Apevia X-Dreamer II ATXB4KLW Series Installation guide

Brand: Apevia

Model: X-Dreamer II ATXB4KLW Series

Category: Computer cases

Type: Installation guide

ATXB4KLW(X-Dreamer II) Series Installation Guide

1:Unscrew the thumb screws 2.Pull the side panel back then 3:Find the motherboard stand-offs

from side panel. pull out. from the enclosed screw box.

4:Put the motherboard stand-offs 5.Sit the motherboard on the 6.Find screws in the screw box.

on the motherboard tray. motherboard tray.

7.Screw in all the screws into the 8.Same as Step 7.

motherboard stand-offs

9.Take out front panel:

Step (1): Unscrew the side Step (2): Take out the side Step (3): There are 4 screws that

panel (motherboard side) panel (motherboard side) hold the front panel to the case. (2

on each side) Unscrew the 2 screws

from inside of the case.

Step (4): Unscrew the other Step (5): Pull out the front panel

2 screws from the other side. from the bottom.

10.Optional:Install case fan in 11.Optional: Install case fan 12.Take out the metal plate and

the front panel (You can put up at rear (1*80mm-120mm fan) install 5.25” drives(DVD, CD-RW,

to 2*80mm fans in the front.) CD-ROM)

13.Secure the 5.25” drives 14.Slide in 3.5” FDD Drive and 15.Install 3.5” hidden drives such

in place with screws. secure with screws. as hard drive, zip drive.

16.Screw all 3.5” hidden drives 17.Snap in the front panel and 18.Audio Cable: Take out the I/O slot

in place with screws. screw the front panel to the case. with a hole from the back of the case

.

19.Find the audio cables and 20.Put the I/O slot back. Fit the 21.Plug audio cables into

bring them through the I/O slot knot into the hold and screw I/O sound card or M/B.

to outside of the back panel. slot back.

22.Find the 4pin connectors 23.Find the 20-pin connector 24.Plug into your motherboard.

(Female and Male) from case from power supply. Different M/B has different layout.

Fan. Connect the Male to the Please refer to your motherboard

Female 4pin from power supply. user manual.

25.Find the 4-pin P4 connector 26.Plug into your motherboard. 27.Find 2*USB Cables.

from power supply.(for P4 only) (For Intel P4 motherboard only) (USB1 & USB2)

28.Plug USB cables to your M/B. 29.Find “HDD LED” and 30.Plug them onto your M/B.

Please refer to M/B user manual. “Reset SW” cables. Please refer to M/B user manual.

31.Find “Power SW”, “+P LED” 33.Find “Case Speaker” from 34.Install case speaker to M/B

& “-P LED” cables and plug onto screw box. following M/B user manual

M/B. Please refer to M/B user

manual.

35.Install LED Lights: Find 2*LED 36.Connect the 4-pin Male connector

connectors from the front panel. to a 4-pin Female connector from

They are 2*2-pin connectors that power supply.

lead to 2*4-pin connectors

(1*Male, 1*Female)

37.LCD Temperature Readout: 38.Remove the protective plastic 39.This is the temperature

Connect 4-pin Male connector from tube from the sensor. Sensor. It’s very fragile.

LCD to a 4-pin Female connector Be gentle.

from power

supply.

40.You can either tape the sensor on Hard Drive or on CPU Heat 41.This is how the case front panel

sink or leave it inside the case to get the overall system temperature. looks like after powered on.

42.Find “Case Feet” in screw box. Lay

case down and put “Case Feet” on.

Note:

1.You can link together all the 4-pin connectors(male to female) from all the case fans, LCD, LED, HDD and just

use one of the 4-pin Molex connectors from power supply. That will leave you more 4-pin connectors from your

power supply for other devices.

1
2
3
4
5
6

Apevia X-Dreamer II ATXB4KLW Series Installation guide

Brand: Apevia

Model: X-Dreamer II ATXB4KLW Series

Category: Computer cases

Type: Installation guide

Download PDF

Related papers

Other documents