Whirlpool AKR 029 IX User guide

Category
Cooker hoods
Type
User guide
5019 318 33287
INSTALLATION - MONTAGEANLEITUNG
Der Mindestabstand zwischen dem Kochfeld und der unteren Kante der Dunstabzugshaube MUSS bei
Elektroplatten 50 cm und bei Gas- oder kombinierten Herden 65 cm betragen. Überprüfen Sie vor der
Installation auch die im Handbuch des Kochfeldes angegebenen Abstände.
Die Installation der Abzugshaube muss von einer Fachkraft ausgeführt werden.
Schließen Sie das Gerät erst nach seiner kompletten Installation an das Stromnetz an.
WARNUNG: Aufgrund des schweren Gewichtes sind mindestens zwei oder noch mehr Personen zur
Beförderung und Installation der Dunstabzugshaube erforderlich.
WARNUNG: Prüfen Sie, ob das Abluftrohr und die Befestigungsmanschetten im Lieferumfang inbegriffen
sind. Andernfalls sind sie separat zu beziehen.
Hinweise zu Installation und Gebrauch: Lesen sie vor dem Gebrauch der Dunstabzugshaube die vorliegende
Gebrauchsanweisung aufmerksam durch. Der Hersteller lehnt jede Haftung für Störungen, Schäden oder Feuer
ab, die bei Missachtung der vorliegenden Gebrauchsanweisungen durch das Gerät entstehen sollten.
INSTALLATION - ASSEMBLY INSTRUCTIONS
The minimum distance between the support surface of the recipients on the cooking device and the lowest part
of the hood MUST NOT BE less than 50 cm in the case of electric cookers and 65 cm for gas or combination
cookers. Before installation, moreover, check the distances specified in the hob’s user manual.
Hood installation must be carried out by a qualified technician.
Do not connect the appliance to the mains power supply until installation has been completed.
WARNING: Very heavy product; hood handling and installation must be carried out by at least two persons.
WARNING: Check whether the exhaust pipe and clamps are provided. If not, they must be purchased
separately.
Note on installation and use: Read this manual carefully before installing or using the hood. The Manufacturer
declines any liability for problems, fires or damage caused to the appliance due to non-compliance with the
instructions given in this manual.
INSTALLATION - INSTRUCTIONS DE MONTAGE
La distance minimum entre la surface de support des récipients sur le dispositif de cuisson et la partie la plus basse
de la hotte NE DOIT PAS ÊTRE inférieure à 50 cm pour les cuisinières électriques et à 65 cm pour les cuisinières à
gaz ou mixtes. Avant l’installation, il convient de vérifier les distances indiquées dans le manuel de la table de cuisson.
L’installation de la hotte doit être confiée à un technicien qualifié.
Ne branchez pas l’appareil tant que l’installation n’est pas terminée.
AVERTISSEMENT : Appareil excessivement lourd ; la manutention et l’installation de la hotte doivent être
effectuées par deux personnes ou plus.
AVERTISSEMENT : Vérifiez si le conduit d’évacuation et les colliers de fixation sont fournis avec l’appareil.
Dans le cas contraire, il conviendra de les acheter.
Remarque pour le montage et l’utilisation : Avant de monter ou d’utiliser la hotte, lisez attentivement ce
manuel. Le fabricant décline toute responsabilité en cas d’inconvénients, dommages ou incendies provoqués par
l’appareil et dus à la non-observation des instructions contenues dans cette notice.
INSTALLATIE - MONTAGE-INSTRUCTIES
De minimale afstand tussen het steunoppervlak van de pannen op het kooktoestel en het laagste deel van de
afzuigkap MAG NIET minder dan 50 cm zijn bij elektrische kooktoestellen en 65 cm bij kooktoestellen op gas of
gemengd. Controleer bovendien de afstanden die in de handleiding van de kookplaat zijn vermeld, voordat u de
kap installeert.
De installatie van de afzuigkap moet worden uitgevoerd door een gekwalificeerd technicus.
Sluit het apparaat niet op het elektriciteitsnet aan voordat de installatie voltooid is.
WAARSCHUWING: aangezien dit apparaat zwaar is, dient het door minstens twee of meer personen
verplaatst en geïnstalleerd te worden.
WAARSCHUWING: controleer of de afvoerpijp en de klembanden bijgeleverd zijn. Zo niet, dan moeten
ze apart worden aangeschaft.
Opmerking voor installatie en gebruik: lees voordat u de afzuigkap installeert of gebruikt deze handleiding
zorgvuldig door. De fabrikant aanvaardt geen enkele verantwoordelijkheid voor problemen, schade of brand die
veroorzaakt is door het niet naleven van de instructies in deze handleiding.
D
GB
F
NL
5019 318 33287
SAFEGUARDING THE ENVIRONMENT
1. Packing
Packing materials are 100% recyclable and are marked with the
recycling symbol .Comply with the local regulations for
disposal. The packing materials (plastic bags, polystyrene, etc.)
are a potential source of danger and must be kept out of the
reach of children.
2. Product
This appliance is marked in compliance with European Directive
2002/96/EC, Waste Electrical and Electronic Equipment (WEEE).
By ensuring that this appliance is correctly scrapped, the user can
help prevent potentially harmful consequences for the
environment and the health of people.
The symbol on the product or the accompanying
documentation indicates that this product should not be treated
as domestic waste but must be taken to a suitable collection
centre for the recycling of electrical and electronic equipment.
Disposal must be carried out in compliance with local regulations
on waste disposal.
For further information on the treatment, recovery and recycling
of this product, contact the competent local office, the
household waste collection service or the shop where you
purchased the appliance.
IMPORTANT INSTRUCTIONS FOR
SAFETY
WARNING: To reduce the risk of accidents, electric shock,
injury or damage, when using the hood comply with the basic
precautions, including the following.
1. Always disconnect the hood from the power supply before
carrying out any installation or maintenance operation on the
appliance.
2. Installation must be carried out by a specialised technician, in
compliance with the manufacturer’s instructions and local
safety regulations.
3. Earthing of the appliance is compulsory. (Not possible for
Class II hoods).
4. Never use multisockets and extension leads.
5. The electrical components must no longer be accessible to
the user after installation.
6. Do not touch the hood with wet parts of the body or use it
when barefoot.
7. Do not pull the appliance power cable to unplug it.
8. After-sales service – do not repair or replace any part of the
hood unless specifically indicated in the manual. All other
maintenance services must be carried out by a specialised
technician.
9. When drilling the wall, make sure not to damage the
electrical connections and/or pipes.
10. The ventilation ducts must always discharge to the outside.
11. The Manufacturer declines any liability for improper use or
incorrect setting of the controls.
12. The appliance is not intended for use by children or persons
with limited physical, sensory or mental abilities or without
experience and knowledge of it, unless they are under the
supervision of or instructed in its use by a person responsible
for their safety.
13. Keep children away.
14. To reduce the risk of fire, only use a metal inlet duct.
15. Children must be supervised so that they do not play with
the appliance.
16. The product must be disposed of in compliance with local
regulations on waste disposal.
17. For further information on the treatment, recovery and
recycling of this product, contact the competent local office,
the household waste collection service or the shop where
you purchased the appliance.
18. Regular cleaning and maintenance is essential for correct
hood operation and good performance. Frequently clean all
encrustations from dirty surfaces to prevent the
accumulation of grease. Regularly clean or replace filters.
19. Do not “flambé” food under the hood. Naked flames could
cause a fire.
20. The room must have adequate ventilation when the hood is
used at the same time as appliances operating on gas or
other fuels.
21. The discharge air must not be eliminated in a duct used to
remove fumes produced by appliances operating on gas or
other fuels, but must have a separate outlet. All the national
regulations on air discharge envisaged by art. 7.12.1 of CEI
EN 60335-2-31 must be observed.
22. If the hood is used together with other appliances operating
on gas or other fuels, the negative pressure in the room
must not exceed 4 Pa (4 x 10
-5
bar). Therefore, make sure
the room is adequately ventilated.
23. Do not leave pans unattended when frying, since the cooking
oil could catch fire.
24. Make sure the lamps are cold before touching them.
25. The hood is not a shelf, therefore do not overload or place
objects on it.
26. Do not use or leave the hood without its lamps correctly
installed - risk of electric shock.
27. Wear work gloves for all installation and maintenance
operations.
28. The product is not suitable for outdoor use.
29. The air sucked by the hood must not be eliminated through
the same flue of the heating system or other appliances using
gas or other fuels.
D F NL E
GB
PIGR
5019 318 33287
Electrical connection
The mains voltage must match that given on the rating plate
located inside the hood. If provided with a plug, connect the
hood to a socket complying with the current regulations and
located in an accessible area. If it does not have a plug (direct
connection to the power supply) or if the plug is not in an
accessible place, fit a suitable double-pole switch that ensures
complete disconnection from the power supply in category III
overvoltage conditions, complying with the installation rules.
WARNING: Before reconnecting the hood circuit to the
power supply and checking correct operation, always make sure
the power cable is correctly fitted and that it was NOT crushed
in its housing during installation. Make sure to have this operation
carried out by a specialised technician.
Cleaning the hood
WARNING! Failure to remove oil/grease (at least once a
month) could result in fire.
Use a soft cloth with a neutral detergent. Never use abrasive
substances or alcohol.
Before using the hood
Please read these instructions carefully and keep them for future
reference, in order to ensure best use of your hood.
The packing materials (plastic bags, polystyrene, etc.) are a
potential source of danger and must be kept out of the reach of
children.
Make sure the hood has not been damaged during transport.
Declaration of conformity
This product has been designed, manufactured and put on the
market in conformity with:
- safety objectives of the “Low Voltage” Directive 2006/95/EC
(which replaces 73/23/EEC as amended)
- protection requirements of “EMC” Directive 89/336/EEC
amended by Directive 93/68/EEC.
Troubleshooting guide
If the hood does not work:
Is the plug properly inserted in the power socket?
Is there a power failure?
If the hood is not extracting enough:
Is the right speed selected?
Do the filters need cleaning or replacing?
Are the air outlets blocked?
If the lamp does not work:
Does the lamp need replacing?
Is the lamp correctly fitted?
AFTER-SALES SERVICE
Before calling the After-Sales Service
1. Check to see if you can fix the problem yourself (see
“Troubleshooting Guide”).
2. Switch the appliance off and then on again to check if the
problem has been eliminated.
3. If the problem persists, contact the After-Sales Service.
Specify:
the type of fault,
the product model given on the dataplate inside the hood,
visible on removing the grease filters,
your full address,
your telephone number and area code,
the Service code (the number under the word SERVICE on
the dataplate inside the hood, behind the grease filter).
If any repairs are necessary, contact an authorised Service Centre
(to ensure the use of original spare parts and correct repair).
Failure to comply with these instructions can compromise the
safety and quality of the product.
D F NL E
GB
PIGR
5019 318 33287
Do not connect the appliance to the mains power supply until installation has been completed.
1. Mark a line on the wall, from the cooktop right up to the ceiling, corresponding to the centre-line of the hood.
2. Bearing in mind the minimum heights over the cooktop specified above, mark the height of the hood on the wall with a
pencil. Apply the drilling template to the wall over this mark.
3. Using the template supplied, mark the holes, drill them and insert the rawlplugs, then fit the 2 hooks (if provided) or partly
screw in 2 screws in the top holes.
4. Hang the hood and adjust the position with the hook adjustment screws (if supplied).
Note: The hood MUST be fixed with another 2 screws to be inserted in the bottom holes and (if provided for) with 2
screws in the top holes.
5. Only for some models: Mark the bottom (and top) holes, remove the hood, drill, insert the plugs
(partially screw 2 screws in the top holes).
6. Fix the flue support to the wall as close as possible to the ceiling. For the filter version, in this phase also fix the deflector F1
with 2 screws if the flue has grilles at the top (for flues with bottom grilles, see installation step “7”).
7. Hang the hood on the wall again and fix in place with the screws. For the filter version (flues with bottom grilles), the
deflector F2 must be fixed in place of the coupling ring (model with fixing with 2 screws) or fitted on the coupling ring
(model with 2 rear slots and 1 front fixing screw).
Extractor Version: Fumes are extracted and expelled to the outside through a fume hose fixed to the collar at the top of the
hood.
Important: If the hood is has a carbon filter fitted, the filter must be removed.
Filter Version: Air is filtered through a carbon filter and recycled into the surrounding environment.
Important: Caution! If the hood is not equipped with a carbon filter, one must be ordered and fitted before use.
Installing the electronic control box
If your hood has an electronic control box, S2 click it into its housing S1 and fix it in place with one screw.
On models with electronic control panels, fit the card S3 in the socket alongside the control box S2.
Telescopic flue installation
Connect the hood to the mains supply and fix the telescopic flue to the flue bracket with two screws. Slide the bottom
section down into its seat on the top of the hood. Fit the side grilles if provided.
* Only on some models
*
*
D F NL E
GB
PIGR
5019 318 33287
1. Control panel.
Light :
move the switch to the right or press the button to switch
on.
Extraction speed :
Move the switch to the right or press the next button to
increase extraction speed (or open the electric shutter ) .
2. Grease filters.
3. Lamp covers
(or halogen lamps, depending on the model).
4. Telescopic flue.
Grease filters:
Metal grease filters have an unlimited
life and should be washed once a
month either by hand or in a
dishwasher at a low temperature and
with a short cycle.
Note: Washing in a dishwasher can
cause grease filters to turn white, but
this in no way affects efficiency.
a. press the handle to remove the
filter
b. remove it.
Wash the filter and leave it to dry, proceeding in reverse
order to refit it.
Bulb/s:
Remove the filters and remove the burnt-out bulb.
Refit the filters.
Replacing the halogen bulbs:
1. Disconnect the hood from the mains power supply.
WARNING: Wear gloves.
2. Use a small screwdriver to gently prise the lamp cover off
(at the points indicated in Fig.).
3. Remove the burnt-out lamp and fit a new one.
WARNING: Replace using 20W max G4 halogen bulbs
only.
Close the lighting unit (snap-on).
Fitting or changing the carbon filter
(filter versions only).
Change the carbon filter every six months.
1. Remove the grease filters.
2. Fit the filter/s to cover the motor according to the model:
•Align the pins R on the cowl with the slots S, then
turn the filter clockwise until it locks in place
turn the central handle clockwise.
3. Reverse the above procedure to remove the carbon
filter.
4. Refit the grease filters.
Or
4
2
3
3
1
a
b
D F NL E
GB
PIGR
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Whirlpool AKR 029 IX User guide

Category
Cooker hoods
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI