Sytech SY1033PNEGRO Owner's manual
- Category
- Alarm clocks
- Type
- Owner's manual
Page is loading ...
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES
CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT
FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
The Caution Marking is located at the bottom enclosure of the apparatus.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
1. Read these instructions. All the safety and operating instructions should be read before the
appliance is operated.
2. Retain instructions. The safety and operating instructions should be retained for future
reference.
3. Heed all warnings. All warnings on the appliance and in the operating instructions should be
adhered to.
4. Follow all instructions. All operating instructions should be followed.
5. Water and moisture. The appliance should not be used near water, for example,
near a
bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.
6. Ventilation. The appliance should be situated so that its location or position does not
interfere with its proper ventilation. Do not place it on the bed, sofa, rug or similar surfaces
that may block the ventilation openings, in a built-in installation, such as a bookcase or
cabinet that may impede the flow of air through the ventilation openings.
7. Heat. The appliance should be sit
uated away from heat sources such as radiators, stoves, or
other appliances (including amplifiers) that produce heat.
8. Power source. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For products intended to operate from
battery power, or other sources, refer to the operating instruction.
9. Cleaning. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners
or aerosol cleaners. Clean only with dry cloth.
10. Location. Do not place this product on an unstable cart, stand, tripod,
bracket, or table. The product may fall, causing serious injury to a child
or adult and serious d
amage to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should follow the
manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer. A product and cart combination should be moved with
care-quick stops, excessive force and uneven surfaces may cause the product and cart
combination to overturn.
11. Protection. Protect th
e power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the appliance.
12. Accessories. Only use attachments/accessories specified by the manufacturer.
13. Disconnect. Unplug the appliance during lightning storms or when unused for a long periods
of time.
14. Service department. Refer all servicing to Sytech technical department. Servicing is
required when the appliance has been damaged in any way, such as power
-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
15. Water. This appliance shall not be exposed to dripping or splashing water and that no object
filled with liquids such as vases shall be placed on the apparatus.
16. Wall outlet. Do not overload wall outlet. Use only power source as indicated.
17. Parts. Use replacement part as specified b
y the manufacturer.
18. Mounting. The product may be mounted to a wall only if recommended by the manufacturer.
19. Upon completion of any service or repairs to this product, ask the service technician to
perform safety checks.
20. Object and Liquid Entry. Never push objects of any kind into this product through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
21. Damage Requiring Service. Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the operating instructions. Adjust
only those controls that are covered by the operating instructions
as an improper
adjustment of other controls may result in damage and will often require extensive work
by a qualified technician to restore the product to its normal operation.
e) If the product has been dropped or damaged in any way
f) The appliance does not appear to operate normally.
LOCATION OF CONTROL
DISPLAY
SCAN -
MODE
AL2
AL1
VOL-
VOL+
SLEEP
SET MEMO
SNOOZE/LIGHT
PROJECTOR
E-1
SCAN +
FEATURES
LCD display with backlight
Clock/Date/Weekday display
12/24 Hours display se ng
Dual Alarm
Wake up by Radio/Buzzer
SNOOZE
Sleep Fun on (Radio mode)
PLL FM Radio
10 Radio Preset Sta
Volume Control. Total 16 levels (defaulted at level 6 at the beginning)
Bu on Cell ba ery backup
FUNCTION KEY
AL1: Press for checking Alarm1 status & Alarm1 se ng
AL2: Press for checking Alarm2 status & Alarm2 se ng
MODE: For Changing mode, Clock(standby) > Radio
SCAN-: (Radio) Press once Radio frequency down,
Press & hold for radio sta
on searching
SCAN+: (Radio) Press once for Radio frequency up,
Press & hold for radio sta
on searching
SET: (Clock) For clock se ng
MEMO: (Radio) For se ng the preset radio sta on
SLEEP Press for sleep mer setup (90>60>30>15>0)
VOL +/- Volume level UP/DOWN
SNOOZE/LIGHT: - Snooze when in alarm mode
(Each press for repea
alarm every 9 minutes, last for 1 hour)
- Light
on when in normal situa
(Press once for LCD backlight ON for 60 seconds)
(Press & hold for LCD backlight always ON, then press & hold again for return to
normal situa
E-2
CLOCK OPERATION
Time Se ng
Press MODE un l you enter the Clock Display Mode (or it will be in Clock Display Mode when you
first connect with Electricity)
Press & hold the SET bu on to enter Time Se ng Mode
Alarm Time Se ng
In Clock Display Mode
Press AL1/AL2 bu on to enter the Alarm Time Se ng Mode.
Press AL1/AL2 once again to select the alarm sound source.
The sequence: Off > Radio > Buzzer
Press the SET bu on to enter the Alarm Time
Minutes > Hour > Preset radio sta
on
number
> Volume
(Radio preset sta
on must be set before using this Otherwise, alarm
will only wake up to
the default sta
on at FM 87.5MHz)
Minutes > Hour
The Seng sequence for waking up by buzzer are as follow:
RADIO OPERATION
Press MODE bu on to enter Radio Mode
default at FM87.5 when first use
Last radio frequency memory
Repeat the above procedures to store more radio sta ons (maximum 10 preset radio sta ons).
Listening to the radio by preset sta
on
E-3
Press SCAN-/SCAN+ to set the desired me. Press the SET buon to confirm and move on to the
next seng
Clock Seng sequence: Minutes>Hour>12/24 hr>Year>Month>Day
The Seng sequence for waking up by radio are as follow:
Press the MODE buon at any me to return to the Clock Display Mode.
The alarm lasts for 1 hour.
To stop the Alarm, simply press the AL1/ AL2 buon.
The alarm restarts every 9 minutes aer each press of SNOOZE.
To search manually for a radio staon, simply press the SCAN-/SCAN+.
For an automac scan search, press & hold the SCAN-/SCAN+ buon. The unit will automacally
search the next radio staon.
Once the radio staon been selected, press & hold the MEMO buon to enter the Preset Radio
Staon mode. Then, press the SCAN-/SCAN+ to select the desired preset staon number. Press
the MEMO buon once more to confirm the selecon. Now your favorite stao is stored in the
selected preset number.
In Radio Mode, press the MEMO buon to select the desired preset radio staon. Press the
MEMO buon once more to advance to the next preset staon.
SNOOZE/LIGHT FUNCTION
During the wakeup press the SNOOZE/LIGHT bu on once to temporarily turn off the alarm.
A
er approximately 9 minutes the alarm will sound again. The cycle will repeat when the SNOOZE /
LIGHT bu
on is pressed again. Alarm max last for 1 hour
Note:
When pressing the SNOOZE / LIGHT bu on, the panel backlight will turn on, and will turn off
automa
cally er 1 minute.
SLEEP FUNCTION
The sleep is used for automa switch-off of the Radio
SPECIFICATIONS
Radio Frequency : FM – 87.5 – 108MHz
Antenna : External Antenna Wire
Output : 500mW Max.
Speaker : 50mm, 8ohm x 1
Power Required : Input 230v 50Hz
Clock backup – DC3V, 1 x CR2032 ba
ery (ba ery included)
While every effort has been made to ensure all informa
contained in this manual is correct, design
and specifica
re subject to change without no e.
E-4
PROJECTOR
Press and hold the SNOOZE/LIGHT buon for the backlight to always be ON. Press and hold once
more for the backlight to return to its normal status.
If you wish to hear the radio for a certain me before going to sleep, press the “MODE” buon to
switch to the radio mode. Search the desired channel by pressing the SCAN+ or SCAN- buon. At
this moment, press the SLEEP buon and the display will show 90 min. Press the SLEEP buon unl
you have set the desired me for the unit to off. The opons for the SLEEP funcon are as follow:
90, 60, 30, 15, Off. Once the selected me has elapsed, the radio will automacally shut down.
BRIGHT OR DIM SET
The negave display of the SY-1033 is perfect for the night as it does not reflect the numbers.
To increase the luminosity of the display, press the LIGHT buon for the display to brighten up.
Aer approximately 1 minute, the display will return to the original dim light.
TIME MEMORY SET
The SY-1033 includes a baery backup feature in case of power failure. Plug in the radio clock to
the mains output. Adjust al the parameters such as the year, month, date and me. Open the baery
compartment located at the boom of the unit and insert 1 x CR2032 baery in the correct posion
(included). In the case of any cut off power, the SY-1033 will retain the actual me and date unl the
main power comes back.
DECLARATION OF CONFORMITY
Manufacturer Name: Satyatrade S. L .
Address: Pol. Ind. La Raya. C/ Guadalquivir, 2
Camarma de Esteruelas, 28816 Madrid
Tel: 902 430 967
Fax: 9 1 8864285
NIF: B83254763
Manufacturing country: China
Sytech ® SY -1033 complies with the following direcves:
CE standard:EMC Direcve 2004/108/EC
EN 55013:2001+A1 +A2
EN 61000 - 6 - 3 : 2007
EN 61000 - 3 - 3 :2008
EN 55020 :2007
EN 6100 -6 - 1 :2007
ERP St
andards : Direcve 2009/125/EC
EN 62301:2005+1275/2008/EC
Low voltage: Direcve 2006/95/EC
EN 60065:2002+A1:2006+A11:2008
ROHS standard:2002/95/EC Restricon of Hazardous Substance
Signed: Ajeet Nebhwani Utamchandani
Sole Administrator
RADIO DESPERTADOR
modelo:SY-1033
MANUAL DE INSTRUCCIONES
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
Sytech SY1033PNEGRO Owner's manual
- Category
- Alarm clocks
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
