Real Flame 3150-LO User guide

Category
Fireplaces
Type
User guide

Real Flame 3150-LO is a gel fireplace and accessory designed for indoor use, eliminating the need for ventilation. It features a sturdy construction with various components, including panels, supports, and trim, that can be assembled to create a stylish and functional fireplace. The included hardware kit facilitates the assembly process, and the provided instructions guide you through each step to ensure a proper installation.

Real Flame 3150-LO is a gel fireplace and accessory designed for indoor use, eliminating the need for ventilation. It features a sturdy construction with various components, including panels, supports, and trim, that can be assembled to create a stylish and functional fireplace. The included hardware kit facilitates the assembly process, and the provided instructions guide you through each step to ensure a proper installation.

Model # 3150
Camden Fireplace
Lot:___________
3150-Camden-JW-081511
gel replaces and accessories
Mantle Assembly Instructions
2
Dust the mantel periodically as you would with any piece of furniture.
Using a soft cloth and a wood cleaner, wipe the mantel clean in the direction of the grain to minimize the
appearance of scratches and scus in the nish.
Do not use water to clean mantel. Water may cause swelling, warping or stains if allowed to penetrate the
nish of the mantel. Use protective pads or cloths whenever possible.
Avoid placing mantel in rooms with lots of humidity or where humidity could be a problem. This may cause
warping to the mantel.
Avoid direct sunlight if possible to reduce the possibility of fading the nish.
Using your Fireplace
Fireplace is designed to be used indoors, there is no need for ventilation.
Use extreme caution while burning. Some surfaces become extremely hot during use.
Before using replace, be sure you have read and understand the step-by-step instructions and warnings
included with your Gel fuel or electric rebox.
Care and Cleaning
Helpful Tips for Assembly
Before assembly carefully unpack and check for each replace piece and necessary hardware
IF ANY PARTS ARE DAMAGED OR MISSING PLEASE CALL US DIRECTLY AT:
1-800-654-1704
Prep, plan and clear your space. In order to minimize damage while assembling make sure unpacking and
assembly takes place on a carpeted surface.
We recommend to use a power screwdriver for assembly it will greatly reduce your time for assembly. BE SURE
NOT TO OVERTIGHTEN SCREWS. The wood can easily be stripped out if too much force is used.
Use two people for assembly of the mantle. Another set of hands will help tremendously with the assembly
process and will reduce the amount of time spent on assembly. If you do not have a helper, that is ok too, just
take your time and follow the instructions.
Make sure that your mantle has been properly assembled prior to use. Once you have completed assembly
you should not have any extra mantle parts. The piece will be quite sturdy and all pieces will t together
nicely. If you did not achieve ideal results by following the instructions, please contact our customer service
team at 1-800-654-1704 and they will help answer any questions or concerns about the assembly process.
3
PARTS LIST
#15 HARDWARE LIST - 31500015
A x 32
Short Allen Screw
B x 16
L-Bracket
C x 27
Long Allen Screw
D x 19
Washer
E x 1
Allen Wrench
F x 2
MDF Board
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Number Description Mahogany Light Oak Quantity
1 Base Panel 31500401 31500601 1
2 Left Side Panel 31500402 31500602 1
3 Right Side Panel 31500403 31500603 1
4 Left Front Panel 31500404 31500604 1
5 Right Front Panel 31500405 31500605 1
6 Lower Firebox Trim 31500406 31500606 1
7 Center Panel 31500407 31500607 1
8 Top Front Panel 31500408 31500608 1
9 Top Center Panel 31500409 31500609 1
10 Top Corner Panel 31500410 31500610 1
11 Firebox Support 31500011 31500011 1
12 Base Panel Support 31500012 31500012 1
13 Top Panel Support 31500013 31500013 1
14 Corner Mantel Support 31500014 31500014 1
15 Hardware Kit 31500015 31500015 1
4
Step One
-Join left side panel (2) with left front panel (4) by securing 6 short allen screws through 3
L-brackets.
-Repeat with right side panel (3) and right front panel (5).
Step Two
-Set base panel (1) on a at surface as shown.
-Attach 6 L-brackets to base panel (1) by securing 6 short allen screws.
A
2
3
4
5
A
A
B
1
A
B
5
Step Three
-Join panel (2) & (4), (3) & (5) with base panel (1) by securing 6 short allen screws through 6
L-brackets.
Step Four
-Attach 4 L-brackets to center panel (7) by securing 4 short allen screws.
1
2
3
4
5
A
B
7
A
B
6
Step Five
-Attach center panel (7) to side panel (2) & (3) by securing 4 short allen screws through 4
L-brackets.
-Attach center panel (7) on front panel (4) & (5) by securing 4 long allen screws through 4 washers
and 2 MDF boards.
Step Six
-Attach lower rebox trim (6) to front panel (4) & (5) by securing 2 long allen screws through 2
washers.
7
2
3
4
5
A
B
C
D
6
C
D
4
5
F
7
Step Seven
-Attach rebox support (11) to base panel (1) by securing 2 long allen screws.
-For wall unit, continue with Step Eight.
-For corner unit, continue with Step Nine to Eleven .
Step Eight
Proceed to step twelve if you plan to use the unit as a wall unit.
-Locate top front panel (8) to above nished parts .
-Join center panel (7) and side panel (2) & (3) by securing 5 long allen screws through 5 washers.
-Check and tighten all the screws with the allen wrench provided.
11
1
C
8
7
2
3
C
D
8
Step Nine
-Join base panel support (12) with base panel (1) by securing 2 long allen screws.
-Attach corner mantel support (14) to base panel support (12) by securing 1 long allen screw
through 1 washer.
Step Ten
-Join top front panel (8), top center panel (9) with top corner panel (10) by securing 6 long allen
screws through 6 washers.
-Attach top panel support (13) by securing 4 long allen screws.
1 12
14
C
C
D
8
9
10
13
C
C
D
9
Step Eleven
-Locate top panel to above nished parts.
-Join center panel (7) and side panel (2) & (3) by securing 5 long allen screws through 5 washers.
-Join corner mantel support (14) by securing 1 long allen screw through 1 washer.
-Check and tighten all the screws with the allen wrench provided.
2 3
C D
7
14
C
D
For next step reference the instruction manual included with your rebox.
If you do not have an instruction manual included with your rebox do not attempt to
assemble or operate. Immediately call our customer service department
at 1-800-654-1704 for a replacement manual
WARNING: Do not operate your rebox without reading all instructions and warnings
prior to use.
Step Twelve
10
Ninety-Day Warranty: Jensen Metal Products Inc. D/B/A Real Flame® warrants Real Flame vent-less
fireplaces and accessories to be free from defects in parts and workmanship under normal use and
service for a period of 90 days from date of shipment. In the event of such defect in parts or
workmanship, Jensen will, at its option, replace the defective product or refund the purchase price to
the extent of the defective product’s replacement cost. The foregoing is the exclusive remedy and
Real Flame disclaims all other warranties, including any implied warranty of merchantability or fitness
for a particular purpose. In addition, Real Flame will not be responsible for consequential damages in
excess of the purchase price of the product on which such liability is based.
Replacement Parts: Replacement parts are available for most units. Occasionally, parts may arrive
damaged due to mishandling during shipping. If you are in need of a replacement part, please
contact our customer service department with the fireplace model number and part number needed.
We will ship out a replacement part due to shipping damage at no charge.
Returns: Please inspect all items immediately after receiving. We hope you will be completely happy
with your purchase. If you find within 15 days of receipt of your product that you do not wish to keep
it, you may return it unused by following our return procedure. Shipping charges are not refundable
unless the return is a result of our error. Return freight charges are the responsibility of the buyer.
Items must be returned in their original packaging.
All returns must be authorized. Product that has been used may not be returned. A 15% restocking
fee will be assessed on returned merchandise to compensate for repackaging, warehousing and
administrative labor. The return procedure is listed below. For specific questions relating to returns or
warranty, please contact Customer Service department toll-free at 1-800-654-1704 or at
custserv@realflame.com.
Step 1: Contact Customer Service department by phone or e-mail to receive your Return
Merchandise Authorization number (RMA#). The RMA# is necessary for all returns. A reason code
must be indicated on the return form included with your packing slip.
Step 2: Note your RMA# on the packing slip and repack the item in the original packaging. Be sure to
include your packing slip with the returned product.
Step 3: Include your RMA# on the outside of the box and ship the package back to us via common
carrier. Please provide us with the tracking number for your shipment.
Step 4: We will contact you when the package has been received and inspected. Provided a
satisfactory return, we will credit your account for the returned merchandise less the applicable
restocking charges.
Customer Service:
1-800-654-1704 or
custserv@realflame.com
Warranty & Return Policies
Real Flame®
7800 Northwestern Ave.
Racine, WI 53403
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Real Flame 3150-LO User guide

Category
Fireplaces
Type
User guide

Real Flame 3150-LO is a gel fireplace and accessory designed for indoor use, eliminating the need for ventilation. It features a sturdy construction with various components, including panels, supports, and trim, that can be assembled to create a stylish and functional fireplace. The included hardware kit facilitates the assembly process, and the provided instructions guide you through each step to ensure a proper installation.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages