Swisher ZT2766KP Owner's manual

Brand: Swisher

Model: ZT2766KP

Category: Lawnmowers

Type: Owner's manual

OWNER’S MANUAL

1602 CORPORATE DRIVE, WARRENSBURG, MISSOURI 64093

PHONE 660-747-8183 FAX 660-747-8650

Manufacturing quality lawn care equipment since 1945

Made In The

USA

14690 Rev. 11-087

STARTING SERIAL # L111-087001

CELEBRATING 65 YEARS OF INNOVATION

SINCE 1945

27 HP – 66” CUT

ZT2766KP & ZT2766KP-CA

LIMITED WARRANTY

The manufacturer’s warranty to the original consumer purchaser is:

This product is free from defects in materials and workmanship for a period of two (2) years

from the date of purchase by the original consumer purchaser.

As required by CFR § 1060.120, the fuel system related components, which have been

certified to this equipment by SAI are to be free of defects in material and workmanship for a

period of two (2) years from the date of purchase by the original consumer purchaser.

We will repair or replace, at our discretion, parts found to be defective due to materials or

workmanship. This warranty is subject to the following limitations and exclusions:

In the event you have a claim under this warranty, you must return the product to an authorized

service dealer. All transportation charges, damage, or loss incurred during transportation of parts

submitted for replacement or repair under this warranty shall be borne by the purchaser. Should

you have any questions concerning this warranty, please contact us toll-free at 1-800-222-8183.

The model number, serial number, date of purchase, and the name of the authorized Swisher

dealer from whom you purchased the mower will be needed before any warranty claim can be

processed.

THIS WARRANTY DOES NOT APPLY TO ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

AND ANY IMPLIED WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED

HEREIN FOR ALL EXPRESSED WARRANTIES. Some states do not allow the limitation of

consequential damages or limitations on how long an implied warranty may last, so the above

limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you

may have other rights, which vary from state-to-state. This is a limited warranty as defined by the

Magnuson-Moss Act of 1975.

1) Engine Warranty All engines utilized on our products have a separate warranty

extended to them by the individual engine manufacturer. Any

engine service difficulty is the responsibility of the engine

manufacturer and in no way is Swisher or its agents responsible

for the engine warranty. The Briggs & Stratton Engine Service

Hot-Line is 1-800-233-3723. The Tecumseh Engine Service Hot-Line

is 1-800-558-5402.

2) Commercial Use This product is not intended for commercial use and

carries no commercial warranty.

3) Limitation This warranty applies only to products which have been

properly assembled, adjusted, and operated in accordance

with the instructions contained within this manual. This

warranty does not apply to any product of Swisher that

has been subject to alteration, misuse, abuse, improper

assembly or installation, shipping damage, or to normal

wear of the product.

4) Exclusions Excluded from this warranty are normal wear, normal

adjustments, normal maintenance, and battery*(see

battery section.)

CONTENTS

LIMITED WARRANTY…………

OPERATION………………..……….

INTRODUCTION………………

Features……………………………………

13-14

General……………………………………..

Starting………………………………………

Before Operating……………………

Grass Height of Cut………………

Uncrating & Assembly……………

Controls………...……..………………….

SYMBOLS & DECALS……….

SERVICE & ADJUSTMENTS..

SAFETY INSTRUCTIONS…….

Adjusting Deck Height…………..

General use and safety rules…

Deck Level……………………………….

Children Safety……………. 8

Parking Brakes………………. 18

Slope Operation…………….. 8

Deck Belt Replacement……… 19

CUSTOMER

Hydro Belt Replacement…….. 21

RESPONSIBILITY……………

Seat Adjustment……………… 21

Operator Presence……………….

WIRING SCHEMATIC…………..

21-22

Tires……………………………………………

PARTS BREAKDOWN…………..

23-33

Blade Maintenance…………………..

TROUBLESHOOTING……………

34-35

Battery………………………………………

MOWER IDENTIFICATION……..

V-belts……………………………………..

REPLACEMENT PARTS………..

Engine………………………………………..

WARRANTY RIGHTS……………..

Overall Unit Care………….………..

Transporting Safety……………….

SPECIFICATIONS……………..

Maintenance……….…………………..

INTRODUCTION

Congratulations

Thank you for purchasing a Swisher Zero Turn mower. This machine is built for the

reatest efficiency and rapid mowing of large areas. Conveniently located controls and

dual commercial grade hydrostatic transmissions regulated by steering levers, contribute to

the machine’s performance.

This manual is a valuable document. Following the instructions for use, service,

maintenance, etc. can greatly increase the life-span of your machine .

General

In this operator’s manual, left and right, backward and forward are used in relation to the

normal operators position.

Read Before Operating

This machine is constructed only for mowing grass on lawns and other free and even

round without obstacles. This machine is not intended for commercial use. The

manufacturer’s directions concerning operation, maintenance, and repairs must be

carefully followed.

This machine must only be operated, maintained, and repaired by persons that are

familiar with the machine’s special characteristics and who are well versed in safety

instructions.

Accident prevention regulations, other general safety regulations, occupational safety

rules, and traffic regulations must be followed without fail.

Unauthorized modifications to the design of the machine may absolve the manufacturer

from liability for any resulting personal injury or property damage.

 Read engine manufacturer’s

operating and maintenance instructions.

 Read and observe all safety

instructions on your mower and in the

manual.

 Check engine oil.

 Check fuel caps to sure that they

are in place.

 Know how to set the parking brake.

 Be sure mower blades are turned off –

PTO switch pushed down.

 Know how to stop the engine – Turn key

to off

 Know how to stop the unit – Return

control handles to neutral

NOTE:

If you have never used a Zero Turn mower before, refer

the Operation Controls section of this manual before

attempting to operate one for the first time.

INTRODUCTION

Uncrating & Assembly

 D

ispose of top and side panels of the crate.

 Remove loose parts and packing material.

 Cut any banding or strapping that may be holding the mower to the crate.

 Disengage spark plug wire and place where it cannot make a connection.

 Raise the mower deck to its highest position.

 Install steering levers. Remove the bolts from the control arms on the mower. Align

the holes in the lever with the holes in the control arms and attach with the bolts provided.

Make sure both bolts on both handles are tight.

 Disengage the parking brake by pushing the handles to their fully extended position.

 Open the transmission valves at the rear of the unit by pulli

ng the release rods and

locking them in place. SEE INSTRUCTION DECAL AT THE REAR OF THE UNIT.

 Carefully push the mower off the crate to a safe and level area.

 Check engine oil. All engines are filled with oil and tested at the factory. Verify oil

level and add if necessary before starting engine. SEE ENGINE OWNER’S MANUAL

 Check the battery. If the battery is put into service after the “month & year” of the

date on the battery, then it may need to be charged with a 12 volt charger for a minimum

of 1 hour, but no more than 2 hours at a rate of 6 to 10 amps.

 Attach battery cables to battery. Always attach the positive terminal first.

 Close the transmission valves at the rear of the unit. SEE INSTRUCTION DECAL

AT THE REAR OF THE UNIT.

 Reconnect spark plug wire.

 Check tire pressure on all four wheels. REFER TO UNIT SPECIFICATIONS TABLE

TOOLS REQUIRED:

 2

- ½” Wrenches or ½” Socket with drive ratchet

 Tire pressure gauge

 Nail bar or claw hammer

 Wire snips

To Remove The Mower From The Crate:

SYMBOLS & DECALS

Triangle Danger Decal – OD55

Swisher Flag U.S.A.– OD39

Notice Do Not Alter Wiring Decal– OD74

Operator Must Be Seated Decal– OD73

Flying Debris Decal – OD43

No Step Decal – OD11

OD45- Warning Decal

Key/PTO Decal - 10273

Hydro Release -

10280

Throttle/Choke Decal - 10271

Danger/Warning Decal - 10276

SAFETY INSTRUCTIONS

These instructions are for your safety. Read them carefully.

General Use

 Read all instructions in this operator’s manual and on the

machine before starting it. Ensure that you understand them and

then abide by them.

Learn how to use the machine and its controls safely and learn

how to stop quickly. Also learn to recognize the safety decals.

 Only allow the machine to be used by adults who are familiar

with its use.

 Make sure nobody else is in the area of the machine when you

start the engine, engage the drive, or run the machine.

Stop the machine if someone enters the work area.

Clear the area of objects such as stones, toys, steel wire, etc.

that may become caught in the blades and thrown out.

D

o Not Use this machine without the Discharge

Chute in place.

This Safety Alert Symbol indicates important messages in this manual. When

you see this symbol, carefully read the message that follows and be alert to the

possibility of personal injury.

NOTE:

If you have never used a Zero Turn

mower before, refer to the Operation

Controls section of this manual before

attempting to operate one for the first

time.

 Stop the engine and disconnect the spark plug before cleaning

the discharge deck.

 Never take passengers. The machine is only intended for use

by one person.

 Always look around before and during reversing maneuvers.

 Slow down before turning.

 Shut down the mower deck when not mowing.

 Be careful when rounding fixed objects, so that the blades do

not hit them.

 Only operate the machine in daylight or other well-lit

conditions.

 Keep the machine a safe distance from holes or other

irregularities in the ground.

 Never use the machine if you are tired, if you have consumed

alcohol, or if you are taking other drugs or medications that can

affect your vision, judgment, or coordination.

 Beware of traffic when working near or crossing a road.

 Never leave the machine unsupervised with the engine running.

Always shut down the blades, engage the parking brake, stop the

engine, and remove the ignition key before leaving the machine.

 Never allow children or other persons not trained in the use of

the machine to use or service it. Local laws may regulate the age

of the user.

 Make sure that you have first aid equipment close at hand

when using the machine.

 Never use the machine when barefoot. Always wear protective

shoes or boots.

 Always wear approved protective glasses or a full visor when

assembling or driving.

 Ear Protection is recommended

 Never wear loose clothing that can get caught in moving parts.

SAFETY INSTRUCTIONS

General Use Continued…

Remember

The operator is responsible for

avoiding dangers or accidents.

WARNING

When using the machine,

approved personal

protective equipment shall

be used. Personal

protective equipment

cannot eliminate the risk of

injury, but it will reduce the

degree of injury if an

accident does occur. Ask

your retailer for help in

choosing the right

equipment.

Slope Operation

 Remove obstacles such as stones, tree branches, etc.

 Mow up and down, not side to side. Never drive the rider on terrain that slopes

more than 10 degrees.

 Avoid starting or stopping on a slope. If the tires begin to slip, shut down the

blades and drive slowly down the slope.

 Always drive evenly and slowly on slopes.

 Make no sudden changes in speed or direction.

 Avoid unnecessary turns on slopes, and if it proves necessary, turn slowly and

gradually downward, if possible.

 Watch for holes, ruts, or bumps. On uneven terrain, the machine can tip more

easily. Long grass can hide obstacles.

 Drive slowly and use small movements of the steering controls.

 Do not mow wet grass. It is slippery, and the tires can loose their grip, so that

the machine slides.

 Do not try to stabilize the machine by putting a foot on the ground.

Remember

The operator is responsible

for avoiding dangers or

accidents.

 Serious accidents may occur if you fail to be on guard for children in

the area of the machine. Children are often attracted to the machine and

mowing work. Never assume that children will stay put where you last saw

them.

 Keep children away from the mowing area and under close supervision

by another adult.

 Shut off the machine if children enter the work area.

 Never allow a child to ride with you.

 Never allow children to operate the machine.

 Be extra cautious near corners, bushes, trees, or other objects that

block your view.

Children

MOWING SAFETY

•WARNING – Petrol is highly flammable.

- store fuel in containers specifically designed for this purpose;

- refuel outdoors only and do not smoke while refueling;

- add fuel before starting the engine. Never remove the cap of the fuel tank or add petrol while the engine

is running or when the engine is hot.

- if petrol is spilled, do not attempt to start the engine but move the machine away from the area of spillage and

avoid creating any source of ignition until petrol vapors have dissipated;

- replace all fuel tanks and container caps securely.

• Replace faulty silencers;

• before using, always visually inspect to see that the blades, blade bolts and cutter assembly are not worn

or damaged. Replace worn or damaged blades and bolts in sets to preserve balance;

• on multi-bladed machines, take care as rotating one blade can cause other blades to rotate.

MAINTENANCE AND STORAGE

• Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition;

• never store the equipment with petrol in the tank inside a building where fumes can reach an open flame or

spark;

• allow the engine to cool before storing in any enclosure;

• to reduce the fire hazard, keep the engine, silencer, battery compartment and petrol storage area free of grass,

leaves, or excessive grease;

• check the grass catcher frequently for wear or deterioration;

• replace worn or damaged parts for safety;

• if the fuel tank has to be drained, this should be done outdoors.

• when machine is to be parked, stored or left unattended, lower the cutting means unless a positive mechanical

lock is used.

TRAINING

All drivers should seek and obtain professional and practical instruction. Such instruction should emphasize:

• the need for care and concentration when working with ride-on machines;

• control of a ride-on machine sliding on a slope will not be regained by the application of the brake. The main

reason for loss of control are:

i) insufficient wheel grip;

ii) being driven too fast;

iii) inadequate braking;

iv) the type of machine is unsuitable for its task;

v) lack of awareness of the effect of ground conditions, especially slopes;

vi) incorrect hitching and load distribution.

OPERATION

• Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect;

• when using any attachments, never direct discharge of material toward bystanders nor allow anyone

near the machine while in operation;

• never operate the machine with defective guards, or without safety protective devices in place;

• do not change the engine governor settings or over speed the engine. Operating the engine at excessive

speed can increase the hazard of personal injury;

• disengage drive to attachments, stop the engine, and disconnect the spark plug wire(s) or remove the

ignition key:

- before clearing blockages or unclogging chute;

- before checking, clearing or working on the machine;

- after striking a foreign object. Inspect the machine for damage and make repairs before restarting and

operating the equipment;

- if the machine starts to vibrate abnormally (check immediately);

• stop the engine and disengage drive to attachment:

- before refueling;

- before removing the grass catcher;

- before making height adjustment unless adjustment can be made from the operator’s position

•To avoid a battery explosion, never attempt to charge a frozen battery.

•Warning: Gel and AGM (Absorbed Glass Mat) batteries require a voltage-limited charger. Charging a

Gel or AGM battery on a typical shop charger, even one time, may greatly shorten its life.

•Important: Never overcharge batteries. Excessive charging will shorten battery life.

•Prior to charging, read the manufacturer’s instructions for proper charger hook-up and use.

•Turn off charger prior to hook-up to avoid dangerous sparks. PROTECT YOUR EYES!

•Warning: If the electrolyte is accessible, verify that plates are covered before beginning to charge. At the

end of charge, add distilled water as needed to bring levels to the proper height. If water is added, charge

for an additional 30 minutes to mix. If electrolyte levels are low but battery is not accessible, remove

battery from service.

CUSTOMER RESPONSIBILITIES

Operator Presence System

Be sure the operator presence and interlock systems are working properly. If your mower does not function as

described, repair the problem immediately.

 The engine should not start unless the parking brake is engaged and the PTO (Blade Engagement – See

OPERATION FEATURES section of this manual) switch is disengaged (pressed down).

 When the engine is running, the operator should never leave the seat without first setting the parking brake

and shutting off the engine.

 When the engine is running and the PTO switch is engaged, any attempt by the operator to leave the seat

without first disengaging the PTO switch, should shut off the engine.

 When the engine is running and the control levers are rotated in, the operator should never attempt to leave

the seat without rotating the control levers out, shutting off the engine and engaging the parking brake.

The PTO switch should never engage without the operator on the seat.

Tires

 Maintain proper air pressure in all tires ( SEE SPECIFICATIONS section)

 Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

 Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

Blade Maintenance

CAUTION

Stop engine and remove ignition key for safety. Disconnect spark plug wire. Wear heavy, thick gloves when

holding onto blade. Avoid the sharp edge of the blade.

For best results, mower blades must be kept sharp. Replace bent or damage blades.

 Safely raise front of mower. SEE WARNING

 Hold or block blade from turning.

 Loosen blade nut and remove blade.

 Replace blade, (SEE SPECIFICATIONS).

WARNING

When it is necessary to raise the mower for

any repair or service, use jackstands to

provide adequate support. DO NOT rely on

hydraulic or mechanical jacks

Battery

The battery contains sulfuric acid and

electrolytes which are poisonous and

corrosive.

To clean battery and terminals

 R

emove terminal guard.

Disconnect the BLACK battery cable first, then the RED battery cable and remove the battery.

 Rinse the battery with plain water and dry.

 Clean terminals and battery cable ends with wire brush until shiny.

 Coat terminals with grease or petroleum jelly

 Reinstall battery

 Reconnect the battery cables

WARNING

CHARGING TIPS

CUSTOMER RESPONSIBILITIES/SPECIFICATIONS

V-Belts

Check V-belts for deterioration and wear after 100 hours of

operation and replace if necessary. Replace belts if they

begin to slip from wear. SEE SPECIFICATION for belt part

numbers and SERVICE section of this manual for

instructions on how to replace the belt.

Engine

REFER TO YOUR ENGINE OWNERS MANUAL

Overall Unit Care

 Reduce the risk of fire by removing grass, leaves,

and other debris that may have accumulated on the

machine. Allow the machine time to cool before cleaning

or putting it in storage.

Wash mower periodically. Clean above and below

deck.

Keep all electrical connections clean and tight.

Driving and Transport

on Public Roads

Check applicable road traffic regulations before driving

and transporting on public roads.

If the machine is transported, you should always use

approved fastening equipment and ensure that the

machine is well anchored.

The cutting deck should also be lowered to the lowest

position and the parking brake engaged.

FRONT: 13 x 6.5 x 6

EAR: 23 x 10.5 x 12

TIRE SIZE

27 + - 3 ft. lbsHYDRO Bolt Torque

Pivoting FRONT AXLE

Electric ActuatorDECK LIFT

15” Back w/ Arm Rest

6” Adjustable Slide

Air Ride Suspension With Lumbar

Support.

SEAT

Commercial Grade Eaton Hydrostatic TRANSMISSION

Spring AssistedPARKING BRAKE

1.5” – 5”CUTTING HEIGHT

66” – 3 Mulching Blade SystemCUTTING WIDTH

LENGTH: 70”

WIDTH: 66 1/4 “

Including Deck

WEIGHT: 950 lbs

UNIT MEASUREMENTS

35 ft. lbsBLADE BOLT TORQUE

12V / Heavy Duty 275 CCA

Type U1L

BATTERY

FRONT: 28 psi Max

REAR: 20 psi Max

TIRE PRESSURE

0 – 8 mphGROUND SPEED

SEE ENGINE MANUALSPARK PLUG

SEE ENGINE MANUALOIL TYPE (SPI-SF-SJ):

DUAL 5.0 GAL TANKS

UNLEADED REGULAR

GASOLINE CAPACITY

AND TYPE

SPECIFICATIONS

6 V 12 V 50 AMPS 30 AMPS 20 AMPS 10 AMPS

6.3 12.6 100%

6.2 12.4 75% 20 MIN. 35 MIN. 48 MIN. 90 MIN.

6.1 12.2 50% 45 MIN. 75 MIN. 95 MIN. 180 MIN.

6 12 25% 65 MIN. 115 MIN. 145 MIN. 280 MIN.

5.9 11.8 0% 85 MIN, 150 MIN. 195 MIN. 370 MIN.

FULL CHARGE

VOLTAGE

STANDARD

BATTERY

STATE

CHARGE

APPROX. BATTERY CHARGING TIME *

TO FULL CHARGE AT 80

F/27

MAXIMUM RATE AT

* Test wet batteries every 4-6 months and recharge if necessary.

Always test and charge if necessary before installation.

•The maximum charge rate in amperes should be no more than 1/3 of the battery’s reserve capacity

minute rating. If the terminal voltage exceeds 16.0 volts while charging, reduce the charge rate.

•Continue charging and reduce the rate as needed until a 2 hour period results in no increase in voltage or

decrease in current.

If violent gassing or spewing of electrolyte occurs, or the battery case feels hot to the touch, temporarily

reduce or halt charging.

CUSTOMER RESPONSIBILITIES

MAINTENANCE SCHEDULE

1,2

Replace Oil Filter

Check Operator

Presence

Replace Spark Plug

Clean Engine

Cooling Fins

Inspect Muffler

Clean Air Filter

Replace Fuel Filter

1,2

Change Engine Oil

w/o filter

1,2

Change Engine Oil

w/ filter

Check Engine Oil

Check Belts

Clean Battery &

Terminals

Check Battery

Sharpen/Replace

Mower Blades

XXX

Check for Loose

Fasteners

Parking Brake

Before

Each

Use

Before

Storage

8 Hours 25 Hours 50 Hours 100 Hours Season

Check Brake

Operation

Check Tire

Pressure

1 – Change more often when operating under a heavy load or in high ambient temperatures

2 – Service more often when operating in dirty or dusty conditions

3 – Replace blades more often when mowing in sandy soil

OPERATION

FEATURES

1. Throttle Control – Used to control

Engine Speed

2. Hour Meter – Indicates hours of

operation

3. Choke Control – Used when starting

a cold engine

4. PTO Switch – Used to engage or

disengage the deck blades

5. Ignition Switch – Used to start or

stop the engine

7. Control Lever – Sets the speed of the

mower in both the forward and reverse

directions and also turns the mower.

8. Hydro Bypass – Engages transmissions for

normal operation and disengages

transmissions for pushing or pulling the unit

9. Fuel Tanks – Dual 5.0 gal fuel tanks

10. Seat Slide

11. Battery

12. Pivoting Front Axle

13. Discharge Chute

OPERATION

FEATURES

1. Throttle Control – Used to control

Engine Speed

2. Hour Meter – Indicates hours of

operation

3. Choke Control – Used when starting

a cold engine

4. PTO Switch – Used to engage or

disengage the deck blades

5. Ignition Switch – Used to start or

stop the engine

7. Control Levers – Sets the speed of the

mower in both the forward and reverse

directions and also turns the mower.

8. Hydro Bypass – Engages transmissions for

normal operation and disengages

transmissions for pushing or pulling the unit

9. Fuel Tanks – Dual 5.0 gal fuel tanks

10. Seat Slide

11. Battery

12. Pivoting Front Axle

13. Discharge Chute

Left Control Panel Right Control Panel

Rear of Unit

1 2

OPERATION

Starting

 O

perator must be sitting in the seat. Control handles must be in the neutral

(outward) position. PTO must be in the disengage position (pushed down).

 Set choke (if needed), turn key and release as soon as engine starts. Adjust

throttle to half and shut choke off.

 Be sure all people are clear of the area. Set Engine RPM to maximum and then

engage blades.

Grass Height & Cutting Suggestions

 D

o not attempt to cut wet grass

 The average lawn should be cut to 2 ½” during the cool season and to over 3”

during the hot months. For healthier and better looking lawns, mow often and after

moderate growth.

 As a rule , never cut more than 1/3 of the total grass blade length. Correct

mowing height can reduce weeds and lawn disease.

 For best performance, grass over 6 inches in height should be mowed twice.

The first cut should be set relatively high and the second set to the desired height.

NOTE:

If you have never used a Zero

Turn mower before, refer to the

Operation Controls section of

this manual before attempting

to operate one for the first time.

Controls

 B

e familiar with all controls, their functions and how to operate them before

starting the machine.

Motion control levers on each side of the console control the direction of

movement. SEE FIGURE BELOW

Note: The pressure required to operate the mower is very slight

Control Handles

Neutral Position Slow Forward Fast Forward

OPERATION

90 Degree Right Turn 90 Degree Left Turn Slow Reverse

360 Degree Right Turn 360 Degree Left Turn

NOTE:

If you have never used a Zero

Turn mower before, refer to the

Operation Controls section of

this manual before attempting

to operate one for the first time.

SERVICE & ADJUSTMENTS

 Use the actuator switch to raise or lower the deck to the desired position.

 Position 1 is the lowest setting and Position 8 is the highest position

 The cutting range is from approximately 1 ½” to approximately 5”

Adjusting The Cutting Height

TOOLS REQUIRED:

 2

- ½” Wrenches or ½” Socket with drive ratchet

 Lower the cutting deck down to the lowest position (position 1)

 Loosen the nuts on the top side of the deck hanger brackets (3 places) where the lift chains attach to.

 With all three loose on top of the brackets the deck should now set on the ground resting on the roller

wheels.

 Tighten the nuts on the top of the lift brackets making sure that all three lift chains are pulled tight.

 Lift deck using the deck lift handle to the desired position

Deck Leveling

Parking Brakes

The Swisher ZT2766KP is equipped with An Automatic Parking Brake system on each control handle.

When the control handles are in the out most position the parking brakes are on.

Adjustment for the system is located on the ends of the brake cable at the hydro pan & frame.

Raise the rear wheel off the ground

Disengage the hydro to be adjusted with the hydro release handle at the rear of the unit.

Adjust so that the brake is not on when the handles are in the operator position. The wheel should turn freely.

The wheel should not turn when the handle is moved to the engaged or outward position.

To tighten the brake, turn the adjustment nuts towards the end of the cable

Recheck adjustment with control handle

Lower unit back to the ground

Reengage the hydro at the rear of the unit

WARNING

When it is necessary to raise the mower for any

repair or service, use jackstands to provide

adequate support. DO NOT rely on hydraulic or

mechanical jacks

SERVICE & ADJUSTMENTS

Deck Belt Routing &

eplacement

 Disconnect spark plug wire

Apply parking brake

 Lower the deck to its lowest position

 Remove the belt covers

 Disconnect tension idler

 Roll the belt over the top of the deck pulleys

 Remove belt

Removal

 Install new belt by placing it around

the deck pulleys. Refer to routing

diagram below.

 The belt will be loose at this time

 Tightly secure the belt tension back

to its original position

 Reinstall the belt covers

 Reconnect spark plug wire

Replacement

Front of Unit

For replacement belt part number refer to Replacement Parts

uick Reference Chart in this manual

12527 - Belt

Hydro Belt Routing & Replacement

 D

isconnect spark plug wire

 Apply parking brake

 Disconnect wiring from electric clutch

 Remove clutch stop weldment (9973TK)

 Remove the engine to deck belt

 Disconnect idler spring

 Disconnect tension idler

 Remove belt from the engine pulley and from

the Hydro pulleys

Removal

 Install new belt by placing it around

the engine pulley and the hydro

pulleys. Refer to routing diagram

below.

 The belt will be loose at this time

 Tightly secure the belt tension back

to its original position

 Reinstall the belt from the engine to

the deck

 Reconnect wiring to the electric

clutch

 Reconnect spark plug wire

Replacement

SERVICE & ADJUSTMENTS

Engine Pulley

Idler Pulley

For replacement belt part number refer to Replacement Parts

Quick Reference Chart in this manual

037X66 - Belt

SERVICE & ADJUSTMENTS

Seat Adjustment

ngine to Deck Belt

 A

pply parking brake

 Lower the deck to its lowest position

 Disconnect tension idler

 Remove belt from the mower deck and the

electric clutch

Removal

 Install new belt by placing it around

the electric clutch and route it through

the idler and around the deck pulley.

Refer to routing diagram below.

 The belt will be loose at this time

 Tightly secure the belt tension back

to its original position

Replacement

 To improve the tracking of the Swisher ZT2766KP the speed of one of the rear wheels

needs to be decreased. If the ZT2766KP pulls to the right the left wheel will need to decrease

speed and if pulling to the left the right wheel will need to decrease speed.

 To decrease the speed in one of the rear wheels turn the bolt counter clockwise. This will

limit travel of the handle. Ensure after the bolt has been moved that the nuts holding the bolt

in place are securely tightened.

 The Swisher ZT2766KP is equipped with a 6” range sliding seat.

 Release the tension on the seat adjustment lever by pushing the yellow tip lever

to the left. See features section in this manual

 Using your own weight, slide the seat to the desired position

 Release the lever

 Adjust knob on front of seat to desired position, for air suspension adjust

lumbar support as desired.

Travel Reduction Adjustment

14454 - Belt

Page is loading ...

Swisher ZT2766KP Owner's manual

Brand: Swisher

Model: ZT2766KP

Category: Lawnmowers

Type: Owner's manual

Download PDF

report

Swisher ZT2766KP Owner's manual

Swisher ZT2766KP Owner's manual

Related papers

Other documents