Champion 41533 Owner's Manual & Operating Instructions

Brand: Champion

Model: 41533

Category: Power generators

Type: Owner's Manual & Operating Instructions

OWNER’S MANUAL & OPERATING INSTRUCTIONS

10006 Santa Fe Springs Road

Santa Fe Springs CA 90670

USA / 1-877-338-0999

www.championpowerequipment.com

9200 Starting Watts / 7200 Running Watts

PORTABLE GENERATOR

SAVE THESE INSTRUCTIONS

Important Safety Instructions

are included in this manual.

MADE IN CHINA

REV 41533-20110701

Wireless Remote Electric Start

41533

MODEL NUMBER

Have questions or need assistance?

Do not return this product to the store!

WE ARE HERE TO HELP!

Visit our website:

www.championpowerequipment.com

for more info:

• Product Info & Updates

• Frequently Asked Questions

• Tech Bulletins

• Product Registration

– or –

Call our Customer Care Team Toll-Free at:

1-877-338-0999

24/7 Tech Support: (562) 204-1188

41533

Wireless Remote Electric Start

PORTABLE GENERATOR

9200 Starting Watts / 7200 Running Watts

TABLE OF CONTENTS

Introduction ............................. 1

Introduction ........................... 1

Portable Power Generator .................. 1

Accessories ........................... 1

This Booklet ........................... 1

Manual Conventions. . . . . . . . . . . . . . . . . . . . . . . . 2

Safety Rules ............................. 3

Controls and Features ...................... 5

Generator ............................. 5

Power Panel ........................... 6

Wireless Remote Control .................. 7

Remote Control Power Consumption ........ 7

Power Panel Load Management ........... 7

Parts Included ......................... 8

Wheel Kit .......................... 8

Other ............................. 8

Assembly ............................... 9

Remove the Generator from the Shipping Carton .. 9

Install the Wheel Kit ..................... 9

Install the Support Leg ................... 9

Connect the Battery ..................... 9

Add Engine Oil ........................ 10

Add Fuel ............................ 11

Grounding ........................... 11

Operation .............................. 12

Generator Location ..................... 12

Grounding ........................... 12

Surge Protection ....................... 12

Wireless Remote Start ................... 12

Starting the Engine without Remote .......... 12

Connecting Electrical Loads ............... 13

Stopping the Engine .................... 13

Do Not Overload Generator ................ 13

Capacity .......................... 13

Power Management ................... 13

Wattage Reference Chart ................. 14

Operation at High Altitude ............... 14

Maintenance and Storage ................... 15

Engine Maintenance .................... 15

Oil .............................. 15

Spark Plugs ........................ 15

Air Filter .......................... 15

Spark Arrester ...................... 16

Cleaning .......................... 16

Adjustments ........................ 16

Maintenance Schedule ................ 16

Generator Maintenance .................. 17

Storage ............................. 17

Generator Storage .................... 17

Disconnect the Battery ................ 17

Charge the Battery ................... 17

Speciﬁcations ........................... 18

Engine Speciﬁcations ................... 18

Generator Speciﬁcations ................. 18

Fuel ............................... 18

Oil ................................ 18

Spark Plugs .......................... 18

Valve Clearance ....................... 18

FCC Statement for Remote Control Device ..... 18

Parts Diagram ........................ 19

Parts List ............................ 20

Engine Parts Diagram ................... 21

Engine Parts List ...................... 22

Wiring Diagram ........................ 23

Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . 24

Warranty .............................. 25

Warranty Qualiﬁcations .................. 25

Repair/Replacement Warranty .............. 25

Do Not Return The Unit To

The Place Of Purchase .................. 25

Warranty Exclusions .................... 25

Normal Wear ....................... 25

Installation, Use and Maintenance ........ 25

Other Exclusions ..................... 25

Limits of Implied Warranty

and Consequential Damage ............. 25

Contact Information. . . . . . . . . . . . . . . . . . . . . 25

Address ........................... 25

Customer Service .................... 25

Technical Service .................... 25

Emission Control System Warranty .......... 26

1 REV 41533-20110701

ENGLISH 41533

Introduction

Congratulations on your purchase of a Champion

Power Equipment generator. CPE designs and builds

generators to strict speciﬁcations. With proper use and

maintenance, this generator will bring years of satisfying

service.

Portable Power Generator

This unit is a gasoline engine driven, alternating current

(AC) generator. It is designed to supply electrical power

for lighting, appliances, tools and similar equipment.

Record the model and serial numbers as well as date and place of purchase for future reference. Have this

information available when ordering parts and when making technical or warranty inquiries.

Accessories

Champion Power Equipment manufactures and sells

accessories designed to help you get the most from

your purchase. To ﬁnd out more about our covers, power

cables and storm kits, please visit our web site at:

www.championpowerequipment.com

This Booklet

Every effort has been made to ensure the accuracy and

completeness of the information in this manual. We reserve

the right to change, alter and/or improve the product and

this document at any time without prior notice.

Champion Power Equipment Support

Model Number

Serial Number

Date of Purchase

Purchase Location

1-877-338-0999

41533

For Oil Type see ‘Add Engine Oil‘ section. For Fuel Type see ‘Add Fuel‘ section.

INTRODUCTION

REV 41533-20110701 2

41533 ENGLISH

MANUAL CONVENTIONS

This manual uses the following symbols to help differentiate between different kinds of information. The safety symbol

is used with a key word to alert you to potential hazards in operating and owning power equipment.

Follow all safety messages to avoid or reduce the risk of serious injury or death.

CAUTION indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION

CAUTION used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in property damage.

CAUTION

DANGER indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

DANGER

WARNING indicates a potentially hazardous

situation which, if not avoided, could result in

death or serious injury.

WARNING

If you have questions regarding your generator, we can

help. Please call our help line at 1-877-338-0999

NOTE

3 REV 41533-20110701

ENGLISH 41533

SAFETY RULES

The engine exhaust from this product contains

chemicals known to the state of California to cause

cancer, birth defects, or other reproductive harm.

Read this manual thoroughly before operating your

generator. Failure to follow instructions could result

in serious injury or death.

Generator exhaust contains carbon monoxide, a

colorless, odorless, poison gas. Breathing carbon

monoxide will cause nausea, dizziness, fainting or

death. If you start to feel dizzy or weak, get to fresh

air immediately.

Operate generator outdoors only in a well ventilated

area.

DO NOT operate the generator inside any building,

including garages, basements, crawlspaces and

sheds, enclosure or compartment, including the

generator compartment of a recreational vehicle.

DO NOT allow exhaust fumes to enter a conﬁned

area through windows, doors, vents or other

openings.

DANGER CARBON MONOXIDE: using a generator

indoors CAN KILL YOU IN MINUTES.

Rotating parts can entangle hands, feet, hair,

clothing and/or accessories.

Traumatic amputation or severe laceration can result.

Keep hands and feet away from rotating parts.

Tie up long hair and remove jewelry.

Operate equipment with guards in place.

DO NOT wear loose-ﬁtting clothing, dangling

drawstrings or items that could become caught.

Generator produces powerful voltage.

DO NOT touch bare wires or receptacles.

DO NOT use electrical cords that are worn, damaged

or frayed.

DO NOT operate generator in wet weather.

DO NOT allow children or unqualiﬁed persons to

operate or service the generator

Use a ground fault circuit interrupter (GFCI) in damp

areas and areas containing conductive material such

as metal decking.

Use approved transfer equipment to isolate generator

from your electric utility and Notify your utility

company before connecting your generator to your

power system.

Sparks can result in ﬁre or electrical shock.

When servicing the generator:

Disconnect the spark plug wire and place it where it

cannot contact the plug.

DO NOT check for spark with the plug removed.

Use only approved spark plug testers.

Running engines produce heat. Severe burns can

occur on contact.

Combustible material can catch ﬁre on contact.

DO NOT touch hot surfaces.

Avoid contact with hot exhaust gases.

Allow equipment to cool before touching.

Maintain at least three feet of clearance on all sides

to ensure adequate cooling.

Maintain at least ﬁve feet of clearance from

combustible materials.

DANGER

WARNING

REV 41533-20110701 4

41533 ENGLISH

SAFETY RULES

Fuel and fuel vapors are highly ﬂammable and

extremely explosive.

Fire or explosion can cause severe burns or death.

Unintentional startup can result in entanglement,

traumatic amputation or laceration.

When adding or removing fuel:

Turn the generator off and let it cool for at least two

minutes before removing the fuel cap. Loosen the

cap slowly to relieve pressure in the tank.

Only ﬁll or drain fuel outdoors in a well-ventilated area.

DO NOT overﬁll the fuel tank.

Always keep fuel away from sparks, open ﬂames,

pilot lights, heat and other sources of ignition.

DO NOT light or smoke cigarettes.

When starting the generator:

DO NOT attempt to start a damaged generator.

Make certain that the gas cap, air ﬁlter, spark plug,

fuel lines and exhaust system are properly in place.

Allow spilled fuel to evaporate fully before

attempting to start the engine.

Make certain that the generator is resting ﬁrmly on

level ground.

When operating the generator:

DO NOT move or tip the generator during operation.

DO NOT tip the generator or allow fuel or oil to spill.

When transporting or servicing the generator:

Make certain that the fuel shutoff valve is in the off

position and the fuel tank is empty.

Disconnect the spark plug wire.

When storing the generator:

Store away from sparks, open ﬂames, pilot lights,

heat and other sources of ignition.

Rapid retraction of the starter cord will pull hand and

arm towards the engine faster than you can let go.

Unintentional startup can result in entanglement,

traumatic amputation or laceration.

Broken bones, fractures, bruises or sprains could result.

When starting engine, pull the starter cord slowly

until resistance is felt and then pull rapidly to avoid

kickback.

DO NOT start or stop the engine with electrical

devices plugged in.

Exceeding the generator’s running capacity can

damage the generator and/or electrical devices

connected to it.

DO NOT overload the generator.

Start the generator and allow the engine to stabilize

before connecting electrical loads.

Connect electrical equipment in the off position,

and then turn them on for operation.

Turn electrical equipment off and disconnect before

stopping the generator.

DO NOT tamper with the governed speed.

DO NOT modify the generator in any way.

Improper treatment or use of the generator can

damage it, shorten its life and void your warranty.

Use the generator only for intended uses.

Operate only on level surfaces.

DO NOT expose generator to excessive moisture,

dust, or dirt.

DO NOT allow any material to block the cooling slots.

If connected devices overheat, turn them off and

disconnect them from the generator.

DO NOT use the generator if:

– Electrical output is lost

– Equipment sparks, smokes or emits ﬂames

– Equipment vibrates excessively

Operation of this equipment may create sparks that

can start ﬁres around dry vegetation.

A spark arrestor may be required. The operator

should contact local ﬁre agencies for laws or

regulations relating to ﬁre prevention requirements.

CAUTION

WARNING

DANGER

CAUTION

5 REV 41533-20110701

ENGLISH 41533

Read this owner’s manual before operating your generator. Familiarize yourself with the location and function of the

controls and features. Save this manual for future reference.

Generator

CONTROLS AND FEATURES

(1) Fuel Tank – 5.9 gallon (22.4 L) capacity fuel tank.

(2) Auto-Choke – Used to start the engine. No manual

adjustment required.

(3) Fuel Valve – Used to turn fuel supply on and off to

engine.

(4) Air Cleaner – Protects the engine by ﬁltering dust

and debris from the intake air.

(5) Recoil Starter – Used to manually start the engine.

(6) Quick Drain Tube – Used to easily and quickly

drain oil from the engine.

(7) Oil Filler Cap – Check and ﬁll engine oil level.

(8) Battery – Used to start the engine. Provides 12V

DC to the electric starter and receiver control

module.

(9) Power Panel – See “Power Panel” section.

REV 41533-20110701 6

41533 ENGLISH

Power Panel

CONTROLS AND FEATURES

(1) Intelligauge – Three mode digital meter for

displaying running hours, voltage and hertz.

(2) Battery Switch – Enables/disables starting

electrically – via remotely or by Ignition Switch.

(3) Circuit Breakers – Protects the generator against

electrical overloads. Push to reset breaker.

(4) Ignition Switch – Used to start or stop the

generator.

(5) 120 Volt AC, 30 Amp Twist-Lock Receptacle

(NEMA L5-30R) –

May be used to supply electrical

power for the operation of 120 Volt AC, 30 Amp,

single phase 60 Hz electrical loads.

(6) 120/240 Volt AC, 30 Amp Twist-Lock Receptacle

(NEMA L14-30R) –

May be used to supply

electrical power for the operation of 120

and/or 240 Volt AC, 30 Amp, single phase 60 Hz

electrical loads.

(7) 120 Volt AC, 20 Amp Duplex (2)

(NEMA 5-20R) – May be used to supply electrical

power for the operation of 120 Volt AC, 20 Amp,

single phase 60 Hz electrical loads.

(8) Ground Terminal – Consult an electrician for local

grounding regulations.

7 REV 41533-20110701

ENGLISH 41533

CONTROLS AND FEATURES

Wireless Remote Control

This generator is equipped with a wireless remote

control system for starting and stopping. The system

consists of (4) main components:

1. Receiver Control Module (RCM)

2. Wireless Remote

3. Battery Switch

4. Ignition Switch

The Remote Control functions are enabled when:

1. The Ignition Switch is in the “ON” position, AND

2. The Battery Switch is in the “ON” position.

The Remote Control functions are disabled if either of

the above conditions is not met.

To start the generator by Remote Control, press the

“START” button on the Remote one time. The engine

will attempt to start (6) times. The RCM controls

the Auto Choke during each attempt to start. If the

generator does not start, call Champion Customer Care

team for assistance at 1-877-338-0999.

To stop the generator by Remote Control, press the

“STOP” button on the Remote one time.

Remote Control Power Consumption

While the Ignition Switch is in the “ON: position, the

RCM is active and waiting for a remote signal. This

function requires electrical current from the battery.

If the Ignition Switch is left in the “ON” position for

extended periods (several weeks), the battery can be

completely drained.

Moving the Ignition Switch to the “OFF” position

disables the Remote functions, but the RCM still

consumes approximately 2 mA from the battery.

To prevent battery drain, press the Battery Switch to the

“OFF” position. This disconnects power to the RCM so

there is no current draw on the battery.

Power Panel Load Management

When the generator initially starts by the Remote, no

voltage is supplied to the Power Panel for approximately

15 seconds. This allows the engine to reach full speed

before electrical loads are applied to the generator.

When the generator is stopped by the Remote, the

voltage to the Power Panel is immediately turned off.

Then the engine stops after the “STOP” button on the

Remote is pressed. Turning the Power Panel voltage

off before the engine shutdown protects connected

appliances from being damaged by non-60 Hz voltage

while the generator coasts to a stop.

The on/off voltage delay at startup and shut down only

happen when the Remote Control is used. There is no

voltage delay when the pushbutton electric start or recoil

start method is used.

When the pushbutton electric start or recoil start

method is used, the operator must be sure all electrical

loads (appliances) are turned OFF during startup and

shutdown. Damage to the generator or the attached

appliances can be caused by starting or stopping the

generator while appliances are plugged in and turned ON.

Power Panel Load Management Cont’d.

REV 41533-20110701 8

41533 ENGLISH

CONTROLS AND FEATURES

Parts Included

Your 41533 Gasoline Powered Generator ships with the

following parts:

Wheel Kit

– 10” Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

– Flange Bolt (M10x120 for Wheel) . . . . . . . . . . . . 2

– Bushing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

– Flat Washer 10 . . . . . . . . . . . . . . . . . . . . . . . . . 2

– Nut (M10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

– Support Leg w/Vibration Mounts . . . . . . . . . . . . . 1

– Flange Bolt (M8x16 for Support Leg) . . . . . . . . . . 2

– Nut (M8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Other

– Oil Funnel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

– Oil . . . . . . . . . . . . . . . . . . . . . . . 1.16 qt. (1.1 L)

– Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

– Spark Plug Socket . . . . . . . . . . . . . . . . . . . . . . . 1

– Cap Screw (M5x12 for Battery Terminals) . . . . . . . 2

– Nut (M5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

(Battery Bolts)

9 REV 41533-20110701

ENGLISH 41533

ASSEMBLY

Your generator requires some assembly. This unit ships

from our factory without oil. It must be properly serviced

with fuel and oil before operation.

If you have any questions regarding the assembly of your

generator, call our help line at 1-877-338-0999. Please

have your serial number and model number available.

Remove the Generator from the Shipping Carton

1. Set the shipping carton on a solid, ﬂat surface.

2. Remove everything from the carton except the

generator.

3. Carefully cut each corner of the box from top to

bottom. Fold each side ﬂat on the ground to provide a

surface area to install the wheel kit and support leg.

Install the Wheel Kit

You will need the following tools to install the wheels:

• 17 mm wrench OR adjustable wrench (not included)

• Socket wrench with a 16 mm socket (not included)

• Pliers (not included)

1. Before adding fuel and oil, tip the generator on it’s side.

2. Slide the M10x120 wheel bolt through the washer,

sleeve and wheel.

3. Slide the bolt through the mount point on the frame.

4. Fasten securely with the M10 nut.

5. Repeat steps 2-4 to attach the second wheel.

Install the Support Leg

1. Attach the support leg to the generator frame with

cap screws (M8x16) and nuts (M8).

2. Tip the generator slowly so that it rests on the

wheels and support leg.

The wheel kit is not intended for over-the-road use.

CAUTION

Connect the Battery

1. Remove the protective cover from the red (+) lead on

the battery.

2. Attach the red (+) lead to the red (+) terminal on the

battery with the cap screw (M5x12) and secure with

the lock washer (M5).

3. Repeat steps 1-2 for the black (–) battery lead.

REV 41533-20110701 10

41533 ENGLISH

1. Place the generator on a ﬂat, level surface.

2. Remove oil ﬁll cap/dipstick to add oil.

3. Add 1.16 qt (1.1 L) of oil (included) and replace oil

ﬁll cap/dipstick. See “Speciﬁcations” pages for oil

recommendations based on operating conditions.

4. Check engine oil level daily and add as needed.

The recommended oil type is 10W-30 4-cycle

automotive oil.

NOTE

The engine is equipped with a low-oil-shutoff and

will stop when the oil level in the crankcase falls

below the threshold level.

CAUTION

Add Engine Oil

DO NOT attempt to crank or start the engine before

it has been properly ﬁlled with the recommended

type and amount of oil. Damage to the generator as

a result of failure to follow these instructions will

void your warranty.

CAUTION

ASSEMBLY

Check oil often during the break-in period. Refer to the

Maintenance section for recommended service intervals.

NOTE

The generator rotor has a sealed, pre-lubricated ball

bearing that requires no additional lubrication for

the life of the bearing.

NOTE

Add Engine Oil Cont’d.

11 REV 41533-20110701

ENGLISH 41533

Add Fuel

1. Use clean, fresh, regular unleaded fuel with a

minimum octane rating of 85 and an ethanol content

of less than 10% by volume.

2. DO NOT mix oil with fuel.

3. Clean the area around the fuel cap.

4. Remove the fuel cap.

5. Slowly add fuel to the tank. DO NOT overﬁll. Allow

approximately ¼ inch of space for fuel expansion.

6. Screw on the fuel cap and wipe away any spilled fuel.

Use regular unleaded gasoline with a minimum

octane rating of 85.

DO NOT mix oil and gasoline.

Fill tank to approximately ¼ inch below the top of

the tank to allow for fuel expansion.

DO NOT ﬁll fuel tank indoors.

DO NOT ﬁll fuel tank when the engine is running or hot.

DO NOT overﬁll the fuel tank.

DO NOT light cigarettes or smoke when ﬁlling the

fuel tank.

CAUTION

ASSEMBLY

Grounding

Your generator must be properly connected to an

appropriate ground to help prevent electric shock.

A ground terminal connected to the frame of the generator

has been provided on the power panel. For remote

grounding, connect of a length of heavy gauge (12 AWG

minimum) copper wire between the generator ground

terminal and a copper rod driven into the ground. We

strongly recommend that you consult with a qualiﬁed

electrician to ensure compliance with local electrical codes.

Failure to properly ground the generator can result

in electric shock.

WARNING

REV 41533-20110701 12

41533 ENGLISH

Generator Location

Please consult your local authority. In some areas,

generators must be registered with the local utility.

Generators used at construction sites may be subject to

additional rules and regulations.

This generator must have at least ﬁve feet of clearance

from combustible material. Leave at least three feet

of clearance on all sides of the generator to allow for

adequate cooling, maintenance and servicing.

Place the generator in a well-ventilated area. DO NOT

place the generator near vents or intakes where exhaust

fumes could be drawn into occupied or conﬁned

spaces. Carefully consider wind and air currents when

positioning generator.

Grounding

The generator system ground connects the frame to the

ground terminals on the power panel.

The generator (stator winding) is isolated from the frame

and from the AC receptacle ground pin. Electrical devices

that require a grounded receptacle pin connection may not

function properly.

Surge Protection

Electronic devices, including computers and many

programmable appliances use components that are

designed to operate within a narrow voltage range and

may be affected by momentary voltage ﬂuctuations.

While there is no way to prevent voltage ﬂuctuations, you

can take steps to protect sensitive electronic equipment.

1. Install UL1449, CSA-listed, plug-in surge suppressors

on the outlets feeding your sensitive equipment.

Surge suppressors come in single- or multi-outlet

styles. They’re designed to protect against virtually

all short-duration voltage ﬂuctuations.

Voltage ﬂuctuation may impair the proper

functioning of sensitive electronic equipment.

CAUTION

OPERATION

Starting the Engine without Remote

1. Make certain the generator is on a ﬂat, level surface.

2. Turn off all electrical loads connected to the generator.

Never start or stop the generator with electrical

devices plugged in and turned on.

3. Turn the Fuel Valve to the “ON” position.

4. Press the Battery Switch to “ON”.

5. ELECTRIC START: Press the switch to the “START”

position.

6. RECOIL START: Pull the starter cord slowly until

resistance is felt and then pull rapidly.

Wireless Remote Start

Wireless remote starting is only possible within 80 feet of

the generator.

Do not attempt to adjust the carburetor choke. The remote

system will automatically close and open the choke.

1. Make certain the generator is on a ﬂat, level surface.

2. Press the Ignition Switch to “ON”.

3. Press the Battery Switch to “ON”.

4. Turn the Fuel Valve to the “ON” position.

5. To start the engine, press and release the “START”

button on the handheld Remote Control device. DO

NOT hold the button down, only press the button

once. The engine will attempt to start 6 times.

6. A safety feature is provided which delays the

electrical power availability during starting mode.

The delay lasts for approximately 15 seconds. The

delay is provided to prevent damage to the generator

if electrical loads are inadvertently turned on during

engine startup.

7. If the generator fails to start, check the battery

condition and cable connections.

If the engine starts but does not run make certain

that the generator is on a ﬂat, level surface. The

engine is equipped with a low oil sensor that will

prevent the engine from running when the oil level

falls below a critical threshold.

NOTE

13 REV 41533-20110701

ENGLISH 41533

Connecting Electrical Loads

1. Let the engine stabilize and warm up for a few

minutes after starting

2. Plug in and turn on the desired 120/240 Volt AC

single phase, 60 Hz electrical loads.

– DO NOT connect 3-phase loads to the generator.

– DO NOT connect 50 Hz loads to the generator.

– DO NOT overload the generator.

Stopping the Engine

1. Turn off all electrical loads connected to the

generator. Never start or stop the generator with

electrical devices plugged in and turned on.

2. Press and release the STOP button on the Remote

Control device OR turn the Ignition Switch to the

“OFF” position.

3. Turn the Fuel Valve to the “OFF” position.

Important: If the generator will be moved or stored turn

the Fuel Valve to the “OFF” position, press the Ignition

Switch and the Battery Switch on the power panel to the

“OFF” position.

Connecting a generator to your electric utility

company’s power lines or to another power source

may be against the law. In addition this action,

if done incorrectly, could damage your generator

and appliances and could cause serious injury or

even death to you or a utility worker who may be

working on nearby power lines. If you plan to run a

portable electric generator during an outage, please

notify your electric utility company immediately

and remember to plug your appliances directly

into the generator. Do not plug the generator into

any electric outlet in your home. Doing so could

create a connection to the utility company power

lines. You are responsible for ensuring that your

generator’s electricity does not feed back into the

electric utility power lines.

If the generator will be connected to a building

electrical system, consult your local utility company

or a qualiﬁed electrician. Connections must isolate

generator power from utility power and must comply

with all applicable laws and codes.

NOTE

OPERATION

Do Not Overload Generator

Capacity

Follow these simple steps to calculate the running and

starting watts necessary for your purposes.

1. Select the electrical devices you plan on running at

the same time.

2. Total the running watts of these items. This is

the amount of power you need to keep your items

running.

3. Identify the highest starting wattage of all devices

identiﬁed in step 1. Add this number to the number

calculated in step 2. Surge wattage is the extra

burst of power needed to start some electric driven

equipment. Following the steps listed under “Power

Management” will guarantee that only one device will

be starting at a time.

Power Management

Use the following formula to convert voltage and

amperage to watts:

Volts x Amps = Watts

To prolong the life of your generator and attached

devices, follow these steps to add electrical load:

1. Start the generator with no electrical load attached

2. Allow the engine to run for several minutes to stabilize.

3. Plug in and turn on the ﬁrst item. It is best to attach

the item with the largest load ﬁrst.

4. Allow the engine to stabilize.

5. Plug in and turn on the next item.

6. Allow the engine to stabilize.

7. Repeat steps 5-6 for each additional item.

Never exceed the speciﬁed capacity when adding

loads to the generator.

NOTE

REV 41533-20110701 14

41533 ENGLISH

OPERATION

Wattage Reference Chart

Use the chart to determine approximate wattage

requirements for your equipment.

Item

Running

Watts (A)

Starting

Watts (B)

Essentials

Light Bulb 100W 100

Refrigerator/Freezer 1200 2400

Freezer 500 500

Sump Pump 600 1800

Well Pump 1 HP 2000 4000

Water Heater 4000

Security System 180

AM/FM Radio 300

Garage Door Opener 1/2 HP 500 600

Battery Charger 12V DC 110

Heating/Cooling

Air Conditioner 12000 BTU 1700 2500

Fan 300 600

Furnace Fan 1/3 HP 1200 2000

Home Appliances

Microwave 1000W 1000

Electric Range - One Element 1500

Electric Skillet 1250

Coffee Maker 1500

Clothes Washer 1200

Entertainment

CD/DVD Player / VCR 100

Stereo Receiver 450

Television 27” 500

PC with 15” Monitor 800

Job Site

Belt Sander 3” 1000 1500

Bench Grinder 6” 700 1500

Circular Saw 1500 1500

Compressor 1 1/2 HP 2500 2500

Edge Trimmer 500 500

Hand Drill 1/2” 1000 1000

Lawn Mower 1200 1800

Paint Sprayer 600 1200

Table Saw 2000 2000

Exceeding speciﬁed load capacity can result in

damage to the generator.

To determine total wattage necessary to power

a device, ADD Running Watts to Starting Watts.

(A+B). Starting watts can exceed three times the

running watts. The values in the following table are

approximate. Refer to your tool or appliance for actual

wattage consumption.

CAUTION

Operation at High Altitude

The density of air at high altitude is lower than at sea

level. Engine power is reduced as the air mass and air-

fuel ratio decrease. Engine power and generator output

will be reduced approximately 3½% for every 1000

feet of elevation above sea level. This is a natural trend

and cannot be changed by adjusting the engine. At

sufﬁciently high altitudes increased exhaust emissions

can also result due to the increased enrichment of the

air fuel ratio. Other high altitude issues can include hard

starting, increased fuel consumption and spark plug

fouling.

Part Number Altitude

Standard main jet

ST190FD-2-1131000-17

6000 Feet

(1800 Meters)

Altitude main jet

490.131017.01

Operation using the alternative main jet at

elevations lower than the recommended minimum

altitude can damage the engine. For operation at

lower elevations, the standard main jet must be

used. Operating the engine with the wrong engine

conﬁguration at a given altitude may increase

its emissions and decrease fuel efﬁciency and

performance.

WARNING

To alleviate high altitude issues other than the natural

power loss, Champion Power Equipment can provide a

high altitude carburetor main jet. The alternative main

jet and installation instructions can be obtained by

contacting Customer Support. Installation instructions

are also available in the Technical Bulletin area of the

Champion Power Equipment internet site.

The part number and recommended minimum altitude

for the application of the high altitude carburetor main

jet is listed in the table below.

15 REV 41533-20110701

ENGLISH 41533

The owner/operator is responsible for all periodic

maintenance.

Complete all scheduled maintenance in a timely manner.

Correct any issue before operating the generator.

Never operate a damaged or defective generator.

Tampering with the factory set governor will void

your warranty.

Air Filter

1. Remove the snap-on cover holding the air ﬁ lter to

the assembly.

2. Remove the foam element.

3. Wash in liquid detergent and water. Squeeze

thoroughly dry in a clean cloth.

4. Saturate in clean engine oil.

5. Squeeze in a clean, absorbent cloth to remove all

excess oil.

6. Place the ﬁ lter in the assembly.

7. Reattach the air ﬁ lter cover and snap in place.

Spark Plugs

1. Remove the spark plug cable from the spark plug.

2. Use the spark plug tool that shipped with your

generator to remove the plug.

3. Inspect the electrode on the plug. It must be clean and

not worn to produce the spark required for ignition.

4. Make certain the spark plug gap is 0.7 - 0.8mm or

(0.028 - 0.031 in.).

5. Refer to the spark plug recommendation chart when

replacing the plug.

6. Carefully thread the plug into the engine.

7. Use the spark plug tool to ﬁ rmly install the plug.

8. Attach the spark plug wire to the plug.

For service or parts assistance, contact our help

line at 1-8 77-338-0999

NOTE

Maintenance, replacement, or repair of emission

control devices and systems may be performed

by any non-road engine repair establishment or

individual.

NOTE

WARNING

Improper maintenance will void your warranty.

WARNING

Oil Cont’d.

0.7 - 0.8 mm

0.028 - 0.031 in.

MAINTENANCE AND STORAGE

Once oil has been added, a visual check should show

oil about 1-2 threads from running out of the ﬁ ll hole.

If using the dipstick to check oil level, DO NOT screw

in the dipstick while checking.

NOTE

Engine Maintenance

To prevent accidental starting, remove and ground spark

plug wire before performing any service.

Oil

Change oil when the engine is warm. Refer to the oil

speciﬁ cation to select the proper grade of oil for your

operating environment.

1. Remove oil ﬁ ll cap/dipstick.

2. Use pliers to slide the spring clamp down the oil

drain hose and pull the hose off the plug bracket.

3. Point the hose into a drain pan and allow the oil to

drain completely. Note: The hose end must be lower

than the engine base to allow the oil to drain.

4. Replace oil drain hose onto plug bracket and slide

spring clamp back into position.

5. Add 1.16 qt (1.1 L) of oil and replace oil ﬁ ll

cap/dipstick.

6. Dispose of used oil at an approved waste

management facility.

REV 41533-20110701 16

41533 ENGLISH

Adjustments

The air-fuel mixture is not adjustable. Tampering with

the governor can damage your generator and your

electrical devices and will void your warranty. CPE

recommends that you contact our service line at

1-877-338-0999 for all other service and/or adjustment

needs.

Maintenance Schedule

Follow the service intervals indicated in the following

maintenance schedule.

Service your generator more frequently when operating

in adverse conditions.

Contact our helpline at 1-877-338-0999 to locate the

nearest Champion Power Equipment certiﬁed service

dealer for your generator or engine maintenance needs.

Use a damp cloth to clean exterior surfaces of the engine.

Use a soft bristle brush to remove dirt and oil.

Use an air compressor (25 PSI) to clear dirt and debris

from the engine.

Cleaning

DO NOT spray engine with water.

CAUTION

Water can contaminate the fuel system.

Spark Arrester

1. Allow the engine to cool completely before servicing

the spark arrester.

2. Remove the three screws holding the cover plate

which retains the end of the spark arrester to the

mufﬂer.

3. Remove the spark arrester screen.

4. Carefully remove the carbon deposits from the spark

arrester screen with a wire brush.

5. Replace the spark arrester if it is damaged.

6. Position the spark arrester in the mufﬂer and attach

with the three screws.

Failure to clean the spark arrester will result in

degraded engine performance.

CAUTION

MAINTENANCE AND STORAGE

Federal and local laws and administrative

requirements indicate when and where spark

arresters are required. When ordered, spark

arresters are required for operation of this generator

in National Forest lands. In California, this

generator must not be used on any forest- covered

land, brush-covered land, or grass- covered land

unless the engine is equipped with a spark arrester.

NOTE

*To be performed by knowledgeable, experienced owners or

Champion Power Equipment certiﬁed dealers.

Every 8 hours or daily

Check oil level

Clean around air intake and mufﬂer

First 5 Hours

Change oil

Every 50 hours or every season

Clean air ﬁlter

Change oil if operating under heavy load or in hot environments

Every 100 hours or every season

Change oil

Clean/Adjust spark plug

Check/Adjust valve clearance *

Clean spark arrester

Clean fuel tank and ﬁlter *

Every 250 hours

Clean combustion chamber*

Every 3 years

Replace fuel line

17 REV 41533-20110701

ENGLISH 41533

MAINTENANCE AND STORAGE

Generator Maintenance

Make certain that the generator is kept clean and stored

properly. Only operate the unit on a ﬂat, level surface in

a clean, dry operating environment. DO NOT expose the

unit to extreme conditions, excessive dust, dirt, moisture

or corrosive vapors.

Storage

The generator should be started at least once every 14

days and allowed to run for at least 20 minutes. For

longer term storage, please follow these guidelines.

Generator Storage

1. Allow the engine to cool completely before storage.

2. Clean the generator according to the instructions in

the Maintenance section.

3. Turn the Fuel Valve to the “OFF” position.

4. Be sure all appliances are disconnected from the

generator. Start the engine and let it run until the

fuel in the line and the carburator is consumed and

the engine dies.

5. Press the Battery Switch to “OFF”.

6. Add a fuel stabilizer into the fuel tank.

7. Change the oil.

8. Remove the spark plug and pour about ½ ounce

of oil into the cylinder. Crank the engine slowly to

distribute the oil and lubricate the cylinder.

9. Reattach the spark plug.

10. Store the unit in a clean, dry place out of direct

sunlight.

Use a damp cloth to clean exterior surfaces of the generator.

Use a soft bristle brush to remove dirt and oil.

Use an air compressor (25 PSI) to clear dirt and debris

from the generator.

Inspect all air vents and cooling slots to ensure that they

are clean and unobstructed.

DO NOT use a garden hose to clean the generator.

Water can enter the generator through the cooling

slots and damage the generator windings.

CAUTION

Disconnect the Battery

1. Remove the protective cover from the black/negative

battery lead.

2. Disconnect the black/negative lead from the black/

negative terminal on the battery and store the cap

screw (M5x12) and lock washer (M5).

3. Repeat steps 1-2 for the red/positive battery lead.

4. Store the battery in a cool, dry place.

Charge the Battery

For generators equipped with batteries for electric

starting, proper battery maintenance and storage

should be followed. An automatic battery charger with

automatic trickle charging capability should be used to

charge the battery. Maximum charging rate should not

exceed 1.5 amps. Follow the instructions included with

the battery charger. The battery should be fully charged

at least once per month.

Generator exhaust contains odorless and colorless

carbon monoxide gas.

To avoid accidental or unintended ignition of your

remote start generator during periods of storage,

the following precautions should be followed:

– When storing the generator for short periods of

time make sure that the Ignition Switch, the Fuel

Valve and the Battery Switch are set in the OFF

position.

– When storing the generator for extended periods

of time make sure that the Ignition Switch, the

Fuel Valve and the Battery Switch are set in the

the the OFF position and the battery leads have

been disconnected from the battery.

DANGER

Page is loading ...

Champion 41533 Owner's Manual & Operating Instructions

Brand: Champion

Model: 41533

Category: Power generators

Type: Owner's Manual & Operating Instructions

Download PDF

report

Champion 41533 Owner's Manual & Operating Instructions

Champion 41533 Owner's Manual & Operating Instructions

Related papers

Other documents