Miller MB060031U Owner's manual

Processes

Description

MIG (GMAW) Welding

MIG (GMAW-P) Welding

Flux Cored (FCAW) Welding

(Gas- And Self-Shielded)

Wire Feeder

Aluminum Push/Pull Capable

OM-243 346C

2011−01

File: MIG (GMAW)

Visit our website at

www.MillerWelds.com

S-74 MPa Plus

Miller Electric manufactures a full line

of welders and welding related equipment.

For information on other quality Miller

products, contact your local Miller distributor to receive the latest full

line catalog or individual specification sheets. To locate your nearest

distributor or service agency call 1-800-4-A-Miller, or visit us at

www.MillerWelds.com on the web.

Thank you and congratulations on choosing Miller. Now you can get

the job done and get it done right. We know you don’t have time to do

it any other way.

That’s why when Niels Miller first started building arc welders in 1929,

he made sure his products offered long-lasting value and superior

quality. Like you, his customers couldn’t afford anything less. Miller

products had to be more than the best they could be. They had to be the

best you could buy.

Today, the people that build and sell Miller products continue the

tradition. They’re just as committed to providing equipment and service

that meets the high standards of quality and value established in 1929.

This Owner’s Manual is designed to help you get the most out of your

Miller products. Please take time to read the Safety precautions. They

will help you protect yourself against potential hazards on the worksite.

We’ve made installation and operation quick

and easy. With Miller you can count on years

of reliable service with proper maintenance.

And if for some reason the unit needs repair,

there’s a Troubleshooting section that will

help you figure out what the problem is. The

parts list will then help you to decide the

exact part you may need to fix the problem.

Warranty and service information for your

particular model are also provided.

Miller is the first welding

equipment manufacturer in

the U.S.A. to be registered to

the ISO 9001 Quality System

Standard.

Working as hard as you do

− every power source from

Miller is backed by the most

hassle-free warranty in the

business.

From Miller to You

Mil_Thank 2009−09

DECLARATION OF CONFORMITY

for European Community (CE marked) products.

MILLER Electric Mfg. Co., 1635 Spencer Street, Appleton, WI 54914 U.S.A. declares that the

product(s) identified in this declaration conform to the essential requirements and provisions of

the stated Council Directive(s) and Standard(s).

Product/Apparatus Identification:

Product

Stock Number

S74 MPA PLUS 300577

Council Directives:

• 2006/95/EC Low Voltage

• 2004/108/EC Electromagnetic Compatibility

Standards:

• IEC 609741:2005 Arc welding equipment – Part 1: Welding power sources

• IEC 609745:2007 Arc welding equipment – Part 5: Wire feeders

• IEC 6097410:2007 Arc Welding Equipment – Part 10: Electromagnetic compatibility (EMC) requirements

• EN 50445:2008 Product family standard to demonstrate compliance of equipment for resistance welding,

arc welding and allied processes with the basic restrictions related to human exposure to electromagnetic

fields (0 Hz – 300Hz)

Signatory:

_____________________________________ ___________________________________________

David A. Werba

Date of Declaration

MANAGER, PRODUCT DESIGN COMPLIANCE

December 21, 2010

250868A

TABLE OF CONTENTS

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1.................................

1-1. Symbol Usage 1.......................................................................

1-2. Arc Welding Hazards 1.................................................................

1-3. Additional Symbols For Installation, Operation, And Maintenance 3.............................

1-4. California Proposition 65 Warnings 4......................................................

1-5. Principal Safety Standards 4.............................................................

1-6. EMF Information 4.....................................................................

SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE AVANT UTILISATION 5...........................

2-1. Symboles utilisés 5.....................................................................

2-2. Dangers relatifs au soudage à l’arc 5......................................................

2-3. Dangers supplémentaires en relation avec l’installation, le fonctionnement et la maintenance 7.....

2-4. Proposition californienne 65 Avertissements 8..............................................

2-5. Principales normes de sécurité 9.........................................................

2-6. Informations relatives aux CEM 9.........................................................

SECTION 3 − DEFINITIONS 11..................................................................

3-1. WEEE Label (For Products Sold Within The EU) 11..........................................

3-2. Symbols And Definitions 11...............................................................

SECTION 4 − INSTALLATION 12................................................................

4-1. Important Information Regarding CE Products (Sold Within The EU) 12..........................

4-2. Serial Number And Rating Label Location 12................................................

4-3. Specifications 12........................................................................

4-4. Site Selection 13........................................................................

4-5. Equipment Connection Diagrams 14.......................................................

4-6. Rear Panel Connections And Rotating Drive Assembly 15.....................................

4-7. 14-Pin Plug Information For Connecting Wire Feeder To Power Source 16........................

4-8. Wire Type, Size, And Optimal Wire Feed Speed Table 16......................................

4-9. Installing Welding Gun 17................................................................

4-10. Installing And Threading Welding Wire 18...................................................

SECTION 5 − OPERATION 19...................................................................

5-1. Power Switch 19........................................................................

5-2. Jog/Purge Switch 19....................................................................

5-3. Front Panel Controls 20..................................................................

5-4. Left Display 21.........................................................................

5-5. Right Display 21........................................................................

5-6. Adjust Control Left/Right 22...............................................................

5-7. Setup Push Button 22...................................................................

5-8. Start Push Button 22....................................................................

5-9. Crater Push Button 22...................................................................

5-10. Power Source Selection Menu 23..........................................................

5-11. Operational Terms 24....................................................................

SECTION 6 − SETTING SEQUENCE PARAMETERS 25............................................

6-1. Sequence Parameters In A Program 25.....................................................

SECTION 7 − PROGRAMMING 26...............................................................

7-1. Setup Menu 26.........................................................................

7-2. Setup Menu Level 2 27..................................................................

7-3. Setting A Start Sequence 28..............................................................

7-4. Setting A Crater Fill Sequence 29..........................................................

7-5. Profile Pulse 30.........................................................................

SECTION 8 − MAINTENANCE & TROUBLESHOOTING 31.........................................

8-1. Routine Maintenance 31.................................................................

8-2. Diagnostics 31.........................................................................

8-3. Troubleshooting 32......................................................................

SECTION 9 − ELECTRICAL DIAGRAM 34........................................................

SECTION 10 − PARTS LIST 36..................................................................

WARRANTY

OM-243 346 Page 1

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING

som _2010−03

Protect yourself and others from injury — read and follow these precautions.

1-1. Symbol Usage

DANGER! − Indicates a hazardous situation which, if

not avoided, will result in death or serious injury. The

possible hazards are shown in the adjoining symbols

or explained in the text.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible

hazards are shown in the adjoining symbols or ex-

plained in the text.

NOTICE − Indicates statements not related to personal injury.

. Indicates special instructions.

This group of symbols means Warning! Watch Out! ELECTRIC

SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult sym-

bols and related instructions below for necessary actions to avoid the

hazards.

1-2. Arc Welding Hazards

The symbols shown below are used throughout this manual

to call attention to and identify possible hazards. When you

see the symbol, watch out, and follow the related instructions

to avoid the hazard. The safety information given below is

only a summary of the more complete safety information

found in the Safety Standards listed in Section 1-5. Read and

follow all Safety Standards.

Only qualified persons should install, operate, maintain, and

repair this unit.

During operation, keep everybody, especially children, away.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The electrode and work circuit is

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. In semiautomatic or automatic

wire welding, the wire, wire reel, drive roll housing,

and all metal parts touching the welding wire are

electrically live. Incorrectly installed or improperly

grounded equipment is a hazard.

D Do not touch live electrical parts.

D Wear dry, hole-free insulating gloves and body protection.

D Insulate yourself from work and ground using dry insulating mats

or covers big enough to prevent any physical contact with the work

or ground.

D Do not use AC output in damp areas, if movement is confined, or if

there is a danger of falling.

D Use AC output ONLY if required for the welding process.

D If AC output is required, use remote output control if present on

unit.

D Additional safety precautions are required when any of the follow-

ing electrically hazardous conditions are present: in damp

locations or while wearing wet clothing; on metal structures such

as floors, gratings, or scaffolds; when in cramped positions such

as sitting, kneeling, or lying; or when there is a high risk of unavoid-

able or accidental contact with the workpiece or ground. For these

conditions, use the following equipment in order presented: 1) a

semiautomatic DC constant voltage (wire) welder, 2) a DC manual

(stick) welder, or 3) an AC welder with reduced open-circuit volt-

age. In most situations, use of a DC, constant voltage wire welder

is recommended. And, do not work alone!

D Disconnect input power or stop engine before installing or

servicing this equipment. Lockout/tagout input power according to

OSHA 29 CFR 1910.147 (see Safety Standards).

D Properly install and ground this equipment according to its

Owner’s Manual and national, state, and local codes.

D Always verify the supply ground − check and be sure that input

power cord ground wire is properly connected to ground terminal in

disconnect box or that cord plug is connected to a properly

grounded receptacle outlet.

D When making input connections, attach proper grounding conduc-

tor first − double-check connections.

D Keep cords dry, free of oil and grease, and protected from hot metal

and sparks.

D Frequently inspect input power cord for damage or bare wiring −

replace cord immediately if damaged − bare wiring can kill.

D Turn off all equipment when not in use.

D Do not use worn, damaged, undersized, or poorly spliced cables.

D Do not drape cables over your body.

D If earth grounding of the workpiece is required, ground it directly

with a separate cable.

D Do not touch electrode if you are in contact with the work, ground,

or another electrode from a different machine.

D Do not touch electrode holders connected to two welding ma-

chines at the same time since double open-circuit voltage will be

present.

D Use only well-maintained equipment. Repair or replace damaged

parts at once. Maintain unit according to manual.

D Wear a safety harness if working above floor level.

D Keep all panels and covers securely in place.

D Clamp work cable with good metal-to-metal contact to workpiece

or worktable as near the weld as practical.

D Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

D Do not connect more than one electrode or work cable to any

single weld output terminal.

SIGNIFICANT DC VOLTAGE exists in inverter weld-

ing power sources AFTER removal of input power.

D Turn Off inverter, disconnect input power, and discharge input

capacitors according to instructions in Maintenance Section

before touching any parts.

HOT PARTS can burn.

D Do not touch hot parts bare handed.

D Allow cooling period before working on equip-

ment.

D To handle hot parts, use proper tools and/or

wear heavy, insulated welding gloves and

clothing to prevent burns.

OM-243 346 Page 2

Welding produces fumes and gases. Breathing

these fumes and gases can be hazardous to your

health.

FUMES AND GASES can be hazardous.

D Keep your head out of the fumes. Do not breathe the fumes.

D If inside, ventilate the area and/or use local forced ventilation at the

arc to remove welding fumes and gases.

D If ventilation is poor, wear an approved air-supplied respirator.

D Read and understand the Material Safety Data Sheets (MSDSs)

and the manufacturer’s instructions for metals, consumables,

coatings, cleaners, and degreasers.

D Work in a confined space only if it is well ventilated, or while

wearing an air-supplied respirator. Always have a trained watch-

person nearby. Welding fumes and gases can displace air and

lower the oxygen level causing injury or death. Be sure the breath-

ing air is safe.

D Do not weld in locations near degreasing, cleaning, or spraying op-

erations. The heat and rays of the arc can react with vapors to form

highly toxic and irritating gases.

D Do not weld on coated metals, such as galvanized, lead, or

cadmium plated steel, unless the coating is removed from the weld

area, the area is well ventilated, and while wearing an air-supplied

respirator. The coatings and any metals containing these elements

can give off toxic fumes if welded.

Arc rays from the welding process produce intense

visible and invisible (ultraviolet and infrared) rays

that can burn eyes and skin. Sparks fly off from the

weld.

D Wear an approved welding helmet fitted with a proper shade of

filter lenses to protect your face and eyes from arc rays and

sparks when welding or watching (see ANSI Z49.1 and Z87.1

listed in Safety Standards).

D Wear approved safety glasses with side shields under your

helmet.

D Use protective screens or barriers to protect others from flash,

glare and sparks; warn others not to watch the arc.

D Wear protective clothing made from durable, flame-resistant

material (leather, heavy cotton, or wool) and foot protection.

ARC RAYS can burn eyes and skin.

Welding on closed containers, such as tanks,

drums, or pipes, can cause them to blow up. Sparks

can fly off from the welding arc. The flying sparks, hot

workpiece, and hot equipment can cause fires and

burns. Accidental contact of electrode to metal objects can cause

sparks, explosion, overheating, or fire. Check and be sure the area is

safe before doing any welding.

WELDING can cause fire or explosion.

D Remove all flammables within 35 ft (10.7 m) of the welding arc. If

this is not possible, tightly cover them with approved covers.

D Do not weld where flying sparks can strike flammable material.

D Protect yourself and others from flying sparks and hot metal.

D Be alert that welding sparks and hot materials from welding can

easily go through small cracks and openings to adjacent areas.

D Watch for fire, and keep a fire extinguisher nearby.

D Be aware that welding on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

D Do not weld on closed containers such as tanks, drums, or pipes,

unless they are properly prepared according to AWS F4.1 (see

Safety Standards).

D Do not weld where the atmosphere may contain flammable dust,

gas, or liquid vapors (such as gasoline).

D Connect work cable to the work as close to the welding area as

practical to prevent welding current from traveling long, possibly

unknown paths and causing electric shock, sparks, and fire

hazards.

D Do not use welder to thaw frozen pipes.

D Remove stick electrode from holder or cut off welding wire at

contact tip when not in use.

D Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

D Remove any combustibles, such as a butane lighter or matches,

from your person before doing any welding.

D After completion of work, inspect area to ensure it is free of sparks,

glowing embers, and flames.

D Use only correct fuses or circuit breakers. Do not oversize or by-

pass them.

D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B

for hot work and have a fire watcher and extinguisher nearby.

FLYING METAL or DIRT can injure eyes.

D Welding, chipping, wire brushing, and grinding

cause sparks and flying metal. As welds cool,

they can throw off slag.

D Wear approved safety glasses with side

shields even under your welding helmet.

BUILDUP OF GAS can injure or kill.

D Shut off shielding gas supply when not in use.

D Always ventilate confined spaces or use

approved air-supplied respirator.

ELECTRIC AND MAGNETIC FIELDS (EMF

)

can affect Implanted Medical Devices.

D Wearers of Pacemakers and other Implanted

Medical Devices should keep away.

D Implanted Medical Device wearers should consult their doctor

and the device manufacturer before going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating

operations.

NOISE can damage hearing.

Noise from some processes or equipment can

damage hearing.

D Wear approved ear protection if noise level is

high.

Shielding gas cylinders contain gas under high

pressure. If damaged, a cylinder can explode. Since

gas cylinders are normally part of the welding

process, be sure to treat them carefully.

CYLINDERS can explode if damaged.

D Protect compressed gas cylinders from excessive heat, mechani-

cal shocks, physical damage, slag, open flames, sparks, and arcs.

D Install cylinders in an upright position by securing to a stationary

support or cylinder rack to prevent falling or tipping.

D Keep cylinders away from any welding or other electrical circuits.

D Never drape a welding torch over a gas cylinder.

D Never allow a welding electrode to touch any cylinder.

D Never weld on a pressurized cylinder − explosion will result.

D Use only correct shielding gas cylinders, regulators, hoses, and fit-

tings designed for the specific application; maintain them and

associated parts in good condition.

D Turn face away from valve outlet when opening cylinder valve.

D Keep protective cap in place over valve except when cylinder is in

use or connected for use.

D Use the right equipment, correct procedures, and sufficient num-

ber of persons to lift and move cylinders.

D Read and follow instructions on compressed gas cylinders,

associated equipment, and Compressed Gas Association (CGA)

publication P-1 listed in Safety Standards.

OM-243 346 Page 3

1-3. Additional Symbols For Installation, Operation, And Maintenance

FIRE OR EXPLOSION hazard.

D Do not install or place unit on, over, or near

combustible surfaces.

D Do not install unit near flammables.

D Do not overload building wiring − be sure power supply system is

properly sized, rated, and protected to handle this unit.

FALLING EQUIPMENT can injure.

D Use lifting eye to lift unit only, NOT running

gear, gas cylinders, or any other accessories.

D Use equipment of adequate capacity to lift and

support unit.

D If using lift forks to move unit, be sure forks are long enough to

extend beyond opposite side of unit.

D Keep equipment (cables and cords) away from moving vehicles

when working from an aerial location.

D Follow the guidelines in the Applications Manual for the Revised

NIOSH Lifting Equation (Publication No. 94−110) when manu-

ally lifting heavy parts or equipment.

OVERUSE can cause OVERHEATING

D Allow cooling period; follow rated duty cycle.

D Reduce current or reduce duty cycle before

starting to weld again.

D Do not block or filter airflow to unit.

FLYING SPARKS can injure.

D Wear a face shield to protect eyes and face.

D Shape tungsten electrode only on grinder with

proper guards in a safe location wearing proper

face, hand, and body protection.

D Sparks can cause fires — keep flammables away.

STATIC (ESD) can damage PC boards.

D Put on grounded wrist strap BEFORE handling

boards or parts.

D Use proper static-proof bags and boxes to

store, move, or ship PC boards.

MOVING PARTS can injure.

D Keep away from moving parts.

D Keep away from pinch points such as drive

rolls.

WELDING WIRE can injure.

D Do not press gun trigger until instructed to do

so.

D Do not point gun toward any part of the body,

other people, or any metal when threading

welding wire.

MOVING PARTS can injure.

D Keep away from moving parts such as fans.

D Keep all doors, panels, covers, and guards

closed and securely in place.

D Have only qualified persons remove doors, panels, covers, or

guards for maintenance and troubleshooting as necessary.

D Reinstall doors, panels, covers, or guards when maintenance is

finished and before reconnecting input power.

READ INSTRUCTIONS.

D Read and follow all labels and the Owner’s

Manual carefully before installing, operating, or

servicing unit. Read the safety information at

the beginning of the manual and in each

section.

D Use only genuine replacement parts from the manufacturer.

D Perform maintenance and service according to the Owner’s

Manuals, industry standards, and national, state, and local

codes.

H.F. RADIATION can cause interference.

D High-frequency (H.F.) can interfere with radio

navigation, safety services, computers, and

communications equipment.

D Have only qualified persons familiar with

electronic equipment perform this installation.

D The user is responsible for having a qualified electrician prompt-

ly correct any interference problem resulting from the installa-

tion.

D If notified by the FCC about interference, stop using the

equipment at once.

D Have the installation regularly checked and maintained.

D Keep high-frequency source doors and panels tightly shut, keep

spark gaps at correct setting, and use grounding and shielding to

minimize the possibility of interference.

ARC WELDING can cause interference.

D Electromagnetic energy can interfere with

sensitive electronic equipment such as

computers and computer-driven equipment

such as robots.

D Be sure all equipment in the welding area is

electromagnetically compatible.

D To reduce possible interference, keep weld cables as short as

possible, close together, and down low, such as on the floor.

D Locate welding operation 100 meters from any sensitive elec-

tronic equipment.

D Be sure this welding machine is installed and grounded

according to this manual.

D If interference still occurs, the user must take extra measures

such as moving the welding machine, using shielded cables,

using line filters, or shielding the work area.

OM-243 346 Page 4

1-4. California Proposition 65 Warnings

Welding or cutting equipment produces fumes or gases

which contain chemicals known to the State of California to

cause birth defects and, in some cases, cancer. (California

Health & Safety Code Section 25249.5 et seq.)

Battery posts, terminals and related accessories contain lead

and lead compounds, chemicals known to the State of

California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling.

This product contains chemicals, including lead, known to

the state of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after use.

For Gasoline Engines:

Engine exhaust contains chemicals known to the State of

California to cause cancer, birth defects, or other reproduc-

tive harm.

For Diesel Engines:

Diesel engine exhaust and some of its constituents are

known to the State of California to cause cancer, birth

defects, and other reproductive harm.

1-5. Principal Safety Standards

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

from Global Engineering Documents (phone: 1-877-413-5184, website:

www.global.ihs.com).

Safe Practices for the Preparation of Containers and Piping for Welding

and Cutting, American Welding Society Standard AWS F4.1, from Glob-

al Engineering Documents (phone: 1-877-413-5184, website:

www.global.ihs.com).

National Electrical Code, NFPA Standard 70, from National Fire Protec-

tion Association, Quincy, MA 02269 (phone: 1-800-344-3555, website:

www.nfpa.org and www. sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

from Compressed Gas Association, 4221 Walney Road, 5th Floor,

Chantilly, VA 20151 (phone: 703-788-2700, website:www.cganet.com).

Safety in Welding, Cutting, and Allied Processes, CSA Standard

W117.2, from Canadian Standards Association, Standards Sales, 5060

Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (phone:

800-463-6727, website: www.csa-international.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, from American National Standards Institute,

25 West 43rd Street, New York, NY 10036 (phone: 212-642-4900, web-

site: www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, from National Fire Protection Association,

Quincy, MA 02269 (phone: 1-800-344-3555, website: www.nfpa.org.

OSHA, Occupational Safety and Health Standards for General Indus-

try, Title 29, Code of Federal Regulations (CFR), Part 1910, Subpart Q,

and Part 1926, Subpart J, from U.S. Government Printing Office, Super-

intendent of Documents, P.O. Box 371954, Pittsburgh, PA 15250-7954

(phone: 1-866-512-1800) (there are 10 OSHA Regional Offices—

phone for Region 5, Chicago, is 312-353-2220, website:

www.osha.gov).

U.S. Consumer Product Safety Commission (CPSC), 4330 East West

Highway, Bethesda, MD 20814 (phone: 301-504-7923, website:

www.cpsc.gov).

Applications Manual for the Revised NIOSH Lifting Equation, The Na-

tional Institute for Occupational Safety and Health (NIOSH), 1600

Clifton Rd, Atlanta, GA 30333 (phone: 1-800-232-4636, website:

www.cdc.gov/NIOSH).

1-6. EMF Information

Electric current flowing through any conductor causes localized electric

and magnetic fields (EMF). Welding current creates an EMF field

around the welding circuit and welding equipment. EMF fields may inter-

fere with some medical implants, e.g. pacemakers. Protective

measures for persons wearing medical implants have to be taken. For

example, access restrictions for passers−by or individual risk assess-

ment for welders. All welders should use the following procedures in

order to minimize exposure to EMF fields from the welding circuit:

1. Keep cables close together by twisting or taping them, or using a

cable cover.

2. Do not place your body between welding cables. Arrange cables

to one side and away from the operator.

3. Do not coil or drape cables around your body.

4. Keep head and trunk as far away from the equipment in the

welding circuit as possible.

5. Connect work clamp to workpiece as close to the weld as

possible.

6. Do not work next to, sit or lean on the welding power source.

7. Do not weld whilst carrying the welding power source or wire

feeder.

About Implanted Medical Devices:

Implanted Medical Device wearers should consult their doctor and the

device manufacturer before performing or going near arc welding, spot

welding, gouging, plasma arc cutting, or induction heating operations.

If cleared by your doctor, then following the above procedures is recom-

mended.

Page is loading ...

OM-243 346 Page 9

2-5. Principales normes de sécurité

Safety in Welding, Cutting, and Allied Processes, ANSI Standard Z49.1,

de Global Engineering Documents (téléphone : 1-877-413-5184, site

Internet : www.global.ihs.com).

Safe Practices for the Preparation of Containers and Piping for Welding

and Cutting, American Welding Society Standard AWS F4.1, de Global

Engineering Documents (téléphone : 1-877-413-5184, site internet :

www.global.ihs.com).

National Electrical Code, NFPA Standard 70, de National Fire Protec-

tion Association, Quincy, MA 02269 (téléphone : 800-344-3555, site

Internet : www.nfpa.org et www.sparky.org).

Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,

de Compressed Gas Association, 4221 Walney Road, 5th Floor, Chan-

tilly, VA 20151 (téléphone : 703-788-2700, site Internet :

www.cganet.com).

Safety in Welding, Cutting, and Allied Processes, CSA Standard

W117.2, de Canadian Standards Association, Standards Sales, 5060

Spectrum Way, Suite 100, Ontario, Canada L4W 5NS (téléphone :

800-463-6727, site internet : www.csa-international.org).

Safe Practice For Occupational And Educational Eye And Face Protec-

tion, ANSI Standard Z87.1, de American National Standards Institute,

25 West 43rd Street, New York, NY 10036 (téléphone : 212-642-4900,

site Internet : www.ansi.org).

Standard for Fire Prevention During Welding, Cutting, and Other Hot

Work, NFPA Standard 51B, de National Fire Protection Association,

P.O. Box 9101, Quincy, MA 02269-9101 (téléphone : 617-770-3000,

site Internet : www.nfpa.org).

OSHA, Occupational Safety and Health Standards for General

Industry, Title 29, Code of Federal Regulations (CFR), Part 1910,

Subpart Q, and Part 1926, Subpart J, de U.S. Government Printing

Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA

15250-7954 (téléphone : 1-866-512-1800) (il y a 10 bureaux

régionaux−le téléphone de la région 5, Chicago, est 312-353-2220, site

Internet : www.osha.gov).

U.S. Consumer Product Safety Commission (CPSC), 4330 East West

Highway, Bethesda, MD 20814 (téléphone : 301-504-7923, site inter-

net : www.cpsc.gov).

Applications Manual for the Revised NIOSH Lifting Equation, The

National Institute for Occupational Safety and Health (NIOSH), 1600

Clifton Rd, Atlanta, GA 30333 (télé[hone : 1-800-232-4636, site internet:

www.cdc.gov/NIOSH).

2-6. Informations relatives aux CEM

Le courant électrique qui traverse tout conducteur génère des champs

électromagnétiques (CEM) à certains endroits. Le courant de soudage

crée un CEM autour du circuit et du matériel de soudage. Les CEM

peuvent créer des interférences avec certains implants médicaux

comme des stimulateurs cardiaques. Des mesures de protection pour

les porteurs d’implants médicaux doivent être prises: par exemple, des

restrictions d’accès pour les passants ou une évaluation individuelle

des risques pour les soudeurs. Tous les soudeurs doivent appliquer les

procédures suivantes pour minimiser l’exposition aux CEM provenant

du circuit de soudage:

1. Rassembler les câbles en les torsadant ou en les attachant avec

du ruban adhésif ou avec une housse.

2. Ne pas se tenir au milieu des câbles de soudage. Disposer les

câbles d’un côté et à distance de l’opérateur.

3. Ne pas courber et ne pas entourer les câbles autour de votre

corps.

4. Maintenir la tête et le torse aussi loin que possible du matériel du

circuit de soudage.

5. Connecter la pince sur la pièce aussi près que possible de la

soudure.

6. Ne pas travailler à proximité d’une source de soudage, ni

s’asseoir ou se pencher dessus.

7. Ne pas souder tout en portant la source de soudage ou le

dévidoir.

En ce qui concerne les implants médicaux :

Les porteurs d’implants doivent d’abord consulter leur médecin avant

de s’approcher des opérations de soudage à l’arc, de soudage par

points, de gougeage, du coupage plasma ou de chauffage par induc-

tion. Si le médecin approuve, il est recommandé de suivre les

procédures précédentes.

Page is loading ...

OM-243 346 Page 11

SECTION 3 − DEFINITIONS

3-1. WEEE Label (For Products Sold Within The EU)

Do not discard product (where ap-

plicable) with general waste.

Reuse or recycle Waste Electrical

and Electronic Equipment (WEEE)

by disposing at a designated collec-

tion facility.

Contact your local recycling office

or your local distributor for further

information.

3-2. Symbols And Definitions

. Some symbols are found only on CE products.

Amperes

Volts Alternating Current

Duty Cycle

Degree Of

Protection

Hertz Program Wire Feed

Jog Output Trigger Line Connection

Set Up Sequence Trigger Hold On Trigger Hold Off

Purge Press To Set Start Crater

Time Preflow Time Postflow Time Read Instructions

Increase

Primary Current

Rated Current

Load Voltage

Primary Voltage

Dual Schedule

OM-243 346 Page 12

SECTION 4 − INSTALLATION

4-1. Important Information Regarding CE Products (Sold Within The EU)

A. Information On Electromagnetic Fields (EMF)

! This equipment shall not be used by the general public as the EMF limits for the general public might be exceeded during welding.

This equipment is built in accordance with EN 60974−1 and is intended to be used only in an occupational environment (where the general public

access is prohibited or regulated in such a way as to be similar to occupational use) by an expert or an instructed person.

Wire feeders and ancillary equipment (such as torches, liquid cooling systems and arc striking and stabilizing devices) as part of the welding

circuit may not be a major contributor to the EMF. See the Owner’s Manuals for all components of the welding circuit for additional EMF exposure

information.

S The EMF assessment on this equipment was conducted at 0.5 meter.

S At a distance of 1 meter the EMF exposure values were less than 20% of the permissible values.

ce-emf 1 2010-10

B. Information On Electromagnetic Compatibility (EMC)

! This Class A equipment is not intended for use in residential locations where the electrical power is provided by the public low−

voltage supply system. There may be potential difficulties in ensuring electromagnetic compatibility in those locations, due to

conducted as well as radiated disturbances.

ce-emc 3 2010-10

4-2. Serial Number And Rating Label Location

The serial number and rating information for this product is located on the rear panel. Use rating label to determine input power requirements and/or

rated output. For future reference, write serial number in space provided on back cover of this manual.

4-3. Specifications

Type of Input

Power

Welding Power

Source Type

Wire Feed Speed*

Wire Diameter

Range

Welding

Circuit

Rating

Overall

Dimensions

Weight

24 Volts AC

Single-Phase

10 Amperes

50/60 Hertz

Constant Voltage (CV)

DC With 14-Pin And

Contactor Control

Standard:

50 To 780 ipm

(1.3 To 19.8 mpm)

Optional High Speed:

92 to 1435 ipm

(2.3 to 36.4 mpm)

.035 To 5/64 in.

(0.9 To 2 mm)

Max Spool

Capacity:

18 in. (457 mm)

Max Spool

Weight: 60 lb

(27 kg)

100 Volts,

750

Amperes,

100% Duty

Cycle

IP 21S Length: 27 in.

(686 mm)

Width: 12-1/2 in.

(318 mm)

Height: 14 in.

(356 mm)

45 lb

(20.4 kg)

* See Section 4-8 for detailed information on wire type, wire size, and wire feed speed.

OM-243 346 Page 13

Ref. 803 048 / 246 044-A

! Do not put feeder where

welding wire hits cylinder.

! Do not move or operate

equipment when it could

tip.

1 Wire Feeder

2 Wire Spool/Reels

3 Gas Cylinder w/Hose And

Regulator (Customer

Supplied)

. Shielding gas pressure not to

exceed 100 psi (689 kPa).

4 Welding Power Source

5 Running Gear

6 Water Cooling System

4-4. Site Selection

OM-243 346 Page 14

4-5. Equipment Connection Diagrams

1 Welding Power Source

. Select welding power source

according to Section 5-10.

2 Contactor Control/Power Cord

3 Positive (+) Weld Cable

4 Negative (−) Weld Cable

5 Workpiece

6 Welding Gun

7 Wire Feeder

8 Gas Hose

9 Gas Cylinder and Regulator

(Customer Supplied)

. Shielding gas pressure not to

exceed 100 psi (689 kPa).

246 040-A

OM-243 346 Page 15

4-6. Rear Panel Connections And Rotating Drive Assembly

246 041-A

1 14-Pin Control Cable - 15 Ft

(4.6 m)

2 Shielding Gas Valve Fittings

Requires fitting with 5/8-18 right-

hand threads. Connect customer-

supplied gas hose.

3 Weld Cable Terminal

4 Weld Cable

5 Drive Assembly

6 Drive Assembly Rotation

Knob

To rotate the drive assembly, loos-

en drive assembly rotation knob,

rotate drive assembly, and tighten

knob.

9/16, 5/8 in.

Tools Needed:

3/16 in.

OM-243 346 Page 16

4-7. 14-Pin Plug Information For Connecting Wire Feeder To Power Source

Pin* Pin Information

A 24 volts AC with respect to socket G.

B Contact closure to A completes 24 volts AC contactor control circuit.

G Circuit common for 24 volts AC circuit.

C +10 volts DC input from power source to wire feeder with respect to socket D.

D Remote control circuit common.

E 0 to +10 volts DC output signal from wire feeder to power source with respect to socket D.

H Voltage feedback; 0 to +10 volts DC, 1 volt per 10 arc volts.

F Current feedback; 0 to +10 volts DC, 1 volt per 100 amperes.

L 0 to +10 volts DC output signal from wire feeder to power source with respect to socket N.

M CC/CV select 0 to +10 volts DC.

N Feeder common.

K Not used.

*The remaining pins are not used.

4-8. Wire Type, Size, And Optimal Wire Feed Speed Table

Motor Speed Wire Type Wire Size Rated Speed Range (per IEC 60974−5)

Standard All .035 To .062 in. (0.9 To 1.57 mm) 55 To 770 ipm (1.4 To 19.6 mpm)

Standard All 5/64 in. (2 mm) 55 To 700 ipm (1.4 To 17.8 mpm)

Notes

OM-243 346 Page 17

4-9. Installing Welding Gun

245 985-A / Ref. 246 040-A

1 Power Clamp Knob

2 Gun Locking Tab

3 Power Pin Groove

4 Gun Connection End

Installing gun with Accu-Mate

connection

Loosen power clamp knob to allow

power pin of gun to clear the gun

locking tab.

Push power pin into power clamp

as far as possible to align the

groove in the power pin of the gun

with the gun locking tab.

Secure gun by tightening power

clamp knob.

Installing gun without Accu-

Mate connection

When using a gun without the

groove in the power pin, loosen

power clamp knob and rotate gun

locking tab 180 degrees. This pre-

vents the locking tab from extend-

ing into the power pin gun connec-

tion.

Push power pin into power clamp

as far as possible.

Secure gun by tightening power

clamp knob.

5 Gun Control Cable

Insert plug into Gun Control

receptacle, and tighten threaded

collar.

6 Pressure Blocking Clip

7 Empty Pressure Slots

Installing A Push/Pull Gun

When using a push/pull gun, leave

pressure blocking clips in position.

Do not adjust pressure as shown in

Section 4-10.

Installing A Push Only Gun

When using a push only gun, re-

move the blocking clips and place

them in the empty pressure slots for

storage and adjust pressure as

shown in Section 4-10.

Installing gun with

Accu-Mate connection

Installing gun without

Accu-Mate connection

OM-243 346 Page 18

4-10. Installing And Threading Welding Wire

Ref. 156 929-A / Ref. 150 922 / Ref. 156 930 / S-0627-A

Tools Needed:

. For best wire feeding performance, be

sure that the outlet cable has the proper

size liner for the welding wire size being

used. Also, when the gun is installed, the

liner extending from the back of the gun

should be as close to the drive rolls as

possible, without touching.

Install gun. Lay gun cable out straight. Cut off

end of wire. Push wire through guides up to

drive rolls; continue to hold wire. Press Jog

button to feed wire out gun.

. When using a push/pull gun and pressure

blocking clips, do not adjust pressure.

. For aluminum wire set pressure indicator

scale as light as possible.

. To adjust drive roll pressure, hold nozzle

about 2 in (51 mm) from nonconductive

surface and press gun trigger to feed wire

against surface. Tighten knob so wire

does not slip. Do not overtighten. If con-

tact tip is completely blocked, wire should

slip at the feeder (see pressure adjust-

ment above).Cut wire off. Close cover.

NONCONDUCTIVE

SURFACE

NONCONDUCTIVE

SURFACE

No Wire Slip

Wire Slips

Install wire spool. Adjust tension nut so

wire is taut when wire feed stops.

Install wire guides and

anti-wear guide.

Install drive rolls.

3/16, 5/64 in.

15/16, 3/8 in.

Pressure

Adjust

Front

Rolls

Pressure

Adjust

Rear

Rolls

Drive Rolls

End Of Liner

Back Of Gun

Pressure

Indicator

Scale

OM-243 346 Page 19

SECTION 5 − OPERATION

5-1. Power Switch

1 Power Switch

Ref. 246 039-A

5-2. Jog/Purge Switch

Ref. 246 039-A

1 Jog/Purge Switch

Pressing the Jog/Purge switch allows the op-

erator to jog wire without energizing the weld

power or gas valve circuit.

• The unit provides the ability to jog the wire

feeder by means of the gun trigger or the

Jog/Purge switch.

• If the welding arc does not initiate in 3 sec-

onds after the gun trigger is activated, the

unit will perform a jog operation for a maxi-

mum of two minutes. If the gun trigger is still

activated after two minutes, the jog opera-

tion is terminated to prevent complete des-

pooling of the wire, in the case of a damaged

gun.

• The unit displays the “TRIG ERR“ message

to inform the operator that the trigger is acti-

vated.

• Jog speed can be adjusted by the Adjust

control when the unit is jogging wire. The

unit displays jog speed when the unit is be-

ing jogged.

• Jogging can also be accomplished by

pressing the Jog/Purge button.

• Pressing the Jog/Purge button also allows

the operator to purge gas lines before weld-

ing and to preset gas pressure at the

regulator.

OM-243 346 Page 20

5-3. Front Panel Controls

1 Adjust Control Left

(See Section 5-6)

2 Left Display (See Section 5-4)

3 Right Display (See Section 5-5)

4 Adjust Control Right

(See Section 5-6)

5 Crater Push Button

(See Section 5-9)

6 Start Push Button (See Section 5-8)

7 Setup Push Button

(See Section 5-7)

243 898-A

Notes

OM-243 346 Page 21

5-4. Left Display

1 Left Side Schedule A LED

2 Left Side Schedule B LED

3 Left Display

4 Arc Length LED

5 Volts LED

. To set the correct voltage range for a par-

ticular power source, see Section 5-10 −

Power Source Selection Menu.

Left Display

The left display shows voltage or arc length.

The unit displays both preset and actual arc

voltage. When the unit is in a welding state,

actual arc voltage is displayed.

. See Section 7-2 for selection of arc length

and voltage display.

5-5. Right Display

1 Right Side Schedule A LED

2 Right Side Schedule B LED

3 Right Display

The right display shows wire feed speed or

amperage. The unit displays and adjusts only

preset wire feed speed at idle. When the unit

is in a welding state, actual wire feed speed is

displayed for the active welding sequence.

4 Wire Feed Speed LED

5 Amps LED

The LEDs below the display illuminate to indi-

cate which value is being shown.

• If the unit is in a welding state that does not

involve feeding wire, the unit displays the

weld sequence wire feed speed. At any time

during welding, the weld sequence wire

feed speed can be adjusted and overrides

the preset wire feed speed display. In other

words, if the Adjust control is activated while

welding, the unit displays and permits ad-

justment of the weld sequence wire feed

speed regardless of the active welding se-

quence.

• When the unit is displaying amperage, the

Amps LED illuminates. Amperage is only

displayed if the unit is in a welding state and

the amperage is above a minimum value of

25 Amps.

Page is loading ...

Miller MB060031U, S-74 MPA PLUS, S-74S Owner's manual

Other documents