INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Small Secure Storage Shelf for Carts and Stands
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PAC730A/B/C
PAC730A/B/C Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components stored within or on the PAC730 does not
exceed 25 lbs (11.3 kg).
Installation Instructions PAC730A/B/C
3
DIMENSIONS
LEGEND
MEASUREMENTS: [MILLIMETERS]
INCHES
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
PAC730A/B/C Installation Instructions
4
TOOLS FOR INSTALLATION / PARTS
A (1)
[Storage Shelf]
B (1)
[Pole Attachment Plate]
C (1)
[Upper Bracket]
D (1)
[Hole Plug]
G (8)
[Bumper]
E (1)
5/32"
F (4)
1/4-20 x 3/8"
J (1)
[Key]
5/32"
(Included)
H (4)
1/4-20 x 3/4"
Installation Instructions PAC730A/B/C
5
INSTALLATION
NOTE: The PAC730 may be mounted on the Chief cart or
stand either by being attached mid-column on the cart
or stand column, or to the top of the cart or stand
column.
Mid-Column Attachment
1. Attach pole attachment plate (B) around the cart or stand
column to the storage shelf (A) using four 1/4-20 x 3/8"
button head cap screws (F). (See Figure 1)
2. Proceed to Adding Bumpers section.
Figure 1
Top of Column Attachment
1. Attach upper bracket (C) to storage shelf (A) using four
1/4-20 x 3/4" button head cap screws (H). (See Figure 2)
NOTE: The upper bracket (C) may be attached in two different
ways using the two hole patterns on the storage shelf
bottom. (See Figure 2)
Figure 2
2. Remove display from faceplate following instructions in the
cart or stand installation instructions.
1
(F) x 4
(B)
(A)
Cart/Stand
Column
1
(H) x 4
Hole
Pattern
PAC730A/B/C Installation Instructions
6
3. Remove and save four button head cap screws from top of
cart or stand column. (See Figure 3)
4. Place upper bracket with PAC730 onto top of cart or stand
column. (See Figure 3)
5. Fasten PAC730 to cart or stand using four button head cap
screws removed in Step 3. (See Figure 3)
Figure 3
6. Re-attach display to faceplate following installation
instructions included with cart or stand.
Adding Bumpers
Add eight bumpers (G) to fill the unused PEM nuts (inside the
PAC730) to protect the stored equipment. They can be added
to the unused PEM nuts in the circled areas. (See Figure 4)
Cable Management
1. Place hole plug (D) into 2" cable management opening.
(See Figure 4)
2. Run cables from components in storage shelf through the
plug in the cable management opening at the back of the
storage shelf. (See Figure 4)
Figure 4
4
Cart/Stand
Column
(A)
Faceplate
5
x 4
4
3
(G) x 8
[Bottom View]
Cable
Management
Opening
Installation Instructions PAC730A/B/C
7
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P 800.582.6480 / 952.894.6280
F 877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P +31 (0)40 2668620
F +31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P 852 2145 4099
F 852 2145 4477
PAC730A/B/C Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8807-002017 Rev00
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
06/10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief PAC730A Datasheet
- Category
- Storage chests & cabinets & trunks
- Type
- Datasheet
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Chief Welder CMA278 User manual
-
-
-
-
-
-
-
Chief FCA611 Installation guide
-
Chief Manufacturing PAS-100 User manual
-