C2G 26846 Owner's manual

C2G
Brand
C2G
Model
26846
Category
Cable network testers
Type
Owner's manual

This manual is also suitable for

This manual covers the following models
256652/LB
256652/LBT
256652/IDT
256652/TK
256652/TFK
User Manual
Remote Network Cable Tester
TM
Pro
LANtest
LANtest Pro
LANtest Pro with tone generator
LANtest Pro with tone generator and 4 remote IDs
LANtest Pro with 256712A Probe
LANtest Pro with 256712F Probe
Contents Page
1. Introduction 1
2. Features 1
3.
4.
.
.
5
. Product Profile 5
11. Fault Status 8
. Battery Replacement
. Warning
LANtest Pro
LANtest Pro Specifications 2
LANtest Pro Cable Test Operation 3
5 LANtest Pro Tone Generator Operation 3
6 LANtest Pro Remote ID Operation 4
7. Probe Features 4
8. Probe Specifications
9. Probe Operation 5
10
Introduction
Congratulations on your purchase of the LANtest Pro
network cable tester series! The LANtest Pro is a small
hand-held cable tester, which enables network professionals
to quickly and easily verify the integrity of Ethernet twisted
pair cables. In one step, the LANtest Pro will test twisted
pair cables for open pairs, shorted pairs, reversed pairs,
crossed pairs and split pairs. Just push the TEST button, and
the LANtest Pro will automatically scan for any existing
faults in your cable. The specially designed remote
terminator is provided for one-person testing of installed
cables. The tone generator function can be used to send a
signal through your installed cables which can be traced with
the Probe or any cable tracer in the market.
Package Contents:
For 256652/IDT & 256652/LBT Users can buy 256712A or
256712F to Upgrade the tone function
Item Number Remotes Manual Soft carry case Probe Probe with filter
256652/LB
256652/LBT
1 Y Y N N
1 Y Y N N
4 Y Y N N
1 Y Y Y N
1 Y Y Y Y
256652/IDT
256652/TK
256652/TFK
LANtest Pro Features
Tests for wiring faults of open, short, reversed, crossed and
split pairs
Split pair fault detection at a minimum 40cm cable length
Testing of twisted pair cables to over 450ft
Tone generator for tracing installed cables and locating
faults (available on models 256652/LBT, 256652/TK,
256652/TFK and 256652/IDT)
Identification of up to 4 remote termination units (available
1
1
1
2
3
3
4
4
5
5
5
8
9
9
on model 256652/IDT)
Verification of shield integrity
Cross talk detection in excess of 3dB + 0.3dB at 3.5Mhz
between any two pairs
Specially designed remote unit that enables one person to
test installed cables
Easy to read fault display and high speed testing
Debug mode for detailed fault identification results
Auto sleep mode and power off switch to decrease power
consumption
LANtest Pro Specifications
Connectors
LANtest Pro Main Unit RJ45 jack
Remote Unit RJ45 jack
Pairs tested
1/2, 3/6, 4/5, 7/8 and shield
LED display
Horizontal: 5 Green LEDs for pair and shield display
(1-2, 3-6, 4-5, 7-8 and shield)
TONE G. LED (for models 256652/LBT, 256652/TK,
256652/TFK and 256652/IDT)
Vertical: 5 Red LEDs for fault display and #ID display
(OPEN, SHORT, REVERSED, MISWIRE,
SPLIT PAIRS and LOW BATTERY)
For 256652/IDT the fault display shares with the #ID
Display (#1, #2, #3, #4)
Cable test length limit
Minimum: 0.4m Maximum: Over 200m
Power:
LANtest Pro: 6V alkaline DC battery
Remote identifier: No battery required
Dimensions:
LANtest Pro: 125 x 52 x 30 mm (L x W x H)
Low battery indicator
LANtest Pro Cable Test Operation:
1.Select "Cable" position on the toggle switch.
2.Plug one end of the subject cable into the RJ45 jack on
the master unit and the other end into the RJ45 jack on
the remote terminator.
Note: The remote terminator can be slipped and locked into the
master unit for convenient testing of patch cables.
3.Push the test button and check the results: First, check
the 5 horizontally aligned green LED indicators (1-2, 3-
6, 4-5, 7-8, SHIELD) for integrity status:
Solid light : pair is OK
Flashing light : pair is faulty
No light : open pair
a. Simultaneously, check the 5 vertically aligned LED
indicators (SHORT, REVERSED, MISWIRE, SPLIT
PAIRS) for the wiring faults.
b. For more detailed information about what faults are
occurring in which pairs, hold the TEST button for 2
seconds to activate "Debug mode." The tester will test
each pair one by one, pausing briefly on each pair, and
display the corresponding fault status.
LANtest Pro Tone Generator Operation (only
available on models 256652/LBT, 256652/TK,
256652/TFK and 256652/IDT):
1. Slide the toggle switch on the LANtest Pro to the "Tone"
position
2. Quickly press the TEST button once for continuous tone
mode, or hold down for two full seconds for warble tone
2 3
mode. To change modes, switch tester off and restart.
3. Using switch on side of Probe, select "speaker mode,"
"LED mode" or "speaker & LED mode."
4. Use the Probe or any cable tracer to trace the subject
wire. Reception of tone will be loudest (amplifier) or
brightest (LED) on the subject wire.
LANtest Pro Remote ID Operation (available on
model 256656/IDT)
1. Select "Cable" position on the toggle switch.
2. Plug one end of the subject cable into the RJ45 jack on
the master unit and the other end into the RJ45 jack on
the remote terminator.
3. Press the TEST button. One of the ID LED's will flash
three times. This indicates the number of the remote
identification unit attached to the far end of the subject
cable. The tester will then automatically continue with
the same cable test procedure as the standard LANtest
Pro.
Probe Features:
Special inductive plastic tip which prevents accidental
shorts (possible with copper-tip tracers) when using
near high voltage devices
Traces and identifies wires or cable in a bundle or group
without damaging cable insulation
Adjustable volume level for various work environments
Both amplifier and LED for loud or dark work
environments
Can work with any existing tone generator in the market
Probe Specifications:
Pen-style casing
Special inductive plastic tip
One push-button TRACE switch
One battery low LED indicator
One amplifier and one LED for signal detection
One rotary volume level switch
Probe Operation:
1. With the toggle switch on the side of the Probe unit,
select the mode of operation:
a. S & L: Speaker amplifier and LED tracing mode
b. Sp. : Speaker only tracing mode
c. L : LED only tracing mode
2. Press and hold the TRACE button while approaching
the subject cable. The intensity of the tone signal will
increase as the Probe approaches the cable.
Product Profile
2
14
12
3
LANtest
Remote Network Cable Tester
TM
Pro
16
15
9
13
LANtest
Remote Network Cable Tester
Pro
TM
REVERSED
SPLIT PAIRS
LOW BATTERY
TEST
MISWIRE
SHORT
11
10
1-2 3-6 4-5 7-8 SHIELD
6
8
7
4
5
1
4 5
256652/LB
1. Master port (RJ45)
2. Pair 1 indicator
3. Pair 2 indicator
4. Pair 3 indicator
5. Pair 4 indicator
6. Shield indicator
7. Short faults LED
8. Reversed faults LED
9. Miss wire faults LED
10. Split pairs LED
11. Battery low indicator
12. Test button
13. ON/OFF switch
14. Battery cover
15. Remote unit
16. Remote test port (RJ45)
256652/LBT (with tone generator model)
256652/IDT
LANtest Pro with tone generator and 4 remote IDs
2
14
17
12
3
LANtest
Remote Network Cable Tester
TM
Pro
16
15
9
13
LANtest
Remote Network Cable Tester
Pro
TM
REVERSED
SPLIT PAIRS
LOW BATTERY
TEST
4
MISWIRE
SHORT
2
3
1
11
10
1-2 3-6 4-5 7-8 SHIELD
TONE G.
ID
6
8
7
4
5
1
15
13
3
3
12
19
18
20
14
Remote
Terminator
Remote
Terminator
4
Pro
TM
LOW BATTERY
LANtest
Remote Network Cable Tester
17
2
Remote
Terminator
2
16
Remote
Terminator
1
7
1
2
3
ID
TONE G.
TEST
1-2 3-6 4-5 7-8 SHIELD
SHORT
REVERSED
MISWIRE
4
SPLIT PAIRS
11
8
10
9
1
4
5
6
256652/TK
256652/LBT with 256712A Probe
256652/TFK
256652/LBT with 256712F Probe (with Filter)
Remote Network Cable Tester
LANtest
TM
Pro
12
14
4
17
2
ID
4
3
2
1
TEST
LOW BATTERY
TONE G.
MISWIRE
REVERSED
SHORT
SPLIT PAIRS
3
Pro
TM
LANtest
Remote Network Cable Tester
16
1-2 3-6 4-5 7-8 SHIELD
9
11
10
13
8
6
5
7
15
1
CABLE
TRACER
6
4
3
8
7
5
1
2
2
3
MISWIRE
14
TRACER
CABLE
TM
4
Pro
12
17
LOW BATTERY
SPLIT PAIRS
3
Remote Network Cable Tester
LANtest
11
13
LANtest
Remote Network Cable Tester
6
ID
1-2 3-6 4-5 7-8 SHIELD
2
TONE G.
SHORT
16
REVERSED
TEST
9
8
7
10
1
15
Pro
TM
4
5
1
8
3
4
6
7
1
2
5
NOISE FILTER
INCLUDED
6 7
1. Master port (RJ45)
2. Pair 1 indicator
3. Pair 2 indicator
4. Pair 3 indicator
5. Pair 4 indicator
6. Shield indicator
7. Short faults LED
8. Reversed faults LED
9. Miss wire faults LED
10. Split pairs LED
11. Battery low indicator
12. Test button
13. ON/OFF switch
14. Battery cover
15. Remote unit
16. Remote test port (RJ45)
17. Tone indicator
1. Master port (RJ45)
2. Pair 1 indicator
3. Pair 2 indicator
4. Pair 3 indicator
5. Pair 4 indicator
6. Shield indicator
7. Short faults LED
8. Reversed faults LED
9. Miss wire faults LED
10. Split pairs LED
11. Battery low indicator
12. Test button
13. Cable/Tone generator/OFF switch
14. Battery cover
15. Remote unit #1
16. Remote unit #2
17. Remote unit #3
18. Remote unit #4
19. Remote test port (RJ45)
20. Tone indicator
1. Master port (RJ45)
2. Pair 1 indicator
3. Pair 2 indicator
4. Pair 3 indicator
5. Pair 4 indicator
6. Shield indicator
7. Short faults LED
8. Reversed faults LED
9. Miss wire faults LED
10. Split pairs LED
11. Battery low indicator
12. Test button
13. ON/OFF switch
14. Battery cover
15. Remote unit
16. Remote test port (RJ45)
1. Inductive Plastic Tip
2. Visible Signal indicator
3. Low Battery
4. Trace button
5. Volume
6. Light /Speaker & Light/off switch
7. Speaker
8. Battery Cover
1. Master port (RJ45)
2. Pair 1 indicator
3. Pair 2 indicator
4. Pair 3 indicator
5. Pair 4 indicator
6. Shield indicator
7. Short faults LED
8. Reversed faults LED
9. Miss wire faults LED
10. Split pairs LED
11. Battery low indicator
12. Test button
13. ON/OFF switch
14. Battery cover
15. Remote unit
16. Remote test port (RJ45)
1. Inductive Plastic Tip
2. Visible Signal indicator
3. Low Battery
4. Trace button
5. Volume
6. Light /Speaker & Light/off switch
7. Speaker
8. Battery Cover
Fault Status
Short
Open
Reversed
Miss-wire
Split
TEST
SHORT
SPLIT PAIRS
LOW BATTERY
MISWIRE
REVERSED
1-2 3-6 4-5 7-8 SHIELD
6
3
2
1
6
3
1
2
5
8
7
4
5
7
8
4
55
7
8
7
8
3
4
6
2
1
3
4
6
2
1
1-2 3-6 4-5 7-8 SHIELD
TEST
SPLIT PAIRS
LOW BATTERY
SHORT
REVERSED
MISWIRE
TEST
SHORT
LOW BATTERY
MISWIRE
SPLIT PAIRS
REVERSED
1-2 3-6 4-5 7-8 SHIELD
6
3
4
5
8
7
6
3
4
5
7
8
2
1
1
2
5
7
8
3
6
4
5
7
8
6
4
3
1
2
1
2
TEST
SPLIT PAIRS
LOW BATTERY
SHORT
REVERSED
MISWIRE
1-2 3-6 4-5 7-8 SHIELD
8
TEST
SPLIT PAIRS
LOW BATTERY
SHORT
REVERSED
MISWIRE
1-2 3-6 4-5 7-8 SHIELD
5
7
8
3
6
4
5
7
8
6
4
3
1
2
1
2
1-2 3-6 4-5 7-8 SHIELD
TEST
LOW BATTERY
SPLIT PAIRS
SHORT
REVERSED
MISWIRE
Low Battery
Battery Replacement
When the LOW BATTERY light illuminates, the battery does
not have sufficient power to support an accurate test. At this
time, you must replace it with a new battery.
Battery
Warning
1. Do not connect LANtest Pro to a live circuit as it may
damage the tester and interfere with a live network.
2. Testing in a high frequency activated area may cause the
tester to give inaccurate readings.
3. Do not drop or get the tester wet as it may cause internal
damage.
4. Do not place the tester in areas of high humidity or direct
sunlight.
5. Do not open the tester or attempt to repair in case of
malfunction. Please send it back to your distributor for
repair or replacement.
9
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

C2G 26846 Owner's manual

C2G
Brand
C2G
Model
26846
Category
Cable network testers
Type
Owner's manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents