Design House 525725 User manual

Design House
Brand
Design House
Model
525725
Category
Sanitary ware
Type
User manual

This manual is also suitable for

7
7A
7B
7C
Set Screw
Pull-out Spayer Weight
Handle
Cartridge
Bonnet
Cap
Connect
8
2 3a 3b
3A
3B
3B
3A
54 6
6A
6B
4C
4A
4B
5B
5A
• ALWAYS protect your eyes with safety glasses.
SAFETY TIPS
IMPORTANT POINTS
Helpful tools to install this faucet:
•
basin wrench
•
Teflon tape
•
(2) crescent wrenches
•
silicon sealer
•
flashlight
•
faucet supply tubes
Models 525725, 525717
For Single Hole or Tri Hole Sinks
SINGLE HANDLE
PULL-OUT
KITCHEN FAUCET
Design House is a registered
brand of DHI Corp.
Mequon, WI 53092
1-800-558-8700
Your new Design House faucet will give you years of trouble free performance.
Thank you for choosing a Design House product for your home.
Please read all of these instructions carefully before installing your new faucet.
• When installing your new faucet, hand tighten the connector nuts, then use one wrench to anchor
the fitting and a second wrench to tighten the nut one additional turn. Connections that are too tight
will reduce the integrity of the system.
• Wrap all threaded connections (except aerator thread in spout) with Teflon tape available from your
local hardware or plumbing supply store. Always wrap in a counter-clockwise direction.
INSTALLATION PROCEDURE
2. Optional Escutcheon
Installation. Shut off water
supplies. Remove old faucet.
Install escutcheon over the
three holes in the sink.
From underneath sink, hand
tighten mounting nut. Do not
overtighten. Proceed to Step
(3A).
3a. Optional Escutcheon
Installation. Retract pull-out
hose (3A) up through faucet
body, until the pull-out hose
fitting is flush with the bottom
of shank (3B). Do not pull
hose fitting past the shank.
Insert faucet body through
the hole in escutcheon.
Note: Do not feed the pull-out
hose (3A) back down
through the spout until
step 5.
3b. Optional Flange Installation.
Retract pull-out hose (3A) up
through faucet body, until the
pull-out hose fitting is flush
with the bottom of shank
(3B). Do not pull hose fitting
past the shank. Insert faucet
body through the hole.
Note: Do not feed the pull-outhose
(3A) back down through
the spout until step 5.
1. This faucet can be installed as 3 hole installation with the escutcheon or as 1 hole installation with
flange. If using escutcheon, begin with step 2. If using flange, begin with step 3b.
4. Install rubber washer
(4A), metal washer
(4B) onto the threaded
mounting shank.
Thread nut (4C) onto
mounting shank.
Do not overtighten.
5. Screw quick connector
(5B) to the free end of
pull-out hose (5A).
6. Align block (6A) and tabs on quick connect.
Push quick connect housing firmly upward
and snap onto receiving block.Pull down
moderately to ensure connection has been
made.If it is necessary to remove quick
connect, squeeze tabs on hose between
index finger and thumb,then pull down to
disconnect.After connecting the hose,
install the weights at the lowest point of the
hose (6B).
INSTALLATION PROCEDURE
MAINTENANCE
7. Make connections to water lines. Use 1/2" I.P.S.
faucet connections (7A) or use supplied coupling
nuts (7C) with 3/8"" O.D.ball-nose riser (7B). Use
wrenches to tighten connections.
Do not overtighten.
8. Turn on hot and cold water supplies.
Pull the hose assembly out of the spout and
remove the spray head by unscrewing it from
the hose counterclockwise. Be sure to hold the
end of the hose down into the sink and turn the
faucet on to the warm position where it mixes
hot and cold water. Flush water lines for one
minute. Check for leaks. Re-tighten any
connections if necessary, but do not overtighten.
Reinstall spray head by hand tightening it back
onto the spray hose.
Under the Safe Drinking Water Act, the U.S. Environmental Protection Agency restricts the
amount of lead used in brass and solder. Your new faucet is made in strict compliance with
all government standards. The materials used in the manufacture of this faucet are of industry
standard quality and are similar to other plumbing products having brass fittings.
To reduce the amount of lead in your drinking water, allow the water to run for a moment before
filling your glass and remember to always use cold water for drinking purposes.
CONSUMER PROTECTION WARNING
Your new Design House faucet is designed to give you years of trouble free performance. Keep it
looking new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh
chemicals that will dull the finish and void your warranty.
Brass finishes are polished, then protected with a lacquer coating to help prevent tarnishing. Clean
these surfaces only with a damp, soft cloth.
TROUBLE SHOOTING
Problem: Leaks from under handle and water
does not completely shut off.
Cause: Bonnet is loose or the cartridge is dirty
or worn.
Action:
1. Remove the handle by loosening the set screw
with a phillips screwdriver and unscrew cap.
2. Tighten the bonnet by turning it clockwise.
Move the cartridge stem to the ON position.
The leak should stop around the cartridge
stem.
3. If the leak does not stop, shut off the water
supply. Remove the bonnet by turning it
counter clockwise.
Lift out the cartridge. Clear or replace the
cartridge if it is dirty or distorted.
4. Position the cartridge back to the faucet body
and retighten the bonnet and cap.
5. Reinstall the handle.
Many of these parts come preassembled.
This exploded diagram is to assist in trouble
shooting.
Page is loading ...
  • Page 1 1
  • Page 2 2

Design House 525725 User manual

Design House
Brand
Design House
Model
525725
Category
Sanitary ware
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents