BEGLEC LED PIPE RGB 230V Owner's manual

Brand: BEGLEC

Model: LED PIPE RGB 230V

Category: Floodlights

Type: Owner's manual

This manual is also suitable for

Version: 1.0

WWW.BEGLEC.COM

Reproduction or publication of the content in any manner, without express permission of the publisher, is prohibited.

LED PIPE RGB

230V

Operation Manual

Mode d'emploi

Gebruiksaanwijzing

Bedienungsanleitung

Manual de instrucciones

EN - DISPOSAL OF THE DEVICE

Dispose of the unit and used batteries in an environment friendly manner

according to your country regulations.

FR - DÉCLASSER L’APPAREIL

Débarrassez-vous de l’appareil et des piles usagées de manière écologique

Conformément aux dispositions légales de votre pays.

NL - VERWIJDEREN VAN HET APPARAAT

Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke

manier conform de in uw land geldende voorschriften.

DU - ENTSORGUNG DES GERÄTS

Entsorgen Sie das Gerät und die Batterien auf umweltfreundliche Art und

Weise gemäß den Vorschriften Ihres Landes.

ES - DESHACERSE DEL APARATO

Reciclar el aparato y pilas usadas de forma ecologica conforme a las

disposiciones legales de su pais.

PT - COMO DESFAZER-SE DA UNIDADE

Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em

conformidade com as normas vigentes no seu país.

ENGLISH OPERATION MANUAL

JB SYSTEMS

1/34 LED PIPE RGB 230V

Thank you for buying this JB Systems

product. To take full advantage of all possibilities and for your own

safety, please read theseoperating instructions very carefully before you start using this unit.

A complete JBSystems

LED PIPE 230V system contains thefollowing components:

 1 or more LEDPIPE tubes (can work standalone or can be connected to the LED PIPE controller)

 1 optional LED PIPE controller (controls theconnected led tubes)

 Optionalsignal extension cables: 1m, 5m or 10m.

FEATURES

This unit is radio-interference suppressed. This product meets the requirements of the current European and

national guidelines. Conformity has been established and therelevant statements and documents havebeen

deposited by the manufacturer.

 This device has been designed toproduce decorative effect lighting and isused in light show systems.

 Each LED PIPE uses144 high efficiencyleds. (Red=48,Green=48, Blue=48)

 Each LED PIPE is splitup in 16 sections formaximum flexibility whileprogramming patterns!

 A chain of LED PIPE unitscan be used in 3 ways:



Standalone without controller:

many wonderful build-in patterns, alsomusic activated!



Standalone with controller:

the optional LED PIPE controller can control up to 1000 tubes with

additional flexibility.



DMX control viacontroller:

uses3 DMXchannels

 4 program run modes:auto mode(adjustable speed), Sound mode, dB mode(VU-meter), hold mode.

 Lightweight polymerenclosure with high qualityfrost lens for indoor use.

 Specially shaped base makes it possible to hide all connection cables nicely behind the units!

 Internal power supply for easydaisy chaining ofup to200 units on only one 230V/16Awall socket!

 Can beeasily fixed to walls and ceilings with the supplied wall brackets.

 Suitable for indoor use only.

 Extended lifespan: 50.000 – 100.000hours

 Lowpower consumption: only 18W pertube!

 Optional signal extension cables: 1m, 5m or 10m available.

 Perfect for use in: retail stores, commercial displays, architectural lighting, indoor decoration, clubs, pubs,

mobile DJs, trussing, …

BEFORE USE

 Before you start using this unit, please check if there’s no transportation damage. Should there be any, do

not usethe device and consult your dealer first.



Important:

This device left our factory in perfect condition and well packaged. It is absolutely necessary

for the user to strictly follow the safety instructions and warnings in this user manual. Any damage caused

by mishandling is not subject to warranty. The dealer will not accept responsibility for any resulting defects

orproblems caused by disregarding this user manual.

 Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to add this user

manual.

Check thecontents:

Check that the carton contains the following items:

 Operatinginstructions

 LED PIPERGB unit

SAFETY INSTRUCTIONS:

CAUTION: To reduce the risk of electric shock, do not remove the top cover.

No user-serviceable parts inside. Refer servicing to qualified service

personnel only.

CAUTION

ENGLISH OPERATION MANUAL

JB SYSTEMS

2/34 LED PIPE RGB 230V

The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use

or the presence of un-insulated “dangerous voltage” within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence of

important operation and maintenance (servicing) instructions in the literature accompanying this

appliance.

This symbol means: indoor use only.

Thissymbol means:Read instructions.

 To protect theenvironment, please try to recyclethe packing material as much as possible.

 To prevent fire or shock hazard, do notexpose this appliance to rain ormoisture.

 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance or mayeven cause damages.

 This unit is for indoor useonly.

 Don’t placemetal objects or spill liquid inside the unit. Electric shock or malfunction may result. If a foreign

object enters the unit, immediately disconnect the mains power.

 Prevent use in dusty environments and cleanthe unit regularly.

 Keep the unit away from children.

 Inexperienced persons should not operatethis device.

 Maximum save ambient temperature is 40°C. Don’t use this unitat higher ambient temperatures.

 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

and servicing.

 Always unplug the unit when it is not used for a longer time or before servicing.

 The electrical installation should be carried out by qualified personal only, according to the regulations for

electrical and mechanical safetyin your country.

 Check that the available voltage is not higher than the one stated on the rear panel of the unit.

 The power cord should always be in perfect condition. Switch theunit immediately off when the power cord

is squashed or damaged. It must be replaced by the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

 Never let the power-cord come into contact with other cables!

 This fixture must be earthed to in order comply withsafety regulations.

 Don’t connect the unit to any dimmer pack.

 In order to prevent electric shock, do not open the cover. There are no user serviceable parts inside.



Never

repair a fuse or bypass the fuse holder.

Always

replace a damaged fuse with a fuse of the same

type and electrical specifications!

 In the event ofserious operating problems,stop using the fixture and contact your dealer immediately.

 Thehousing and the lenses must be replaced if theyare visibly damaged.

 Please use the original packing when thedevice is to be transported.

 Due to safety reasons it is prohibited to make unauthorized modifications tothe unit.

Important:

Don’t usethe effect in the presenceof persons suffering from epilepsy.

DESCRIPTION:

ENGLISH OPERATION MANUAL

JB SYSTEMS

3/34 LED PIPE RGB 230V

1. LED PIPE SIGNAL INPUT: low voltage signal input to be connected with the signal output of the

previous tube or with the signal output cable from the controller. Extra 1m, 5m or 10m signal cable

extensions are optionally available.

2. LED PIPE SIGNAL OUTPUT: low voltage signal output to be connected with the signal input of the next

tube. Extra 1m, 5m or 10m signal cable extensions are optionally available.

3. POWER INPUT CABLE: To be connected with power output cable of the previous tube or directly with

themains.

4. POWER OUTPUTCABLE: To be connected with the power input cable of the next tube.

5. LED PIPE HOLDERS: Needed to fix the tubes easily against a surface. The shape of the enclosure and

the holders makes itpossible to hide your cables perfectly behind yourconstruction.

6. DIPSWITCHES: used to setup the different usermodes of the tube.

7. PLASTIC COVER: The milky white plastic cover is used to mix the 3 primary colors. If you like you can

install the LED PIPE tubes behind a big milky white opaque surface to create an “ever color changing

wall”. In this case you can try to remove the plastic cover from the LED PIPE to obtain morelight output.

This can be easily done by removing the 2 small screws on one side of the plastic cover. Once the end

cap removed you can easily slide the plastic cover out of the base.

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper installation can

result in serious injuries and/or damage to property. Overhead rigging requires extensive experience!

Working load limits should be respected, certified installation materials should be used, the installed

device should be inspected regularly forsafety.

 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging

andservicing.

 Before rigging make sure that the installation area can hold a minimum point load of 10times the device’s

weight.

 The device should be well fixed; a free-swinging mounting is dangerous and maynot be considered!

 The operator has to make sure that the safety-relatingand machine-technicalinstallations are approved by

an expert before using them for the first time. The installations should be inspected every year by a skilled

person to be sure that safety is still optimal.

ELECTRICAL INSTALLATION + SETUP

Important: The electrical installation

should be carried out by qualified

personal only, according to the regulations

for electrical and mechanical safety in your

country.

You can install the tubes in 2 ways: with or without

controller.

INSTALLATION WITH CONTROLLER:

Fix all the tubes properly to wall or ceiling.

Connect the signal cables of all tubes together.

Make sure to fasten the plastic ring well. (see

n°3 on the picture)

Connect the power cables of all tubes together

and connect the first unit to the mains. (see n°2

and 3 on the picture) PS: to connect the first unit

to the mains, you need an optional mains cable

with IEC-socket on one end.

Connect the signal input cable of the first tube to

the signal output connector of the LED PIPE

controller. Eventually use the optional extension

cables. (Seen°1 on the picture)

Switch the controller on and follow the setup of

the controller like suggested in the manual of

the LED PIPE controller

ENGLISH OPERATION MANUAL

JB SYSTEMS

4/34 LED PIPE RGB 230V

Done!

Remarks:

You can daisy chain up to 1000 tubes on 1 controller. The DIP-switch settings on the individual LED PIPES

have no effect in asetup with controller. For detailed explanations on how the controller works and how you

can control yoursetup by DMX, please referto the usermanual forthe LED PIPEcontroller.

INSTALLATION WITHOUT CONTROLLER:

The installation without controller is almost identical so please refer to points 1 to 3 above.

When no controller is connected, the first unit in the chain will act as the master: only use the DIP-switches

on this master unit. The DIP-switch settings on the other (slave) LED PIPES have no effect.

 PATTERN REPETITION

Dipswitch1+2: used tochoose after howmany tubesthe build-in patterns are repeated.

Patterns are repeated every 32 tubes.

Patterns are repeated every 16 tubes.

Patterns are repeated every 8 tubes.

Patterns are repeated every 4 tubes.

 PATTERN PLAYBACK SPEED

Dipswitch 5+6: used toset the playback speed of thepatterns in auto mode

Playbackspeed is very slow.

Playbackspeed is slow.

Playback speed is fast.

Playback speed is very fast.

 AUTO MODE (DIP3 = OFF - DIP4 = OFF)

DIP10 = switch ON for pattern inversion

Random mode(7 chases)

Auto fade

One color in one way

One color in two way

Multicolor in oneway

Multicolor in twoway

Multicolor strobe

Strobe in white light

ENGLISH OPERATION MANUAL

JB SYSTEMS

5/34 LED PIPE RGB 230V

 SOUND MODE (DIP3 = ON - DIP4 = OFF)

DIP10 = switch ON for pattern inversion

Random mode(7 chases)

Colorchange bysound in two waychase

One color in one way

One color in two way

Multicolor in oneway

Multicolor in twoway

Colorchange bysound

Colorchange instrobe

 dB MODE (DIP3 = OFF - DIP4 = ON)

DIP10 = switch ON for pattern inversion

Random mode(7 chases)

Multicolor chase light with red base color

Multicolor chaselight with green base color

Multicolor chase light with blue base color

Multicolor chaselight with black base color

VU-meter with green/yellow/red color

Multicolor VU-meter 1

Multicolor VU-meter 2

 HOLD MODE (DIP3 = ON - DIP4 = ON)

DIP10 = not used

All tubes white

All tubes red

All tubes green

All tubesyellow

All tubes blue

All tubes purple

All tubes cyan

All tubes white

ENGLISH OPERATION MANUAL

JB SYSTEMS

6/34 LED PIPE RGB 230V

OPERATING INSTRUCTIONS

 Once connected to the mains the devices startrunning.

 You can also connect the units to the LED PIPE controller for extra functions and DMX-control. When

used with the controller, pleasealso check its user manual.

 Do not switch the unit on and off in short time intervals as this reduces the lamp life.

 Always unplug the unit when it is not used fora longer time or before replacing the bulb or start servicing.

 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.

 Important: Don’t usethe effect in thepresence of persons suffering from epilepsy.

MAINTENANCE

 Make sure the area below the installation is free fromunwantedpersons during servicing.

During inspection the following points should be checked:

 All screws used for installing the device and any of its parts should be tightly fastened and may not be

corroded.

 Housings, fixations and installations spots (ceiling, truss, suspensions) should be totally free from any

deformation.

 When an opticallens is visibly damaged dueto cracks or deep scratches, it must be replaced.

 The mains cables must be in impeccable condition and should be replaced immediately when even a

small problem is detected.

 The cleaning of external optical lenses and/or mirrors must be carried out periodically to optimize light

output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or

particularly dirtysurroundings can cause greater accumulation of dirt on the unit’soptics.

 Clean with a soft cloth using normalglass cleaning products.

 Always dry the parts carefully.

 Clean the external opticsat least once every 30 days.

SPECIFICATIONS

Mains Input: AC230V, 50Hz

Power consumption: 18Watt

Number ofLEDs: 144 pcs (48 red, 48 green,48 blue)

DifferentLED sections: 16

Beam Angle: 120°

Life span of LEDs: 50000~100000hours

Soundcontrol: Internal microphone

Size: 1000 x 62 x100mm

Weight: 1.6kg

Every information is subject to change without prior notice

You can download the latest version of thisuser manual on our website: www.beglec.com

Page is loading ...

BEGLEC LED PIPE RGB 230V Owner's manual

Brand: BEGLEC

Model: LED PIPE RGB 230V

Category: Floodlights

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

français: BEGLEC LED PIPE RGB 230V Le manuel du propriétaire
español: BEGLEC LED PIPE RGB 230V El manual del propietario
Deutsch: BEGLEC LED PIPE RGB 230V Bedienungsanleitung
Nederlands: BEGLEC LED PIPE RGB 230V de handleiding

BEGLEC LED PIPE RGB 230V Owner's manual

This manual is also suitable for

BEGLEC LED PIPE RGB 230V Owner's manual

in other languages

Related papers

Other documents