Vax VRS1072 Owner's manual

Category
Vacuum cleaners
Type
Owner's manual

This manual is also suitable for

vax.co.uk
VRS107/VRS1071/VRS1072/
VRS108/VRS1081/VRS1082
Quicklite
Let’s get started
Let’s talk safety
Basic
safety
precautions
This vacuum cleaner is intended for household use only and
NOT for commercial or industrial use.
Only use the vacuum cleaner indoors on dry surfaces and
keep the area you’re cleaning well lit.
Keep ngers, hair and loose clothing away from moving parts
and openings whilst using the vacuum cleaner.
This vacuum cleaner can be used by children aged from
Don’ts
Don’t use the vacuum cleaner if it has been dropped,
damaged or left outdoors.
Don’t run over the power cord or use vacuum cleaner if the
power cord or plug is damaged. Please contact our Customer
Care Line on: 0330 026 8455 (Mon-Fri 8:30am to 6:30pm,
Sat 9:00am to 5:00pm).
Don’t handle the plug or use the vacuum cleaner with wet hands.
Don’t pull or carry the vacuum cleaner by the power cord.
Don’t use the power cord as a handle, pull the power cord around
corners, sharp edges or close a door over the power cord.
Don’t unplug the vacuum cleaner by pulling on the power cord.
Don’t vacuum up hard or sharp objects such as glass, nails,
screws or coins etc.
Do’s
Turn o all controls on the vacuum cleaner before
disconnecting or connecting the plug from the mains socket.
Always keep the power cord away from the brushes during
use. After use always wrap the power cord around the cord
clips provided.
Always make sure both the pre-motor/post-motor lters are
in place before use.
Always ensure the brushbar is switched o when using
the vacuum cleaner on the stairs and take extra care when
positioning the vacuum cleaner on the stairs.
Always switch o the vacuum cleaner before disconnecting
or connecting the hose and accessories.
8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the vacuum cleaner in a safe
way and understand the hazards involved. Children shall not play with the
vacuum cleaner. Cleaning and user maintenance shall not be made by
children without supervision.
Only Vax recommended tools should be used with the vacuum cleaner,
use of non-branded Vax accessories/tools will invalidate your warranty.
Don’t vacuum up any ammable or combustible materials (lighter uid, petrol,
kerosene etc) or use the vacuum cleaner in an area with explosive vapours
or liquid.
Don’t vacuum up hot coals, cigarette butts, matches or smoking hot burning
items or use in an area where there may be harmful uids (chlorine, bleach,
and ammonia drain cleaner).
Don’t attempt to remove blockages with sharp objects as this may cause
damage to the vacuum cleaner, remove blockages only as instructed in
this guide.
Don’t use the vacuum cleaner with incorrect voltage as this may result in
damage or injury to the user. The correct voltage is listed on the ratings label.
Keep all openings clear and free from debris as this may aect the
airow/suction.
Always replace the fuse in the plug with a British 13amp fuse.
Always protect the power cable from heated surfaces and open ames.
Use only CE approved 13amp extension cords, non-approved extension cords
may overheat. Care should be taken to arrange the extension cord as it can be
a trip hazard.
Store the vacuum cleaner in a cool, dry area. If the lters have been cleaned
as per user the guide instructions ensure they are thoroughly dry before
storing away.
PLEASE KEEP INSTRUCTIONS FOR FURTHER USE AND USE ONLY
AS INSTRUCTED IN THIS GUIDE
Thank you for buying this Quicklite.
Taking care of your carpets and hard oors
The Quicklite is designed to make vacuuming carpets and hard oors regularly, as eective
and ecient as possible and this user guide will help you get the most out of your machine.
Maintaining your carpets and hard oors will ensure they keep their appearance for longer.
You’ve chosen the carpets and hard oors for your home for a reason and Vax will help you
take good care of them.
Taking care of your Quicklite
Also inside this guide are instructions on maintaining your new machine, so that it’s always
ready when you are to tackle your carpets and hard oors.
Let us know what you think @VaxUK
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0330 026 8455 (ROI) 1-800 928 308
Monday-Friday 8:30am to 6:30pm, Saturday 9:00am to 5:00pm
Calls are charged at the UK local rate. Please make a note of the serial number and model number
of the product before calling.
Alternatively, you can write to us at:
Vax Ltd, Plot 302, Stonebridge Cross Business Park, Hampton Lovett, Droitwitch, WR9 OLW, UK
This User Guide can be found online at: vax.co.uk/support
Contents
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
Accessories
What to do if it goes wrong
Getting in touch
Quicklite
(Included with all models)
2-in-1 crevice tool
and dusting brush
Included with
your machine
Quicklite Pet
TurboTool holder
TurboTool
TurboTool connector
Hard oor adaptor
Initial Setup for normal operation
1. Use the base accessories.
Shortest hose
Extension tube set to shortest practicable length.
2. Clean lters installed.
3. Dust receptacle empty.
4. All Bleeds must be closed.
5. Floorheads/tools set to Carpet Mode for carpet cleaning.
6. Mechanical Agitation set turned ON for carpet cleaning.
7. Floorheads/tools set to Hard Floor Mode for hard oor cleaning.
8. Mechanical Agitation set turned OFF for hard oor cleaning.
Getting to know your machine
Handle
Hose
Cord wraps
Cord guide
Hose guide
Carry handle
2-in-1 crevice tool and
dusting brush
Separator
Dirt container
On/O button
HEPA lter
(hidden)
Brushbar height adjuster
Hard oor adaptor
Technical Specication
Name Quicklite
Voltage Please refer to product rating label on machine
Wattage Please refer to product rating label on machine
Capacity 2.4L
Cord length 7m
Weight 4.7kg (dependant on model)
Subject to technical change without notice.
Accessories & Consumables
Filter Kit (Type 94)*
1-1-134293-00
Belt Kit (Type 17)*
1-1-132048-00
TurboTool (Type 6)*
1-1-134419-00
*
To purchase consumables and accessories, please visit vax.co.uk
Getting started
*To purchase consumables and accessories, please visit vax.co.uk
Getting started
CAUTION: Always switch o the vacuum cleaner before connecting or disconnecting the hose/attachments,
or removing and emptying the dirt container.
IMPORTANT: The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner
does overheat the thermostat will automatically turn the vacuum cleaner o. If this happens, switch the
vacuum cleaner o and unplug. Remove and empty the dirt container also check the vacuum cleaner for
blockages. Allow the vacuum cleaner to cool for approximately 1 hour (if you have cleaned the lters please
wait 24 hours for the lters to fully dry before putting back into the machine). If the vacuum cleaner is blocked,
switch o and unplug before removing the blockage.
Assembling your vacuum cleaner
Using a crosshead
screwdriver, remove the
screw from the back of
the vacuum cleaner.
Slide the handle down
into the main body of the
vacuum cleaner.
Return the screw and
tighten, securing the
handle into the main body
of the vacuum cleaner.
Wrap the hose over the
hose guide. Line up tabs
on the lower hose
connector with the tabs
in the lower hose entry
point. Twist connector
clockwise and lock
into place.
Line up tabs on the upper
hose connector with the
tabs in the upper hose
entry point.
Twist connector clockwise
until clicks and locks
into place.
Attaching the TurboTool holder and TurboTool (Quicklite Pet only)
Line up TurboTool
holder with handle,
push TurboTool holder
onto handle until clicks
into place.
Line up TurboTool brush
into TurboTool holder,
push until it clicks
into place.
Place the 2-in-1 crevice tool
and dusting brush into the
tool holder.
Using your machine
Turn brushbar height
adjuster dial to
desired setting.
Plug vacuum cleaner into
the mains, switch on.
Use the hard oor adaptor for best results on hard oors.
The hard oor adaptor can be used on any oor setting on the height adjuster dial.
Place foot on oorhead
and pull handle
backwards to recline.
Press the On/O button
to switch on.
Using the hard oor adaptor
Lie the vacuum cleaner
on its back exposing
the brushbar.
Line up hard oor adaptor
with base of vacuum
cleaner. Push adaptor
onto base, until it clicks
into place.
To make sure the hard oor
adaptor is correctly tted,
the wheels on the adaptor
should be at the back when
attached to vacuum cleaner.
TIP
Using your machine
Choose an accessory. Twist lower hose
connector anti-clockwise
to unlock. Pull and
remove lower hose.
To use the dusting brush, press the tab and slide the dusting brush
forwards until it clicks into place.
Hold vacuum cleaner with brushbar over tread of stairs.
Use the hard oor adaptor for best results on hard oors. The hard oor adaptor can be used on any oor setting
on the height adjuster dial.
Attach TurboTool
connector to hose before
attaching TurboTool
(some models only).
Attach accessory to hose.
Using accessories
Using on the stairs
2-in-1 crevice tool and dusting brush
IMPORTANT: Always switch o the vacuum cleaner before disconnecting or connecting the hose and
accessories. The accessories can be attached directly to the hose. This vacuum cleaner is tted with a
constantly rotating brushbar. To avoid damage to your ooring, ensure the brushbar is raised to the highest
setting when using the accessories.
CAUTION
This vacuum cleaner has a
constantly rotating brushbar.
When cleaning on stairs raise
the height adjuster dial to the
highest setting. The brushbar
must over hang the stair tread.
Always take extra care when
cleaning stairs.
Taking care of your machine
IMPORTANT: The motor is equipped with a thermal cut-out. If for any reason the machine should overheat,
the thermostat will automatically turn the machine o. Switch o and unplug the vacuum cleaner. Check the
machine for blockages and clean the lters. Wash the lters with warm water (40°C max) and leave for 24
hours or until fully dry before replacing into the machine. Filters require cleaning at least every 3-6 months
(depending on the level of use). Don’t use your vacuum cleaner without all of the lters in place.
Emptying the dirt container
Press the dirt container release
button, pull and remove
dirt container.
Hold the dirt container over a bin.
Pull the dirt release clip, allowing
dirt/debris to fall out.
TIP
Don’t over ll the dirt container
to avoid blocking the air ow
through the vacuum cleaner
and replace lters every
6-9 months.
Taking care of your machine Taking care of your machine
Cleaning the separator
Cleaning the pre-motor lter
40 C max
24hr
Turn the separator
clockwise to remove from
the dirt container lid.
Turn the dirt container lid
anti-clockwise to unlock
and lift to remove.
Leave the lter to dry
for at least 24 hours.
Lift the pre-motor
lter out of the
central separator.
Tap excess dirt from
the lter and rinse
under a tap.
Turn the separator
clockwise to remove from
the dirt container lid.
Turn the dirt container lid
anti-clockwise to unlock
and lift to remove.
Tap separator over a bin
to remove any dirt/debris.
Using a soft brush clean
any dirt/debris out of
the separator.
Taking care of your machine
Re-tting the pre-motor lter and separator
Cleaning the post-motor lter
24hr
Remove any dirt/debris.
Rinse under water
(max 40°C).
Line up tabs on separator
with tabs in dirt container
lid. Turn clockwise until
separator clicks into place.
Lift to remove
post-motor lter.
Slide the pre-motor lter
into the central separator.
Leave to dry for 24
hours or until fully dry
before placing back in
the vacuum cleaner.
Line up the dirt container
lid with the dirt container.
Turn the dirt container lid
clockwise to lock.
The separator should
sit on seal in bottom of
dirt container when
correctly tted.
Don’t use your vacuum
cleaner without all of the
lters in place.
IMPORTANT
Let’s talk technical
IMPORTANT: Unplug and switch o vacuum cleaner before performing maintenance or
troubleshooting checks.
Removing debris from brushbar
Removing dirt/debris from TurboTool (Quicklite Pet only)
Locking ring
Tabs
Locking ring
Tabs
Locking ring
Tabs
Slide the locking ring to remove.
Using a pair of scissors remove any threads
or hair caught around the brushbar.
Lift and separate the housing.
Using a pair of scissors remove
any threads or hair caught around
the brushbar.
Line up the tabs on front of housing
and re-t. Slide locking ring into
groove to secure.
IMPORTANT: If the brushbar does not rotate easily then the belt may not have been tted correctly. Make sure
the belt is not twisted.
Replacing the belt
Removing a blockage from the hose
Twist upper hose
connector anti-clockwise
and remove upper hose.
Twist lower hose
connector anti-clockwise
to unlock. Pull and remove
lower hose.
Remove any blockage
by inserting wire coat
hanger into hose.
TIP
To test for a blockage in
hose, drop a small ball of
paper through the hose.
The paper will drop through
if the hose is clear.
Lift to remove brushbar
cover from base of
vacuum cleaner.
Lie vacuum cleaner on its
back exposing brushbar.
Use a crosshead
screwdriver to remove
6 screws.
Lift to remove brushbar.
Remove and dispose of
old belt. Clean any debris
from spindle and place
new belt onto spindle.
Place belt on rounded
area of brushbar without
bristles. Line up right side
of brushbar with base,
push into place. Lift and
push left side of brushbar
until clicks into place.
Let’s talk technical
Accessories
Dont forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
Pro Cleaning Kit (Type 2)
1-1-133326-00
All our best tools all in one kit that makes cleaning your
home quicker, easier and with even better results.
We’ve taken care of cleaning all of the hard to reach areas
such as on top of cupboards and in between blinds to the
dust that collates behind and within the radiator.
TurboTool (Type 6)
1-1-134419-00
Use the TurboTool for vacuuming your stairs, upholstery
and car interiors. It’s great for picking up stubborn pet hair.
What to do if it goes wrong
Check the ‘This pack contains’ panel on the box to make sure the part
is included with your vacuum cleaner.
The plug may not be fully pushed into the electrical socket.
Check the fuse in the plug if this needs replacing, always replace with a
13amp fuse.
The motor thermostat may have tripped. If this has happened, unplug the
vacuum cleaner. Remove and empty the dirt container and check the hose
for blockages. Clean the lters and allow the vacuum cleaner to cool for
approximately 1 hour (if you have washed the lters you will need to wait
24 hours for the lters to fully dry before putting them back into the
vacuum cleaner).
The brushbar may be clogged, check the brushbar and clear any hair
or debris. Go to ‘Let’s talk technical’.
The belt may be broken. Go to ‘Let’s talk technical’.
Empty the dirt container and clean lters. Go to ‘Taking care of your machine’.
There may be a blockage in the hose. Please remove the hose from the
vacuum cleaner, check and clear any blockages. Go to ‘Let’s talk technical’.
The brushbar may not be turning. Go to my brushbar isn’t turning below.
The brushbar height adjuster dial may not be set to the correct setting.
Go to ‘Using your machine’.
Make sure the hard oor adaptor is attached/unattached dependant on the
oor surface.
If the accessory/tool will not pick up, check and clear any blockages.
Go to ‘Let’s talk technical’.
SolutionProblem
Is there an accessory
missing?
Why does my vacuum
cleaner have no power?
Why won’t the vacuum
cleaner pick up?
My brushbar
isn’t turning?
Getting in touch
CAUTION: To reduce the risk of personal injury, unplug the vacuum cleaner before performing maintenance
/troubleshooting checks.
Getting in touch
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the product before calling.
Registration required. Terms and conditions apply, see vax.co.uk for details.
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility,
declare that the VRS (107/1071/1072/108/1081/1082) is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
© 2014 All rights reserved. VAX®, VAX Lozenge, are trade marks or registered trade marks of Techtronic Floor Care Technology Ltd.
@VaxUK
Vax Ltd., 5th Floor 2 Colmore Square, 38 Colmore Circus, Queensway, Birmingham, B4 6BN, UK
email: inf[email protected] website: vax.co.uk
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18

Vax VRS1072 Owner's manual

Category
Vacuum cleaners
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI