American Standard 2900.SERIES User manual

Brand: American Standard

Model: 2900.SERIES

Category: Sanitary ware

Type: User manual

This manual is also suitable for

2800.SERIES

US60359E

2900.SERIES

2800.SERIES

Certified to comply with ANSI A112.18.1M

Required Tools

*Supplied with Fitting

*Hex key

RECESS

Turn off hot and cold water supplies before beginning.

CAUTION

Insert SPOUT SHANK (1) through center hole of MOUNTING LEDGE.

Make sure that the RUBBER RING (2) is properly seated in RECESS

at base of SPOUT (3).

Assemble RUBBER WASHER (4) and BRASS WASHER (5) onto

SHANK (1). From underside of ledge secure SPOUT (3) into position

with LOCKNUT (6).

SPOUT ASSEMBLY

PREPARE TUBE AND TEE ASSEMBLY

Prepare TUBE and TEE ASSEMBLY (1) to fit center to center

VALVE (2) location (between 6-1/2" and12"). If necessary,

cut and/or bend TUBING carefully. Make sure tube bend is

close to the TEE (1) so that it will not effect the compression

joint at the VALVE CONNECTION.

Remove COUPLING NUT (3) and FERRULE (4) from each

VALVE (2) and slide onto TUBING (5).

ADJ. 6-1/2 TO 12

Flat Blade Screwdriver

Adjustable Wrench

Channel Locks

MOUNTING

LEDGE.

VALVE inlet is 3/4-inch NPT male connector.

NOTE

1-1/4

MAX.

(H)

(C)

1-1/8 D.

3/4-14 MALE

N.P.T. INLETS

MOUNTING

SURFACE

ADJ. 6-1/2 TO 12

2-3/8D.

3 D.

1-1/16 D.

3-3/8

ROUGHING-IN DIMENSIONS

MOUNTING

SURFACE

2-3/8D.

3 D.

3-3/8

3-13/16

7-3/4

6-1/2

DECK-MOUNT BATH FILLER

Installation

Instructions

Williamsburg

Thank you for selecting American-Standard...the benchmark of

fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please

read these instructions carefully before you begin.

8-1/2

2-1/4

4-1/4

RECESS

US60359E

To change direction of handle rotation,

proceed as follows:

Turn valve to OFF position.

Pull out INDEX CAP (6) and remove

HANDLE SCREW (5).

Pull off HANDLE (4) and unscrew porcelain

ESCUTCHEON BASE (3).

Remove ADAPTER (1) and SPRING CLIP (9).

Lift STOP WASHER (8), turn 90˚ and replace.

Replace SPRING CLIP (9).

Reinstall ESCUTCHEON (3) and HANDLE

ASSEMBLY.

If spout drips, operate handles

several times from OFF to ON

position. Do not force -

handles turn only 90˚.

90˚

SERVICE

INSTALL HANDLES

Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)

into mounting holes from underside of ledge.

Push COUPLING (8) into TEE (5). Press TEE (5) onto SPOUT SHANK (6) making

certain that the O-RING (7) is properly seated on SHANK (6). Thread

COUPLING (8) firmly onto SPOUT SHANK (6).

Install MOUNTING NUT (1) onto valve shanks.

Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto

valves until snug against internal stop.

Tighten MOUNTING NUT (1) to secure VALVE (4) position.

Slide FERRULE (12) and COUPLING NUT (2) to outlet of VALVE (4) and tighten

COUPLING NUT (2) firmly.

Connect HOT water supply to inlet of left VALVE and COLD water supply to

inlet of right VALVE using appropriate connector.

VALVE ASSEMBLY

HOT

COLD

MOUNTING

SURFACE

TOP

Figure "A"

SPLINE END DOWN

Push INDEX CAP (6) in hole of LEVER BALL (4).

Secure LEVER BALL (4) with HANDLE SCREW (5).

Find correct position of HANDLE (4) by adjusting male teeth on

ADAPTER (1) to female teeth in LEVER BALL (4).

Thread HANDLE BASE (3) onto VALVE ESCUTCHEON (7)

Push LEVER BALL (4) onto ADAPTER (1).

Push ADAPTER (1) on VALVE STEM (2), so that the hole of the

ADAPTER (1) without spline is facing up. See figure "A".

Threads of VALVE BODY (4) should extend at least 5/16 inch above MOUNTING

SURFACE (11). If necessary, adjust MOUNTING NUT (1).

5/16'' MIN.

MOUNTING SURFACE

INSTALLATION OF OPTIONAL METAL LEVER HANDLES

(Supplied with Faucet)

Thread PORCELIAN LEVER HANDLE (2) counter-clockwise

and remove INDEX BUTTON with MOUNTING ROD ASSEMBLY (1),

HANDLE COLLAR (4) and O-RING (5).

Insert MOUNTING ROD ASSEMBLY (1) into METAL HANDLE (3),

HANDLE COLLAR (4) and O-RING (5).

Thread HANDLE ASSEMBLY (6) into ball of

HANDLE BASE (7). Apply pressure to the

MOUNTING ROD ASSEMBLY (1) while

turning the HANDLE COLLAR (4), in order to

tighten firmly.

US60359E

Williamsburg

028679-0070A

TUBE & TEE

ASSEMBLY

028698-0070A

COUPLING

013314--YYY0A

SPOUT END

DECK-MOUNT

BATH FILLER

012668-0070A

SHANK KIT

030274-0070A

SHANK

MOUNTING KIT

911903-0070A

RUBBER RING

012078-0070A

VALVE COUPLING KIT

030216-YYY0A

BUTTON &

SCREW SET

030216-YYY0A

BUTTON &

SCREW SET

CHROME 002

Replace the "YYY" with

appropriate finish code

994053-0070A

VALVE

051379-YYY0A

VALVE

ESCUTCHEON KIT

918428-0070A

HANDLE SCREW

021470-YYY0A

INDEX CAP

051381-YYY0A

HANDLE BASE

909410-YYY0A

LEVER BALL

918049-0070A

HANDLE ADAPTER

911903-0070A

RUBBER RING

907971-YYY0A

SPOUT ESCUTCHEON

907971-YYY0A

SPOUT ESCUTCHEON

013318-YYY0A

SPOUT KIT

051383-YYY0A

SPOUT KIT

MODEL NUMBER

M906617-0070A

MOUNTING NUT

028678-YYY0A

STREAM

STRAIGHTENER

SPOUT

(2900. SERIES)

SPOUT

(2800. SERIES)

2800.SERIES

2900.SERIES

BRASS

099

060353-YYY0A

PORCELAIN

LEVER HANDLE

060354-YYY0A

METAL

LEVER HANDLE

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH

A COARSE SURFACE.

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1-800 442-1902

Weekdays 8:00 a.m. to 8:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc.

IN MEXICO 01-800-839-12-00

American Standard 2900.SERIES User manual

Brand: American Standard

Model: 2900.SERIES

Category: Sanitary ware

Type: User manual

This manual is also suitable for

2800.SERIES

Download PDF

report

American Standard 2900.SERIES User manual

This manual is also suitable for

American Standard 2900.SERIES User manual

Related papers

Other documents