Samsung SyncMaster U70 User manual

Brand: Samsung

Model: SyncMaster U70

Category: LED displays

Type: User manual

This manual is also suitable for

SyncMaster U70

LCD Monitor

User Manual

Safety Instructions

Notational

Note

These safety instructions must be followed to ensure your safety and prevent property dam-

age.

Make sure to read the instructions carefully and use the product in the correct manner.

Warning / Caution

Otherwise, it may result in death or personal injury.

Otherwise, it may result in personal injury or property damage.

Installation

Be sure to contact an authorized Service Center when installing your

monitor in a location with heavy dust, high or low temperatures, high hu-

midity, and exposed to chemical substances and where it operates for 24

hours such as at airports, train stations etc.

Failure to do so may cause serious damage to your monitor.

When installing the product in a cabinet or rack, make sure that

the front end of the bottom of the product does not project out.

• Otherwise, it may fall or cause personal injury.

• Use a cabinet or rack of a size appropriate to the product.

Do not use a humidifier or kitchen table near the product.

• Otherwise, this may result in electric shock or fire.

Put down the monitor carefully.

• Failing to do so may damage the monitor.

Do not drop the monitor when moving it.

• This may cause damage to the product or the person carrying

it.

Do not install the product in a location low enough for children

to reach.

• Otherwise, it may fall and result in personal injury.

Others

Do not insert any metal, such as chopsticks, coins, pins and

steel, or flammable objects, such as matches or paper, inside the

product (input and output terminals, etc).

• Otherwise, this may result in electric shock or fire.

The product is a high voltage product. Ensure that users do not

disassemble, repair or modify the product themselves.

• Otherwise, this may result in electric shock or fire. If the product

needs to be repaired, contact a Service Center.

Safety Instructions

Introduction

Package Contents

Note

Please make sure the following items are included with your monitor.

If any items are missing, contact your dealer.

Contact a local dealer to buy optional items.

Unpacking

USB Monitor

Manuals

Quick Setup Guide Warranty Card

(Not available in all loca-

tions)

User's Guide

Cables

USB Cable

Others

Cleaning Cloth

Note

Cleaning Cloth is only provided for highly polished black products as a product feature.

Your Monitor

Front

Use this button to decrease the screen brightness for the 7" USB monitor.

The LED blinks when the screen brightness is decreased to the minimum

or when a screen brightness adjustment is completed.

Use this button to increase the screen brightness for the 7" USB monitor.

The LED blinks when the screen brightness is increased to the maximum

or when a screen brightness adjustment is completed.

Power button [ ] / Power indicator

Press the Power button to turn the 7" USB monitor on or off. The Power

indicator is displayed in blue when operating normally.

• Please activate the afterimage prevention function before using the 7"

USB auxiliary monitor.

• Activating the function

Turn off the USB monitor and hold down the Power button for five (5)

seconds. The monitor is turned on again and the afterimage prevention

program is activated while the LED blinks twice.

• Deactivating the function

Turn off the USB monitor and hold down the Power button for five (5)

seconds. The monitor is turned on again and the afterimage prevention

program is deactivated while the LED blinks once.

• What is the afterimage prevention function?

If you use the USB auxiliary monitor with the same image remaining on

the screen for a long period of time, an afterimage may develop on the

panel. The afterimage prevention function reduces afterimages on the

panel by turning the USB auxiliary monitor on and off automatically for

a short time (about 0.1 seconds) every thirty (30) minutes.

Introduction

Rear

Note

The configuration at the back of the product may vary from product to product.

Connect the terminal of the USB monitor

to the USB terminal of the PC using a USB

cable.

Kensington Lock

The Kensington Lock is a device used to

physically fix the system when using it in a

public place. The locking device has to be

purchased separately. The appearance and

locking method may differ from the illustra-

tion depending on the manufacturer. Refer to

the manual provided with the Kensington

Lock for proper use. The locking device has

to be purchased separately.

Note

The location of the Kensington Lock may be

different depending on its model.

Using the Anti-Theft Kensington Lock

1. Insert the locking device into the Ken-

sington slot on the Monitor ( ) and turn

it in the locking direction ( ).

2. Connect the Kensington Lock cable.

Introduction

3. Fix the Kensington Lock to a desk or a

heavy stationary object.

Introduction

Connections

Connecting the USB Monitor

• System Requirements

CPU : 1.73GHz or Later

OS : Windows XP Service Pack2 or later.

RAM : 512 MB RAM or more

USB : 1.1 or higher (USB 2.0 recommended)

Connect the terminal of the USB monitor to the USB terminal of the PC using a USB

cable.

Note

As power is supplied through a USB port, two (2) USB ports are used.

For more information on the driver installation and usage of the USB monitor, refer to Installing

the 7” USB Monitor Driver.

1. When adjusting the angle of the USB auxiliary monitor stand, do not use too much force.

This may cause the stand to break.

2. Make sure to use the 7” USB monitor after properly adjusting the angle of its stand.

This may cause the center of gravity of the product to change, leading causing the prod-

uct to fall resulting in damage or a malfunction.

Connections

Using the Software

Installing the 7” USB Monitor Driver

• System Requirements

CPU : 1.73GHz or Later

OS : Windows XP Service Pack2 or later.

RAM : 512 MB RAM or more

USB : 1.1 or higher (USB 2.0 recommended)

Installing Your USB Monitor

• Make sure to connect the USB cable and begin the installation after your

PC has booted.

• The Setup program requires about one minute for the installation. If you

turn the power off or remove the USB cable while the Setup program is

running, it may cause an error with the PC or the Windows operating sys-

tem.

• The optimal resolution for this USB monitor is 800x480.

1. Insert CD into the CD-ROM drive. Click "USB Monitor Driver"

2. Click "I Accept".

3. The progress window appears, as shown in the figure below.

4. If you connect your USB monitor to your PC, it recognizes the monitor and the "Found

New Hardware" wizard is displayed, as shown in the figure below.

When setup is finished, a monitor icon is created in the system tray at the bottom of the

monitor screen, and the information for the installed USB monitor is displayed.

5. When the installation is completed, configure the following settings to use multiple mon-

itors.

1. Right-click on the “Windows Desktop” and select “Properties” from the displayed menu.

The “Display Properties” window appears.

2. Select the “Settings” tab. A list of connected USB monitors is displayed.

3. Arrange the monitors displayed in the 'Display Properties' window in the order they are

actually used.

Using the Software

4. Then click "OK" button.

Configuring the 7" USB Monitor Display Information

1. When the driver setup for the USB monitor is finished, a monitor icon is created in the

system tray at the bottom of the monitor screen.

2. Click the monitor icon to display a list of connected USB monitors. Select the monitor for

which you want to configure the display settings. You can configure the "Screen Reso-

lution" , "Color Quality" and "Screen Rotation" settings for your monitor.

Checking the configuration

After the installation, you can check the configuration by following these steps.

1. Right-click “My Computer”, and select “Properties” - “System Properties” - the “Hardware

tab”.

2. Click “Device Manager”.

Using the Software

3. A list of the installed device will be displayed, as shown in the figure below.

- The Initial Screen Settings after Installing the Program

• Applicable mode: Extend mode

• Mode position: To the right of the primary screen

• Mode rotation: 0°

Restrictions on the 7” USB Monitor

Supported OS (Operating Systems)

• Windows XP

- Service Pack 1 or earlier: Unsupported

- Service Pack 2 or later: Supported

• Windows 2000

- Service Pack 3 or earlier: Not Supported

- Service Pack 4 or later: Supported

• Windows Server 2003: Not Supported

Using the Software

• Windows Vista: Supported.

To check the information on the operating system of your PC, right-click “My Computer” on

the “Windows Desktop” and select “Properties” from the displayed menu. Check the infor-

mation in the “General” tab of the “Computer Properties” window.

1. Because this USB monitor is recognized as a USB device, the DOS screen that appears

for general monitors when a PC is booting up is not displayed.

2. You cannot use the USB monitor for software using 3D hardware acceleration.

- Real Player (Expansion mode is not supported.)

- For most 3D games

- Programs running on the base of Direct X

3. Supported movie programs

- Power DVD

- Win DVD(Version 5 onwards)

- Windows Media Player (Version 10 or later is supported.)

- VLC

4. This monitor does not support the MagicTune program.

- The MagicRotation function may not function normally.

- If the MagicTune program is installed on your PC, it may not be compatible with this

monitor.

5. The USB monitor may not work normally with USB 1.0.

6. If the graphics card of your PC does not support WDDM, the extended mode may not

be available in Windows Vista.

Example) Some versions of the Matrox Card

Using the Software

Troubleshooting

Check List

Note

Before calling for assistance, check the information in this section to see if you can remedy

any problems yourself. If you do need assistance, please call the phone number on the In-

formation section or contact your dealer.

There is no image on the screen. I cannot turn on the monitor.

Q: Check whether the USB cable is connected correctly. Check whether the USB driver is

installed.

A: The USB monitor is recognized as a general USB device on a PC. If you turn the monitor

on or off quickly and repeatedly, a USB device problem may occur. Refer to the USB

device Troubleshooting section on the Microsoft customer support website.

1. Right-click the “My Computer” and click on “Properties”

2. The Device Manager is displayed.

3. From the “Action” menu, click ”Scan for hardware changes”. Reboot your PC.

The screen of the USB monitor freezes.

Q: Check the “Hardware acceleration” setting for your USB monitor in the “Display Prop-

erties” window.

A: Set the “Hardware acceleration” value to “Full”.

For more information on how to configure the settings, click here.

1. Right-click the “Windows Desktop” and click on “Properties”.

2. The “Display Properties” window appears.

Select the “Settings” tab and click on “Advanced”.

3. If the “Properties” window for your monitor is displayed, select the “Troubleshoot”

tab. Move the “Hardware acceleration” slide to “Full”.

My USB monitor is connected but the screen is blank.

Q: Does the Auto Installation program run when your USB monitor is connected?

A: Install the "USB Monitor Driver" from the provided CD. For more information on how to

install the driver, refer to "Installing and Using the Software".

I have connected the USB monitor but it does not boot up...

Q: For the One-Board Type computer which uses an i815 chipset motherboard, change

the Legacy USB support option to [Disabled] in the BIOS Setup menu and reboot the

computer.

A: (Example) Phoenix BIOS

If you turn on the computer, the ”Press F2 to enter SETUP” message is displayed on

the bottom of the screen. Press [F2] to display the BIOS Setup menu.

A: - Configuring the Settings

Set the Advanced -> Peripheral Configuration (Integrated Peripherals) -> Legacy USB

Support item to [Enabled]. Save the settings and reboot the computer.

A: - Entering the BIOS Setup screen may differ for each BIOS company. Refer to the user

manual for your PC.

For more information, visit the Microsoft website.

Q & A

Q: How I can clone or extend screen mode?

A: Open the”Display Properties” window and select the “Settings” tab,

Q: How can I remove the “USB Monitor Installation Program” completely?

A: Click “Add/Remove Programs” in the “Control Panel”. A list of “currently installed pro-

grams” is displayed.

Select “Samsung UbiSync Monitor” from the list and click “Remove”.

Q: The screen size of the USB monitor is larger than the actual monitor size.

A: If the primary monitor has a high resolution, screens are expanded beyond the recom-

mended resolution in Clone mode (USB monitor).

Q: The screen size of the USB monitor is smaller than the actual monitor size. The screen

is centered on the monitor.

A: If the primary monitor has a high resolution, screens are smaller than the recommended

resolution in Clone mode (USB monitor).

Q: I disconnected or turned off my USB monitor but my PC still displays the old monitor

information in the Display Properties window.

A: The deactivated USB monitors are such that the power to them is turned off or their

USB cables are disconnected. To remove this information, you have to remove the

“Samsung Ubisync Monitor” program from “Add/Remove Programs” in the “Control

Panel”.

If you remove the program you cannot use all the connected USB monitors.

If you want to use the USB monitor again, you have to setup the installation program

again.

Q: Icons and photos are broken or jagged in Clone mode (USB monitor).

A: This occurs because Windows does not send the screen updating information to Clone

mode if Extended mode is active on a single PC.

We recommend using the monitor in Extend mode.

Note

Before calling for assistance, check the information in this section to see if you can remedy

any problems yourself. If you do need assistance, please call the phone number on the In-

formation section or contact your dealer.

Troubleshooting

Specifications

General

Model Name SyncMaster U70

LCD Panel

Size 7" diagonal ( 17 cm)

Display area 152.4 mm(H) x 91.4 mm(V)

Pixel Pitch 0.1905 mm(H) x 0.1905 mm(V)

Synchronization

Horizontal 30 ~ 35 kHz

Vertical 59 ~ 62 Hz

Display Color

16.7M

Resolution

Optimum resolution 800x480@60Hz

Maximum resolution 800x480@60Hz

Input Signal, Terminated

USB interface (Compliant Digital RGB)

USB Format

TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V)

Maximum Pixel Clock

40 MHz (USB Mode)

Power Supply

DC 5V (USB Power) (+/- 10 %)

Signal Cable

USB Cable (1 up to 2 down), Detachable

Dimensions (W x H x D) / Weight (Simple Stand)

184.0 x 124.0 x 43.6 mm (7.2 x 4.9 x 1.7 inch) / 0.37kg (0.81 Ibs)

Note

Design and specifications are subject to change without prior notice.

Class B Equipment (Information Communication equipment for residential use)

This product complies with the Electromagnetic Compatibility Directives for residential use

and can be used in all areas including common residential areas. (Class B equipment emits

less electromagnetic waves than Class A equipment.)

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes,

the screen will be adjusted automatically. However, if the signal differs, the screen may go

blank while the power LED is on. Refer to the video card manual and adjusts the screen as

follows.

Display Mode Horizontal

Frequency

(kHz)

Vertical Fre-

quency (Hz)

Pixel Clock

(MHz)

Sync Polarity

(H/V)

IBM, 800 x 480 29.738 59.476 29.500 +/+

Horizontal Frequency

The time to scan one line connecting the right edge

to the left edge of the screen horizontally is called the

Horizontal Cycle and the inverse number of the Hor-

izontal Cycle is called the Horizontal Frequency.

Unit: kHz

Vertical Frequency

Like a fluorescent lamp, the screen has to repeat the

same image many times per second to display an

image to the user. The frequency of this repetition is

called the Vertical Frequency or Refresh Rate. Unit:

Specifications

Information

PRODUCT INFORMATION (Image Retention Free)

LCD Monitors and TVs may have image retention when switching from one image to another

especially after displaying a stationary image for a long time.

This guide is to demonstrate correct usage of LCD products in order to protect them from

Image retention.

Warranty

Warranty does not cover any damage caused by image retention.

Burn-in is not covered by the warranty.

What is Image retention ?

During normal operation of a LCD panel, pixel image retention doesn't occur. How-

ever, if the same image is displayed for a long time, a slight difference in electric

charge accumulates between the two electrodes which encase the liquid crystal.

This may cause the liquid crystal to build up in a certain areas of the display. Thus,

the previous image is retained when switching to a new video image. All display

products, including LCD, are subject to image retention. This is not a product de-

fect.

Please follow the suggestions below to protect your LCD from image retention.

Power Off, Screen Saver, or Power Save Mode

Ex)

• Turn the power off when using a stationary pattern.

• Turn the power off for 4 hours after 20 hours in use

• Turn the power off for 2 hours after 12 hours in use

• Use a Screen saver if possible

• Screen saver in one color or a moving image is recommended.

• Set the Monitor to power off with the PC Display Properties Power Scheme.

Suggestions for specific applications

Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We

recommend that you follow set up of your display system program as below:

Display Information together with Logo or Moving image cycle.

Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving

image for 1 minute.

Change the Color Information periodically (Use 2 different colors).

Ex) Rotate the Color Information with 2 colors every 30 minutes.

Avoid using a combination of characters and background color with large difference

in luminance.

Avoid using Grey colors, which can cause Image retention easily.

• Avoid: Colors with big difference in luminance (Black & White, Grey)

Ex)

• Recommended settings: Bright colors with little difference in luminance

• Change the characters color and background color every 30 minutes

Ex)

• Every 30 minutes, change the characters with movement.

Ex)

The best way to protect your monitor from Image retention is to set your PC or

System to operate a Screen Saver program when you are not using it.

Image retention may not occur when a LCD panel is operated under normal con-

ditions.

Information

Page is loading ...

Samsung SyncMaster U70 User manual

Brand: Samsung

Model: SyncMaster U70

Category: LED displays

Type: User manual

This manual is also suitable for

Download PDF

report

Samsung SyncMaster U70 User manual

This manual is also suitable for

Samsung SyncMaster U70 User manual

Related papers

Other documents