Hunter Fan 59051 Owner's manual

Type
Owner's manual

Hunter Fan 59051 is a state-of-the-art device that combines advanced technology with sleek design to provide unparalleled comfort and style to your home or office. With its powerful motor and aerodynamic blades, it effectively circulates air, ensuring a constant flow of fresh air throughout the space. The fan's adjustable settings allow you to customize the airflow intensity to suit your needs, whether you prefer a gentle breeze or a refreshing gust.

Hunter Fan 59051 is a state-of-the-art device that combines advanced technology with sleek design to provide unparalleled comfort and style to your home or office. With its powerful motor and aerodynamic blades, it effectively circulates air, ensuring a constant flow of fresh air throughout the space. The fan's adjustable settings allow you to customize the airflow intensity to suit your needs, whether you prefer a gentle breeze or a refreshing gust.

www.HunterFan.com
1.866.268.1936
PAGE
14
Light Kit
PAGE
13
Blades
Table of Contents
Operation,
Maintenance & Cleaning
PAGE
18
Troubleshooting
?
?
?
PAGE
20
PAGE
5
Ceiling Bracket
PAGE
4
Mounting Options
30 inches
7 feet
PAGE
2
What to Expect with
Your Installation
Ladder
PAGE
3
Tools Needed
Congratulations on purchasing
your new Hunter® ceiling fan! It will
provide comfort and performance
in your home or ofce for many
years. This installation and operation
manual contains complete
instructions for installing and
operating your fan.
We are proud of our work and
appreciate the opportunity to
supply you with the best ceiling fan
available anywhere in the world.
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
Remote Control
PAGE
17
PAGE
7
Downrod
Canopy
PAGE
12
PAGE
11
Wiring
PAGE
6
Assembling the Top
Housing
PAGE
10
Secondary Hanging
System
1
M3538-01 • 05/15/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
M3538-01 • 05/15/14 • © Hunter Fan Company
What to Expect with Your Installation
Know your wiring
If you are unfamiliar
with wiring, use a
qualied electrician.
You may need a
friend to help you.
Check box to see
fan weight
Assess location
30 inches
from blade tip
to nearest wall
or obstruction
7 feet
from bottom
edge of blade
to the oor
Assess ceiling angle
Must be able to
secure the fan to
building structure or
fan-rated outlet box
2
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
CAUTIONS
w.1 - To reduce the risk of re, electrical shock, or personal
injury, mount fan directly from building structure and/or an
outlet box marked acceptable for fan support of 70 lbs (31.8 kg)
and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or
servicing your fan, disconnect the power by turning off the
circuit breakers to the outlet box and associated wall switch
location. If you cannot lock the circuit breakers in the off
position, securely fasten a prominent warning device, such as a
tag, to the service panel.
w.3 - To reduce the risk of re, electrical shock, or motor damage,
use only Hunter Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade
brackets when installing the blade brackets, balancing the blades,
or cleaning the fan. Do not insert foreign objects in between
rotating fan blades.
c.1 - All wiring must be in accordance with national and local
electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring,
use a qualied electrician.
c.2 - Use only Hunter replacement parts.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not
installed and used in accordance with the instructions may cause
harmful interference to radio communications.
Select a downrod length
1
2
3
Standard Downrod
for ceilings 8-10 feet high
Shorter Downrod
for fans installed close to ceiling
Longer Downrod
for ceilings 10 feet or higher
www.HunterFan.com
1.866.268.1936
Tools Needed
Ladder
Power Drill
(optional)
9/64” Drill Bit
(optional)
Screwdrivers
Pliers Wire Strippers
If mounting to a support structure, you will also need these tools.
3
M3538-01 • 05/15/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
4
M3538-01 • 05/15/14 • © Hunter Fan Company
1.866.268.1936
If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Guide Touches
BOTH Ceiling & Wall
S
I
T
U
A
T
I
O
N
1
Guide Touches
Wall
but
NOT Ceiling
S
I
T
U
A
T
I
O
N
2
You need BOTH
a Longer
Downrod &
an Angled
Mounting Kit
You need ONLY
a Longer
Downrod
*most common
If you have a at ceiling:
Hang your fan by a standard downrod (included).
Mounting Options
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
4
34
O
CEILING
WALL
OPTION
1
Standard
Mounting
OPTION
2
Angled
Mounting
2 3
SLIDE
toward ceiling
PLACE
against wall
1
FOLD
on dotted line
34°
Use the three steps below to determine if your ceiling angle is greater than 34°
Support
Structure
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
Standard
Mounting
Style
Support
Structure
Ceiling
Outlet Box
(required)
M3538-01 • 05/15/14 • © Hunter Fan Company
Use Standard Mounting
or Low-Prole Mounting
to hang the fan from a at ceiling.
www.HunterFan.com
www.HunterFan.com
1.866.268.1936
Ceiling Bracket
5
OFF
For angled ceilings, point
opening toward peak.
Refer to warning w.1 on pg. 2
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Use wood screws
(included) when securing
to support structure with
approved electrical outlet
box. Drill 9/64” pilot holes
in support structure to aid
in securing ceiling bracket
with hardware found in
the hardware bag.
Use machine screws
(provided with outlet
box) when securing to
existing ceiling fan-rated
outlet box. Make sure
it is securely installed
and is acceptable for fan
support of 31.8 kg (70 lbs)
or less.
Turn Power
Make sure all four (4)
bumpers are still attached.
To avoid possible electrical shock, before installing your fan,
disconnect the power by turning off the circuit breakers to
the outlet box associated with the wall switch location.
5
M3538-01 • 05/15/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Assembling the Top Housing
KEEP!
Remove the pre-installed
setscrew so that the downrod
can be inserted.
K
E
E
P
!
Install three upper motor cover
screws, found in the hardware
bag, and tighten them securely.
Upper Motor
Cover Screw
To assemble the housing to the
hanger adapter, align the three
raised tabs on the hanger adapter
with the three narrow notches in
the top housing. Make certain the
housing sits at on the adapter.
6
M3538-01 • 05/15/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
7
M3538-01 • 05/15/14 • © Hunter Fan Company
Downrod
Slide
Slide
1 2 3 4 5
678910
skip to next page
If you need a different downrod length follow these steps:
Steps 1-5 to remove standard downrod pipe
Steps 6-10 to reassemble with new pipe
www.HunterFan.com
Sold Separately
Longer
Downrod
for angled
ceilings or
ceilings 10’ or
higher
Standard
Downrod
for ceilings 8-10’ high
Option 1
Included
Shorter
Downrod
for fans installed
close to ceiling
Option 2
Option 3
Included
(pre-assembled)
www.HunterFan.com
1.866.268.1936
Downrod (continued)
8”
3/8”
If the setscrew is not tightened
securely, the fan may fall.
1.866.268.1936
www.HunterFan.com
8”
3/8”
C
U
T
&
S
T
R
I
P
(not to scale)
The wires can be cut, but leave at least 8”
extending from the top of the downrod.
Tighten the setscrew with pliers.
DO NOT HAND TIGHTEN.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8
M3538-01 • 05/15/14 • © Hunter Fan Company
8
1.866.268.1936
9
M3538-01 • 05/15/14 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
www.HunterFan.com
1.866.268.1936
10
M3538-01 • 05/15/14 • © Hunter Fan Company
Secondary Hanging System
3mm (1/8")
Insert the looped end of the
braided cable through the ceiling
bracket and one of the holes in the
outlet box into the ceiling. Access
the support brace in the ceiling.
You may not be able to do this from
below the ceiling depending on
your installation site.
Drive the wood screw and
washer found in the bag
into the side of the support
brace that holds the outlet box.
Leave 3 mm (1/8”) of space
between the support brace
and the washer.
Wrap the braided cable around
the support brace once creating
a complete circle. Hook the
looped end of the cable over the
wood screw so that the cable
lies between the washer and the
support brace.
Tighten the loop and secure the
screw and washer all the way
down to the support brace. Coil
up the excess cable.
Outlet Box
Ceiling
Support
Brace
Braided
Cable
www.HunterFan.com
1.866.268.1936
Wiring
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
11
M3538-01 • 05/15/14 • © Hunter Fan Company
Using an orange wire
connector from
the hardware
bag, connect the
3 grounding wires
(green, green/yellow
stripe, or bare copper)
coming from the
ceiling, downrod, and
hanging bracket.
F
R
O
M
R
E
C
E
I
V
E
R
F
R
O
M
C
E
I
L
I
N
G
F
R
O
M
C
E
I
L
I
N
G
B
R
A
C
K
E
T
green/yellow
stripe (grounding)
green/yellow
stripe
green/yellow stripe
black
blue
yellow
blue
Note: To connect the
wires, hold the bare
metal leads together and
place a wire connector
over them, then twist
clockwise until tight.
Using the orange
wire connectors
from the remote
control hardware
bag, connect the blue
wire from the receiver
to the blue wire (or
possibly black with
white stripe wire) from
the fan. Connect the
yellow wire from the
receiver to the black
wire from the fan.
F
R
O
M
F
A
N
F
R
O
M
F
A
N
F
R
O
M
R
E
C
E
I
V
E
R
Using the orange wire
connectors from
the hardware bag,
connect the black wire
(ungrounded) from
the ceiling to the black
wire from the receiver.
Connect the white
wire (grounded) from
the ceiling to both the
white wire from the
receiver and the white
wire from the fan.
F
R
O
M
C
E
I
L
I
N
G
black
(ungrounded)
white (grounded)
black
white
F
R
O
M
F
A
N
white
www.HunterFan.com
1.866.268.1936
12
M3538-01 • 05/15/14 • © Hunter Fan Company
Canopy
Lift the canopy into place so that
the screw holes are aligned.
Position the canopy so that, when
lifted into place, the canopy ts into
the hanging bracket as shown.
Insert the two canopy screws
found in the hardware bag.
Note: Fan style may vary.
Screw
Holes
www.HunterFan.com
1.866.268.1936
Blades
Your blades are shielded with Dust Armor® which
is a nanotechnology coating that repels dust. For
cleaning the fan, use soft brushes or cloths to prevent
scratching. Cleaning agents may damage the nishes.
Attach the blade to the motor using the at
washers from the hardware bag and blade
assembly screws found in the hardware bag.
Repeat for each blade.
Insert the blade into the slot. Align the holes on
the blade with the holes in the fan motor.
Holes
13
M3538-01 • 05/15/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
Light Kit
Align the keyholes in the light kit with the
two partially installed screws and turn the
light kit clockwise until the screws are in
the narrow ends of the keyholes.
Thread the 9-pin plug connector from the
fan through the light kit.
Attachment Screw
Partially install two attachment
screws, found in the hardware
bag, into the light kit mounting plate.
14
M3538-01 • 05/15/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
15
M3538-01 • 05/15/14 • © Hunter Fan Company
Light Kit (continued)
Make sure the light kit is securely attached to the mounting
plate. Failure to properly secure all three assembly screws
could result in the light xture falling.
Connect the upper 9-pin plug
connector from the fan to the
lower 9-pin plug connector in the
light kit.
Align the two screw screw holes
and install the switch housing
assembly screws, found in the
hardware bag.
Install the remaining attachment
screw to secure the light kit to
the mounting plate. Securely
tighten all three screws.
Attachment Screw
Install the included 22 Watt
uorescent bulb into the hooks
on the tter.
www.HunterFan.com
1.866.268.1936
16
M3538-01 • 05/15/14 • © Hunter Fan Company
Light Kit (continued)
Connect the 4 pin plug from the ballast to
the uorescent bulb.
4 Pin Plug
CONGRATULATIONS!
YOU’RE DONE!
See next page for fan
operation instructions.
Glass Globe
Trim Ring
Globe
Assembly
Screw
Place the glass globe into the globe trim
ring. Align the three holes in the trim
ring with the three holes in the light
kit. Install and securely tighten all three
globe assembly screws, found in the
hardware bag.
Note: In compliance with Canadian federal
energy regulations, this ceiling fan contains a
device that restricts its light output. Exceeding
the wattage limit marked on the MAX wattage
sticker afxed to the light socket(s) may result
in re hazard or improper operation.
www.HunterFan.com
1.866.268.1936
Remote Control
Note: The remote must be paired before
the fan will operate.
Within 3 minutes of restoring power to
the fan, press both the Fan Off button and
the High button for at least 4 seconds. Your
fan will turn on low to indicate successful
syncing. If it does not, turn off power to your
fan, wait 1 minute then try again. If using the
transmitter with multiple fans, repeat this
process for each fan.
Fan Off
High
To access the battery compartment, remove
the small Phillips head screw that secures the
battery door to the transmitter assembly. The
battery should be installed with the positive
(+) side up. Replace with a CR2032 battery
when necessary.
Phillips
Head
Screw
Battery
Door
ON
Turn Power
If you are installing multiple remote-controlled fans on
the same circuit breaker, you may need to perform a few
extra steps to prevent interference or faulty operation of
your remote controls.
Go to www.HunterFan.com/FAQs and click
“How do I properly install multiple remote-controlled fans?”
for more information.
17
M3538-01 • 05/15/14 • © Hunter Fan Company
17
www.HunterFan.com
1.866.268.1936
Rocker- Style
Plate
Switch Cover Plate
Removed
Tabs
To install the transmitter cradle, remove the
two screws holding the switch cover plate. Do
not remove the cover plate. Orient the cradle
by lining up the two mounting holes with
those on the cover plate. Insert and tighten
the screws. Do not over tighten.
Note: For rocker-style cover plates, break off
the tabs by pushing outward.
To turn on fan, press a fan speed button.
Speeds range from off (0) to high (3). Quickly
press the Light button to turn the lights off
and on. Hold the Light button to raise and
dim the light level.
Medium
Speed
Light
High
Speed
Fan
Off
Low
Speed
Operation, Maintenance, & Cleaning
To switch the direction of air ow, remove
the globe on the fan by removing the globe
assembly screws, the glass, and trim ring. Flip
the black switch to change the direction.
Reverse
Switch
18
M3538-01 • 05/15/14 • © Hunter Fan Company
www.HunterFan.com
1.866.268.1936
19
M3538-01 • 05/15/14 • © Hunter Fan Company
Operation, Maintenance, & Cleaning (continued)
When cleaning the fan, use soft brushes or cloths
to prevent scratching. Cleaning products may
damage the nishes.
Safe-Exit
Press the Fan Off button for at least three
seconds to initiate the Safe-Exit Mode.
The lights will ash for visual conrmation.
The lights will stay on 50% brightness for 15
seconds and then begin to dim. After a total
of 30 seconds, the lights will be completely
off.
The Safe-Exit Program gives you about
thirty seconds of light when you turn the
lights off to exit the room before the lights
go out. To use Safe-Exit:
Note: For CFL lighting, the lights will stay on
100% brightness for 30 seconds. After a total
of 30 seconds, the lights will be completely
off.
Hunter fans have the power to cut your cooling costs up
to 40%.
Beat the High Cost of Cooling
The air movement created by a Hunter ceiling fan
lets you set your thermostat higher and still stay
comfortable. Every degree you raise the thermostat
saves up to 7% on energy costs. So, you can cut back on
expensive air conditioning ... and save up to 40%* on
cooling. In winter, your Hunter fan recirculates warm air
and saves up to 10%* on heating bills.
* On average at low speed settings. Your savings may
vary based on climate, building type and thermostat
setting.
Save Energy and Money While Protecting
the Environment
Congratulations! You’re saving energy and money while
protecting the environment by purchasing this ENERGY
STAR qualied Hunter ceiling fan! With this purchase, you
are doing your part to protect the environment.
Your new ceiling fan has earned the ENERGY STAR label
because it meets high energy efciency specications
set by the Environmental Protection Agency (EPA).
ENERGY STAR labeled ceiling fans save energy because
they have more efcient fan motors and air delivery due
to more aerodynamic blade congurations. Ceiling fan
models bearing the ENERGY STAR label move air 14 -
20% more efciently than typical ceiling fan models.
For more information on ENERGY STAR visit
www.energystar.gov.
www.HunterFan.com
1.866.268.1936
20
Troubleshooting
Excessive wobbling
Tighten all of the blade and
blade iron screws until they
are snug.
Use the provided balancing
kit and instructions to balance
the fan.
Noisy Operation
Tighten the blade and blade
iron screws until they are snug.
Check to see if any of the
blades are cracked. If so, replace
all of the blades.
Fan doesn’t work
Make sure power switch is on.
Push the motor reversing switch
rmly left or right to ensure that
it is engaged.
Check the circuit breaker to
ensure the power is turned on.
Make sure the blades spin freely.
Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 11.
Check the plug connection in
the switch housing.
Remote control of fan is erratic
Make sure the battery is
installed correctly.
Install a fresh battery.
Transmitter only works when
held at close range
Install a fresh battery.
If you have multiple remotes or
multiple remote-controlled fans
installed on the same circuit
breaker and you are experiencing
interference or faulty operation of
your remote controls, please go to
www.HunterFan.com/FAQs
and click “How do I properly install
multiple remote-controlled fans?”
for information on how to correct
this issue.
20
M3538-01 • 05/15/14 • © Hunter Fan Company
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Hunter Fan 59051 Owner's manual

Type
Owner's manual

Hunter Fan 59051 is a state-of-the-art device that combines advanced technology with sleek design to provide unparalleled comfort and style to your home or office. With its powerful motor and aerodynamic blades, it effectively circulates air, ensuring a constant flow of fresh air throughout the space. The fan's adjustable settings allow you to customize the airflow intensity to suit your needs, whether you prefer a gentle breeze or a refreshing gust.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI