Rust-Oleum RockSolid 286893 Operating instructions

Brand: Rust-Oleum RockSolid

Model: 286893

Type: Operating instructions

RockSolid

Metallic

Garage Floor Coating

TURN A BORING, BLANK SPACE INTO A MODERN DAY CANVAS

Visit www.homedepot.com/rustoleum for

other great ideas, products and inspiration.

Shown with

RockSolid

Metallic Floor Coating Kit

Copper Pot

STEPS

1. PREPARE CONCRETE SURFACE: Scrub heavily-soiled areas with a heavy-duty degreaser and then etch entire

oor with concrete etch (included), rinse thoroughly & allow to dry completely.

2. BURST-SHAKE-POUR: Roll side A of Polycuramine pouch toward side B, burst and mix the two parts. Shake

well for 2-3 minutes. Cut one corner and pour contents into mixing bucket.

3. MIX IN METALLIC POWDER: Add metallic tint to bucket. Mix with paddle mixer and drill for 2-3 minutes until

thoroughly mixed.

4. APPLY COATING: Trim outer edges with a brush and then begin to apply the coating in 5’ x 5’ sections. Tip:

After rolling out each section, use the roller to put circular patterns in the coating (like applying wax to a car) to

ensure there are no bare spots. This will give the coating an opaque appearance once dry. See instructions for

working time of product after mixing.

5. Repeat the above steps for each additional pouch. Mix only one pouch at a time.

RockSolid Dry Time: Temperature and humidity may affect drying time. Do not walk on coating while it is still tacky. Surface

should be ready for foot trafc in 8-10 hours and vehicle trafc in 24-36 hours, depending upon temperature and humidity.

Always thoroughly review directions on package before using any product.

Completely transform your garage from a messy storage room into an inspiring functional space.

Optional

• Anti-skid additive

• Heavy-duty degreaser

• Concrete Patch and Repair Product

• Paddle mixer

• Drill

ITEMS

• RockSolid

Metallic Floor

Coating Kit-(Kit

contains: Concrete Etch,

3/8”nap Polyamide Roller,

Metallic tint, Polycuramine

burst pouch, instructions and

stir stick)

• 9” Roller frame

• Roller extension pole

• Stiff bristled broom brush

• 3” paint brush

• Mixing bucket

RockSolid®MetallicFloorCoating

APPLYROCKSOLID®OVERTILETOGIVEITASPARKLINGNEWLOOK

Step1:Deglazeentiretilesurfaceusing60to80gritsandpaperonapole

ororbitalsander.Vacuumallsandingdustfromsurfaceusingashopvac.

Thisstepisveryimportant.

Step2:CleanentiresurfaceusingAcetoneorDenaturedAlcohol.Rinse

i d l t LtD

ITEMSNEEDED

• RockSolid®MetallicFloorCoatingKit

(Kitcontains:ConcreteEtch,3/8”nap

PolyamideRoller,Metallictint,

• ShopVac

• Mop&Bucket

• MixingBucket

ngamopan

c

eanwa

er.



ry.

Step3:Burst‐Shake‐Pour. RollSideAofPolycuramine®pouchtoward

SideB.Burstandmixthetwoparts.Shakewellfor2‐3minutes,cutone

cornerandpourcontentsinmixingbucket.

Polycuramineburstpouch,instructions

andstirstick)

• RockSolid®ClearTopcoat(optional)

• 60to80gritsandpaper

• PoleSanderorOrbitalHandSander

• AcetoneorDenaturedAlcohol

• PaddleMixer

• 9”RollerFrame

• RollerExtensionPole

• 3”PaintBrush

Step4:MixinMetallicTint.Addmetallictinttobucketofliquidandmix

withapaddlemixerfor2‐3minutesuntilthoroughlymixed.

Step5:ApplyCoating.Trimouteredgesusingabrushandthenbeginto

applycoatingin5’x5’sections.Tip:Afterrollingouteachsection,usethe

rollertoputcircularpatternsincoating(likeapplyingwaxtoacar)to

ensuretherearenobarespots.Seeinstructionsforworkingtimeof

productaftermixing.

Step6:ApplyRockSolidClearCoat(optional) foraddedprotectionand

l F li

it t f dd ti

kid dditi i t

BEFOREBEFORE

AFTERAFTER

oss.

oras

p‐res

sur

ace,a

an

‐s

kid

a

dditi

vepr

or

o

application.Thisisespeciallyrecommendedforhighmoistureareaslike

bathrooms.

Alwaysthoroughlyreviewinstructionsbeforeusinganyproduct

Tip:

For an extra smooth look

se RockSolid

Clear Topcoat

as a

“

primer coat

”

Tip:



For



extra



smooth



look

,



RockSolid



Clear



Topcoat



primer



coat



firsttofillingroutlines,followedbyRockSolid®MetallicFloorCoating. Foralook

withvisiblegroutlines,applyRockSolid®Metallicdirectlyontopreppedtile.

*ForHorizontalSurfacesOnly

*Coveragerateswillbereducedduetoporosityofthetilesubstrate.

Asshown,RockSolid MetallicBrown

RockSolid®MetallicFloorCoating

A NEW LOOK FOR WOOD FLOORS WITH

ROCKSOLID

Step1:Sandentirewoodsurfaceusing80gritsandpaperonapole

sanderororbitalhandsander.

Step 2: Remove sanding dust from surface

using a tack cloth It is



NEW



LOOK



FOR



WOOD



FLOORS



WITH



ROCKSOLID

Step





Remove



sanding



dust



from



surface



using



tack



cloth

.



importantthatalldustisremovedpriortoapplyingthecoating.

Step3:Burst‐Shake‐Pour. RollSideAofPolycuramine pouchtoward

SideB.Burstandmixthetwoparts.Shakewellfor2‐3minutes,cut

onecornerand

ourcontentsinmixin

bucket.

ITEMSNEEDED

• RockSolid®MetallicFloorCoatingKit

(Kitcontains:ConcreteEtch,3/8”nap

PolyamideRoller,Metallictint,

•9”rollerframe

•Rollerextensionpole

•3”paintbrush

p g

Step4:MixinMetallicTint.Addmetallictinttobucketofliquid.

Mixwithapaddlemixerfor2‐3minutesuntilthoroughlymixed.

Step5:ApplyCoating.Trimouteredgesusingabrushandthen

bi l i i 5’ 5’ i Ti Af lli h

Polycuramineburstpouch,instructions

andstirstick)

•RockSolidClearCoatingKit(optional)

•80gritsandpaper

•PoleSander

•ShopVac

•

Tack Cloth

• ShopVac

• Mop&Bucket

• MixingBucket

• PaddleMixer

• 9”RollerFrame

• RollerExtensionPole

•

3” Paint Brush

ntoapp

ycoat

ng

n

5’

x

5’

sect

ons.

p:

terro

lli

ngouteac



section,usetherollertoputcircularpatternsincoating(like applying

waxtoacar)toensuretherearenobarespots.

Step6:ApplyRockSolidClearTopcoat(optional) foradded

protection and gloss For a slip

‐

resistant surface add anti

‐

skid

•

Tack



Cloth

•MixingBucket

•PaddleMixer

•

3”



Paint



Brush

AFTERAFTER

BEFOREBEFORE

protection



and



gloss

.

For



slip

resistant



surface

,

add



anti

skid



additivepriortoapplication.Thisisespeciallyrecommendedforhigh

moistureareaslikebathrooms.

Alwaysthoroughlyreviewinstructions beforeusinganyproduct.

*ForHorizontalSurfacesOnly

*Coveragerateswillbereducedduetoporosityofthetilesubstrate.

Asshown,RockSolid MetallicBrown

Rust-Oleum RockSolid 286893 Operating instructions

Brand: Rust-Oleum RockSolid

Model: 286893

Type: Operating instructions

Download PDF

report

Rust-Oleum RockSolid 286893 Operating instructions

Rust-Oleum RockSolid 286893 Operating instructions

Related papers

Other documents