Sytech SY1033PNEGRO Owner's manual

Page is loading ...

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN

EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES

CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT

FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

The Caution Marking is located at the bottom enclosure of the apparatus.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

1. Read these instructions. All the safety and operating instructions should be read before the

appliance is operated.

2. Retain instructions. The safety and operating instructions should be retained for future

reference.

3. Heed all warnings. All warnings on the appliance and in the operating instructions should be

adhered to.

4. Follow all instructions. All operating instructions should be followed.

5. Water and moisture. The appliance should not be used near water, for example,

near a

bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.

6. Ventilation. The appliance should be situated so that its location or position does not

interfere with its proper ventilation. Do not place it on the bed, sofa, rug or similar surfaces

that may block the ventilation openings, in a built-in installation, such as a bookcase or

cabinet that may impede the flow of air through the ventilation openings.

7. Heat. The appliance should be sit

uated away from heat sources such as radiators, stoves, or

other appliances (including amplifiers) that produce heat.

8. Power source. This product should be operated only from the type of power source

indicated on the marking label. If you are not sure of the type of power supply to your home,

consult your product dealer or local power company. For products intended to operate from

battery power, or other sources, refer to the operating instruction.

9. Cleaning. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners

or aerosol cleaners. Clean only with dry cloth.

10. Location. Do not place this product on an unstable cart, stand, tripod,

bracket, or table. The product may fall, causing serious injury to a child

or adult and serious d

amage to the product. Use only with a cart, stand,

tripod, bracket, or table recommended by the manufacturer, or sold

with the product. Any mounting of the product should follow the

manufacturer’s instructions, and should use a mounting accessory

recommended by the manufacturer. A product and cart combination should be moved with

care-quick stops, excessive force and uneven surfaces may cause the product and cart

combination to overturn.

11. Protection. Protect th

e power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the appliance.

12. Accessories. Only use attachments/accessories specified by the manufacturer.

13. Disconnect. Unplug the appliance during lightning storms or when unused for a long periods

of time.

14. Service department. Refer all servicing to Sytech technical department. Servicing is

required when the appliance has been damaged in any way, such as power

-supply cord or

plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has been

dropped.

15. Water. This appliance shall not be exposed to dripping or splashing water and that no object

filled with liquids such as vases shall be placed on the apparatus.

16. Wall outlet. Do not overload wall outlet. Use only power source as indicated.

17. Parts. Use replacement part as specified b

y the manufacturer.

18. Mounting. The product may be mounted to a wall only if recommended by the manufacturer.

19. Upon completion of any service or repairs to this product, ask the service technician to

perform safety checks.

20. Object and Liquid Entry. Never push objects of any kind into this product through openings

as they may touch dangerous voltage points or short-out parts that could result in a fire or

electric shock. Never spill liquid of any kind on the product.

21. Damage Requiring Service. Unplug this product from the wall outlet and refer servicing to

qualified service personnel under the following conditions:

a) When the power-supply cord or plug is damaged,

b) If liquid has been spilled, or objects have fallen into the product,

c) If the product has been exposed to rain or water,

d) If the product does not operate normally by following the operating instructions. Adjust

only those controls that are covered by the operating instructions

as an improper

adjustment of other controls may result in damage and will often require extensive work

by a qualified technician to restore the product to its normal operation.

e) If the product has been dropped or damaged in any way

f) The appliance does not appear to operate normally.

LOCATION OF CONTROL

DISPLAY

SCAN -

MODE

AL2

AL1

VOL-

VOL+

SLEEP

SET MEMO

SNOOZE/LIGHT

PROJECTOR

E-1

SCAN +

FEATURES

LCD display with backlight

Clock/Date/Weekday display

12/24 Hours display se ng

Dual Alarm

Wake up by Radio/Buzzer

SNOOZE

Sleep Fun on (Radio mode)

PLL FM Radio

10 Radio Preset Sta

Volume Control. Total 16 levels (defaulted at level 6 at the beginning)

Bu on Cell ba ery backup

FUNCTION KEY

AL1: Press for checking Alarm1 status & Alarm1 se ng

AL2: Press for checking Alarm2 status & Alarm2 se ng

MODE: For Changing mode, Clock(standby) > Radio

SCAN-: (Radio) Press once Radio frequency down,

Press & hold for radio sta

on searching

SCAN+: (Radio) Press once for Radio frequency up,

Press & hold for radio sta

on searching

SET: (Clock) For clock se ng

MEMO: (Radio) For se ng the preset radio sta on

SLEEP Press for sleep mer setup (90>60>30>15>0)

VOL +/- Volume level UP/DOWN

SNOOZE/LIGHT: - Snooze when in alarm mode

(Each press for repea

alarm every 9 minutes, last for 1 hour)

- Light

on when in normal situa

(Press once for LCD backlight ON for 60 seconds)

(Press & hold for LCD backlight always ON, then press & hold again for return to

normal situa

E-2

CLOCK OPERATION

Time Se ng

Press MODE un l you enter the Clock Display Mode (or it will be in Clock Display Mode when you

ﬁrst connect with Electricity)

Press & hold the SET bu on to enter Time Se ng Mode

Alarm Time Se ng

In Clock Display Mode

Press AL1/AL2 bu on to enter the Alarm Time Se ng Mode.

Press AL1/AL2 once again to select the alarm sound source.

The sequence: Oﬀ > Radio > Buzzer

Press the SET bu on to enter the Alarm Time

Minutes > Hour > Preset radio sta

on

number

> Volume

(Radio preset sta

on must be set before using this Otherwise, alarm

will only wake up to

the default sta

on at FM 87.5MHz)

Minutes > Hour

The Seng sequence for waking up by buzzer are as follow:

RADIO OPERATION

Press MODE bu on to enter Radio Mode

default at FM87.5 when ﬁrst use

Last radio frequency memory

Repeat the above procedures to store more radio sta ons (maximum 10 preset radio sta ons).

Listening to the radio by preset sta

on

E-3

Press SCAN-/SCAN+ to set the desired me. Press the SET buon to conﬁrm and move on to the

next seng

Clock Seng sequence: Minutes>Hour>12/24 hr>Year>Month>Day

The Seng sequence for waking up by radio are as follow:

Press the MODE buon at any me to return to the Clock Display Mode.

The alarm lasts for 1 hour.

To stop the Alarm, simply press the AL1/ AL2 buon.

The alarm restarts every 9 minutes aer each press of SNOOZE.

To search manually for a radio staon, simply press the SCAN-/SCAN+.

For an automac scan search, press & hold the SCAN-/SCAN+ buon. The unit will automacally

search the next radio staon.

Once the radio staon been selected, press & hold the MEMO buon to enter the Preset Radio

Staon mode. Then, press the SCAN-/SCAN+ to select the desired preset staon number. Press

the MEMO buon once more to conﬁrm the selecon. Now your favorite stao is stored in the

selected preset number.

In Radio Mode, press the MEMO buon to select the desired preset radio staon. Press the

MEMO buon once more to advance to the next preset staon.

SNOOZE/LIGHT FUNCTION

During the wakeup press the SNOOZE/LIGHT bu on once to temporarily turn oﬀ the alarm.

A

er approximately 9 minutes the alarm will sound again. The cycle will repeat when the SNOOZE /

LIGHT bu

on is pressed again. Alarm max last for 1 hour

Note:

When pressing the SNOOZE / LIGHT bu on, the panel backlight will turn on, and will turn oﬀ

automa

cally er 1 minute.

SLEEP FUNCTION

The sleep is used for automa switch-oﬀ of the Radio

SPECIFICATIONS

Radio Frequency : FM – 87.5 – 108MHz

Antenna : External Antenna Wire

Output : 500mW Max.

Speaker : 50mm, 8ohm x 1

Power Required : Input 230v 50Hz

Clock backup – DC3V, 1 x CR2032 ba

ery (ba ery included)

While every eﬀort has been made to ensure all informa

contained in this manual is correct, design

and speciﬁca

re subject to change without no e.

E-4

PROJECTOR

Press and hold the SNOOZE/LIGHT buon for the backlight to always be ON. Press and hold once

more for the backlight to return to its normal status.

If you wish to hear the radio for a certain me before going to sleep, press the “MODE” buon to

switch to the radio mode. Search the desired channel by pressing the SCAN+ or SCAN- buon. At

this moment, press the SLEEP buon and the display will show 90 min. Press the SLEEP buon unl

you have set the desired me for the unit to oﬀ. The opons for the SLEEP funcon are as follow:

90, 60, 30, 15, Oﬀ. Once the selected me has elapsed, the radio will automacally shut down.

BRIGHT OR DIM SET

The negave display of the SY-1033 is perfect for the night as it does not reﬂect the numbers.

To increase the luminosity of the display, press the LIGHT buon for the display to brighten up.

Aer approximately 1 minute, the display will return to the original dim light.

TIME MEMORY SET

The SY-1033 includes a baery backup feature in case of power failure. Plug in the radio clock to

the mains output. Adjust al the parameters such as the year, month, date and me. Open the baery

compartment located at the boom of the unit and insert 1 x CR2032 baery in the correct posion

(included). In the case of any cut oﬀ power, the SY-1033 will retain the actual me and date unl the

main power comes back.

DECLARATION OF CONFORMITY

Manufacturer Name: Satyatrade S. L .

Address: Pol. Ind. La Raya. C/ Guadalquivir, 2

Camarma de Esteruelas, 28816 Madrid

Tel: 902 430 967

Fax: 9 1 8864285

NIF: B83254763

Manufacturing country: China

Sytech ® SY -1033 complies with the following direcves:

CE standard:EMC Direcve 2004/108/EC

EN 55013:2001+A1 +A2

EN 61000 - 6 - 3 : 2007

EN 61000 - 3 - 3 :2008

EN 55020 :2007

EN 6100 -6 - 1 :2007

ERP St

andards : Direcve 2009/125/EC

EN 62301:2005+1275/2008/EC

Low voltage: Direcve 2006/95/EC

EN 60065:2002+A1:2006+A11:2008

ROHS standard:2002/95/EC Restricon of Hazardous Substance

Signed: Ajeet Nebhwani Utamchandani

Sole Administrator

RADIO DESPERTADOR

modelo:SY-1033

MANUAL DE INSTRUCCIONES

Page is loading ...

Sytech SY1033PNEGRO Owner's manual

Sytech SY1033PNEGRO Owner's manual

in other languages

Related papers

Other documents