Philips LX8300SA User manual

Philips
Brand
Philips
Model
LX8300SA
Category
Home cinema systems
Type
User manual
1
3139 115 23261
DVD VIDEO / SACD HOME THEATER SYSTEM
LX8300SA
User manual
Visit us at www.p4c.philips.com for service support
001-047-LX83-22-Eng 6/9/04, 1:52 PM1
2
3139 115 23261
Norge
Typeskilt finnes på apparatens underside.
Observer: Nettbryteren er sekundert
innkoplet. Den innebygde netdelen er
derfor ikke frakoplet nettet så lenge
apparatet er tilsluttet nettkontakten.
For å redusere faren for brann eller elektrisk
støt, skal apparatet ikke utsettes for regn eller
fuktighet.
Italia
DICHIARAZIONE DI CONFORMITA’
Si dichiara che l’apparecchio LX8300SA, Philips
risponde alle prescrizioni dell’art. 2 comma 1 del
D.M. 28 Agosto 1995 n. 548.
Fatto a Eindhoven
Philips Consumer Electronics
Philips, Glaslaan 2
5616 JB Eindhoven, The Netherlands
CAUTION
Use of controls or adjustments or
performance of procedures other than
herein may result in hazardous
radiation exposure or other unsafe
operation.
VAROITUS
Muiden kuin tässä esitettyjen
toimintojen säädön tai asetusten
muutto saattaa altistaa vaaralliselle
säteilylle tai muille vaarallisille
toiminnoille.
Important notes for users in the
U.K.
Mains plug
This apparatus is fitted with an approved 13
Amp plug. To change a fuse in this type of plug
proceed as follows:
1 Remove fuse cover and fuse.
2 Fix new fuse which should be a BS1362 5 Amp,
A.S.T.A. or BSI approved type.
3 Refit the fuse cover.
If the fitted plug is not suitable for your socket
outlets, it should be cut off and an appropriate
plug fitted in its place.
If the mains plug contains a fuse, this should
have a value of 5 Amp. If a plug without a fuse
is used, the fuse at the distribution board
should not be greater than 5 Amp.
Note: The severed plug must be disposed of to
avoid a possible shock hazard should it be
inserted into a 13 Amp socket elsewhere.
How to connect a plug
The wires in the mains lead are coloured with
the following code: blue = neutral (N),
brown = live (L).
As these colours may not correspond with the
colour markings identifying the terminals in
your plug, proceed as follows:
– Connect the blue wire to the terminal
marked N or coloured black.
– Connect the brown wire to the terminal
marked L or coloured red.
– Do not connect either wire to the earth
terminal in the plug, marked E (or e) or
coloured green (or green and yellow).
Before replacing the plug cover, make certain
that the cord grip is clamped over the sheath
of the lead - not simply over the two wires.
Copyright in the U.K.
Recording and playback of material may
require consent. See Copyright Act 1956 and
The Performer’s Protection Acts 1958 to 1972.
001-047-LX83-22-Eng 6/9/04, 2:01 PM2
3
3139 115 23261
CAUTION
VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AVOID
EXPOSURE TO BEAM
ADVARSEL
SYNLIG OG USYNLIG
LASERSTRÅLING VED ÅBNING
UNDGÅ UDSÆTTELSE FOR STRÅLING
VARNING
SYNLIG OCH OSYNLIG
LASERSTRÅLNING NÄR DENNA DEL
ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
VARO!
AVATTAESSA OLET ALTTIINA
NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE
LASER SÄTEILYLLE. ÄLÄ KATSO
SÄTEESEEN
VORSICHT
SICHTBARE UND UNSICHTBARE
LASERSTRAHLUNG WENN
ABDECKUNG GEÖFFNET NICHT DEM
STRAHL AUSSETSEN
ATTENTION
RAYONNEMENT LASER VISIBLE ET
INVISIBLE EN CAS D’OUVERTURE
EXPOSITION DANGEREUSE AU
FAISCEAU
LASER
Type Semiconductor laser
GaAlAs
Wave length 650~660 nm (DVD)
784~796 nm (CD)
Output Power 7 mW (DVD)
10 mW (VCD/CD)
Beam divergence 60 degree
This product complies with the radio
interference requirements of the
European Community.
Manufactured under license from Dolby
Laboratories. “Dolby”, “Pro Logic” and
the double-D symbol are trademarks of
Dolby Laboratories.
Manufactured under license from
Digital Theater Systems, Inc. U.S. Pat.
Noís. 5,451,942; 5,956,674; 5,974,380;
5,978,762; 6,226,616; 6,487,535 and
other U.S. and world-wide patents
issued and pending. “DTS” and “DTS
Digital Surround” are registered
trademarks of Digital Theater Systems,
Inc. Copyright 1996, 2003 Digital Inc.
All Rights Reserved.
This DVD player is in
conformity with the EMC
directive and low-voltage
directive.
For Customer Use:
Read carefully the information located at
the bottom of your DVD VIDEO player
and enter below the Serial No. Retain this
information for future reference.
Model No. DVD VIDEO LX8300SA
Serial No. _______________
‘CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE ‘STANDARD
DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR TV SET COMPATIBILITY WITH THIS
MODEL 525p AND 625p DVD PLAYER, PLEASE
CONTACT OUR CUSTOMER SERVICE CENTRE’.
DivX
®
, DivX Certified, and
associated logos are
trademarks of
DivXNetworks, Inc and are
used under license.
001-047-LX83-22-Eng 6/9/04, 2:01 PM3
4
3139 115 23261
DK
Advarsel: Usynlig laserstråling ved åbning
når sikkerhedsafbrydere er ude af funktion.
Undgå utsættelse for stråling.
Bemærk: Netafbryderen er sekundært
indkoblet og ofbryder ikke strømmen fra
nettet. Den indbyggede netdel er derfor
tilsluttet til lysnettet så længe netstikket
sidder i stikkontakten.
S
Klass 1 laseraparat
Varning! Om apparaten används på annat
sätt än i denna bruksanvisning specificerats,
kan användaren utsättas för osynlig
laserstrålning, som överskrider gränsen för
laserklass 1.
Observera! Stömbrytaren är sekundärt
kopplad och bryter inte strömmen från
nätet. Den inbyggda nätdelen är därför
ansluten till elnätet så länge stickproppen
sitter i vägguttaget.
SF
Luokan 1 laserlaite
Varoitus! Laitteen käyttäminen muulla kuin
tässä käyttöohjeessa mainitulla tavalla
saattaa altistaa käyttäjän
turvallisuusluokan 1 ylittävälle
näkymättömälle lasersäteilylle.
Oikeus muutoksiin varataan. Laite ei saa
olla alttiina tippu-ja roiskevedelle.
Huom. Toiminnanvalitsin on kytketty
toisiopuolelle, eikä se kytke laitetta irti
sähköverkosta. Sisäänrakennettu verkko-
osa on kytkettynä sähköverkkoon aina
silloin, kun pistoke on pistorasiassa.
Due to the inconsistency of disc formats provided
by various disc manufacturers, your DVD system/
player/recorder may require a playability
enhancement or upgrade. As DVD technology
advances, these enhancement will become
common and will be easy to complete.
Go to www. p4c.philips.com for software upgarde.
En raison de la diversité des formats utilisés par les
fabricants, votre système DVD peut nécessiter
l'ajout de périphériques ou une mise à niveau
logicielle. Au fur et à mesure des progrès de la
technologie DVD, ces périphériques se font de plus
en plus courants et aisés à intégrer. Pour
télécharger la mise à niveau logicielle, visitez le site
www.p4c.philips.com.
Debido a los diferentes formatos de discos
disponibles en el mercado, es posible que deba
realizar mejoras o actualizaciones en el sistema de
DVD relativas a las funciones de reproducción.
Conforme la tecnología DVD avanza, estas mejoras
estarán al alcance de todo tipo de usuarios y se
podrán llevar a cabo fácilmente. Visite la página
“www.p4c. philips.com” para buscar información
sobre actualizaciones de software.
Da das Disk-Format je nach Hersteller verschieden
ist, ist für Ihr DVD-System möglicherweise die
Erweiterung der Spielbarkeit oder eine
Aktualisierung erforderlich. Da die
DVD-Technologie sich ständig weiterentwickelt,
werden sich diese Erweiterungen durchsetzen und
einfach auszuführen sein. Gehen Sie zu für Ihre
Software-Aktualisierung zu „www.p4c. philips.com“.
Doordat fabrikanten verschillende schijfindelingen
aanbieden, moet uw dvd-systeem mogelijk worden
geüpgradet of uitgebreid. Naarmate de
dvd-technologie zich verder ontwikkelt, zullen
deze uitbreidingen normaal worden en zult u ze
gemakkelijk kunnen uitvoeren. Ga naar
"www.p4c. philips.com" om uw software te
upgraden.
A causa della differenza di formato tra i dischi
forniti dai vari produttori, il sistema DVD potrebbe
richiedere un potenziamento o aggiornamento
della riproducibilità. Col progredire della tecnologia
DVD, questi potenziamenti diverranno comuni e
facili da implementare. Visitare
“www.p4c. philips.com” per scaricare gli
aggiornamenti del software.
001-047-LX83-22-Eng 6/9/04, 2:01 PM4
5
3139 115 23261
Language Code
Abkhazian 6566
Afar 6565
Afrikaans 6570
Amharic 6577
Arabic 6582
Armenian 7289
Assamese 6583
Avestan 6569
Aymara 6589
Azerhaijani 6590
Bahasa Melayu 7783
Bashkir 6665
Belarusian 6669
Bengali 6678
Bihari 6672
Bislama 6673
Bokmål, Norwegian 7866
Bosanski 6683
Brezhoneg 6682
Bulgarian 6671
Burmese 7789
Castellano, Español 6983
Catalán 6765
Chamorro 6772
Chechen 6769
Chewa; Chichewa; Nyanja 7889
9072
Chuang; Zhuang 9065
Church Slavic; Slavonic 6785
Chuvash 6786
Corsican 6779
Česky 6783
Dansk 6865
Deutsch 6869
Dzongkha 6890
English 6978
Esperanto 6979
Estonian 6984
Euskara 6985
 6976
Faroese 7079
Français 7082
Frysk 7089
Fijian 7074
Gaelic; Scottish Gaelic 7168
Gallegan 7176
Georgian 7565
Gikuyu; Kikuyu 7573
Guarani 7178
Gujarati 7185
Hausa 7265
Herero 7290
Hindi 7273
Hiri Motu 7279
Hrwatski 6779
Ido 7379
Interlingua (International)7365
Interlingue 7365
Inuktitut 7385
Inupiaq 7375
Irish 7165
Íslenska 7383
Italiano 7384
Ivrit 7269
Japanese 7465
Javanese 7486
Kalaallisut 7576
Kannada 7578
Kashmiri 7583
Kazakh 7575
Kernewek 7587
Khmer 7577
Kinyarwanda 8287
Kirghiz 7589
Komi 7586
Korean 7579
Kuanyama; Kwanyama 7574
Kurdish 7585
Lao 7679
Latina 7665
Latvian 7686
Letzeburgesch; 7666
Limburgan; Limburger 7673
Lingala 7678
Lithuanian 7684
Luxembourgish; 7666
Macedonian 7775
Malagasy 7771
Magyar 7285
Malayalam 7776
Maltese 7784
Manx 7186
Maori 7773
Marathi 7782
Marshallese 7772
Moldavian 7779
Mongolian 7778
Nauru 7865
Navaho; Navajo 7886
Ndebele, North 7868
Ndebele, South 7882
Ndonga 7871
Nederlands 7876
Nepali 7869
Norsk 7879
Northern Sami 8369
North Ndebele 7868
Norwegian Nynorsk; 7878
Occitan; Provencal 7967
Old Bulgarian; Old Slavonic 6785
Oriya 7982
Oromo 7977
Ossetian; Ossetic 7983
Pali 8073
Panjabi 8065
Persian 7065
Polski 8076
Português 8084
Pushto 8083
Russian 8285
Quechua 8185
Raeto-Romance 8277
Romanian 8279
Rundi 8278
Samoan 8377
Sango 8371
Sanskrit 8365
Sardinian 8367
Serbian 8382
Shona 8378
Shqip 8381
Sindhi 8368
Sinhalese 8373
Slovensky 8373
Slovenian 8376
Somali 8379
Sotho; Southern 8384
South Ndebele 7882
Sundanese 8385
Suomi 7073
Swahili 8387
Swati 8383
Svenska 8386
Tagalog 8476
Tahitian 8489
Tajik 8471
Tamil 8465
Tatar 8484
Telugu 8469
Thai 8472
Tibetan 6679
Tigrinya 8473
Tonga (Tonga Islands) 8479
Tsonga 8483
Tswana 8478
Türkçe 8482
Turkmen 8475
Twi 8487
Uighur 8571
Ukrainian 8575
Urdu 8582
Uzbek 8590
Vietnamese 8673
Volapuk 8679
Walloon 8765
Welsh 6789
Wolof 8779
Xhosa 8872
Yiddish 8973
Yoruba 8979
Zulu 9085
001-047-LX83-22-Eng 6/9/04, 2:01 PM5
6
3139 115 23271
English
Language Code ...................................... 5
General Information
Supplied accessories ................................... 8
Care and safety information ..................... 8
Connections
Step 1: Assemble the speakers ................. 9
Step 2: Connecting DVD system
and speakers to the AV subwoofer ....... 10
Step 3: Connecting TV.............................. 11
Using Scart jacks .................................. 11
Using S-Video jack ............................... 11
Using Composite Video jack .............. 11
Step 4: Connecting a Progressive
ScanTV ......................................................... 12
Using Component Video jacks
(Y Pb Pr)................................................. 12
Step 5: Placing the speakers and AV
subwoofer ................................................... 12
Step 6: Connecting FM/MW antennas ... 13
Step 7: Connecting the power cord ..... 13
Connections (optional)
Connecting a VCR or Cable/
Satellite Box ............................................... 14
Viewing and listening to the
playback .................................................. 14
Using the VCR for recording
DVD playback ....................................... 14
Connecting digital audio equipment ..... 15
Listening to the playback .................... 15
Functional Overview
Remote Control ................................. 16–17
Top and front panel .................................. 18
Getting Started
Step 1: Inserting batteries into the
remote control .......................................... 19
Using the remote control to
operate the system .............................. 19
Step 2: Setting the TV ............................... 19
Switching to YUV video output
setting ..................................................... 19
Selecting the colour system that
corresponds to your TV ..................... 20
Setting the TV Display ......................... 20
Step 3: Setting language preferences ..... 21
On-Screen Display (OSD) language . 21
Audio, Subtitle and Disc menu
languages ................................................ 21
Step 4: Setting the speakers’ channels .. 22
Disc Operations
Playable discs .............................................. 23
Playing discs ................................................ 23
Auto Eco Power standby mode ........ 24
Basic playback controls ............................ 24
Selecting various repeat/shuffle
functions ...................................................... 24
Repeat play mode ................................ 24
Repeating a section within a
chapter/track ........................................ 24
Other operations for video playback
(DVD/VCD/SVCD) ................................. 25
Using the Disc Menu ........................... 25
Display the disc information and
current status ........................................ 25
Zooming in ............................................ 26
Resuming playback from the last
stopped point ........................................ 26
Advancing by frame ............................. 26
Changing sound track language......... 26
Changing subtitle language
(DVD only) ............................................ 26
Viewing from another angle
(DVD only) ............................................ 26
Selecting a title (DVD only) ............... 27
Playback Control (PBC) (VCD only) 27
Contents
001-047-LX83-22-Eng 6/9/04, 2:01 PM6
English
7
3139 115 23271
Playing MP3/JPEG/DivX/MPEG-4
disc ............................................................... 28
Playing MP3 music and JPEG
picture simultaneously ........................ 28
Playing Super Audio CD (SACD)........... 29
Special features for picture
disc playback ............................................... 29
Preview Function .................................. 29
Zoom picture ........................................ 29
Playback with multi-angles ................. 29
Scan Effect .............................................. 29
DVD Setup Menu Options
General Setup Menu................................. 30
Locking/ Unlocking the disc
for viewing ............................................. 30
Programming disc tracks (not
for Picture CD/MP3/SACD) ...... 30–31
OSD language ....................................... 31
Screen Saver – turning on/off ........... 31
DivX(R) VOD registration code ....... 31
Audio Setup Menu .................................... 32
Setting the analogue output ............... 32
Speaker Setup ....................................... 32
CD Upsampling .................................... 32
Night mode – turning on/ off ............ 33
Video Setup Menu ..................................... 33
TV Type ................................................... 33
TV Display ............................................. 33
Progressive function-turning on/off . 34
Picture Setting ................................ 34–35
Setting the Video Output ................... 35
Preference Setup Menu ........................... 35
Audio, Subtitle, Disc Menu ................. 35
Restricting playback by Parental
Control ............................................ 35–36
PBC ......................................................... 36
MP3/JPEG Navigator – turning
on/ off ...................................................... 36
Changing the Password....................... 37
Setting the DivX Subtitle .................... 37
Restoring to original settings ............ 37
Tuner Operations
Tuning to radio stations ........................... 38
Presetting radio stations .......................... 38
Using the Plug and Play ....................... 38
Automatic presetting .......................... 39
Manual presetting ................................. 39
Selecting a preset radio station ............. 39
Deleting a preset radio station ......... 39
Sound Controls
Selecting surround sound ........................ 40
Selecting digital sound effects ................. 40
Adjusting the Bass/Treble level .............. 40
Volume Control and Other
Functions
Volume Control ......................................... 41
Switching on/off ........................................ 41
Switching to an active mode.............. 41
Switching to Eco Power standby
mode ....................................................... 41
Using the remote to operate your
‘Philips’ television ...................................... 41
Dimming system’s display screen ........... 42
Setting the Sleep timer ............................ 42
Recording to an external device............ 42
Specifications ...................................... 43
Troubleshooting ......................... 44–45
Glossary ............................................. 46–47
Contents
001-047-LX83-22-Eng1 7/6/04, 10:25 PM7
8
3139 115 23271
English
Supplied accessories
Scart cable (black)
FM wire antenna
MW loop antenna
Remote control
and two batteries
(12nc: 3139 258 70051)
Front/Rear
speaker base
AC power cable
Speaker brackets
and screws
DVD system
cable cover
Care and safety information
Avoid high temperatures, moisture,
water and dust
– Do not expose the system, batteries
or discs to humidity, rain, sand or
excessive heat (caused by heating
equipment or direct sunlight). Always
keep the disc tray closed to avoid getting
dust on the lens.
Avoid condensation problem
– The lens may cloud over when the
player is suddenly moved from cold to
warm surroundings, making it impossible
to play a disc. Leave the player in the
warm environment until the moisture
evaporates.
Do not block the vents
– Do not operate the DVD system/AV
Subwoofer in an enclosed cabinet and allow
about 10 cm (4 inches) of free space all
around the player for adequate ventilation.
10 cm
(4 inches)
10 cm
(4 inches)
10 cm
(4 inches)
DVD Home Cinema System
PHILIPS
Care of disc
– To clean a CD, wipe it in a
straight line from the centre
toward the edge using a soft,
lint-free cloth. Do not use
cleaning agent, as they may
damage the disc.
– Write only on the printed side of a
CD-R/CD-RW and only with a soft felt-
tipped pen.
– Handle the disc by its edge, do not
touch the surface.
Care of the cabinet
– Use a soft cloth slightly moistened
with a mild detergent solution. Do not
use a solution containing alcohol, spirits,
ammonia or abrasives.
Finding a suitable location
– Place the player on a flat, hard, stable
surface.
(4x)
(4x)
General Information
001-047-LX83-22-Eng 6/9/04, 2:01 PM8
English
9
3139 115 23271
1 You can attach the speakers directly to
their bases if you want to place them on
a flat surface.
OR
2 You can choose to hang the speakers
(front and rear only) on the wall. Attach
the supplied bracket firmly to the rear of
speakers using the supplied screws. Then
mount a screw (not supplied) on the wall
where the speaker is to be hung and
hook the speaker securely onto the
mounted screw.
CAUTION!
You should get a qualified person to
attach the brackets to the wall. DO
NOT do it by yourself to avoid
unexpected damage to the
equipment or injury to personnel.
Step 1: Assemble the
speakers
Connections
1
2
Helpful Hints:
– The rear speakers are labelled as REAR L
(left) or REAR R (right).
– The front speakers are labelled as
FRONT L (left) or FRONT R (right).
001-047-LX83-22-Eng 6/9/04, 2:02 PM9
10
3139 115 23271
English
Connections
1 Connect the supplied speakers to the
rear of the AV subwoofer using the fixed
speaker cables by matching the colours of
the jacks and speaker connectors.
2 Connect the AV subwoofer with the
DVD system by plugging in the inter-
connect cable from the AV subwoofer to
the TO AV SUBWOOFER jack at the
rear of the DVD system.
Helpful Hints:
– Ensure that the speaker cables are
correctly connected. Improper connections
may damage the system due to short-circuit.
– To prevent unwanted noise, do not place
the AV subwoofer too close to the DVD
system, AC power adaptor, TV or other
radiation sources.
Step 2: Connecting DVD
system and speakers
to the AV subwoofer
TO AV SUBWOOFER
➠
TO AV SUBWOOFER
Front Speaker
(Right)
Rear Speaker
(Right)
Rear Speaker
(Left)
Centre Speaker
AV Subwoofer
Front Speaker
(Left)
DVD System
1
2
001-047-LX83-22-Eng 6/9/04, 2:23 PM10
English
11
3139 115 23271
Connections
IMPORTANT!
– You only need to make
one video
connection from the following
options, depending on the
capabilities of your TV.
– Connect the DVD system directly
to the TV.
– Scart (RGB) Video provides better
picture quality than S-Video and
Composite Video. These options
must be available on your TV.
Helpful Hint:
– To hear the TV channels through this DVD
system, use the audio cables (white/red - not
supplied) to connect AUX IN jacks to the
corresponding AUDIO OUT jacks on the TV
(not required if you are using Scart
connection).
Step 3: Connecting TV
AUDIO
OUT
S-VIDEO
IN
VIDEO IN
SCART IN
OR
OR
Using Scart jack
● Use the supplied scart video cable (black)
to connect the DVD system’s SCART
jack to the corresponding Scart input
jacks on the TV.
OR
Using S-Video jack
● Use an S-video cable (not supplied) to
connect the DVD system’s S-VIDEO
jack to the S-Video input jack (or labelled
as Y/C or S-VHS) on the TV.
OR
Using Composite Video jack
● Use a composite video cable (yellow -
not supplied) to connect the DVD
system’s VIDEO jack to the video input
jack (or labelled as A/V In, Video In,
Composite or Baseband) on the TV.
001-047-LX83-22-Eng 6/9/04, 2:02 PM11
12
3139 115 23271
English
Connections
IMPORTANT!
– The progressive scan video quality
is only possible when using Y Pb Pr
and a progressive scan TV is required.
– DO NOT connect both SCART
and Y Pb Pr to a TV, it may affect the
picture quality.
Using Component Video jacks
(Y Pb Pr)
1 Use the component video cables (red/
blue/green - not supplied) to connect the
DVD system’s Y Pb Pr jacks to the
corresponding component video input
jacks (or labelled as Y Pb/Cb Pr/Cr or
YUV) on the TV.
2 Change the component video setting
manually to YUV, see page 19.
3 Activate the progressive scan function,
see page 34.
Step 4: Connecting a
Progressive Scan TV
1
1
3
3
4
2
Step 5: Placing the speakers
and AV subwoofer
Front Speaker
(Left)
Front Speaker
(Right)
AV Subwoofer
Rear speaker
(Right)
Rear speaker
(Left)
DVD System
Centre speaker
For best possible surround sound, all the
speakers (except AV subwoofer) should
be placed at the same distance from the
listening position.
1 Place the front left and right speakers at
equal distances from the TV and at an
angle of approximately 45 degrees from
the listening position.
2 Place the centre speaker above the TV so
that the centre channel’s sound is
localised.
3 Place the rear speakers at normal
listening ear level facing each other or
hang on the wall.
4 Place the AV subwoofer on the floor near
the TV.
Helpful Hints:
– To avoid magnetic interference, do not
position the front speakers too close to your
TV.
– Allow adequate ventilation around the
DVD system/AV subwoofer.
001-047-LX83-22-Eng 6/9/04, 2:02 PM12
English
13
3139 115 23271
Connections
1 Connect the supplied MW loop antenna
to the MW jack. Place the MW loop
antenna on a shelf or attach it to a stand
or wall.
2 Connect the supplied FM antenna to the
FM jack. Extend the FM antenna and fix
its ends to the wall.
For better FM stereo reception, connect
an external FM antenna (not supplied).
Helpful Hints:
– Adjust the position of the antennas for
optimal reception.
– Position the antennas as far as possible
from your TV, VCR or other radiation source
to prevent unwanted interference.
After everything is connected
properly, plug the AC power cord
into the power outlet.
The red STANDBY LED on the DVD
system will light up. Never make or
change any connections with the power
switched on.
(optional)
This DVD system comes with a cable
cover, it allows you to organise all the
connecting cables neatly through the
opening and you can use the velcro strip
that attached to the inter-connect cable
to tie up rest of the cables together.
TO AV SUBWOOFER
TO AV SUBWOOFER
➠
Helpful Hint:
– Refer to the type plate on the rear of the
AV subwoofer for identification and supply
ratings.
1
2
➠
MW
antenna
fix the claw
into the slot
Step 7: Connecting the
power cord
TO AV SUBWOOFER
AUDIO
OUT
S-VIDEO
IN
VIDEO IN
SCART IN
~ AC MAINS
Step 6: Connecting FM/MW
antennas
FM
antenna
DVD system
AV Subwoofer
AV Inter-connect cable
001-047-LX83-22-Eng 6/9/04, 2:02 PM13
14
3139 115 23271
English
Viewing and listening to the
playback
1 Connect the VCR or Cable/Satellite Box
to the TV as shown.
2 Connect the DVD system’s AUX IN
(R/L) jacks to the AUDIO OUT jacks on
the VCR or cable/satellite box.
Before starting operation, press
SOURCE to select “AUX” in order to
activate the input source.
Connections (Optional)
Connecting a VCR or
Cable/Satellite Box
TO AV SUBWOOFER
AUDIO
OUT
S-VIDEO
IN
VIDEO IN
SCART IN
2
4
1
~ AC MAINS
3
VCR or Cable/
Satellite Box
Using the VCR for recording DVD
playback
Some DVDs are copy-protected. You
cannot record or dub protected discs
using a VCR.
3 Connect the DVD system’s S-VIDEO
jack to the S-VIDEO IN jack on the VCR.
4 Connect the DVD system’s LINE OUT
(R/L) jacks to the AUDIO IN jacks on
the VCR.
This will allow you to make analogue
stereo (two channel, right and left)
recordings.
To view DVD playback while
recording,
you must connect the DVD system to
your TV using SCART (as shown above)
connection.
001-047-LX83-22-Eng 6/9/04, 2:02 PM14
English
15
3139 115 23271
Listening to the playback
● Connect the DVD system’s DIGITAL
IN jack to the DIGITAL OUT jack on a
digital audio device.
Before starting operation, press
SOURCE to select “DIGI IN” in order
to activate the input source.
Helpful Hints:
– Some DVDs are copy-protected. You
cannot record the disc through a VCR or
digital recording device.
– You cannot hear or record the SACD or
MP3-CD playback if you use the digital
connection.
– For your playback through DIGITAL IN
connection, set the digital output of that
player to PCM format.
– Always refer to the owner’s manual of the
other equipment for complete connection
and use details.
Connecting digital audio
equipment
(for example)
CD Recorder
TO AV SUBWOOFER
Connections (Optional)
001-047-LX83-22-Eng 6/9/04, 2:02 PM15
16
3139 115 23271
English
Functional Overview
Remote control
^
%
$
#
@
!
0
9
3
4
5
6
7
8
1
2
•
≥
§
∞
≤
£
™
¡
)
(
*
&
ª
* = Press and hold the button for more than two seconds.
1 SOURCE
– Selects the relevant active source mode:
DISC, TUNER (FM/MW), TV or AUX/DI.
2 DISPLAY
– Displays the current status or disc
information.
3 PROGRAM
– DISC: starts programming.
– TUNER: starts *automatic/ manual preset
programming.
4 SYSTEM MENU
– Enters or exits system setup menu.
5 Cursor
– Selects movement direction in the menu.
– TUNER: press left or right to select a
preset radio station.
– TUNER: up or down to select auto
tuning.
6 OK
– Confirms a selection.
7 S / T
– DISC: *searches backward/forward or
selects a track.
– TV: selects previous/next channel (Philips
TV only).
– TUNER: tunes the radio frequency up/
down.
8 Ç
– Exits an operation.
– DISC: stops playback.
– DISC: holding down the button will open
and close the disc tray.
– TUNER: *erases a preset radio station.
9 MUTE
– Mutes or restores the volume.
0 VOL +-
– Adjusts the volume level.
001-047-LX83-22-Eng 6/9/04, 2:02 PM16
English
17
3139 115 23271
Functional Overview
* = Press and hold the button for more than two seconds.
! ANGLE
– Select a DVD disc camera angle (if
available).
@ SUBTITLE
– Selects a subtitle language.
# REPEAT
– Selects various repeat modes.
$ SURR
– Selects multichannel surround or stereo
mode.
% REPEAT A-B
– Repeats a specific section on a disc.
^ SOUND
– Selects a sound effect.
& NIGHT (in DVD mode only)
– Optimises the dynamics of the sound
output.
* CD UP SAMP.
– Converts music CD to a higher sampling
rate for better sound quality.
( BASS/TREBLE
– Selects BASS (low tone) or TREBLE (high
tone) sound mode and use the VOLUME
control to change the tone level.
) AUDIO
– Selects an audio language (DVD) or an
audio channel (CD).
¡ ZOOM
– Enlarges a picture on the TV screen.
™ TV VOL +-
– Adjusts TV volume (Philips TV only).
£ É
– DISC: starts playback.
≤ Å
– DISC: pauses playback.
∞ DISC MENU
– Enters or exits disc contents menu.
– For VCD version 2.0 only;
In stop mode, turns on/off playback
control (PBC) mode.
During playback, returns to main menu.
§ RETURN/TITLE
– To go back to previous menu.
– Displays the disc’s Title menu (if available).
≥ Numeric Keypad (0-9)
– Enters a track/title number of the disc.
– Enters a number of a preset radio station.
• DIM
– Selects different levels of brightness for
display panel.
– *Sets the sleep timer function.
ª B
– Switches to Eco Power standby mode.
001-047-LX83-22-Eng 6/9/04, 2:02 PM17
18
3139 115 23271
English
Functional Overview
* = Press and hold the button for more than two seconds.
1 STANDBY ON (B)
– Switches to Eco Power standby mode or
turns on the system.
2 OPEN/CLOSE 0
– Opens/Closes the disc tray.
3 ÉÅ PLAY/PAUSE
– DISC: starts/pauses playback.
– TUNER: starts preset radio station
installation in Plug & Play mode.
4 S PREV / NEXT T
– DISC: *searches backward/forward or
selects a track.
– TV: selects previous/next channel (Philips
TV only).
– TUNER: tunes the radio frequency up/
down.
5 Ç STOP
– Exits an operation.
– DISC: stops playback.
– TUNER: *erases a preset radio station.
1
#
2
4
!
3
7
6
5
@
9
8
0
Top and front panel
6
SOUND
– Selects a sound effect.
7 SOURCE
– Selects the relevant active source mode:
DISC, TUNER (FM/MW), TV or AUX/DI.
8 VOLUME
– Adjusts the volume level.
9 System display panel
0 SACD indicator
– Lights up when playing Super Audio CD.
! iR
– Point the remote control towards this
sensor.
@ STANDBY ON indicator
– Lights up when in Eco Power standby
mode.
# Disc tray
001-047-LX83-22-Eng 6/9/04, 2:02 PM18
English
19
3139 115 23271
Getting Started
Step 1: Inserting batteries into
the remote control
1 Open the battery compartment.
2 Insert two batteries type R06 or AA,
following the indications (+-) inside
the compartment.
3 Close the cover.
Using the remote control to operate
the system
1 Aim the remote control
directly at the remote
sensor (iR) on the front
panel.
2 Press SOURCE button
on the remote to select
the mode you wish to
control (for example TV,
DISC). The selected
source mode will light
up on the LED panel for
a few seconds.
3 Then select the desired
function (for example
É,
S,
T).
CAUTION!
– Remove batteries if they are
exhausted or if the remote is not to
be used for a long time.
– Do not use old and new or
different types of batteries in
combination.
– Batteries contain chemical
substances, so they should be
disposed of properly.
Step 2: Setting the TV
IMPORTANT!
Make sure you have completed all
the necessary connections. (See
page 11 “Connecting TV”)
1 Press SOURCE control until “DISC”
appears on the display panel.
2 Turn on the TV and set to the correct
video-in channel. You should see the blue
DVD background screen on the TV.
➜ Usually this channel is between the
lowest and highest channels and may be
called FRONT, A/V IN, VIDEO. See your
TV manual for more details.
➜ Or, you may go to channel 1 on your
TV, then press the Channel down button
repeatedly until you see the Video In
channel.
➜ Or, the TV remote control may have a
button or switch that chooses different
video modes.
Switching to YUV/RGB video output
setting
If the TV shows a blank screen or
distorted picture, it may be due to the
DVD system’s component video setting
does not match with the video
connection. You can change the
component video setting between YUV
and RGB as below:
1 Press STANDBY ON on the front
panel to switch on the DVD system.
2 Press OPEN/CLOSE 0 on the top
panel to open the disc tray.
3 Press 2 on the remote.
4 Press MUTE on the remote.
➜ You should see the blue DVD
background screen on the TV.
001-047-LX83-22-Eng 6/9/04, 2:02 PM19
20
3139 115 23271
English
Getting Started
Selecting the colour system that
corresponds to your TV
In order for a DVD to play on this DVD
system, the colour system of the DVD,
the TV and the DVD player should match.
Before changing the TV system, determine
the colour system of your TV.
1 In disc mode, press SYSTEM MENU.
2 Press 2 repeatedly to select {VIDEO
SETUP PAGE}.
3 Press 34 to highlight {TV TYPE}, then
press 2.
4 Press 34 to highlight one of the options
below:
PAL – Select this if the connected TV has
the PAL colour system. It will change the
video signal of an NTSC disc and output it
to PAL format.
NTSC – Select this if the connected TV
has the NTSC colour system. It will
change the video signal of a PAL disc and
output it to NTSC format.
MULTI – Select this if the connected TV
is compatible with both NTSC and PAL
(multi-system). The output format will be
in accordance with the video signal of the
disc.
5 Select a setting and press OK.
➜ Follow the instructions shown on the
TV to confirm the selection (if any).
➜ If a blank/distorted TV screen appears,
wait for 15 seconds for auto recovery.
Setting the TV Display
Set the aspect ratio of the DVD Player
according to the TV you have connected.
The format you select must be available
on the disc. If it is not, the setting for TV
display will not affect the picture during
playback.
1 In disc mode, press SYSTEM MENU.
2 Press 2 repeatedly to select {VIDEO
SETUP PAGE}.
3 Press 34 to highlight {TV DISPLAY}, then
press 2.
4 Press 34 to highlight one of the options
below:
4:3 PAN SCAN – Select this if you have
a conventional TV and want both sides of
the picture to be trimmed or formatted
to fit your TV screen.
4:3 LETTER BOX – Select this if you
have a conventional TV. In this case, a
wide picture with black bands on the
upper and lower portions of the TV
screen will be displayed.
16:9 – Select this if you have a wide-
screen TV.
5 Select a setting and press OK.
TIPS:
To return to the previous menu, press 1.
To remove the menu, press SYSTEM MENU.
001-047-LX83-22-Eng 6/9/04, 2:02 PM20
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51

Philips LX8300SA User manual

Philips
Brand
Philips
Model
LX8300SA
Category
Home cinema systems
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents