Owner’s Manual
Model No. TS1001
10” TABLE SAW
QUESTION...
1•877•393•7121
11-0423
You will need this manual for safety instructions, operating procedures, and warranty.
Put it and the original sales invoice in a safe, dry place for future reference.
Visit us on the web at www.southerntechllc.com
Horsepower (Peak HP) . . . . . . . . . . . . . . . . . . . . 2-1/2 HP
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,000
Blade . . . . . . . . . . . . . . . . . 10”-36T Carbide Tipped Blade
Table dimensions . . . . . . . . . . . . . . . . . . . . . . . . 26” x 19”
Table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 45°
Maximum Depth of Cut at 90˚ . . . . . . . . . . . . . . . . . . . . .3”
Maximum Depth of Cut at 45˚ . . . . . . . . . . . . . . . . . . . 2.5”
Maximum Depth of Dado . . . . . . . . . . . . . . . . . . . . . . . 1/2”
TABLE OF CONTENTS
PRODUCTION
SPECIFICATIONS
SAFETY RULES 1
Work Preparation
Work Area Preparation
Tool Maintenance
Tool Preparation
ASSEMBLY 2
Unpackaging
Tool Needed
Mount Table Saw
Install the Bracket for the Push Stick
Raise and Lower the Saw Blade
Tilt Saw Blade
Rip Fence
Install and Change the Blade
Blade Guard Assembly
Adjust the saw Blade Guard
Adjust Cutting Angle
Adjust Blade Parallel to the Miter Gauge Slot
Grounding Instructions
Extension Cords
OPERATION 6
Safety Precautions
On/Off Switch
Overload Protection
Ripping
Bevel Ripping
Crosscutting 90˚ Miter Gauge
Bevel Crosscutting: 0˚ ~ 45˚ Bevel and 90˚ Miter
Angle
Compound Miter Crosscutting: 0˚ ~ 45˚ Blade Bevel
and 0˚ ~ 45˚ Miter Gauge
0˚ ~ 45˚ Miter Angle
MAINTENANCE 9
Cleaning
Lubrication
Keep Tool in Repair
TROUBLESHOOTING 10
PARTS ILLUSTRATION & 12
LIST
WARRANTY 14
SECTION PAGE
SAFETY RULES
1
Some dust created by power sanding, sawing, grinding,
drilling and other construction activities contains chemicals
known to cause cancer, birth defects or other reproductive
harm.
Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other
masonry products.
• Arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area and work
with approved safety equipment. Always wear OSHA/
NIOSH approved, properly fitting face mask or respirator
when using such tools.
For your own safety, read all of the rules and precautions
before operating tool.
Always follow proper operating procedures as defined
in this manual even if you are familiar with use of this or
similar tools. Remember that being careless for even a
fraction of a second can result in severe personal injury.
WORK PREPARATION
• Wear proper apparel. Do not wear loose clothing,
gloves, neckties, rings, bracelets or other jewelry which
may get caught in moving parts of the tool.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States
ANSI Z87.1. Everyday glasses have only impact
resistant lenses. They are NOT safety glasses.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools
when tired, intoxicated or when taking medications that
cause drowsiness.
WORK AREA PREPARATION
• Keep work area clean. Cluttered work areas invite
accidents.
• Do not use power tools in dangerous environments. Do
not use power tools in damp or wet locations. Do not
expose power tools to rain.
• Work area should be properly lighted.
• Proper electrical receptacle should be available for tool.
Three-prong plug should be plugged directly into
properly grounded, three-prong receptacle.
• Extension cords should have a grounding prong and
the three wires of the extension cord should be of the
correct gauge.
• Keep visitors at a safe distance from work area.
• Keep children out of the work area. Ensure your work
shop is child-proof. Use padlocks, master switches or
remove switch keys to prevent any unintentional use of
power tools.
TOOL MAINTENANCE
• Always unplug tool prior to inspection.
• Consult manual for specific maintaining and adjusting
procedures.
• Keep tool lubricated and clean for a safe operation.
• Remove adjusting tools. Form habit of checking to see
that adjusting tools or accessories are removed before
switching tool on.
• Keep all parts in working order. Check to determine that
guard or other parts will operate properly and perform
their intended function.
• Check for damaged parts. Check for alignment of
moving parts, binding, breakage, mounting and any
other condition that may affect tool’s operation.
• A guard or any other part that is damaged should be
properly repaired or replaced. Do not perform makeshift
repairs.
TOOL OPERATION
• Use the right tool for your job. Do not force your
tool or attachment to do a job for which it was not
designed.
• Disconnect tool when changing sanding sheets/belts.
• Avoid accidental start-up. Make sure that the tool is in
the “OFF” position before plugging in.
• Do not force tool. It will work most efficiently at the rate
for which it was designed. Keep hands away from
moving parts and sanding surfaces.
• Never leave tool running unattended. Turn the power off
and do not leave tool until it comes to a complete stop.
• Do not overreach. Keep proper footing and balance.
• Never stand on tool. Serious injury could occur if tool is
tipped or if sanding surface is unintentionally contacted.
• Know your tool. Learn the tool’s operation, application
and specific limitations before using it.
• Use recommended accessories. Use of improper
accessories may cause risk of injury to persons.
• Handle workpiece correctly. Protect hands from possible
injury.
• Turn tool off if it jams. The motor may jam if too much
pressure is applied on the sanding surface.
• Support workpiece with mitre gauge, belt platen or work
table.
• Maintain 1/16” (1.5 mm) maximum clearance between
table and sanding belt or disc.
CAUTION: Think safety! Safety is a combination of opera-
tor common sense and alertness at all times when tool is
being used.
Do not attempt to operate tool until it is completely
assembled according to the instructions.
WARNING
WARNING
WARNING
UNPACKING
Check for shipping damage. If damage has occurred, a
claim must be filled with carrier. Check for completeness.
Immediately report missing parts to dealer.
Your table saw is shipped complete in one container.
Carefully unpack the table saw and all loose items from
the shipping container. Figure 1, illustrates the table saw
and all loose parts.
ITEM DESCRIPTION QUANTITY
A Saw Assembly 1
B Plug Clip 1
C Rip Fence/Push Stick Storage Clips 2
D Hand Wheel Grip 1
E Guard/Splitter Assembly 1
F Open-end Wrench 1
G Open-end Wrench 1
H Push Stick 1
I Rip Fence 1
J Mitre Gauge Assembly 1
ASSEMBLY
2
Figure 1
A
B
C
D
E
F
H
G
J
I
3
ASSEMBLY
CAUTION: Do not attempt assembly if parts are missing.
Use this manual to order replacement parts.
Do not operate this tool until completely assembled. Do
not operate this tool until you have completely read
and understood this manual.
MOUNT TABLE SAW
Refer to figure 2
• The table saw must be installed in a well-lighted area
with correct power supply.
• The table saw can be installed on either a workbench or
a tool stand by using bolts, lock washers, and hex nuts.
• The table saw must be bolted to a firm and level surface.
• There must be enough clearance for the moving
workpiece during operation and enough room for safety
operation of the machine.
Figure 2 shows the base dimension and mounting holes.
Figure 2
INSTALL THE BRACKET FOR THE PUSH
STICK
Refer to Figure 3
Secure the two brackets to the right-hand side of the saw
using the Phillips screw supplied.
Figure 3
RAISE AND LOWER THE SAW BLADE
Refer to Figure 4
1. Screw the crank handle into the hand wheel.
2. Turn the hand wheel clockwise to lower the blade and
turn the hand wheel counterclockwise to raise the blade.
Figure 4
TILT SAW BLADE
Refer to Figure 5
1. Loosen blade miter angle lock knob to tilt the saw
blade.
2. Slide the hand wheel without turning it until the blade is
at the desired angle.
3. Tighten the miter angle lock knob.
Figure 5
RIP FENCE
Refer to figure 6
1. Position the fence on the saw table.
2. Hook the rear steel clamp plate of fence over the back
edge of saw table.
3. Engage the lock head into the front groove of saw table.
Figure 6
4. Lift the fence lock hand and slide the fence to the
desired position. The rip fence is usually operated on
the right hand side of the table.
5. Push down the lock hand to secure the fence position.
6. Rotate knob clockwise to increase fence tension on the
saw table if necessary.
WARNING
Figure 3
Rear Steel Clamp
Lock Head
Brackets
Fence Handle
Miter Angle Lock Knob
Hand WheelCrank Handle
INSTALL AND CHANGE THE BLADE
Refer to Figure 7, 8 and 9
Turn the switch to OFF position and disconnect the ma-
chine from power source.
CAUTION: Wear gloves while installing and removing the
saw blade
1. Remove the table insert.
2. Raise the blade arbor to the maximum height by turning
the blade elevation control wheel counter-clockwise.
Figure 7
3. Remove the arbor nut and flange.
4. Install the saw blade onto the arbor with the blade teeth
pointing toward the fornt of the saw.
5. Install the flange against the blade and thread the arbor
nut as far as possible by hand. Ensure that the blade is
flush against the inner blade flange.
Figure 8
Figure 9
6. To tighten the arbor nut, use the open end wrench and
align the wrench jaws on the flats of the flange to keep
the arbor from turning.
7. Place the box and wrench on the arbor nut, and turn
clockwise (to the rear of the table saw).
8. Lightly insert the rear part of the table insert into table,
and pull down its front part in table recess to lock.
BLADE GUARD ASSEMBLY
Refer to Figure 10
Turn the switch to OFF position and disconnect the
machine from power source.
POSITION THE RIVING KNIFE
1. Remove the table insert.
2. Set the blade to the maximum height and the tilt to zero
degrees on the bevel scale.
3. Rotate the riving knife release lever clockwise, so that it
points upward.
4. Pull riving knife towards release lever to disengage it
from the pins.
5. Slide the riving knife up to its highest position, so that it
is directly over the center of the blade.
6. Align holes in riving knife with pins and lock the release
lever by rotating it counterclockwise. Push/Pull riving
knife to verify that it is locked in place.
7. Replace table insert.
Figure 10
Figure 11
BLADE GUARD INSTALLATION
Blade guard installation
1. Hold the front of the barrier guard assembly by the
metal “fork” with one hand. Hold the guard release
lever up with the other hand.
2. Lower the rear of guard assembly and slip the cross
bar into the rear notch on top of the riving knife.
3. Lower the front of the guard assembly until the metal
“fork” is parallel with the table.
4. Press down on the guard release lever until you feel
and hear it snap into the locking position. Check that
the guard assembly is securely connected.
4
ASSEMBLY
WARNING
WARNING
Blade Arbor
Arbor Nut
Blade Flange
Riving Knife
Open-end
Blade Wrench
Saw Blade
Screws
Release Lever
Release Lever
Riving Knife
Pin
5
ASSEMBLY
Figure 10
Figure 12
ANTI-KICKBACK DEVICE INSTALLATION
Refer to Figure 13
Installation of anti-kickback device and blade guard are
independent of each other. The anti-kickback device can
be attached before the blade guard.
1. While pulling out the attachment pin, attach the
anti-kickback device into the flat recessed area “A” of
the riving knife.
2. Slide the anti-kickback device down until it drops into
the recessed area – then release the attachment pin
such that the anti-kickback device locks onto the riving
knife immediately behind the guard assembly. Check
that the attachment pin is securely connected into
locking hole.
3. Raise and lower the pawls when letting go, the
sprint-loaded pawls must come down and contact the
table insert.
Figure 13
ADJUST CUTTING ANGLE
Refer to Figure 14
1. Check the angle of the saw blade relative to the angle
adjustment scale on the saw table in order to operate a
clear perpendicular 90°cut.
2. Raise the blade to the maximum height using the hand
wheel.
Figure 14
3. Set an angle of 90°on the saw blade between the teeth.
Turn the hand wheel until the saw blade is against the
vertical angle stop.
4. The pointer should be at zero position. If not, loosen
the Phillips screw and set the pointer to zero.
5. Test to check the precise angle cut. If not, repeat the
above steps to adjust it.
ADJUST BLADE PARALLEL TO THE MITRE
GAUGE SLOT
Refer to Figure 15
Turn the switch to OFF position and disconnect the
machine from power source.
1. Remove the table insert.
2. Set the blade to the maximum height and the tilt to zero
degrees on the bevel scale. Lock the blade bevel lock.
3. Reassemble splitter. Loosen splitter by lifting handle.
4. Raise splitter until the two lowest holes are in the pins.
Pull down handle to tighten splitter. Shake splitter to
check if well tightened. If not, repeat above process.
5. Install the anti-kickback pawl. Pull out the knob, and
aligning splitter, release the pin and make sure it is in
the hole.
6. Lift metal board off the blade guard, and push the blade
guard into the notch of the splitter. Lightly pull down
the front part of the blade guard into the splitter, and
push the metal board down to lock,.
7. Remove the combination square and stand the saw
on its left side, so that you can access the six
adjustment nuts that secure the axis rod to the table.
Make sure the table is secure.
8. Use a 10mm wrench to loosen all six adjustment nuts
about a half a turn each. Place the saw in the upright
position. Move the blade carefully to the left or the
right, until it is aligned, checking alignment with the
combination square.
WARNING
Riving Knife
Guard
Release Lever
Cross Bar
Rear Notch
Blade Guard
Assembly
Pin
9. Tighten the two front and four rear adjustment nuts.
Reach under the front and rear of table with a wrench
to access these nuts. Re-check the alignment. If ad
ditional adjustments are necessary, loosen only the
front two adjustment nuts, and repeat the above steps
until the blade is parallel to the mitre gauge slot.
10. Tighten two front adjustment nuts, then stand the saw
on its left side, and tighten the four rear adjustment
nuts. Place the saw upright and re-check the alignment
to make sure the blade is parallel to the mitre gauge slot.
Figure 15
GROUNDING INSTRUCTIONS
Improper connection of equipment grounding conductor
can result in the risk of electrical shock. Equipment should
be grounded while in use to protect operator from electri-
cal shock.
• Check with a qualified electrician if you do not
understand grounding instructions or if you are in
doubt as to whether the tool is properly grounded.
• This tool is equipped with an approved cord rated at
150V and a 3-prong grounding type plug (see Figure
14) for your protection against shock hazards.
• Grounding plug should be plugged directly into a
properly installed and grounded 3-prong grounding type
receptacle, as shown (see Figure 16).
Figure 16 3-Prong Receptacle
• Do not remove or alter grounding prong in any manner.
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electrical shock.
Do not permit fingers to touch the terminals of plug when
installing or removing from outlet.
• Plug must be plugged into matching outlet that is
properly installed and grounded in accordance with all
local codes and ordinances. Do not modify plug
provided. If it will not fit in outlet, have proper outlet
installed by a qualified electrician.
• Inspect tool cords periodically, and if damaged, have
repaired by an authorized service facility.
• Green (or green and yellow) conductor in cord is the
grounding wire. If repair or replacement of the electric
cord or plug is necessary, do not connect the green (or
green and yellow) wire to a live terminal.
• A 2-prong wall receptacle must be replaced with a
properly grounded 3-prong receptacle installed in
accordance with National Electric Code and local codes
and ordinances.
EXTENSION CORDS
• The use of any extension cord will cause some drop in
voltage and loss of power.
• Wires of the extension cord must be of sufficient size to
carry the current and maintain adequate voltage.
• The minimum extension cord wire size is A.W.G. 14.
Do not use extension cords over 25 feet long.
• Use only 3-wire extension cords having 3-prong
grounding type plugs and 3-pole receptacles which
accept the tool plug.
• If the extension cord is worn, cut or damaged in any
way, replace it immediately.
MOTOR
Table Saw is supplied with a 2-1/2 HP motor installed.
The 120 Volt AC universal motor has the following
specifications:
Horsepower (Peak HP) . . . . . . . . . . . . . . . . . . . . .2-1/2 HP
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
Amperes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Hertz. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5,000
WARNING
WARNING
Ruler
Gauge Slot
Combination Square
Ruler
OPERATION
7
For your own safety, read the operating manual and
all the safety instructions before using the table saw.
• The failure to follow the general safety rules and
safety precautions can greatly increase the
likelihood of injury.
SAFETY PRECAUTIONS
• Be aware of general power tool safety. Make sure all
the safety rules are understood.
• Disconnect the machine from power source whenever
adjusting or replacing any parts.
• Do not plug in unless switch is in “OFF” position.
• Keep hands away from all moving parts.
• Ware eye protection or face shield during operation.
• Make sure all guards are attached and securely
fastened. Keep saw and blade guards in proper
working condition.
• Make sure all the mobile parts move freely and are free
from interference.
• Keep blades shaft, aligned and properly attached.
• Secure blade is tightened to the arbor before turning on
the machine.
• Make sure the bevel angle lock knob is tightened.
• Make sure the fence is locked and is parallel to the
miter gauge groove.
• Never turn the machine “ON” with the workpiece
contacting the blade.
• Do not force cut. Slowing or stalling will overheat motor.
• Do not perform a workpiece that is warped, contains
knobs, or is embedded with foreign objects (nails,
staples, etc) to prevent kickback.
• Do not allow anyone to stand or cross in line of blade
rotation.
• Keep table saw maintained. Follow maintenance in
structions.
ON/OFF SWITCH
Refer to Figure 17
The ON/OFF switch is located on the front of table saw.
To turn the machine ON, pull the switch to the up position.
To turn the machine OFF, push the switch to the down
position.
NOTE: When the machine is not in use, the machine
should be locked in the “OFF” position to prevent unau-
thorized use.
• To lock the machine, turn the switch to “OFF” position.
• Pull the key out. The switch cannot be turned on with
out the key.
• If the key is removed when the switch is at the “ON”
position, the switch can be turned off but cannot be
turned on again.
• To unlock, place the key into the slot on switch unit until
it snaps.
Figure 17
OVERLOAD PROTECTION
Refer to Figure 18
• The table saw has an overload protection installed next
to the main power switch. The overload protection
protects the motor unit by shutting off the power supply
when excessive electric current is detected. If the
overload protection is tripped, the table saw will not
power on.
• Before reset of overload protection, check motor,
switch and line connection for short circuit or faulty
components.
• To reset the overload protection, turn the switch to
“OFF” position. Then press the overload protection
button next to the main switch.
Figure 18
RIPPING
Refer to Figure 19 and 20
CAUTIONS:
Before operating the saw, check the following:
• The blade is tightened on the arbor.
• The miter angle lock knob is tightened.
• The fence is locked into position and is parallel to the
miter slots.
• The blade guard is in place and work properly.
• Safety glasses are on. The blade guard must always
be used to prevent kickback.
Overload Protection
OPERATION
6
WARNING
8
OPERATION
• Lift up fence lock handle to move the rip fence.
• Slide the fence to the desred cutting width and push
down the fence lock handle to lock the fence.
• Ride one edge of workpiece against the rip fence while
the flat side of the workpiece rests on the table. The
workpiece must have a straight edge to be pushed
along the fence and make the workpiece a solid contact
with the table.
• Raise the saw blade to approximate 1/8” above the
workpiece.
• Turn on switch and wait until the saw blade has
reached its maximum speed.
• Never stand in line of the saw cut while ripping.
• Hold the workpiece with both hands and push it along
the fence into the saw blade.
Figure 19
• While the workpiece is fully on the table, it can be fed
through the saw blade with one hand.
• Do not touch the cut-off stock on the table with the
hands until the saw blade is stopped.
• If ripping the workpiece less than 4 inches wide, a
push stick should always be used to complete the feed.
Never pull the workpiece in the opposite direction of feed.
Never perform a back cut during the operation. If you do
not want to cut completely through the workpiece, turn off
the machine and wait until the saw blade has reached a
complete stop to remove the workpiece.
Figure 20
BEVEL RIPPING
The cut is the same as ripping except the blade bevel
angle is set to an angle other than 0 degree.
CROSSCUTTING 90° MITER GAUGE
Refer to Figure 21
1. Crosscutting is cutting either across the width or across
the grain of the workpiece.
CAUTIONS: Never use a rip fence and miter gauge at the
same time.
2. Raise the saw blade to approx.1/8” above the
workpiece.
3. Place the workpiece against the miter gauge with the
blade path in line with the desired cut location. Move
the workpiece to one inch distance from the blade.
4. Turn on the saw and wait for the blade to run at the full
speed.
5. Never stand in line of the saw blade path. Always stand
to the side of the blade.
6. Keep the workpiece against the miter gauge. Slowly
push the workpiece through the saw blade.
Figure 21
BEVEL CROSSCUTTING
0° ~ 45° BEVEL AND 90° MITER ANGLE
Refer to Figure 22
1. Adjust the blade to the desired angle and tighten the
miter angle lock knob.
2. Tighten miter lock handle.
3. Hold the workpiece against the miter gauge throughout
the cutting operation.
Figure 22
WARNING
Push Stick
COMPOUND MITER CROSSCUTTING
0° ~ 45° BLADE BEVEL AND 0° ~ 45° MITER
GAUGE
Refer to Figure 23
1. Place the miter gauge at the right side goove of the
table and set it to the desired angle.
2. Set the blade to the desired bevel angle and tighten
miter angle lock knob.
3. Hold the workpiece against the miter gauge through the
operation.
Figure 23
0° ~ 45° MITER ANGLE
Refer to Figure 24
1. Set the blade to 0° and tighten the miter angle lock
knob. Set the miter gauge to the desired angle.
2. Holding the workpiece against the miter gauge
throughout the operation.
Figure 24
DADO CUTS
1. A Dado table insert is included with this saw. Remove
the saw blade and blade guard. Install a Dado blade
and the Dado table insert.
2. Instructions for operating are packed with the
separately purchased Dado set.
3. The arbor on this saw restricts the maximum width of
the cut to 1/2” (13mm).
4. Make sure that the Dado nut is tight, and that at least
one thread of the arbor sticks out past the nut.
5. You must remove the blade guard and splitter when
using the Dado. Excuse caution while the Dado
is operating.
6. Check the saw to make sure the Dado will not strike the
housing, inert, or motor while in operation.
NOTE: When using the Dado blade nut slot, the Dado nut
must be used.
WARNING: FOR YOUR OWN SAFETY, ALWAYS
REPLACE THE BLADE, BLADE GUARDS ASSEMBLY,
AND BLADE INSERT WHEN YOU ARE FINISHED
Disconnect the unit from power source before serving or
disassembling any components.
CLEANING
• Keep machine and workplace clean. Avoid accumulation
of sawdust on the tool.
• Be certain motor is kept clean and free of dust.
• Use soap and water to clean painted parts, rubber parts
and plastic guards.
LUBRICATION
• All motor bearings are permanently. Lubricate at the
factory and require no additional lubrication.
• On all mechanical parts of your table saw where a pivot
or threaded rods are present, lubricate using graphite
or silicone. These dry lubricants will not hold sawdust as
would oil or grease.
KEEP TOOL IN REPAIR
• If power cord is worn, cut, or damaged in any way, do
not operate the machine.
• Replace any worn, damaged, or missing parts. Use
parts list to order parts. Any attempt to repair motor
may create a hazard unless repair is done by a qualified
service technician.
WARNING
MAINTENANCE
9
TROUBLESHOOTING
10
SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION
Motor will not start 1. Low voltage
2. Short circuit in line cord or plug
3. Short circuit in motor
4. Open circuit or loose connection in
motor
5. Incorrect fuses or circuit breakers
6. Defective switch
7. Defective capacitor
8. Motor overload results in circuit
breaker tripped
1. Check power supply for proper voltage
2. Inspect line cord and plug for faulty insulation or
shorted connection
3. Inspect connection on motor.
4. Inspect connection on motor
5. Replace with correct fuses or circuit breakers
6. Replace switch
7. Replace capacitor
8. Turn the machine off and reset overload protec-
tion.
Motor stalls or fails to
reach full speed
1. Power overload
2. Low voltage from power supply
3. Undersized line cord
4. Motor overload
5. Short circuit or loose connection in
motor
6. Incorrect fuses or circuit breakers
7. Wood chips clogged
1. Reduce workload on the power supply
2. Check power supply for proper voltage
3. Use line cord of adequate size or reduce length
of wiring
4. Reduce load on motor
5. Inspect the connection in motor for loose or
shorted connection
6. Replace with correct fuses or circuit breakers
7. Inspect chip blower assembly and fan belt. Re-
move excessive wood chips
Motor overheats 1. Motor overloaded
2. Excessive dust build-up results in
decreased air circulation
1. Reduce load on motor. Turn off the machine
until motor cools down
2. Remove dust build-up
Frequent tripping of
circuit breaker
1. Motor overload
2. Inadequate capacity of circuit
breaker
3. Circuit overload
4. Blades are dull
1. Reduce load on motor
2. Replace with correct circuit breaker
3. Reduce circuit load
4. Sharpen or replace blades
SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION
Does not make
accurate 45°and 90°
rip cuts
1. Positive stop not adjusted
correctly.
2. Tilt angle pointer not set
accurately.
1. Check blade with square and
adjust positive stop.
2. Check blade with square and
adjust to zero.
Material pinched
blade when ripping
1. Rip fence not aligned with blade.
2. Warped wood, edge against
fence is not straight.
1. Check and adjust rip fence.
2. Select another piece of wood.
Material binds on
splitter
Splitter not aligned correctly with
blade.
Check and align splitter with blade
Saw makes
unsatisfactory cuts
1. Dull blade.
2. Blade mounted backwards.
3. Gum or pitch on blade.
4. Incorrect blade for work being
done,
5. Gum or pitch on table causing
erratic feed.
1. Replace blade.
2. Turn the blade around.
3. Remove blade and clean with
turpentine and coarse steel wool.
4. Change the blade.
5. Clean table with turpentine and
steel wool.
Material kicked back
from blade
1. Rip fence out of adjustment.
2. Splitter not aligned with blade.
3. Feeding stock without rip fence.
4. Splitter not in place.
5. Dull blade.
6. The operator letting go of mate-
rial before it is past saw blade.
7. Miter angle lock knob is not tight.
1. Align rip fence with miter gauge slot.
2. Align splitter with blade.
3. Install and use rip fence.
4. Install and use splitter.(with guard)
5. Replace blade.
6. Push material all the way past saw
blade before releasing work.
7. Tighten knob.
Blade does not raise
or tilt freely.
Sawdust and dirt in elevation/
tilting mechanisms
Brush or blow out loose dust and dirt.
Blade does not come
up to speed. Reset
trips too easily
1. Extension cord too light or too long.
2. Low house voltage.
1. Replace with adequate size cord.
2. Contact your electric company.
Saw vibrates
excessively
1. Saw not mounted securely to
workbench.
2. Bench on uneven floor.
3. Damaged saw blade.
1. Tighten all mounting hardware.
2. Reposition on flat level surface.
3. Replace blade.
Does not make
accurate 45°and 90°
crosscuts
Miter gauge out of adjustment. Adjust mitre gauge.
TROUBLESHOOTING
11
10” TABLE SAW PARTS ILLUSTRATION
12
1 TS1001001 Screw, GB845-85 ST4.2x12 20
2 TS1001002 Rear Cover 1
3 TS1001003 Brush Holder 2
4 TS1001004 Carbon Brush 2
5 TS1001005 Motor Housing 1
6 TS1001006 Screw, GB70-85 M5x30 3
7 TS1001007 Spring Washer, GB93-87 5
8 TS1001008 Flat Washer, GB95-87 5
9 TS1001009 Stator 1
10 TS1001010 Flat Washer, GB95-87 5 6
11 TS1001011 Screw, GB845-85 ST4.8x65 2
12 TS1001012 Bearing, GB/T276-94 6200z 1
13 TS1001013 Rotor 1
14 TS1001014 Bearing, GB/T276-94 6202z 1
15 TS1001015 Wind Washer 1
16 TS1001016 Gear Box 1
17 TS1001017 Bearing, GB/T276-94 607z 1
18 TS1001018 C-ring, GB894.1-86 14 1
19 TS1001019 Wave Washer, GB/T955-1987 14 1
20 TS1001020 Gear 1
21 TS1001021 Spindle 1
22 TS1001022 C-ring, GB893.1-86 35 1
23 TS1001023 Bearing, GB/T276-94 6003z 1
24 TS1001024 Gear Box Cover 1
25 TS1001025 Spring Washer, GB/T8620.1-1987 5 3
26 TS1001026 Screw, GB819-85 M5X18 3
27 TS1001027 Key 1
28 TS1001028 Screw, GB/T818-2000 M5X10 3
29 TS1001029 Spring Washer, GB93-87 M5 4
30 TS1001030 Washer, GB/T8620.1-1987 5 3
31 TS1001031 Terminal Block 2
32 TS1001032 Electrical Conductivity Terminal 4
33 TS1001033 Copper Sheet 2
34 TS1001034 6.3 Terminal 4
35 TS1001035 6.3 Insulating Soft Sheath 4
36 TS1001036 Connector 1
37 TS1001037 Strain Relief 1
38 TS1001038 Motor Wire Cord 1
39 TS1001039 C-ring GB894.1-86 45 1
40 TS1001040 Bushing 1
41 TS1001041 In Flange 1
42 TS1001042 Blade 1
43 TS1001043 Out Flange 1
44 TS1001044 Blade Nut 1
45 TS1001045 Fllow Blade Board 1
46 TS1001046 Support Board 1
47 TS1001047 Connector Board 1
48 TS1001048 Flat Washer, GB95-87 6 16
49 TS1001049 Lock Nut, GB889.1-2000 M6 42
50 TS1001050 Shaft 1
51 TS1001051 Adjustment Board 1
52 TS1001052 Spring Washer, GB93-87 6 12
53 TS1001053 Bolt 8
54 TS1001054 Lock Washer 2
55 TS1001055 Nut, GB41-2000 M8 3
56 TS1001056 Nut, GB6172-2000 M8 1
57 TS1001057 Fixing Board 1
58 TS1001058 Lock Nut, GB889.1-2000 M5 1
59 TS1001059 Square Plate 1
60 TS1001060 Lock Shaft 1
61 TS1001061 Pin, GB879.1-2000 ø4X18 1
62 TS1001062 Knob A 1
63 TS1001063 Knob B 1
64 TS1001064 C-ring, GB894.1-86 12 2
65 TS1001065 Pin, GB13980.11-2000 ø4X30 1
66 TS1001066 Position Block 1
67 TS1001067 Left Anti-kickback 1
68 TS1001068 Spring 1
69 TS1001069 Knob Shaft 1
70 TS1001070 Washer 2
71 TS1001071 Spring 1
72 TS1001072 Right Anti-kickback 1
73 TS1001073 Screw 2
74 TS1001074 Left Blade Guard A 1
75 TS1001075 Lock Knob 1
76 TS1001076 Blade Guard Shaft 2
77 TS1001077 Blade Guard Body 1
78 TS1001078 Blade Guard Spring 1
79 TS1001079 Right Blade Guard A 1
80 TS1001080 Screw 6
81 TS1001081 Right Blade Guard B 1
82 TS1001082 Connector Screw 2
83 TS1001083 Lock Screw 2
84 TS1001084 Screw, GB/T77-2000 M5X10 2
85 TS1001085 Connector Board 4
86 TS1001086 Connector Shaft 1
87 TS1001087 Short Tube 1
88 TS1001088 Long Tube 1
89 TS1001089 Center Shaft 1
90 TS1001090 Left Blade Guard B 1
91 TS1001091 Fixing Shaft 1
92 TS1001092 Angle Pin 1
93 TS1001093 Nut, GB41-2000 M5 1
94 TS1001094 Nut, GB41-2000 M6 4
95 TS1001095 Support Board B 1
96 TS1001096 Lock Nut, GB889.1-2000 M8 6
97 TS1001097 Flat Washer, GB95-87 M8 2
98 TS1001098 Pin Support 1
99 TS1001099 Screw, GB70-85 M5X22 1
100 TS1001100 Lock Knob 1
101 TS1001101 Bolt, GB5780-2000 M6X85 2
102 TS1001102 Finger Board 1
103 TS1001103 Washer 1
104 TS1001104 Big Washer, GB96-85 M6 4
105 TS1001105 Support Board A 1
106 TS1001106 Wave Washer, GB/T955-1987 8 2
107 TS1001107 Screw 1
108 TS1001108 Tube 3
109 TS1001109 bolt, GB5783-2000 M6X20 4
110 TS1001110 Adjustment Support 1
111 TS1001111 Pin 1
112 TS1001112 Link Board 2
113 TS1001113 Link Pin 2
114 TS1001114 Nut 2
115 TS1001115 Adjustment Pin 1
116 TS1001116 Screw, GB70-2000 M8X14 1
117 TS1001117 Scale Board 1
118 TS1001118 Indicator 1
Key No. Part No. Description Qty Key No. Part No. Description Qty
10” TABLE SAW PARTS LIST
13
119 TS1001119 Screw, GB/T818-2000 M5X14 1
120 TS1001120 Screw, GB/T818-2000 M5X12 1
121 TS1001121 Block Plate 1
122 TS1001122 Wave Washer, GB/T955-1987 12 10
123 TS1001123 Spring 1
124 TS1001124 Adjustment bolt 1
125 TS1001125 Pin, GB13980.11-2000 ø2.5X22 1
126 TS1001126 Control Wheel 1
127 TS1001127 Wheel Handle 1
128 TS1001128 Screw 1
129 TS1001129 Wheel Label 1
130 TS1001130 Table insert A 1
131 TS1001131 Screw, GB70-85 M6X25 2
132 TS1001132 Screw 6
133 TS1001133 Work Table 1
134 TS1001134 Scale Label 1
135 TS1001135 Rivet, GB827-86 ø2X5 3
136 TS1001136 Date Label 1
137 TS1001137 Fance Base 2
138 TS1001138 Spring plate 2
139 TS1001139 Heat-shrink Tube 2
140 TS1001140 Bolt, GB5783-2000 M6X25 4
141 TS1001141 Washer, GB/T8620.1-1987 M6 6
142 TS1001142 Adjustment Washer 10
143 TS1001143 Nut, GB41-2000 M6 2
144 TS1001144 Press Plate 6
145 TS1001145 Base 1
146 TS1001146 Dust Port Cover 1
147 TS1001147 Heat-shrink Tube 1
148 TS1001148 Miter Gauge Storage 1
149 TS1001149 Spring Washer, GB93-87 M4 1
150 TS1001150 Washer, GB848-85 4 3
151 TS1001151 Screw, GB818-2000 M4X10 1
152 TS1001152 Spring Plate 1
153 TS1001153 Nut, GB170-2000 M4 1
154 TS1001154 Rubber Foot 4
155 TS1001155 Power Cord 1
156 TS1001156 Rubber Grommet 1
157 TS1001157 Strain Relief 1
158 TS1001158 Screw, GB845-85 ST4.2X19 2
159 TS1001159 Wire Holder 1
160 TS1001160 Switch Box 1
161 TS1001161 Dustproof Ring 1
162 TS1001162 Nylon Cable Ties 1
163 TS1001163 Inner Wire 1
164 TS1001164 Washer, GB96-85 4 4
165 TS1001165 Screw, GB845-85 ST4.2X16 4
166 TS1001166 Switch Base 1
167 TS1001167 Switch 1
168 TS1001168 Circuit Breaker 1
Key No. Part No. Description Qty Key No. Part No. Description Qty
10” TABLE SAW PARTS LIST
14
169 TS1001169 Breaker Nut 1
170 TS1001170 Inner Plate 1
171 TS1001171 Screw, GB819-85 M4X10 9
172 TS1001172 Gear Plate 1
173 TS1001173 Lock Nut, GB889.1-2000 M4 9
174 TS1001174 Knob Cover 1
175 TS1001175 Lock Knob 1
176 TS1001176 Angle Bolt 1
177 TS1001177 Miter Gauge 1
178 TS1001178 Guide Ruler 1
179 TS1001179 Pin 1
180 TS1001180 Gauge Pointer 1
181 TS1001181 Screw, GB/T818-2000 M4X8 1
182 TS1001182 Spring Washer, GB93-87 M4 1
183 TS1001183 Washer, GB848-85 M4 1
184 TS1001184 Table Insert B 1
185 TS1001185 Push Stick 1
186 TS1001186 Open Ended Wrench 1
187 TS1001187 Wrench 1
188 TS1001188 Bolt 1
189 TS1001189 Rear Plate 1
190 TS1001190 Spring 1
191 TS1001191 Spring Defence Board 1
192 TS1001192 Fence 1
193 TS1001193 Hex Bolt 2
194 TS1001194 Fence Support 1
195 TS1001195 Screw, GB/T818-2000 M4X10 1
196 TS1001196 Indicator 1
197 TS1001197 Long Nut 1
198 TS1001198 Bias Wheel 1
199 TS1001199 Pin 1
200 TS1001200 Spring Pin, GB13980.11-2000 ø3X22 1
201 TS1001201 Fence Handle 1
202 TS1001202 Pin 1
203 TS1001203 Front Nip Board 1
204 TS1001204 Dado Nut 1
Key No. Part No. Description Qty Key No. Part No. Description Specification Qty
15
PARTS LIST
Thank you for investing in a POWERTEC power tool. These products have been made to demanding, high-quality
standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of
purchase.
This guarantee does not affect your statutory rights. In case of any malfunction of your tool (failure, missing part, etc.),
please contact one of our service technician at our service line at 1-877-393-7121 from 9 AM to 5 PM, Monday to Friday,
Central time. Southern Technologies, LLC reserves the right to repair or replace the defective tool, at its discretion.
Normal wear and tear, including accessory wear, is not covered under guarantee. The product is guaranteed for 12
months if used for normal trade purposes. Any guarantee is invalid if the product has been overloaded or subject to
neglect, improper use or an attempted repair other than by an authorized agent. Heavy-duty, daily professional or hire
usage are not guaranteed. Due to continuous product improvement, we reserve the right to change the product specifi-
cation without prior notice.
SOUTHERN TECHNOLOGIES LLC. BENCH TOP AND STATIONARY POWER TOOL
LIMITED 1 YEAR WARRANTY AND 30-DAY SATISFACTION GUARANTEE POLICY
This product is manufactured by Southern Technologies LLC. under a trademark license from Southern Technolo-
gies LLC. All warranty communications should be directed to Southern Technologies LLC. 206 Terrace Dr. Munde-
lein, IL 60060, Attn: Southern Technologies Service Bench Top and Stationary Power Tool technical service at (toll
free) 1-877-393-7121.
30- DAY SATISFACTION GUARANTEE POLICY
During the first 30 days after the date of purchase, if you are dissatisfied with the performance of this Southern Tech-
nologies tool for any reason you may return the tool to the Retailer from which it was purchased for a full refund or
exchange. To receive a replacement tool you must present proof of purchase and return all original equipment pack-
aged with the original product. The replacement tool will be covered by the limited warranty for the balance of the one
year warranty period.
WHAT IS COVERED UNDER THE LIMITED ONE YEAR WARRANTY
This warranty covers all defects in workmanship or materials in this Southern Technologies tool for a one year period
from the date of purchase. This warranty is specific to this tool.
HOW TO OBTAIN SERVICE
To obtain service for this Southern Technologies tool you must return it, freight prepaid, to an authorized Southern
Technologies service center for bench top and stationary power tools. You may obtain the location of the authorized
service center nearest you by calling (toll free) 1-877-393-7121 or by logging on to the Southern Technologies website
at www.southerntechllc.com. When requesting warranty service, you must present the proof of purchase documenta-
tion, which includes a date of purchase. The authorized service center will repair any faulty workmanship, and either
repair or replace any defective part, at our option at no charge to you.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail and may not be transferred. This warranty only covers
defects arising under normal usage and does not cover any malfunction, failure or defect resulting from misuse, abuse,
neglect, alteration, modification or repair by other than an authorized service center for Southern Technologies bench
top and stationary power tools. Warranty excludes: Consumable Items i.e. Saw Blades, Knives, Belts and Disc, Cooling
blocks etc.
SOUTHERN TECHNOLOGIES LLC., MAKES NO WARRANTIES, REPRESENTATIONS OR PROMISES AS TO THE
QUALITY OR PERFORMANCE OF ITS POWER TOOLS OTHER THAN THOSE SPECIFICALLY STATED IN THIS
WARRANTY.
WARRANTY
16
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, including warranties of merchant-
ability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to one year from the date
of purchase. Southern Technologies LLC. is not responsible for direct, indirect, incidental or consequential damages.
Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitations may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights which vary from state to state.
NOTE
17
WARRANTY
Southern Technologies, LLC
206 Terrace Drive
Mundelein, Illinois 60060
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Master Flow MOTOR24DD Operating instructions
-
DeWalt DWE7470 User manual
-
Grizzly W1761 Owner's manual
-
JET JPS-10 Owner's manual
-
-
Rikon Power Tools 11-200 User manual
-
-
Ryobi Table Saw User manual
-
-
Delta 36-725 T2 Owner's manual