Valor Auto Companion Inc. 1210DKA User manual

Brand
Valor Auto Companion Inc.
Model
1210DKA
Category
Fireplaces
Type
User manual

Valor Auto Companion Inc. 1210DKA is a door kit designed to be installed on the Valor model 1200 heater. The kit must be installed by a qualified installer, service agency, or gas supplier. It can be installed at the time the heater is installed or retrofitted afterward. The kit includes a backing plate, magnet bracket, and two doors. Installation of the door kit does not affect the heater's performance or safety. The doors can be installed with optional Cast Surrounds or Stone Trim Kits.

Valor Auto Companion Inc. 1210DKA is a door kit designed to be installed on the Valor model 1200 heater. The kit must be installed by a qualified installer, service agency, or gas supplier. It can be installed at the time the heater is installed or retrofitted afterward. The kit includes a backing plate, magnet bracket, and two doors. Installation of the door kit does not affect the heater's performance or safety. The doors can be installed with optional Cast Surrounds or Stone Trim Kits.

4001303-01
31-3/4”
35-3/4”
Overview
1200 Heater
Backing Plate
Wall Finish
Alhambra Doors
1210DKA Alhambra
Door Kit
(incl. magnet bracket)
Magnet
Bracket
© Copyright Miles Industries Ltd., 2007.
1210DKA Alhambra Door Kit
The 1210DKA Alhambra Door Kit may be tted to the Valor model 1200 heater, either at the time the heater is installed
or retrotted afterwards (provided existing wall and hearth nish allow—see Note above). Installation of the Alhambra
doors affect mantle clearances, framing dimensions, or other specications listed in the heater installation manual—see
installation manual packed with the heater. The 1210DKA Alhambra Doors may also be installed with optional
614CVI, 615CVI Cast Surrounds, 616STK, 617STK Stone Trim Kits (see installation instructions with each kit).
NOTE: The bottom of the plate is ush
with the bottom of the heater. Bottom
of the heater MUST be ush with or
higher than the nished hearth.
NOTE: To install the kit’s backing plate, the surface of the nished hearth or oor must be at
the same level as the bottom of the heater. Please be aware that the backing plate mounting
can ONLY accommodate 1/2” wall thickness.
Note: This kit must be installed or serviced by a qualied installer, service agency or gas supplier.
These instructions are to be used in conjunction with the main installation instructions for the 1200.
CSA approved for use with Valor Model 1200 Heater ONLY
INSTALLATION INSTRUCTIONS
Mantel or Shelf Clearances
For Mantel of Shelf Clearances, see the Installation manual provided with the 1200DV Ventana engine.
2
© Copyright Miles Industries Ltd., 2007.
3/8”
3/4”
Installation
Install heater as per installation instructions.
Finish wall up to the outside edge of the rebox
front opening. Allow for height of nished hearth
or backing plate will not install. Make sure that
the wall nish is no thicker than 1/2”.
Remove the 6 screws retaining the top and
side black strips surrounding the opening of the
rebox, as shown.
Install the backing plate with the four screws
provided, xing it at the top and on each side,
as shown.
In the middle of the replace’s black sheet metal
front plinth, drill through the two dimples with an
1/8” bit.
Fix the magnet bracket to the black sheet metal
front plinth with the two screws provided.
1.
2.
3.
4.
5.
Insert one hinge pin, long side up, in one of the bottom
hinge brackets on the backing plate.
Drop the bottom of one door onto the hinge pin.
Align the top of the door under the upper hinge bracket.
Drop the top hinge pin through the bracket, in the door
frame. Repeat with the other door.
6.
7.
8.
Page is loading ...
Page is loading ...
Page is loading ...
6
© Droits d’auteur Miles Industries Ltd., 2007.
1 4001300 Plaque de soutien
2 4001083CP Porte gauche
3 4001084CP Porte droite
4 4001418 Quincaillerie
Liste de pièces
Conçues et fabriquées par / pour
Miles Industries Ltd.
190–2255 Dollarton Highway, North Vancouver, C.-B., CANADA. V7H 3B1
Tél. : 604-984-3496 Téléc. : 604-984-0246
www.milesreplaces.com
1
2
3
4
4
4
4
4
}
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Valor Auto Companion Inc. 1210DKA User manual

Brand
Valor Auto Companion Inc.
Model
1210DKA
Category
Fireplaces
Type
User manual

Valor Auto Companion Inc. 1210DKA is a door kit designed to be installed on the Valor model 1200 heater. The kit must be installed by a qualified installer, service agency, or gas supplier. It can be installed at the time the heater is installed or retrofitted afterward. The kit includes a backing plate, magnet bracket, and two doors. Installation of the door kit does not affect the heater's performance or safety. The doors can be installed with optional Cast Surrounds or Stone Trim Kits.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Other documents