ADE Reson8 Series Installation guide
- Category
- Flat panel accessories
- Type
- Installation guide
ADE Reson8 Series is a self-contained external sounder and strobe unit suitable for wall mounting. It features a 6-volt rechargeable Ni-Cad battery, a high-volume piezo sounder, and a blue prismatic strobe lens. The Reson8 Series also includes adjustable dual fail-safe cut-off timers, cover and wall anti-tamper protection, and twin status indicators.
ADE Reson8 Series is a self-contained external sounder and strobe unit suitable for wall mounting. It features a 6-volt rechargeable Ni-Cad battery, a high-volume piezo sounder, and a blue prismatic strobe lens. The Reson8 Series also includes adjustable dual fail-safe cut-off timers, cover and wall anti-tamper protection, and twin status indicators.
Features
¨
Self contained sounder & strobe unit
¨
6 volt rechargeable Ni-Cad battery
¨ 115db @ 1m
¨ High volume piezo driven sounder
¨ Twin status indicators
¨ Battery charge indicator
¨
Adjustable dual fail-safe cut-off timer
¨
Cover and wall anti-tamper protection
¨
Polycarbonate housing
¨
Blue prismatic strobe lens
These instructions cover the installation of Reson8 W/B -
white and blue unit (bell box), which is a self-contained
external sounder and strobe. The unit is suitable for wall
mounting externally and can be connected to any intruder
control panel. The dummy bell box has no functionality.
Technical Data
Operating voltage 10 - 15Vdc
Internal battery 6V Ni-Cd 280mAh
rechargeable
Quiescent current 50mA includes battery charge
current
Flash rate 80 - 140 per minute
Flash current 120mA at 12V
Sounder Output 115dB at 1m
Sounder current 240mA at 12V
Timer Test (5 seconds)
5, 10 and 20 minutes
Dimensions Height 291mm, Width 268mm,
Depth 69mm
Weight
Bell box
Dummy box
0.9kg
0.68kg
Housing
Lens
White Polycarbonate
Blue Polycarbonate
Part numbers Reson8 (White & Blue) - 8EP420
Reson8 (White & Blue) Dummy
box -8EP425
4188-831 issue 1_2/05_reson8 1
Installation instructions
Reson8 Bell Box
8EP420 (W/B) 8EP425 (W/B Dummy bell box)
Top keyhole fixing
Lid tamper and
wall tamper (not visible)
Links to set
Sounder duration
Link to select
continuous or
alternating status
LED indication
Bottom fixing
Bottom fixing
Presence of Hold off supply
Tamper healthy
Battery being charged
6V Ni-Cd Battery
280mAh
Strobe tube
Sounder
LED1
LED1
Link to enable (On) /
disable (Off) the battery
On Off
Battery
LED2
LED3
A
L
T
C
O
N
LEDs
J2
J1
(Red LED Indicator)
(Green LED Indicator)
(Red LED Indicator)
J6
J5
J3
J4
Test
20 minutes
5 minutes
10 minutes
TIMER SETTINGS
Wiring
Reson8 ADE Control
panel
Other control panel
STB- STROBE - - Strobe or -ST
TRIG- B - Bell -
HOLD OFF - A - Tamper supply -
HOLD OFF + D + Bell +
RTN- T - Tamper return -
BATTERY - Connect - from Reson8 battery
BATTERY + Connect + from Reson8 battery
Timer
The Reson8 will operate under normal
alarm conditions as directed by the
control panel. However, if the Reson8
is triggered into Self Activating Bell
mode (SAB), due to power loss or
cable damage, then the sounder will
operate from the Ni-Cad battery for the
set time. The minimum time setting is
marked as "TEST" which will limit the
bell to 5 seconds of operation.
"
After testing, please ensure that the timer is
correctly set to the desired position. The 20 minutes
duration is typical for most installation.
Status Indicators
The two LED indicators are used to display the status of the
Reson8. The red LED illuminates to indicate the hold off supply is
present. The green LED illuminates to show the there is no
tamper, that is the tamper circuit is closed and healthy.
The LED status indicators will operate in one of
two modes as a means of deterrent.
ALT: Alternating between Red & Green LED's
or CON: Red & green LED's are constantly
illuminated.
Battery Enable
Reson8 is supplied with a 6 Volt internal Ni-cad
battery, as part of the Self Activating Bell (SAB)
circuit. When commissioning the system you will
need to enable the battery in order to provide
battery back up in the event of mains supply
failure.
&
Note on connecting the battery link the
sounder will output tamper alarm.
Final Test
When installation is complete the Red (Hold Off Supply) LED
indicator should be illuminated. The green indicator will illuminate
when the lid is securely fixed into position.
We recommend that the following tests are then carried out:
¨
Test the operation of the sounder and the timer in
self-actuating mode, by removing the hold off supply to the
Reson8.
¨
Test the operation of the front cover tamper.
¨
Test the operation of the sounder and strobe, by generating
an alarm condition at the intruder control panel.
Installation Reson8
Novar Systems Limited reserves the right to revise this publication from time to time and make changes to the
content hereof without obligation to notify any person of such revisions of changes.
Hamilton Industrial Park, Waterside Road, Leicester LE5 1TN, UK Website: www.ade.co.uk
Telephone +44 (0) 116 246 2000 Fax (UK): +44 (0)116 246 2566
Registered office: Novar House: 24 Queens Road, Weybridge, Surrey KT13 9UX
2 4188-831 issue 1_2/05_reson8
-
STROBE
J6
+
TA
SCB
DB
BELL
+
-
SET
+ve
1A
BELL/STROBE
F5
Panel
Board
-
BATTERY
+
-
RTN
-
HOLD
OFF
+
-
TRIG
-
STB
Board
Reson8
-
BATTERY
+
-
RTN
-
HOLD
OFF
+
-
TRIG
-
STB
Board
Reson8
Green
Black
Red
Blue
Yellow
White
TDAB
TDAB
-
STROBE
J6
+
TA
SCB
DB
BELL
+
-
SET
+ve
1A
BELL/STROBE
F5
Panel
Board
-
BATTERY
+
-
RTN
-
HOLD
OFF
+
-
TRIG
-
STB
Board
Reson8
Green
Black
Red
Yellow
White
TDAB
J6
J5
J3
J4
Test
20 minutes
5 minutes
10 minutes
TIMER SETTINGS
A
L
T
C
O
N
LED
s
J
2
LED
3
(
Red
)
LED
2
(
Green
)
On Off
Battery
J1
-
1
-
2
ADE Reson8 Series Installation guide
- Category
- Flat panel accessories
- Type
- Installation guide
ADE Reson8 Series is a self-contained external sounder and strobe unit suitable for wall mounting. It features a 6-volt rechargeable Ni-Cad battery, a high-volume piezo sounder, and a blue prismatic strobe lens. The Reson8 Series also includes adjustable dual fail-safe cut-off timers, cover and wall anti-tamper protection, and twin status indicators.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
WONLEX KT13 Hard reset manual
-
Challenger AU1000WBX Engineer Manual
-
-
-
Risco ProSound Installation & Programming Manual
-
Cooper 9448ES Datasheet
-
Tamron TS690R User manual
-
-
Menvier Security TS700 Operating instructions
-
Pyronix DECIBELL Installation Instructions Manual
