Vivotek VIVOTEK IP8352, Network Camera, Supreme Series, with 1.3 Megapixel, with Focus Assist and WDR Enhanced for Outside Section User manual

IP8352IP8352

Supreme Night Visibility • 1.3MP • 60fps

VIVOTEK

2 - User's Manual

Table of Contents

Overview.......................................................................................................................................................4

Read Before Use ��5

Package Contents ��5

Symbols and Statements in this Document ��5

Physical Description ��6

Hardware Installation ��7

Network Deployment ��10

Network Deployment .................................................................................................................................. 11

Setting up the Network Camera over the Internet �� 11

Software Installation ��13

Ready to Use ��14

Accessing the Network Camera .................................................................................................................16

Using Web Browsers ��16

Using RTSP Players ��18

Using 3GPP-compatible Mobile Devices ��19

Using VIVOTEK Recording Software ��20

Main Page ..................................................................................................................................................21

Client Settings ............................................................................................................................................26

H�264 / MPEG-4 Media Options ��26

H�264 / MPEG-4 Protocol Options ��26

MP4 Saving Options ��27

Local Streaming Buffer Time ��27

Conguration ..............................................................................................................................................28

System > General settings ��29

System > Homepage layout ��31

System > Logs ��34

System > Parameters ��35

System > Maintenance ��36

Security > User Account ��40

Security > HTTPS (Hypertext Transfer Protocol over SSL) ��41

Security > Access List ��46

Security > IEEE 802�1x ��49

Network > General settings ��51

Network > Streaming protocols ��59

Network > QoS (Quality of Service) ��63

Network > DDNS ��65

Manual setup ��66

Network > SNMP (Simple Network Management Protocol)

��

68

Media > Image ��69

General settings ��69

VIVOTEK

User's Manual - 3

Day/Night Settings �� 70

Preference �� 71

Exposure �� 73

Privacy mask �� 76

Media > Video �� 77

Stream settings

��

77

Media > Audio�� 81

Audio Settings �� 81

PTZ > PTZ settings �� 82

Digital PTZ Operation (E-PTZ Operation) �� 82

Event > Event settings �� 85

Event �� 85

Add server �� 88

Add media �� 92

Applications > Motion detection�� 98

Applications > DI and DO �� 101

Applications > Tampering detection �� 101

Recording > Recording settings �� 102

Local storage > SD card management �� 107

SD card staus �� 107

SD card control �� 107

Local storage > Content management �� 108

Searching and Viewing the Records �� 108

Search Results 1 �� 08

Appendix ................................................................................................................................................................. 110

URL Commands for the Network Camera �� 110

1� Overview �� 110

2� Style Convention �� 110

Technical Specications �� 180

Technology License Notice �� 181

MPEG-4 AAC Technology �� 181

MPEG-4 Visual Technology �� 181

AMR-NB Standard �� 181

Electromagnetic Compatibility (EMC) �� 182

VIVOTEK

4 - User's Manual

Overview

VIVOTEK IP8352 is a best-in-class 1�3-Megapixel bullet network camera designed for diverse

outdoor applications� Incorporated with a progressive scan CMOS sensor with exceptional low

lux capabilities, the IP8352 captures not only razor-sharp images of fast-moving objects during

the daytime, but also offers unparalleled night visibility under low light conditions�

Equipped with VIVOTEK’s self-developed next-generation SoC, the IP8352 supports high-

performance H�264/MPEG-4/MJPEG compression technology and offers extra smooth

video quality up to 60 fps @ 720p and 30fps @ 1�3MP� Furthermore, the IP8352 boasts a

number of innovative technologies, including Activity Adaptive Streaming and Gigabit Ethernet

Transmission, giving a user the utmost in bandwidth exibility and storage efciency.

To adapt to constantly changing lighting conditions, the IP8352 comes with a removable IR-

cut lter and built-in IR illuminators for both day and night applications. Its IP67-rated housing

protects the camera body against rain and dust and ensures operation under extreme weather

conditions� For complete installation and prevention of tampering and vandalism, the IP8352 is

also packaged with a mounting bracket that conceals all cabling�

With other advanced features such as tamper detection, 802�3af compliant PoE, MicroSD/SDHC

card slot for on-board storage, Gigabit Ethernet Transmission, plus Supreme Night Visibility and

60fps high denition video quality, the IP8352 is the best choice for the most demanding outdoor

surveillance applications such as parking lots, entrances, housing communities, and much more�

VIVOTEK

User's Manual - 5

■ IP8352 - the Network Camera

■ Alignment Sticker

■ Sun Shield, Wrench/RJ45 Female/Female

Coupler/Double-sided Tape/Screws

■ Power Adapter

■ Wall Mount Bracket & Mounting Plate

■ Waterproof Connector (Optional)

■ Moisture Absorber

■ Quick Installation Guide / Warranty Card

■ Software CD

Read Before Use

The use of surveillance devices may be prohibited by law in your country� The Network Camera is not

only a high-performance web-ready camera but can also be part of a exible surveillance system. It is

the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for

its intended use�

It is important to rst verify that all contents received are complete according to the Package Contents

listed below� Take note of the warnings in the Quick Installation Guide before the Network Camera is

installed; then carefully read and follow the instructions in the Installation chapter to avoid damage due to

faulty assembly and installation� This also ensures the product is used properly as intended�

The Network Camera is a network device and its use should be straightforward for those who have basic

networking knowledge� It is designed for various applications including video sharing, general security/

surveillance, etc� The Configuration chapter suggests ways to best utilize the Network Camera and

ensure proper operations� For creative and professional developers, the URL Commands of the Network

Camera section serves as a helpful reference to customizing existing homepages or integrating with the

current web server�

Package Contents

Symbols and Statements in this Document

i

INFORMATION: provides important messages or advices that might help prevent inconvenient

or problem situations�

NOTE: Notices provide guidance or advices that are related to the functional integrity of the

machine�

Tips: Tips are useful information that helps enhance or facilitae an installation, function, or

process�

WARNING! or IMPORTANT!: These statements indicate situations that can be dangerous or

hazardous to the machine or you�

Electrical Hazard: This statement appears when high voltage electrical hazards might occur

to an operator�

VIVOTEK

6 - User's Manual

Physical Description

IR LEDs

Lens

Light Sensor

Zoom Controller

Focus Controller

Reset Button

General I/O

Terminal Block

SD/SDHC Card Slot

General I/O Terminal Block

Gb Ethernet

RJ45 Plug

Power Cord Socket

+ AC 24V +

- AC 24V -

When inserting an SD/SDHC

card, note the orientation of

the contacts�

VIVOTEK

User's Manual - 7

Hardware Installation

1� Attach the alignment sticker to the wall� Drill three holes into the wall� Then hammer the

supplied plastic anchors into the holes and secure the plate with supplied screws�

2� Feed the cables through the front opening of the wall mount bracket� (If you want to use

external devices such as sensors and alarms, please refer to the assembling steps on the

next page�)

3� Hang the wall mount bracket on the plate�

4� Fix the Network Camera on the wall mount bracket with two screws on both sides�

5� Secure the wall mount bracket with the supplied screws�

6� Adjust the angle of the wall mount bracket to aim at the shooting area�

1

2

5

4

3

6

5

4

6

IMPORTANT!

The supplied L-type hex key wrenches are exclusively

designed to match each screw� In case you will need to

adjust the lens later, do not discard the wrenches�

VIVOTEK

8 - User's Manual

1 Power +12V

2 Digital Output

3 Digital Input

4 Ground

5 RS485 +

6 RS485 -

7 Ground

8 Audio Input

9 Ground

10 Audio Output

87654321 109

Waterproof Connector

1� Disassemble the components of the waterproof connector into part (A) ~ (F) as shown above�

2� Remove the rubber stopper from the bottom of the Network Camera and secure the rubber (A)

and screw nut (B) tightly�

3� Open the back cover of the Network Camera�

4� If you have external devices such as sensors and alarms, feed the cables through the

waterproof connector (F --> E --> C --> A+B) as the illustration shown below� Then refer to

the pin denition to connect them to the general I/O terminal block. Note: The recommended

cable gauge is 2�0 ~ 2�8 mm�

5� Push the seal (C) into the housing (E)�

6� Insert the seals (D) into the empty holes on the seal (C) to avoid moisture�

7� Secure the sealing nut (F) tightly�

8� Tighten the back cover�

9� Remove rubber (G) and feed the cables through the wall mount bracket�

Rubber (A)

Screw Nut (B)

Seal (C)

Seals (D)

Housing (E)

Sealing Nut (F)

Components of the Waterproof Connector

IO Block Pin Denitions

Assembling Steps

(A)+(B)

2

6

(E)

(C)

(F)

(D)

(C)

4

7

(E)

(F)

3

(C)

5

8

9

(F)

(G)

VIVOTEK

User's Manual - 9

DI/DO Diagram

Please refer to the following illustration for the connection method�

Hardware Reset

The reset button is used to reset the system or restore the factory default settings� Sometimes

resetting the system can return the camera to normal operation� If the system problems remain

after reset, press the reset button longer to restore the factory settings and install again�

Reset: Press and release the recessed reset button with a straightened paper clip� Wait for the

Network Camera to reboot�

Restore: Press and hold the recessed reset button for at least several seconds to restore� Note

that all settings will be restored to factory defaults�

SD/SDHC Card Capacity

This network camera is compliant with Micro SD/SDHC 32GB and other preceding standard SD

cards�

12V

+12V

Digital output

PIN 1

Power+12V

PIN 2

Digital input

PIN 3

Ground

PIN 4

Reset Button

VIVOTEK

10 - User's Manual

The Network Camera is PoE-compliant, allowing transmission of power and data via a single

Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enabled

switch via Ethernet cable�

POWER

COLLISION

LINK

RECEIVE

PARTITION

1

2

3

4

5

Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE

switch�

POWER

COLLISION

LINK

RECEIVE

PARTITION

1

2

3

4

5

Network Deployment

When using a PoE-enabled switch

PoE Switch

RJ45 Female/

Female Coupler

When using a non-PoE switch

RJ45 Female/

Female Coupler

PoE Power

Injector

(Optional)

Non-PoE Switch

VIVOTEK

User's Manual - 11

Network Deployment

Setting up the Network Camera over the Internet

There are several ways to set up the Network Camera over the Internet� The rst way is to set

up the Network Camera behind a router� The second way is to utilize a static IP� The third way is

to use PPPoE�

Internet connection via a router

Before enabling the access to the Network Camera over the Internet, make sure you have a

router and follow the steps below�

1� Connect your Network Camera behind a router, the Internet environment is illustrated below�

Regarding how to obtain your IP address, please refer to Software Installation on page 13 for

details�

2� In this case, if the Local Area Network (LAN) IP address of your Network Camera is

192�168�0�3, please forward the following ports for the Network Camera on the router�

■ Secondary HTTP port

■ RTSP port

■ RTP port for audio

■ RTCP port for audio

■ RTP port for video

■ RTCP port for video

If you have changed the port numbers on the Network page, please open the ports

accordingly on your router� For information on how to forward ports on the router, please refer

to your router’s user’s manual�

3� Find out the public IP address of your router provided by your ISP (Internet Service Provider)�

Use the public IP and the secondary HTTP port to access the Network Camera from the

Internet� Please refer to Network Type on page 51 for details�

IP address : 192.168.0.3

Subnet mask : 255.255.255.0

Default router : 192.168.0.1

IP address : 192.168.0.2

Subnet mask : 255.255.255.0

Default router : 192.168.0.1

LAN (Local Area Network)

Router IP address : 192.168.0.1

WAN (Wide Area Network )

Router IP address : from ISP

Cable or DSL Modem

L

A

N (

Local Area Network)

R

o

u

t

e

r

I

P

a

d

r

e

s

:

W

A

N (Wide Area Network )

R

o

u

t

e

r

I

P

a

d

r

e

s

:

f

r

o

m

I

S

P

POWER

COLLISION

LINK

RECEIVE

PARTITION

1

2

3

4

5

Internet

I

P

a

d

r

e

s

:

1

9

2

.

1

6

8

.

0

.

3

S

u

b

n

e

t

m

a

s

k

:

2

5

2

5

2

5

0

VIVOTEK

12 - User's Manual

Internet connection with static IP

Choose this connection type if you are required to use a static IP for the Network Camera�

Please refer to LAN conguration on page 51 for details.

Internet connection via PPPoE (Point-to-Point over Ethernet)

Choose this connection type if you are connected to the Internet via a DSL Line� Please refer to

PPPoE on page 49 for details�

VIVOTEK

User's Manual - 13

Software Installation

Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up

your Network Camera on the LAN�

1� Install IW2 under the Software Utility directory from the software CD�

Double click the IW2 shortcut on your desktop to launch the program�

2� The program will conduct an analysis of your network environment�

After your network environment is analyzed, please click Next to continue the program�

3� The program will search for all VIVOTEK network devices on the same LAN�

4� After a brief search, the main installer window will pop up� Double-click on the MAC address

that matches the one printed on the camera label or the S/N number on the package box label

to open a browser management session with the Network Camera�

Installation

Wizard 2

IW

2

0002D107258A

00-02-D1-07-25-8A 192.168.5.151 FD8162

0002D1083236

VIVOTEK

14 - User's Manual

Ready to Use

1� A browser session with the Network Camera should prompt as shown below�

2� You should be able to see live video from your camera� You may also install the 32-channel

recording software from the software CD in a deployment consisting of multiple cameras� For

its installation details, please refer to its related documents�

3� Unscrew the zoom controller to adjust the zoom

factor� Upon completion, tighten the zoom

controller�

4� Unscrew the focus controller to adjust the focus

range� Upon completion, tighten the focus

controller�

T

W

∞

N

3

4

VIVOTEK

User's Manual - 15

5� Tighten the lens cover�

6� Replace the moisture absorber with a new one if you open the back cover during the

installation procedure�

5

6

IMPORTANT!

1

2

3

Please tear down the aluminum

foil vacuum bag and take out the

moisture absorber, and then replace

it with the absorber in kit using a

double-sided tape�

NOTE:

If you want to use the supplied sun shield for outdoor environments, please follow the steps

below to install:

1� Tighten the supplied two screws�

2� Attach the supplied sun shield to the Network Camera and slide it to the desired position�

3� Fix the sun shield with the supplied two screws�

VIVOTEK

16 - User's Manual

Accessing the Network Camera

This chapter explains how to access the Network Camera through web browsers, RTSP players,

3GPP-compatible mobile devices, and VIVOTEK recording software�

Using Web Browsers

Use Installation Wizard 2 (IW2) to access the Network Cameras on the LAN�

If your network environment is not a LAN, follow these steps to access the Netwotk Camera:

1� Launch your web browser (ex� Microsoft

®

Internet Explorer or Mozilla Firefox)�

2. Enter the IP address of the Network Camera in the address eld. Press Enter�

3� The live video will be displayed in your web browser�

4. If it is the rst time installing the VIVOTEK network camera, an information bar will prompt as

shown below� Follow the instructions to install the required plug-in on your computer�

NOTE:

For Mozilla Firefox or Netscape users, your browser will use Quick Time to stream live video�

If you do not have Quick Time on your computer, please download Quick Time from Apple

Inc's website, and then launch your web browser�

VIVOTEK

User's Manual - 17

To enable the ActiveX

®

Controls for your browser:

3� Refresh your web browser, then install the ActiveX

®

control� Follow the instructions to

complete installation�

1� Choose Tools > Internet Options > Security

> Custom Level�

2� Look for Download signed ActiveX

®

controls;

select Enable or Prompt� Click OK�

NOTE:

1� By default, your Network Camera is not password-protected� To prevent unauthorized

access, it is highly recommended to congure a password for your camera later.

For more

information about how to enable password protection, please refer to Security on page 40

�

2� If you see a dialogue box indicating that your security settings prohibit running ActiveX

Controls®, please enable ActiveX Controls for your browser�

VIVOTEK

18 - User's Manual

Using RTSP Players

To view the H�264/MPEG-4 streaming media using RTSP players, you can use one of the

following players that support RTSP streaming�

Quick Time Player

Real Player

As most ISPs and players only allow RTSP streaming through port number 554, please set the

RTSP port to 554� For more information, please refer to RTSP Streaming on page 60�

For example:

4. The live video will be displayed in your player. For more information on how to congure the

RTSP access name, please refer to RTSP Streaming on page 60 for details�

1� Launch the RTSP player�

2� Choose File > Open URL� A URL dialog box will prompt�

3� The address format is rtsp://<ip address>:<rtsp port>/<RTSP streaming access name for

stream1 or stream2>

rtsp://192.168.5.151:554/live.sdp

Video 16:38:01 2011/03/25

VIVOTEK

User's Manual - 19

Using 3GPP-compatible Mobile Devices

To view the streaming media through 3GPP-compatible mobile devices, make sure the Network

Camera can be accessed over the Internet� For more information on how to set up the Network

Camera over the Internet, please refer to Setup the Network Camera over the Internet on page

11�

To utilize this feature, please check the following settings on your Network Camera:

1� Because most players on 3GPP mobile phones do not support RTSP authentication, make

sure the authentication mode of RTSP streaming is set to disable�

For more information, please refer to RTSP Streaming on page 60�

2� As the the bandwidth on 3G networks is limited, you will not be able to use a large video size�

Please set the video and audio streaming parameters as listed below�

For more information, please refer to Stream settings on page 77�

Video Mode MPEG-4

Frame size 176 x 144

Maximum frame rate 5 fps

Intra frame period 1S

Video quality (Constant bit rate) 40kbps

Audio type (GSM-AMR) 12.2kbps

3� As most ISPs and players only allow RTSP streaming through port number 554, please set

the RTSP port to 554� For more information, please refer to RTSP Streaming on page 60�

4� Launch the player on the 3GPP-compatible mobile devices (e�g�, Real Player)�

5. Type the following URL commands in the URL eld.

The address format is rtsp://<public ip address of your camera>:<rtsp port>/<RTSP streaming

access name for stream 3>�

For example:

rtsp://192.168.5.151:554/live.sdp

VIVOTEK

20 - User's Manual

Using VIVOTEK Recording Software

The product software CD also contains recording software, allowing simultaneous monitoring

and video recording for multiple Network Cameras� Please install the recording software; then

launch the program to add the Network Camera to the Channel list� For detailed information

about how to use the recording software, please refer to the user’s manual of the software or

download it from http://www�vivotek�com�

Vivotek VIVOTEK IP8352, Network Camera, Supreme Series, with 1.3 Megapixel, with Focus Assist and WDR Enhanced for Outside Section, IP8352, IP8352 Supreme, IP8352 TW Supreme User manual

Related papers

Other documents