Operator's Manual
Manuel d'utilisation
Libro de Instrucciones
Form No. 78484A 12/98 CLARKE TECHNOLOGY Printed in the U.S.A.
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your ALTO
machine could result in injury to you or to other personnel; damage to the machine or to other property
could occur as well. You must have training in the operation of this machine before using it. If you
cannot read English, have this manual explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator’s position at the rear of the machine.
For new books write to: ALTO U. S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.
PTV-15
E
Page -2- CLARKE TECHNOLOGY Operator's Manual PTV-15
Contents of this Book
Operator Safety Instructions .......................................................5
120V Instructions - Power Supply & Electrical Ground .............10
230V Instructions - Power Supply & Electrical Ground .............11
How to Prepare the Machine for Operation ..............................14
How to Operate the Machine ....................................................14
Routine Maintenance.................................................................16
SECTION II
Parts and Service Manual
Maintenance..............................................................................18
Head Assembly Drawing & Parts List PTV-15...........................20
Poly Tank Assembly Drawing & Parts List ................................21
Wet Vac Tools...........................................................................22
Model PTV-15
Capacity 15 gallons
Cord 28'
Hose 101"
Transport Wheels (2) 8"
Casters (2) 3"
Weight 58 lbs. shipping
weight
Page is loading ...
Page is loading ...
Page -5-
CLARKE TECHNOLOGY Operator's Manual PTV-15
OPERATOR SAFETY INSTRUCTIONS
WARNING AVERTISSEMENT ADVERTENCIA
DANGER: Failure to read and observe all DANGER statements could result in
severe bodily injury or death. Read and observe all DANGER
statements found in your Owner's Manual and on your machine.
WARNING: Failure to read and observe all WARNING statements could result in
injury to you or to other personnel; property damage could occur as
well. Read and observe all WARNING statements found in your
Owner's Manual and on your machine.
CAUTION: Failure to read and observe all CAUTION statements could result in
damage to the machine or to other property. Read and observe all
CAUTION statements found in your Owner's Manual and on your
machine.
DANGER: Failure to read the Owner's Manual prior to operating or attempting any service or
maintenance procedure to your ALTO machine could result in injury to you or to
other personnel; damage to the machine or to other property could occur as well.
You must have training in the operation of this machine before using it. If you or
your operator(s) cannot read English, have this manual explained fully before
attempting to operate this machine.
DANGER: Operating a machine that is not completely or fully assembled could result in injury
or property damage. Do not operate this machine until it is completely assembled.
Inspect the machine carefully before operation. Use only as described in this
manual. Use only Clarke Technology's recommended attachments.
DANGER: Machines can cause an explosion when operated near flammable materials and
vapors. Do not use this machine with or near fuels, grain dust, solvents, thinners,
or other flammable materials.
DANGER: Using a machine with a damaged power cord could result in an electrocution. Do
not use the machine if the power cord is damaged. Do not use the electrical cord
to move the machine. Keep cord away from heated surfaces. Do not unplug by
pulling on the cord; grasp the plug not the cord.
DANGER: Electrocution could occur if maintenance and repairs are performed on a unit that
is not properly disconnected from the power source. Disconnect the power supply
before attempting any maintenance or service.
WARNING: Operating a machine without observing all labels, decals, etc., could result in injury
or damage. Read all machine labels before attempting to operate the machine.
Make sure all of the labels are attached or fastened to the machine. Get replace-
ment labels and decals from your Clarke Technology distributor.
WARNING: Electrical components can "short-out" if exposed to water or moisture. Keep the electri-
cal components of the machine dry. Always store the machine in a dry building.
WARNING: Use of this machine to move other objects or to climb on could result in injury to the
operator or damage to the machine. Do not use this machine as a step or furniture. Do
not allow to be used as a toy. Close attention is necessary when used by or near
children.
WARNING: Moving parts of this machine can cause injury and/or damage. Keep hands, feet, loose
clothing, hair, fingers, and all parts of the body away from openings and moving parts.
Page -6- CLARKE TECHNOLOGY Operator's Manual PTV-15
WARNING: Electrocution could occur if you handle the plug or appliance with wet hands. Do not
handle plug or appliance with wet hands.
WARNING: Damage could occur to machine if openings are blocked. Do not put any object into
openings. Do not use with any opening blocked; keep free of dust, lint, hair, and
anything that may reduce air flow.
WARNING: Injury could occur to the operator or the machine if used without the dust bag and/or
filters. Do not use the machine without the dust bag and/or filters in place (DTV-7 only).
WARNING: Injury to the operator and/or damage to the machine could occur when cleaning on stairs,
unless extra caution is used. Use extra caution when cleaning on stairs.
WARNING: To prevent possible electrical shock, always use a 3-wire electrical system connected to
the electrical ground. See "Grounding Instructions".
WARNING: To reduce the risk of fire, electric shock, or injury:
• Do not leave appliance when plugged in. Unplug from outlet when not in use and
before servicing.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or
hot ashes.
• Turn off all controls before unplugging.
INSTRUCCIONES DE SEGURIDAD PARA EL OPERADOR
PRECAUCION AVERTISSEMENT ADVERTENCIA
PELIGRO: Ignorar o no considerar los informes sobre PELIGRO le puede
causar a Vd. o a otras personas del personal severas heridas en
el cuerpo o incluso la muerte. Lea y préstele atención a todas las
señales de PELIGRO encontradas en este Manual del Propietario
y en su máquina.
ADVERTENCIA: Si se ignoran o no se toman en cuenta las informaciones sobre
ADVERTENCIA encontradas en su máquina o en este Manual del
propietario, Vd. u otras personas pueden resultar con heridas;
también pueden ocurrir daños en otras partes del edificio donde
trabaja. Lea y préstele atención a todas las señales de
ADVERTENCIA encontradas en este Manual del propietario y en
su máquina.
PRECAUCION: Si Ud. ignora o no le presta atención a todas las señales de
PRECAUCION puede causarle daño a la máquina o a otras cosas.
Lea y préstele atención a todas las señales de PRECAUCION
encontradas en su Manual del propietario y en su máquina.
PELIGRO: Si no lee el Manual del propietario antes de operar o tratar de realizar cualquier
servicio o procedimiento de mantenimiento a su máquina ALTO, puede
causarse una herida a Ud. mismo o a otros miembros del personal; también
puede ocurrir un daño en la máquina u otro objeto. Ud. debe entrenarse en la
operación de la máquina antes de usarla.
PELIGRO: El operar una máquina que no esté totalmente ensamblada puede producir
heridas o daños en la propiedad. No opere esta máquina hasta que esté
totalmente ensamblada. Inspeccione la máquina cuidadosamente antes de
operarla. Usela sólo como se describe en este manual. Use sólo los
accesorios recomendados por Clarke Technology.
Page is loading ...
Page is loading ...
Page is loading ...
Page -10- CLARKE TECHNOLOGY Operator's Manual PTV-15
120 VOLT MACHINE
INSTRUCTIONS FOR CONNECTION
TO THE POWER SUPPLY
AND THE ELECTRICAL GROUND
This machine must be connected to the electrical
ground to protect the operator from electric shock.
The machine has an approved power cord with three
conductors and a plug with three terminals. Connect
the plug to a receptacle that has three holes and is
connected to the electrical ground. The green (or
green and yellow) conductor in the cord is the ground
wire. Never connect this wire to any terminal other
then the ground terminal.
This machine uses a 120 volt AC 60 cycle electrical
circuit. Make sure you have the correct frequency and
voltage before connecting the power cord to an outlet.
The machine has a plug as shown in Figure 1. If a
receptacle connected to the electrical ground as
shown in Figure 1 is not available, have one installed
by an electrical contractor. Do not use an adapter.
WARNING: To prevent possible electric shock,
protect the machine from rain. Keep
the machine in a dry building.
WARNING: To prevent possible electric shock,
always use a 3-wire electrical system
connected to the electrical ground.
WARNING: Do not cut, remove or break the ground
pin. If the outlet does not fit the plug,
consult your electrical contractor.
WARNING: Have worn, cut or damaged cords and
plugs replaced by an authorized ser-
vice person.
Figure 1
Tornillo de
la tapa
El toma
corriente
debe estar
conectado al
polo de tierra.
Terminal de tierra.
Figura 2
Plate
Screw
Outlet must be
connected to
the electrical
ground
Ground Pin
Vis de fixation
La prise doit
étre reliée à
la terre.
Broche de terre
Figura 3
Page is loading ...
Page -12- CLARKE TECHNOLOGY Operator's Manual PTV-15
230 VOLT MACHINE
INSTRUCTIONS FOR CONNECTION
TO THE POWER SUPPLY
AND THE ELECTRICAL GROUND
This machine must be connected to the electrical
ground to protect the operator from electric shock.
The machine has an approved power cord with two
main conductors and one earthing conductor. Connect
the plug to a receptacle as shown in Figure 4. The
green (or green and yellow) conductor in the cord is the
ground wire. Never connect this wire to any terminal
other then the ground terminal.
Make sure you have the correct frequency and voltage
before connecting the power cord to an outlet. The
machine has a plug as shown in Figure 4. If a
rec1eptacle connected to the electrical ground as
shown in Figure 4 is not available, have one installed
by an electrical contractor. Do not use an adapter.
WARNING: This machine will operate only
on AC frequency and electrical
voltage shown on the name-
plate. Make sure you have the
correct frequency and voltage
before connecting the power
cord to an outlet. If you are not
sure, consult your electrical
contractor.
WARNING: Have worn, cut or damaged
cords and plugs replaced by an
authorized service person.
After using this machine, follow these instructions:
- Store the cord on the hook.
- Store the machine indoors away from sources
of heat.
This machine is provided with an automatically reset
thermal overload to avoid damage to the motor. If the
thermal overload stops the motor unplug the machine
and follow the procedures below:
- Empty the vacuum tank.
- Shake the filter bag to remove dust.
- In a few minutes the thermal overload will
allow restarting of the motor.
Figure 4
Pin Earthing Contacts
Side Earthing Contacts
European Plug
Figura 5
Contacto del terminal de tierra.
Contactos laterales de tierra.
Enchufe europeo.
Figure 6
Broche de mise á la terre
Encoches latérales pour mise á la terre
Fiche Européene
Page is loading ...
Page -14- CLARKE TECHNOLOGY Operator's Manual PTV-15
HOW TO PREPARE THE MACHINE
FOR OPERATION
Introduction: This machine is a commercial vacuum
that is used to remove either liquid or dry material from a
surface. The material flows into a tank and is held in the
tank.
Instructions for Connection to the Power Supply
This machine uses a 110 to 120 volt AC 50/60 cycle
electrical circuit. Make sure you have the correct
frequency and voltage before connecting the power cord
to an outlet.
WARNING: Replace any worn, cut, or damaged
cords. Replace any damaged plugs,
receptacles, or connector bodies.
WARNING: Do not move the machine over an
electrical cord. Always lift the cord
over the machine.
Extension Cords
This machine has a power cord with wire sizes 16 AWG
(AWG means American Wire Gauge).
WARNING: If you use an extension cord, use an
extension cord with minimum wire
size 16 AWG.
HOW TO OPERATE THE MACHINE
The start/stop switch is on the head of the machine.
See figure 7. To start the machine, put the switch in
the "O" position. Stop the motor and remove the
electrical plug from the electrical outlet when you clean
the tank and filters.
For liquid operation, remove the filter bag. This machine
has a float shut-off valve. When the liquid raises the
float, the air stops moving through the machine. Re-
move the liquid from the tank. For the operation, use
only low-foaming or non-foaming detergents.
For dry operation, use the filter bag. Stop the machine
and remove the dirt from the tank when the efficiency of
the machine decreases. Remove the dust from the filter
bag each time you remove the dirt from the tank.
Frequently check and clean the filter bag. Use a brush
to clean the filter bag.
For shampooing (dry foam) the carpet, use a filter bag.
Stop the machine when the efficiency of the machine
decreases. Remove the foam, liquid, dirt and carpet
fibers from the tank and the filter bag. When necessary,
stop and dry the filter bag, or use a new bag.
Figure 7
The Start/Stop Switch
Figura 7 : interruptor arranque / parada.
Figure 7 : interrupteur marche/arrêt
Page is loading ...
Page -16- CLARKE TECHNOLOGY Operator's Manual PTV-15
ROUTINE MAINTENANCE
Keep the machine clean. It will have longer life and
need fewer repairs.
WARNING: To prevent electrical shock, always
remove the electrical plug from the
electrical outlet before doing any
repairs or maintenance to this
machine.
How to Clean the Filter Bag:
To clean the filter bag, follow this procedure:
1. Lift the clamps on each side of the machine.
See Figure 8.
2. Remove the cover.
3. Lift the cloth filter bag. See figure 9.
4. Shake the filter to remove the dirt.
5. Brush the filter to remove the embedded dirt.
6. Remove the dirt from the tank.
7. Put the cloth filter in the tank.
8. Set the cover on the tank.
9. Put the brackets over the cover rim.
10. Push both clamps down.
Figure 8
Figure 9
MAINTENANCE
Veillez toujours à ce que la machine soit propre. Ceci
augmentera sa durée de vie et diminuera le nombre
de réparations.
!AVERTISSEMENT!: Pour éviter tout risque de
choc électrique, débrancher
toujours la fiche de la prise
réseau avant d’effectuer
toute réparation ou toute
opération de maintenance
sur cette machine.
Nettoyage du sac-filtre
Pour nettoyer le sac-filtre, suivre les instructions ci-
après :
1. Soulever les poignées de verrouillage latérales.
Voir figure 2.
2. Enlever le couvercle.
3. Soulever le sac-filtre en tissu. Voir figure 3.
4. Secouer le filtre pour faire tomber les
poussières.
5. Brosser le filtre pour nettoyer les parois.
6. Nettoyer le réservoir.
7. Replacer le sac-filtre dans le réservoir.
8. Replacer le couvercle sur le réservoir.
9. Replacer les crochets sur le bord du couvercle
10. Rabattre les deux poignées de verrouillage
latérales.
MANTENIMIENTO
Compruebe siempre que la máquina es limpia. Alargará
así la vida útil de la máquina y las reparaciones serán
menos frecuentes.
¡AVISO! Para evitar el peligro de choque eléctrico,
desconecte siempre el enchufe de la red
antes de realizar un mantenimiento o una
reparación de la máquina.
Limpieza de la bolsa-filtro
Para limpiar la bolsa-filtro, siga las instrucciones
siguientes:
1. Levante las empuñaduras de bloqueo laterales.
Véase figura 2.
2. Quite la tapa.
3. Levante la bolsa-filtro de tejido. Véase figura 3.
4. Sacude el filtro para quitar el polvo.
5. Cepille el filtro para limpiar las paredes.
6. Limpie el depósito.
7. Vuelva a colocar la bolsa-filtro en el depósito.
8. Vuelva a colocar la tapa sobre el depósito.
9. Vuelve a colocar los ganchos sobre el borde de
la tapa.
10. Abate las dos empuñaduras de bloqueo
laterales.
Page -17-
CLARKE TECHNOLOGY Operator's Manual PTV-15
PTV 15
Section II
Parts and Service Manual
(78484A)
Page -18- CLARKE TECHNOLOGY Operator's Manual PTV-15
MAINTENANCE
This section describes the procedure that must be
done by a person authorized to do maintenance.
WARNING: To prevent electrical shock, always
remove the electrical plug from the
electrical outlet before doing any
repairs or maintenance to this ma-
chine.
Keep the machine clean. It will have longer life and
need fewer repairs.
Maintenance of the Motor
The motor that has a commutator and carbon brushes
must be checked every six months or 600 hours or
operation.
WARNING: Electrical inspections must be made
by a person authorized to do mainte-
nance. Electrical repairs must be
made by a person authorized to make
electrical repairs.
How to Check the Commutator and Carbon Brushes
To check the commutator and the carbon brushes, follow
this procedure:
1. Remove the screw that holds the motor cover.
2. Disconnect the wires.
3. Push the motor through the bottom of the plate.
4. Inspect the commutator. Take the machine to a
Clarke Technology authorized repair location if
you see any of the following conditions:
a. Small holes in th surface of the commutator.
See figure 1A.
b. Uneven color. Look for an even dark brown
color. Clean areas indicate a problem. See figure
1B.
c. High mica. The mica insulation must be lower
than the commutator bars. See figure 1C.
5. Remove the carbon brush assemblies and check
the carbon brushes. Replace both carbon brush
assemblies if either of the carbon brushes is
shorter than ½ inch (13mm), order two new brushes
and replace both carbon brushes earlier than the
normal inspection time.
6. Install the motor cover, and the fasteners.
WARNING: The machine must be tested for
electrical safety after electrical repairs
are made.
NOTE: For best operation, have the machine checked
by a Clarke Technology authorized repair person every
12 months.
For safe operation and longer life of your Clarke
Technology product, use Clarke Technology parts.
Figure 1
Figure 2
Figure 3
Good
A
Small
Holes
Good
B
Uneven
Good
High
Mica
C
Bueno
A
Pequeños
agujeros
Coloración
desigual
Bueno
B
Bueno
Demasiado
pico
C
Bon
A
Petits
trous
Bon
B
Coloration
inégale
C
Trop de
Mica
Bon
Page is loading ...
Page -20- CLARKE TECHNOLOGY Operator's Manual PTV-15
CLARKE TECHNOLOGY PTV-15
Head Assembly Drawing & Parts List 12/98
CLARKE TECHNOLOGY PTV-15
Filter Bag & Float Assembly Drawing & Parts List 1/98
1
2345678
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
1
2
3
4
5
6
7
8
Ref. Part No. Description Qty
1 51841A Cord, Power 1
2 56448A Strain Relief 1
3 54503A Grip, Cord 1
4 56441A Screw 5mm x 20mm 2
5 50522A Block Terminal 1
6 51842A Hook, Cord 1
7 56481A Screw, 5mm x 30mm 4
8 54914A Handle, Lift 1
9 56482A Screw, 5mm x 35 mm 2
10 56482A Screw, 5mm x 35 mm 2
11 51843A Cover, Dome 1
12 47316B Switch, Rocker 1
13 56441A Screw, 5mm x 20mm 4
14 54064A Filter, Upper 1
15 56482A Screw, 5mm x 35mm 6
16 51844A Cover, Motor 1
17 57877A Ring, Vac Motor 1
18 54063A Filter, Motor 1
19 56483A Screw, 5mm x 40 mm 6
20 56441A Screw, 5mm x 20 mm 4
21 56484A Support, Motor 1
22 54377A Gasket, Vac Motor 1
23 59859A Washer, Star 1
24 56485A Screw, 4mm x 8mm 1
25 56039B Motor, Vac 115V 1
56046B Motor, Vac 230v 1
40834A Brush, Carbon 115V 1
40835A Brush, Carbon 230V 1
26 54377A Gasket, Vac Motor 1
27 57876A Ring, Lower 1
28 50532A Base, Motor 1
29u 54346A Gasket, Head Asm. 1
NOTE: u indicates a changes has been made sincle
last publication of this manaul.
Ref. Part No. Description Qty
1 58541A Spacer, Plastic 4
2 58411A Screw, 5mm x 25mm 4
3 57856A Cage, Float 1
4 58073A Screen, Filter 1
5 53981A Float 1
6 57848A Ring, Support 1
7 50720A Bag, Filter 1
8 56492A Support, Bag 1
28
To add optional filters for PTV-15 order:
54015A Filter, HEPA 1 and 57372A Retainer 1
or
53982A Filter, Cartridge 1 and 57372A Retainer 1
29
Page -21-
CLARKE TECHNOLOGY Operator's Manual PTV-15
CLARKE TECHNOLOGY PTV-15
Poly Tank & Carriage Drawing & Parts List 1/98
Ref. Part No. Description Qty
1 54915A Handle, Transport Poly 1
2 58922A Tank, Poly 15 Gallon 1
3 56481A Screw, 5mm x 30mm 4
4 54345A Gasket, Hose Adapter 1
5 54376A Gasket, Tank Adapter 1
6 53166A Deflector, Tank 1
7 50337A Adapter, Hose 1
8 57376A Rivet 4
9 51823A Clamp, Tank 2
10 56482A Screw, 5mm x 35mm 8
11 87055A Washer 8
12 56491A Support, Handle 2
13 56490A Support, Handle Middle 2
14 57374A Rivet 2
15 52120A Caster, Swivel 2
16 56489A Screw, 4mm x 15mm 8
17 56488A Support, Axle 2
18 59939A Wheel, Transport 2
19 57379A Retainer, Wheel 2
20 52067A Cap, Hub 2
21 58525A Spacer, Wheel 2
22 56441A Screw, 5mm x 20mm 8
23 50143A Axle, Wheel 1
24 56289A Nut, Pipe 1
25 54344A Gasket, Tank 1
26 50203A Adaptor, Drain 1
27 722030 Clamp, Hose 1
28 54888A Hose, Drain 1
29 58413A Screw, 5mm x 20mm 1
30 51846A Clamp, Hose 1
31 56487A Support, Drain Plug 1
32 57143A Plug, Drain Hose 1
Ref. Part No. Description Qty
123456
8
7
9
11
10
12
14
13
15
16
17
18
19
20
212223
24
25
26
27
28
29
30
31
32
Page -22- CLARKE TECHNOLOGY Operator's Manual PTV-15
CLARKE TECHNOLOGY PTV-15
Wet Vac Tools Parts List 6/97
Part No. Description
55382A Tool Kit
59213B Tool, Squeegee
59214B Tool, Floor Brush
59215A Tool, Crevice 38mm
57503A Reducer, Wand
59860A Wand, Extension 2 Pc.
59861A Wand, Chrome 2 Pc.
54887A Hose, 38mm 2.5m
Ref. Part No. Qty Description
1 50753A 1 Body, Tool
2 57873A 1 Ring, Floor Tool
3 50357A 1 Adapter, Floor Tool
4 53096A 2 Support, Floor Tool
5 88001A 4 Screw, 5mm x 15mm
6 59970A 2 Wheel & Axle
7 53097A 2 Squeegee Blade
Squeegee Tool - 59213B
CLARKE TECHNOLOGY PTV-15
Squeegee Tool Drawing & Parts List 12/97
1
23
6
54
7
Ref. Part No. Qty Description
1 50753A 1 Body, Tool
2 57873A 1 Ring, Floor Tool
3 50357A 1 Adaptor, Floor Tool
4 53096A 2 Support, Floor Tool
5 88001A 4 Screw, 5mm x 15mm
6 59970A 2 Wheel & Axle
7 51716A 1 Brush Guide
8 51717A 1 Brush Strip, Serrated
Floor Brush Tool - 59214B
CLARKE TECHNOLOGY PTV-15
Floor Brush Tool Drawing & Parts List 12/97
1
2
3
6
54
7
8
Page -23-
CLARKE TECHNOLOGY Operator's Manual PTV-15
ALTO
®
PRODUCT SUPPORT BRANCHES
PRODUCTION FACILITIES
ALTO Danmark A/S, Aalborg
Blytaekkervej 2
DK-9000 Aalborg
+45 72 18 21 00
ALTO Danmark A/S, Hadsund
Industrikvarteret
DK-9560 Hadsund
+45 72 18 21 00
SALES SUBSIDIARIES
ALTO Canada Ltd., Rexdale Ontario
24 Constellation Ct.
(416) 675-5830
ALTO Overseas Inc., Sydney (Australia)
1B/8 Resolution Drive
Caringbah NSW 2229
+61 2 9524 6122
ALTO Cleaning Systems Asia Pte Ltd., Singapore
No. 17 Link Road
Singapore 619034
+65 268 1006
ALTO Deutschland GmbH, Frondenberg (Germany)
Ardeyer Str. 15
D-58730 Frondenberg
+49 2373 754 200
ALTO Cleaning Systems (UK) Ltd., Penrith
Gilwilly Industrial Estate
Penrith
Cumbria CA11 9BN
+44 1768 868 995
ALTO France S.A. Strasbourg
B.P. 44, 4 Place d’Ostwald
F-67036 Strasbourg
Cedex 2
+33 3 8828 8400
ALTO Nederland B.V. Vianen
Stuartweg 4C
NL-4131 NJ Vianen
+31 347 324000
ALTO Sverige AB, Molndal (Sweden)
Aminogatan 18
Box 4029
S-431 04 Molndal
+46 31 706 73 00
ALTO Norge A/S, Oslo (Norway)
Bjornerudveien 24
N-1266
+47 2275 1770
CLARKE TECHNOLOGY
AMERICAN SANDERS TECHNOLOGY
A.L. COOK TECHNOLOGY
Customer Service Headquarters and Factory
2100 Highway 265
Springdale, Arkansas 72764
(501) 750-1000
Technical Service
1-800-356-7274
U. S. A. Locations European Locations
HEAD OFFICE
ALTO U.S. Inc., St. Louis, Missouri
16253 Swingley Ridge Road, Suite 200
Chesterfield, Missouri 63017-1725
PRODUCTION FACILITIES
ALTO U.S. Inc., Springdale, Arkansas
2100 Highway 265
Springdale, Arkansas 72764
(501) 750-1000
Customer Service - 1-800-253-0367
Technical Service - 1-800-356-7274
ALTO U.S. Inc., Bowling Green, Ohio 43402
1100 Haskins
ALTO U.S. Inc., Clearwater, Florida 33765
1500 N. Belcher Road
SERVICE FACILITIES
ALTO U.S. Inc., Carlstadt, New Jersey 07072
150 Commerce Road
(201) 460-4774
ALTO U.S. Inc., Elk Grove, Illinois 60007
2280 Elmhurst Road
(847) 956-7900
ALTO U.S. Inc., Denver, Colorado 80204
1955 West 13th Ave.
(303) 623-4367
ALTO U.S. Inc., Houston, Texas 77040
7215 North Gessner Road
SALES AND SERVICE FACILITIES
ALTO U.S. Inc., Madison Heights, Michigan 48071-0158
29815 John R.
(810) 544-6300
ALTO U.S. Inc., Marietta, Georgia 30062
1355 West Oak Common Lane
(770) 973-5225
Page -24- CLARKE TECHNOLOGY Operator's Manual PTV-15
CLARKE TECHNOLOGY WARRANTY
This ALTO Industrial/Commercial Product is warranted to be free from defects in materials and workmanship
under normal use and service for a period of one year from the date of purchase, when operated and maintained in
accordance with Clarke Technology's Maintenance and Operations Instructions.
This warranty is extended only to the original purchaser for use of the product. It does not cover normal wear
parts such as electrical cable, rubber parts, hoses and motor brushes.
If difficulty develops with the product, you should:
(a). Contact the nearest authorized Clarke Technology repair location or contact the ALTO, CLARKE TECHNOL-
OGY Service Operations Department, 2100 Highway 265, Springdale, Arkansas 72764, for the nearest autho-
rized Clarke Technology repair location. Only these locations are authorized to make repairs to the product under
this warranty.
(b). Return the product to the nearest Clarke Technology repair location. Transportation charges to and from the
repair location must be prepaid by the purchaser.
(c). Clarke Technology will repair the product and/or replace any defective parts without charge within a reason-
able time after receipt of the product.
Clarke Technology's liability under this warranty is limited to repair of the product and/or replacement of parts
and is given to purchaser in lieu of all other remedies, including INCIDENTAL AND CONSEQUENTIAL DAM-
AGES.
THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE SPECIFIED HEREIN. THERE ARE NO
WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION OF THE FACE HEREOF. NO WARRANTIES,
INCLUDING BUT NOT LIMITED TO WARRANTY OF MECHANTABILITY, SHALL BE IMPLIED. A warranty
registration card is provided with your Clarke Technology product. Return the card to assist Clarke Technology in
providing the performance you expect from your new floor machine.
ALTO, 2100 Highway 265, Springdale, Arkansas 72764.
CLARKE TECHNOLGOY reserves the right to make changes or
improvements to its machine without notice.
Always use genuine Clarke Technology Parts for repair.
CLARKE TECHNOLOGY
2100 Highway 265
Springdale, Arkansas, 72764
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Alto PTV-15 Manuel utilisateur
- español: Alto PTV-15 Manual de usuario