Miller KC000000 Owner's manual

Type
Owner's manual

This manual is also suitable for

OWNER’S MANUAL
December 1992 FORM: OM-683
Use above FORM number when ordering extra manuals.
For No. 17A Running Gear/Cylinder Rack 042 694
WARNING
ELECTRIC SHOCK can kill.
Do not touch live electrical parts.
Turn OFF welding power source and disconnect
input power before installing onto running gear.
Disconnect input power conductors from
deenergized supply line BEFORE moving welding
power source.
CYLINDERS can explode if damaged.
Keep cylinders away from welding and other
electrical circuits.
Never touch cylinder with welding electrode.
Always secure cylinder to running gear, wall, or
other stationary support.
FALLING EQUIPMENT can cause injury
and damage.
Lift unit only with proper equipment and correct
procedures.
If using lift forks, be sure forks extend out of opposite
side of unit.
Do not place any part of the body under the unit while
it is suspended.
miscwarn1.1* 9/91
1 Chassis Frame
2 Axle Shaft
Insert axle shaft through chassis
frame and install rear wheels with
washers and retaining rings.
3 Steering Gear Yoke
Install handle and front wheel onto
steering gear yoke with 3/4-10 x 5 in
screw and nut.
Coat washers and shaft portion of
yoke with grease, and install yoke
assembly to chassis frame with
washers and retaining ring.
4 Foot Control Pan
Install pan with 1/4-20 x 3/4 in self-
tapping screws.
5 Cylinder Rack
6 Cable Hanger
Install cylinder rack and cable
hangers with 1/4-20 x 3/4 in screws
and nuts.
Install chains; crimp S-hooks.
7 Bracket
Attach welding power source to
running gear with supplied brackets
and 1/4-20 x 3/4 in self-tapping
screws.
ST-157 435 / ST-157 509-A
1
2
3
5
6
4
7
3/8 in, 1-1/8 in
Tools Needed:
Figure 1. Running Gear/Cylinder Rack
OM-683 Page 2
ST-157 435
1
2
3
4
7
6
5
8
9
10
11
12
13
1415
16
14
Includes
Item 18
15
19
20
21
22
17
18
Figure 2. Complete Assembly
Description
Part
No.
Item
No.
Figure 2. Complete Assembly
Quantity
1 150 555 PAN, control foot 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 604 224 SCREW, slf forming stl hexwhd .250-20 x .750 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 009 970 BRACKET, mtg unit 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 022 617 CHAIN, cyl racks (consisting of) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 602 384 SNAP, chain 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 602 387 CHAIN, weldless 2/0 x 27.000 lg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 602 389 HOOK, S blunt 1.500 in 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 150 563 CYLINDER RACK 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 150 535 HANGER, cable 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 108 940 SCREW, cap stl hexhd .250-20 x .750 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 089 800 NUT, stl flg lkd hex .250-20 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 003 659 AXLE, running gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 121 614 RING, retaining ext .750 shaft x .085grv depth 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 602 250 WASHER, flat stl SAE .750 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 044 922 WHEEL, rubolene 8 in dia x 2 wide x .750 axle 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 150 562 FRAME, chassis 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 098 329 YOKE, steering gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 121 614 RING, retaining ext .750 shaft x .085grv depth 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 098 331 SCREW, cap stl hexhd .750-10 x 5.000 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 098 332 NUT, stl slflkg hex reg .750-10 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 098 330 HANDLE, steering gear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22 604 423 GRIP, handle .875 ID x 4.500 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
  • Page 1 1
  • Page 2 2

Miller KC000000 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI