacturer’s instructions and the instructions below to reduce
the risk of an accident.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152

Wacker Neuson HSH650 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI