OWNER’S MANUAL
December 1992 FORM: OM-683
Use above FORM number when ordering extra manuals.
For No. 17A Running Gear/Cylinder Rack 042 694
WARNING
ELECTRIC SHOCK can kill.
• Do not touch live electrical parts.
• Turn OFF welding power source and disconnect
input power before installing onto running gear.
• Disconnect input power conductors from
deenergized supply line BEFORE moving welding
power source.
CYLINDERS can explode if damaged.
• Keep cylinders away from welding and other
electrical circuits.
• Never touch cylinder with welding electrode.
• Always secure cylinder to running gear, wall, or
other stationary support.
FALLING EQUIPMENT can cause injury
and damage.
• Lift unit only with proper equipment and correct
procedures.
• If using lift forks, be sure forks extend out of opposite
side of unit.
• Do not place any part of the body under the unit while
it is suspended.
miscwarn1.1* 9/91
1 Chassis Frame
2 Axle Shaft
Insert axle shaft through chassis
frame and install rear wheels with
washers and retaining rings.
3 Steering Gear Yoke
Install handle and front wheel onto
steering gear yoke with 3/4-10 x 5 in
screw and nut.
Coat washers and shaft portion of
yoke with grease, and install yoke
assembly to chassis frame with
washers and retaining ring.
4 Foot Control Pan
Install pan with 1/4-20 x 3/4 in self-
tapping screws.
5 Cylinder Rack
6 Cable Hanger
Install cylinder rack and cable
hangers with 1/4-20 x 3/4 in screws
and nuts.
Install chains; crimp S-hooks.
7 Bracket
Attach welding power source to
running gear with supplied brackets
and 1/4-20 x 3/4 in self-tapping
screws.
ST-157 435 / ST-157 509-A
1
2
3
5
6
4
7
3/8 in, 1-1/8 in
Tools Needed:
Figure 1. Running Gear/Cylinder Rack
OM-683 Page 2
ST-157 435
1
2
3
4
7
6
5
8
9
10
11
12
13
1415
16
14
Includes
Item 18
15
19
20
21
22
17
18
Figure 2. Complete Assembly
Description
Part
No.
Item
No.
Figure 2. Complete Assembly
Quantity
1 150 555 PAN, control foot 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 604 224 SCREW, slf forming stl hexwhd .250-20 x .750 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 009 970 BRACKET, mtg unit 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 022 617 CHAIN, cyl racks (consisting of) 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 602 384 SNAP, chain 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 602 387 CHAIN, weldless 2/0 x 27.000 lg 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 602 389 HOOK, S blunt 1.500 in 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 150 563 CYLINDER RACK 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 150 535 HANGER, cable 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 108 940 SCREW, cap stl hexhd .250-20 x .750 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
11 089 800 NUT, stl flg lkd hex .250-20 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12 003 659 AXLE, running gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13 121 614 RING, retaining ext .750 shaft x .085grv depth 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14 602 250 WASHER, flat stl SAE .750 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 044 922 WHEEL, rubolene 8 in dia x 2 wide x .750 axle 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 150 562 FRAME, chassis 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17 098 329 YOKE, steering gear (consisting of) 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 121 614 RING, retaining ext .750 shaft x .085grv depth 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 098 331 SCREW, cap stl hexhd .750-10 x 5.000 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 098 332 NUT, stl slflkg hex reg .750-10 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21 098 330 HANDLE, steering gear 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
22 604 423 GRIP, handle .875 ID x 4.500 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BE SURE TO PROVIDE MODEL AND SERIAL NUMBER WHEN ORDERING REPLACEMENT PARTS.
-
1
-
2
Miller RUNNING GEA Owner's manual
- Type
- Owner's manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Miller KB000000 Owner's manual
-
-
-
Miller KA000000 Owner's manual
-
-
-
Miller KF000000 Owner's manual
-
-
-