Parkside PDSP 1000 B2 Operating instructions

IAN 43089

PISTOLET DE SABLAGE A AIR COMPRIMÉ

PDSP 1000 B2

PISTOLET DE SABLAGE A AIR

COMPRIMÉ

Traduction du mode d‘emploi d‘origine

DRUCKLUFT-SANDSTRAHLPISTOLE

Originalbetriebsanleitung

AIR SANDBLASTER GUN

Translation of original operation manual

CV_43089_PDSP1000B2_LB2.indd 3 19.08.14 14:42

Page is loading ...

17

PDSP 1000 B2

GB

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Technical details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

General safety notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Device-speciﬁ c safety instructions for compressed air sandblasters . . . . . . . . . . . . . . . . . . . . . 19

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting the compressed air supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Filling the blasting medium container . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Mount the collecting bag for sandblasting material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Select and ﬁ tting attachments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Using the compressed air sandblaster gun. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Collecting bag for sandblasting material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Importer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Translation of the original Conformity Declaration . . . . . . . . . . . . . . . . . . . . . 24

IB_43089_PDSP1000B2_LB2.indb 17 19.08.14 14:49

18

PDSP 1000 B2

GB

AIR SANDBLASTER GUN

PDSP 1000 B2

Introduction

Congratulations on the purchase of your

new appliance. You have selected a high-

quality product. The operating instructions

are part of this product. They contain important in-

formation about safety, use and disposal. Before

using the product, familiarise yourself with all

operating and safety instructions. Use this product

only as described and only for the speciﬁ ed areas

of application. Please also pass these operating

instructions on to any future owner(s).

Proper use

The PDSP 1000 B2 sandblaster gun (hereinafter

appliance) is suitable for: the removal of rust and

paint from metal surfaces. Any other usage of or

modiﬁ cation to the appliance is deemed to be

improper usage and carries the risk of serious per-

sonal injury. The manufacturer accepts no responsi-

bility for damage(s) resulting from improper usage.

This appliance in intended only for domestic use.

Features

Air sandblaster gun

Nipple for air connection

Trigger

Collecting bag for sandblasting material

Screw clamp

Jet nozzle

Control dial (1/0)

Blasting medium container

Screw cap

Surface attachment

Point attachment

Outer edge attachment

Inner edge attachment

Blasting medium

Package contents

1 air sandblaster gun PDSP 1000 B2

1 surface attachment

1 point attachment

1 edge attachment

1 interior corner attachment

1 collecting bag for sandblasting material

1 screw clip

2 kg blasting medium

1 operating manual

Technical details

Max. working pressure: 6.3 bar

Air consumption:

max. 260 l/min

Container capacity: 900 ml

Volumetric ﬂ ow rate: 200–220 g/min

Required air quality: cleaned and oil-free

Setting value for working working pressure on the

pressure reducer or ﬁ lter

pressure gauge set to

6.3 bar.

Noise and vibration data:

Noise measurement determined in accordance

with EN 1265. The A-rated noise level of this

compressed-air tool is typically:

Sound pressure level: 90,5 dB(A)

Sound power level: 101,5 dB(A)

Uncertainty K: 3 dB

Wear ear protection!

Vibration emission value: ≤ 2,5 m/s

2

Values determined in accordance with

EN ISO 28927

WARNING!

IB_43089_PDSP1000B2_LB2.indb 18 19.08.14 14:49

19

PDSP 1000 B2

GB

WARNING!

► The vibration level speciﬁ ed in these instruc-

tions has been measured in accordance with

the standardised measuring procedure speci-

ﬁ ed in EN ISO 28927 and can be used to

make equipment comparisons. The speciﬁ ed

vibration emission value can also be used to

make an initial exposure estimate.

The vibration level varies in accordance with

the use of the compressed air tool and may

be higher than the value speciﬁ ed in these

instructions in some cases. It is easy to under-

estimate the vibration load if the compressed

air tool is used regularly in a certain manner.

NOTE

►

For an accurate estimate of the vibration load

during a certain working period, the times

during which the appliance is switched oﬀ or

is running but not actually being used must

also be taken into consideration. This can

signiﬁ cantly reduce the vibration load over

the total working period.

General safety notices

WARNING!

► Read all safety warnings and all instructions.

Failure to follow the warnings and may result

in electric shock, ﬁ re and/or serious injury.

Save all warnings and instructions for future

reference!

Workplace safety

a) Keep your working area clean and well lit.

Cluttered and dark areas invite accidents.

b) Do not operate tools in explosive atmospheres,

such as in the presence of ﬂ ammable liquids,

gases or dust. Tools can create sparks which

may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a tool. Distractions can cause you

to lose control.

Device-speciﬁ c safety instructions for

compressed air sandblasters

■ Check the appliance for any possible defects

before use. If the appliance exhibits any faults,

it should not be used under any circum-

stances.

■ Keep children and bystanders away while

operating the tool. Distractions can cause

you to lose control.

■ RISK OF INJURY! MISUSE! Do not point the

tool towards people or animals!

■ Wear a dust mask.

■ Wear safety goggles!

■ Wear protective gloves!

■ RISK OF EXPLOSION! The compressed air

sandblaster gun should not be used in areas

with gas/open ﬂ ames/ﬁ re/gas-operated

water heaters.

■ SMOKING PROHIBITED!

■ Work only in suﬃ ciently ventilated rooms.

■ Do not use oxygen or any combustible gas

as an energy source.

■ Never exceed the maximum operating pres-

sure of 6.3 bar.

WARNING!

► KICKBACK FORCES! At high working pres-

sures, kickback can occur which can, under

certain circumstances, lead to danger due to

continuous loads.

■ RISK OF INJURY! Disconnect the appliance

from the compressed air source before starting

any repairs or maintenance work and before

transportation.

■ RISK OF INJURY! Disconnect the appliance

from the compressed air source before reﬁ lling

the blasting medium.

NOTE

►

Please heed the safety instructions provided

by the manufacturer of the blasting medium.

IB_43089_PDSP1000B2_LB2.indb 19 19.08.14 14:49

20

PDSP 1000 B2

GB

■ Use only materials that are suited for use in the

compressed air sandblaster gun . Do not

use quartz sand. This can lead to a dangerous

build-up of silicosis-inducing dust.

■ Take steps to ensure that others are not incon-

venienced (dust formation).

■ Ensure that the blasting medium is collected so

that it can be disposed of in an environmentally

friendly manner.

■ Do not remove any type plates. These contain

important information for the safe operation of

the appliance.

■ If you are inexperienced with the appliance,

seek training in how to use it safely.

WARNING! TOXIC DUST!

► Working with harmful/toxic dusts results in

health hazards for the person operating the

appliance and for other persons in the area.

Operation

Connecting the compressed air supply

NOTE

►

The compressed air sandblaster gun may

only be operated on cleaned, condensate-

and oil-free compressed air and may not

exceed the maximum operating pressure of

6.3 bar at the appliance.

To ensure that you can regulate the air pres-

sure, the compressed air source should be

equipped with a (ﬁ lter) pressure reducer.

♦ Connect the compressed air sandblaster gun

to a suitable compressed air source by attaching

the quick-connect coupling of the supply hose to

the nipple on the sandblaster gun .

The connection locks automatically.

NOTE

►

Ensure that the control dial is set to "0"

before connecting the appliance to the com-

pressed air source.

Filling the blasting medium container

CAUTION!

► Before you open the screw cap on the

blasting medium container

, or make any

other settings, the connection to the com-

pressed air hose must be disconnected and

all pressure completely discharged.

■ Use only suitable blasting medium for your

sandblasting work.

NOTE

►

We recommend using a blasting medium

(ground blast furnace slag) with a grain size

of 0.2 mm–0.8 mm and which has been

shown not to cause silicosis.

■ Please ensure that the blasting medium is

totally dry and not too coarse-grained.

NOTE

►

The maximum grain size is 0.8 mm!

■ Open the screw cap on the blasting medium

container by turning it anti-clockwise.

■ Fill the required amount of blasting medium

into the blasting medium container .

■ Ensure that you do not exceed the maximum ﬁ ll

level for the container of 900 ml.

■ Afterwards, close the screw cap on the blast-

ing medium container by turning it clockwise.

NOTE REGARDING THE GRAIN SIZE OF

THE BLASTING MEDIUM

►

The larger/coarser the grain size of the blasting

medium used, the coarser the dirt that can be

removed using it. The supplied material, on

the other hand, is ﬁ ne and thus more suitable

for the removal of items such as paint or rust

ﬁ lm. The ﬁ ne material also causes less dam-

age to the surfaces being treated, meaning a

choice can be made regarding these.

For coarse rust, for example, it is best to use

a coarse-grained blasting medium which you

can order online (see Chapter "Importer") or

in any good specialist retailer. Please observe

the guidelines regarding maximum grain size.

IB_43089_PDSP1000B2_LB2.indb 20 19.08.14 14:49

21

PDSP 1000 B2

GB

Mount the collecting bag for sand-

blasting material

■ Use a screwdriver to attach the collecting bag

to the appliance with the supplied screw

clip

.

Select and ﬁ tting attachments

■ Start by selecting the appropriate attachment

for the job at hand (

, , ,

).

■ Push the selected attachment ﬁ rmly onto the jet

nozzle , ensuring that no air can escape from

the sides.

Using the compressed air sand-

blaster gun

■ Carefully prepare the workpiece that is to be

blasted. Clean it if need be.

NOTE

►

Layers of dust or fat will signiﬁ cantly impair

the results.

■ Carefully cover or mask everything that is not to

be blasted.

■ The distance between the attachment and the

surface being worked plays an important role

and should be kept as low as possible so that

the blasting medium can be collected by the

collecting .

■ The nearer you are to the workpiece, the smaller

the dispersion pattern and vice versa.

■ Do a test run on an old workpiece to ﬁ nd out

the correct distance/working pressure and avoid

excessive reﬂ ection from your workpiece.

Switching on:

■ Set the control dial to "1" to open the air

outlet.

■ Move the compressed air sandblaster

close

to the area to be worked.

■ Press the trigger to start operating the com-

pressed air sandblaster gun .

Switching oﬀ :

■ Release the trigger to switch oﬀ of the com-

pressed air sandblaster gun .

■ Set the control dial to "0" to close the air

outlet.

■ Disconnect the appliance from the compressed

air source after you ﬁ nish work.

NOTE

►

First detach the hose from the compressed air

source before disconnecting the supply hose

from the appliance.

In this way you avoid uncontrollable thrashing

about of the supply hose.

Collecting bag for sandblasting

material

NOTE

►

Do not re-use surplus sand-blasting material

from the collecting bag until it has been

cleaned.

■ You can remove the surplus sand-blasting material

that has collected in the collecting bag via

the zip fastener or use a screwdriver to undo

the screw clamp and remove the collecting

bag from the appliance.

IB_43089_PDSP1000B2_LB2.indb 21 19.08.14 14:49

22

PDSP 1000 B2

GB

Troubleshooting

Fault/possible cause Remedy

No material ﬂ ow

The air is not dry

enough.

Install a water separator

in your compressed air

system.

Air pressure too low

Increase the output

pressure of your com-

pressor.

Attachment not sitting

correctly

Ensure that the attach-

ment is ﬁ rmly on the

appliance and that

no air escapes at the

sides.

Blocked sand-blasting

material pipes

Check that no lumps of

sandblasting material

are blocking the pipes.

Preferably use a

blow-oﬀ gun to clean

blocked pipes.

(Wear protective

glasses!) Also check

the outlet opening of

the tank.

Sand-blasting pattern not as expected

The air is not dry

enough.

Install a water separ-

ator in your com-

pressed air system.

Grain size of the sand-

blasting material not

uniform

Replace sand-blasting

material.

Sand-blasting material

impure

Clean/replace sand-

blasting material

The attachment is worn

out

Replace the attach-

ment

Other defects

Please contact an expert or your retailer.

Components

(see back fold-out page)

Item no. Description Amount

01 Housing 1

02 Screw 2

03 Screw 1

04 O-ring 1

05 Pin 1

06 Air valve spring 1

07 O-ring 1

08 Screw nut 1

09 Spring 1

10 Trigger 1

11 Air inlet 1

12 Socket 1

13 Nozzle 1

14 O-ring 2

15 Beaker ring 1

16 Connecting piece 1

17 Nozzle 1

18 Control lever 1

19 O-ring 1

20 Connection lever 1

21 Pin 1

22 Adjusting knob 1

23 Screw 1

24 Container 1

25 Screw nut 1

26 O-ring 1

27 Protective cover 1

28 Screw 1

29 Screw cap 1

30 Handle cover 1

31 Nozzle 1

32 Nozzle 1

IB_43089_PDSP1000B2_LB2.indb 22 19.08.14 14:49

23

PDSP 1000 B2

GB

Item no. Description Amount

33 Nozzle 1

Maintenance and Cleaning

WARNING! RISK OF INJURY!

ALWAYS disconnect the appliance

from the compressed air supply

before cleaning it.

■ Clean the compressed air sandblaster gun

and the blasting medium container imme-

diately after completing your work. To do this,

blow out the compressed air sandblaster gun

and the blasting medium container

with

compressed air.

■ Store the compressed air sandblaster gun

only in dry rooms.

Disposal

The packaging is made from environmen-

tally friendly material and can be

disposed of at your local recycling plant.

Do not dispose of the appliance in

the normal domestic waste.

Your local community or municipal authorities can

provide information on how to dispose of the worn-

out appliance.

Warranty

The warranty for this appliance is for 3 years from

the date of purchase.

The appliance has been manufactured with care

and meticulously examined before delivery.

Please retain your receipt as proof of purchase. In

the case of a warranty claim, please make contact

by telephone with our Customer Service Depart-

ment.

Only in this way can a post-free despatch for your

goods be assured.

NOTICE

►

The warranty covers only claims for mate-

rial and manufacturing defects, but not for

transport damage, wearing parts or for

damage to fragile components, e.g. buttons

or batteries.

This product is for domestic use only and is not

intended for commercial use.

The warranty is void in the case of abusive and

improper handling, use of force and internal

tampering not carried out by our authorised service

branch.

Your statutory rights are not restricted in any

way by this warranty. The warranty period is not

extended by repairs made under the warranty. This

applies also to replaced and repaired parts.

Damages and defects extant at the time of pur-

chase must be reported immediately after unpack-

ing, resp. no later than two days after the date of

purchase.

Repairs made after the lapse of the warranty

period are subject to charge.

Service

Service Great Britain

Tel.: 0871 5000 720 (£ 0.10/Min.)

E-Mail: [email protected]

IAN 43089

Hotline availability: Monday to Friday from

8:00 to 20:00 (CET)

Importer

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

GERMANY

www.kompernass.com

IB_43089_PDSP1000B2_LB2.indb 23 19.08.14 14:49

24

PDSP 1000 B2

GB

24

PDSP 1000 B2

Translation of the original

Conformity Declaration

We, KOMPERNASS HANDELS GMBH, documents

oﬃ cer: Mr. Semi Uguzlu, BURGSTR. 21, 44867

BOCHUM, GERMANY, hereby declare that this

product complies with the following standards,

normative documents and the EC directives:

Machinery Directive

(2006 / 42 / EC)

Applied harmonised standards:

EN 1248: 2001+A1

EN ISO 4414: 2010

Type designation of machine:

Air sandblaster gun PDSP 1000 B2

Year of manufacture: 04 - 2014

Serial number: IAN 43089

Bochum, 02/01/2014

Semi Uguzlu

- Quality Manager -

Subject to technical changes in the course of

further developments.

IB_43089_PDSP1000B2_LB2.indb 24 19.08.14 14:49

2

IAN 43089

KOMPERNASS HANDELS GMBH

BURGSTRASSE 21

44867 BOCHUM

DEUTSCHLAND / GERMANY

www.kompernass.com

Version des informations · Stand der Informationen

Last Information Update:

05 / 2014 Ident.-No.: PDSP1000B2-052014-2

CV_43089_PDSP1000B2_LB2.indd 2 19.08.14 14:42

Parkside PDSP 1000 B2 Operating instructions

Related papers

Other documents