HQ Power PAR36 User manual

VDPLPS3612x

PAR36 - 12 x 1W R+G+B LEDs - WITH BARN DOOR

PAR36 - 12 x 1W R+G+B LEDs - MET BARNDOOR

PAR36 - 12 LED DE 1W R+G+B AVEC COUPE-FLUX

FOCO LED PAR36 - 12 x 1W R+G+B CON 'BARN DOOR'

PAR36 LED-SCHEINWERFER -

12 x 1W R+G+B MIT 'BARN DOOR'

VDPLPS3612B

: black – zwart – noir –

color negro

VDPLPS3612W

: white

–

wit

–

blanc

–

blanco

USER MANUAL 3

GEBRUIKERSHANDLEIDING 7

NOTICE D’EMPLOI 11

MANUAL DEL USUARIO 15

BEDIENUNGSANLEITUNG 19

12 x 1W R+G+B MIT 'BARN DOOR'

color negro

– schwarz

blanco

-

weiß

VDPLPS3612x

03.03.2011

2

1

terminator

eindweerstand

résistance de

terminaison

terminación

Terminierung

How to turn the controller line from 3-pins into 5-pins (plug and socket).

Controller line van 3-pin naar 5-pin aanpassen (stekker en contact).

Modifier la ligne du contrôleur de 3 broches en 5 broches (fiche et contact).

Modificar la línea del controlador de 3 polos y 5 polos (conector y contacto).

Die Controller-Linie von 3-Pin nach 5-Pin anzupassen (Stecker und Kontakt).

©Velleman nv

terminator

eindweerstand

résistance de

terminaison

terminación

Terminierung

VDPLPS3612x

03.03.2011

3

USER MANUAL

1. Introduction

To all residents of the European Union

Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could

harm the environment.

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should

be taken to a specialized company for recycling.

This device should be returned to your distributor or to

a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing HQPower™!

Please read the manual thoroughly before bringing this device into service. If

the device was damaged in transit, don't install or use it and contact your dealer.

For more info concerning this product and the latest version of this manual, please visit our website

www.hqpower.eu.

2. Safety Instructions

Be very careful during the installation: touching live wires can cause life-

threatening electroshocks.

Always dis

connect mains power when device not in use or when servicing or maintenance activities

are performed. Handle the power cord by the plug only.

Keep this device away from children and unauthorized users.

Caution: device heats up during use.

Do not stare directly at the light source, as this may cause

- epileptic seizure in sensitive people

- temporarily loss of sight (flash blindness)

- permanent (irreversible) eye damage

There are no user-

serviceable parts inside the device. Refer to an authorized

spare parts.

•

This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified

person carry out the electric connection.

• Make sure that the available voltage does not exceed the

voltage stated in the specifications of this manual.

•

Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if

necessary.

• Respect a minimum distance of 0.5

m between the device’s light output and any illuminated sur

• Use an appropriate safety cable to fix the device (e.g. VDLSC7 or VDLSC8).

3. General Guidelines

Refer to the Velleman

®

Service and Quality Warranty

on the last pages of this manual.

Indoor use only.

Keep this device away form rain, moisture, splashing and dripping liquids.

Keep this device away from dust and extreme heat. Make sure the ventilation openings are clear

at all times. For sufficient air circulation, leave at least 1” (± 2.5

cm) in fr

Protect this device from shocks and abuse. Avoid brute force when operating the device.

•

Familiarise yourself with the functions of the device before actually using it. Do not allow operation by

unqualified people. Any damage that

may occur will most probably be due to unprofessional use of the

device.

•

All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the

device is not covered by the warranty.

• Only use the device for its intende

d purpose. All other uses may lead to short circuits, burns, electroshocks,

lamp explosion, crash, etc. Using the device in an unauthorised way will void the warranty.

•

Damage caused by disregard of certain guidelines in this manual is not covered by the wa

dealer will not accept responsibility for any ensuing defects or problems.

• A qualified technician should install and service this device.

©Velleman nv

This symbol on the device or the package indicates that disposal of the device after its lifecycle could

Do not dispose of the unit (or batteries) as unsorted municipal waste; it should

This device should be returned to your distributor or to

Please read the manual thoroughly before bringing this device into service. If

For more info concerning this product and the latest version of this manual, please visit our website

threatening electroshocks.

connect mains power when device not in use or when servicing or maintenance activities

serviceable parts inside the device. Refer to an authorized

dealer for service and/or

This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified

voltage stated in the specifications of this manual.

Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if

m between the device’s light output and any illuminated sur

face.

on the last pages of this manual.

Keep this device away form rain, moisture, splashing and dripping liquids.

Keep this device away from dust and extreme heat. Make sure the ventilation openings are clear

cm) in fr

ont of the openings.

Protect this device from shocks and abuse. Avoid brute force when operating the device.

Familiarise yourself with the functions of the device before actually using it. Do not allow operation by

may occur will most probably be due to unprofessional use of the

All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the

d purpose. All other uses may lead to short circuits, burns, electroshocks,

lamp explosion, crash, etc. Using the device in an unauthorised way will void the warranty.

Damage caused by disregard of certain guidelines in this manual is not covered by the wa

rranty and the

VDPLPS3612x

03.03.2011 ©Velleman nv

4

• Do not switch the device on immediately after it has been exposed to changes in temperature. Protect the

device against damage by leaving it switched off until it has reached room temperature.

• This device is designed for professional use on stage, in discos, theatres, etc. The VDPLPS3612x can be

used indoor (< 45°C, < 50%RH) with an alternating current of 230 VAC~50 Hz.

• Lighting effects are not designed for permanent operation: regular operation breaks will prolong their lives.

• Use the original packaging if the device is to be transported.

• Keep this manual for future reference.

4. Features

• pinspot with 12x1W superbright LEDs, with barndoor

• very long lifetime thanks to LED technology

• DMX-controlled (via 5 channels) or stand-alone mode

• digital menu

5. Overview

Refer to the illustrations on page 2 of this manual.

1 display with control buttons 2

DMX output

A

MODE button 3

DMX input

B

UP button 4

fuse

C

DOWN button 5

power input

6. Installation

a) Overhead mounting

Risk of injury. Overhead mounting requires extensive experience: calculating workload limits,

determining the installation material to be used… Have the material and the device itself checked

regularly. Do not attempt to install the device yourself if you lack these qualifications as improper

installation may result in injuries.

• Have the device installed by a qualified person, respecting EN 60598-2-17 and all other applicable norms.

• The construction to which the device is attached should be able to support 10 times the weight of the

device for one hour without deformation.

• The installation must always be secured with a secondary attachment e.g. a safety cable.

• Never stand directly below the device when it is being mounted, removed or serviced. Have a qualified

technician check the device once a year and once before you bring it into service.

• Install the device in a location with few passers-by and inaccessible to unauthorised persons.

• For truss-mounting, use an appropriate clamp (not incl.) and fit an M10 bolt through the centre of the

(folded) bracket.

• Adjust the desired inclination angle via the mounting bracket and tighten the bracket screws.

b) DMX-512 connection

• When applicable, connect an XLR cable to the female 3-pin XLR output of a controller (not incl.) and the

other side to the male 3-pin XLR input of the VDPLPS3612x. Multiple VDPLPS3612x’s can be linked

through serial linking. The linking cable should be a dual core, screened cable with XLR input and output

connectors.

• Maximum recommended serial data link distance is 500 meters (1640 ft). Maximum recommended number

of fixtures on a serial data link is 32 fixtures.

• A DMX terminator is recommended for installations where the DMX cable has to run a long distance or is in

an electrically noisy environment (e.g. discos). The terminator prevents corruption of the digital control

signal by electrical noise. The DMX terminator is simply an XLR plug with a 120Ω resistor between pins 2

and 3, which is then plugged into the XLR output socket of the last device in the chain.

c) general

• Make sure there is no flammable material within a 50cm radius of the device and there is sufficient cooling.

• Have a qualified electrician carry out the electrical connection.

• Connect the device to the mains with the power plug. All fixtures must be powered directly off a grounded

switched circuit and cannot be run off a rheostat or dimmer circuit, even if the rheostat or dimmer channel

is used solely for 0% to 100% switch.

• The installation has to be approved by an expert before the device is taken into service.

VDPLPS3612x

03.03.2011

5

7. Operation

• Set the desired mode using the mode button [1A]

. The mode is indicated in the display (refer to the table

below).

• Change the setting with the UP [1B] or DOWN [1C] buttons.

display mode setting from

DMX see table below -

sound controlled sensitivity

max.

red (R)

brightness

off

green (G)

blue (B)

R + G

R + B

B + G

R + G + B

black out all LEDs off -

R +G + B flash

speed

fast

7 colour change

7 colour flash

7 colour fade

DMX address

• When using DMX mode ( ), first set the DMX address.

• All DMX-

controlled devices need a digital start address so that the correct device responds to the signals.

This digital start address is the channel number from which the device starts to “listen” to the DMX

controller. The same starting address

can be used for a whole group of devices or an individual address can

be set for every device.

•

When all devices have the same address, all the units will “listen” to the control signal on one particular

channel. In other words: changing the settings of one

channel will affect all devices simultaneously. If you

set individual addresses, each device will “listen” to a separate channel number. Changing the settings of one

channel will only affect the device in question.

• In case of the 5-channel VDPLPS3612X, you will have to set the start addre

ss of the first unit to 1

(CH1~5), the second unit to 6 (1 + 5) (CH6~10), the third to 11 (6 + 5) (CH

11~1

DMX mode ( )

CH1

(mode)

function

CH2

(speed)

CH3

(red)

CH4

(green)

000 ~ 025

Black out - - -

026 ~ 050

R, G, B

000 ~ 255

dimmer

000 ~ 255

051 ~ 100

flash

000 ~ 255

slow ~ fast

000 ~ 255

brightness

000 ~ 255

brightness

101 ~ 150

7 colour change

000 ~ 255

slow ~ fast

- -

151 ~ 200

7 colour fade

000 ~ 255

slow ~ fast

- -

201 ~ 240

sound controlled

000 ~ 255

slow ~ fast

- -

241 ~ 255 full R, G, B - - -

• To use slave mode, first connect the devices as described in §6b.

• On all slave devices set the mode to .

©Velleman nv

. The mode is indicated in the display (refer to the table

to

-

max.

min.

max.

-

fast

slow

controlled devices need a digital start address so that the correct device responds to the signals.

This digital start address is the channel number from which the device starts to “listen” to the DMX

can be used for a whole group of devices or an individual address can

When all devices have the same address, all the units will “listen” to the control signal on one particular

channel will affect all devices simultaneously. If you

set individual addresses, each device will “listen” to a separate channel number. Changing the settings of one

ss of the first unit to 1

11~1

5), and so on.

CH4

(green)

CH5

(blue)

-

000 ~ 255

brightness

000 ~ 255

brightness

-

VDPLPS3612x

03.03.2011 ©Velleman nv

6

8. Cleaning and maintenance

•

This unit does not need regular maintenance. The internal circuit is protected by a 250V/500mA, 5 x 20 mm

fuse [4]. Replace a faulty fuse by a fuse of the exact specifications.

•

All screws should be tight and free of corrosion.

•

The housing, the lenses, the mounting supports and the installation location (e.g. ceiling, suspension,

trussing) should not be deformed, modified or tampered with e.g. do not drill extra holes in mounting

supports, do not change the location of the connections …

•

Mechanically moving parts must not show any signs of wear and tear.

•

The electric power supply cables must not show any damage. Have a qualified technician maintain the

device.

• Regularly remove dust from the housing and the air vents using a slightly damp cloth.

• There are no user-serviceable parts inside. Refer to an authorized dealer for service and/or spare parts.

9. Technical Specifications

power supply 230VAC ~ 50Hz

power consumption 12W

number of LEDs 12 x 1W RGB (4xR, 4xG, 4xB )

DMX channels 5

dimensions 160 x 115 x 115mm

weight 1.4kg

Use this device with original accessories only. Velleman nv cannot be held responsible in the event of

damage or injury resulted from (incorrect) use of this device. For more info concerning this product

and the latest version of this manual, please visit our website www.hqpower.eu. The information in

this manual is subject to change without prior notice.

The copyright to this manual is owned by Velleman nv. All worldwide rights reserved.

No part of this manual or may be copied, reproduced, translated or reduced to any electronic medium or

otherwise without the prior written consent of the copyright holder.

Page is loading ...

Velleman® Service and Quality Warranty

Velleman® has over 35 years of experience in the electronics world

and distributes its products in more than 85 countries.

All our products fulfil strict quality requirements and legal

stipulations in the EU. In order to ensure the quality, our products

regularly go through an extra quality check, both by an internal

quality department and by specialized external organisations. If, all

precautionary measures notwithstanding, problems should occur,

please make appeal to our warranty (see guarantee conditions).

General Warranty Conditions Concerning Consumer Products

(for EU):

• All consumer products are subject to a 24-month warranty on

production flaws and defective material as from the original date of

purchase.

• Velleman® can decide to replace an article with an equivalent

article, or to refund the retail value totally or partially when the

complaint is valid and a free repair or replacement of the article is

impossible, or if the expenses are out of proportion.

You will be delivered a replacing article or a refund at the value of

100% of the purchase price in case of a flaw occurred in the first

year after the date of purchase and delivery, or a replacing article at

50% of the purchase price or a refund at the value of 50% of the

retail value in case of a flaw occurred in the second year after the

date of purchase and delivery.

• Not covered by warranty:

- all direct or indirect damage caused after delivery to the article

(e.g. by oxidation, shocks, falls, dust, dirt, humidity...), and by the

article, as well as its contents (e.g. data loss), compensation for loss

of profits;

- frequently replaced consumable goods, parts or accessories such as

batteries, lamps, rubber parts, drive belts... (unlimited list);

- flaws resulting from fire, water damage, lightning, accident, natural

disaster, etc. …;

- flaws caused deliberately, negligently or resulting from improper

handling, negligent maintenance, abusive use or use contrary to the

manufacturer’s instructions;

- damage caused by a commercial, professional or collective use of

the article (the warranty validity will be reduced to six (6) months

when the article is used professionally);

- damage resulting from an inappropriate packing and shipping of

the article;

- all damage caused by modification, repair or alteration performed

by a third party without written permission by Velleman®.

• Articles to be repaired must be delivered to your Velleman®

dealer, solidly packed (preferably in the original packaging), and be

completed with the original receipt of purchase and a clear flaw

description.

• Hint: In order to save on cost and time, please reread the manual

and check if the flaw is caused by obvious causes prior to presenting

the article for repair. Note that returning a non-defective article can

also involve handling costs.

• Repairs occurring after warranty expiration are subject to shipping

costs.

• The above conditions are without prejudice to all commercial

warranties.

The above enumeration is subject to modification according

to the article (see article’s manual).

Velleman® service- en kwaliteitsgarantie

Velleman® heeft ruim 35 jaar ervaring in de elektronicawereld en

verdeelt in meer dan 85 landen.

Al onze producten beantwoorden aan strikte kwaliteitseisen en aan

de wettelijke bepalingen geldig in de EU. Om de kwaliteit te

waarborgen,

ondergaan onze producten op regelmatige tijdstippen een extra

kwaliteitscontrole, zowel door onze eigen kwaliteitsafdeling als door

externe gespecialiseerde organisaties. Mocht er ondanks deze

voorzorgen toch een probleem optreden, dan kunt u steeds een

beroep doen op onze waarborg (zie waarborgvoorwaarden).

Algemene waarborgvoorwaarden consumentengoederen

(voor Europese Unie):

• Op alle consumentengoederen geldt een garantieperiode van 24

maanden op productie- en materiaalfouten en dit vanaf de

oorspronkelijke aankoopdatum.

• Indien de klacht gegrond is en een gratis reparatie of vervanging

van een artikel onmogelijk is of indien de kosten hiervoor buiten

verhouding zijn, kan Velleman® beslissen het desbetreffende artikel

te vervangen door een gelijkwaardig artikel of de aankoopsom van

het artikel gedeeltelijk of volledig terug te betalen. In dat geval krijgt

u een vervangend product of terugbetaling ter waarde van 100% van

de aankoopsom bij ontdekking van een gebrek tot één jaar na

aankoop en levering, of een vervangend product tegen 50% van de

kostprijs of terugbetaling van 50 % bij ontdekking na één jaar tot 2

jaar.

• Valt niet onder waarborg:

- alle rechtstreekse of onrechtstreekse schade na de levering

veroorzaakt aan het toestel (bv. door oxidatie, schokken, val, stof,

vuil, vocht...), en door het toestel, alsook zijn inhoud (bv. verlies van

data), vergoeding voor eventuele winstderving.

- verbruiksgoederen, onderdelen of hulpstukken die regelmatig

dienen te worden vervangen, zoals bv. batterijen, lampen, rubberen

onderdelen, aandrijfriemen... (onbeperkte lijst).

- defecten ten gevolge van brand, waterschade, bliksem, ongevallen,

natuurrampen, enz.

- defecten veroorzaakt door opzet, nalatigheid of door een

onoordeelkundige behandeling, slecht onderhoud of abnormaal

gebruik of gebruik van het toestel strijdig met de voorschriften van

de fabrikant.

- schade ten gevolge van een commercieel, professioneel of collectief

gebruik van het apparaat (bij professioneel gebruik wordt de

garantieperiode herleid tot 6 maand).

- schade veroorzaakt door onvoldoende bescherming bij transport

van het apparaat.

- alle schade door wijzigingen, reparaties of modificaties uitgevoerd

door derden zonder toestemming van Velleman®.

• Toestellen dienen ter reparatie aangeboden te worden bij uw

Velleman®-verdeler. Het toestel dient vergezeld te zijn van het

oorspronkelijke aankoopbewijs. Zorg voor een degelijke verpakking

(bij voorkeur de originele verpakking) en voeg een duidelijke

foutomschrijving bij.

• Tip: alvorens het toestel voor reparatie aan te bieden, kijk nog

eens na of er geen voor de hand liggende reden is waarom het

toestel niet naar behoren werkt (zie handleiding). Op deze wijze kunt

u kosten en tijd besparen. Denk eraan dat er ook voor niet-defecte

toestellen een kost voor controle aangerekend kan worden.

• Bij reparaties buiten de waarborgperiode zullen transportkosten

aangerekend worden.

• Elke commerciële garantie laat deze rechten onverminderd.

Bovenstaande opsomming kan eventueel aangepast worden

naargelang de aard van het product (zie handleiding van het

betreffende product).

Garantie de service et de qualité Velleman®

Velleman® jouit d’une expérience de plus de 35 ans dans le monde

de l’électronique avec une distribution dans plus de 85 pays.

Tous nos produits répondent à des exigences de qualité rigoureuses

et à des dispositions légales en vigueur dans l’UE. Afin de garantir la

qualité, nous soumettons régulièrement nos produits à des contrôles

de qualité supplémentaires, tant par notre propre service qualité que

par un service qualité externe. Dans le cas improbable d’un défaut

malgré toutes les précautions, il est possible d’invoquer notre

garantie (voir les conditions de garantie).

Conditions générales concernant la garantie sur les produits

grand public (pour l’UE) :

• tout produit grand public est garanti 24 mois contre tout vice de

production ou de matériaux à dater du jour d’acquisition effective ;

• si la plainte est justifiée et que la réparation ou le remplacement

d’un article est jugé impossible, ou lorsque les coûts s’avèrent

disproportionnés, Velleman® s’autorise à remplacer ledit article par

un article équivalent ou à rembourser la totalité ou une partie du prix

d’achat. Le cas échéant, il vous sera consenti un article de

remplacement ou le remboursement complet du prix d’achat lors

d’un défaut dans un délai de 1 an après l’achat et la livraison, ou un

article de remplacement moyennant 50% du prix d’achat ou le

remboursement de 50% du prix d’achat lors d’un défaut après 1 à 2

ans.

• sont par conséquent exclus :

- tout dommage direct ou indirect survenu à l’article après livraison

(p.ex. dommage lié à l’oxydation, choc, chute, poussière, sable,

impureté…) et provoqué par l’appareil, ainsi que son contenu (p.ex.

perte de données) et une indemnisation éventuelle pour perte de

revenus ;

- tout bien de consommation ou accessoire, ou pièce qui nécessite un

remplacement régulier comme p.ex. piles, ampoules, pièces en

caoutchouc, courroies… (liste illimitée) ;

- tout dommage qui résulte d’un incendie, de la foudre, d’un

accident, d’une catastrophe naturelle, etc. ;

- out dommage provoqué par une négligence, volontaire ou non, une

utilisation ou un entretien incorrects, ou une utilisation de l’appareil

contraire aux prescriptions du fabricant ;

- tout dommage à cause d’une utilisation commerciale,

professionnelle ou collective de l’appareil (la période de garantie sera

réduite à 6 mois lors d’une utilisation professionnelle) ;

Page is loading ...

HQ Power PAR36 User manual

HQ Power PAR36 User manual

in other languages

Related papers

Other documents