Summit SWC1966B User manual

WINE CELLAR

Models:

SWC1127B

SWCP2116

SWC1926B

SWC1996B

SWCP2163

LWC1Z96

LWC2Z97

LWC1Z193

LWC2Z194

LWC2Z195

User Manual/Mode d’emploi

BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING

INSTRUCTIONS IN THIS MANUAL.

AVANT L'UTILISATION, VEUILLEZ LIRE ET SUIVRE TOUTES LES RÈGLES DE SÉCURITÉ ET LES

INSTRUCTIONS D'UTILISATION DE CE MANUEL.

Write Model and Serial Numbers here:

Model: _____________________

Serial No.: __________________

Summit Division of Felix Storch, Inc.

An ISO 9001:2015 registered company

770 Garrison Avenue

Bronx, NY 10474

www.summitappliance.com

2

TABLE OF CONTENTS

Appliance Safety 3

Important Safeguards 4-5

Location of Parts 6-8

Installation Instructions 9-16

Before Using your Appliance 9

Installing your Appliance 9

Installing the Door Handle 10

Reversing the Door Swing 11

Built-in Cabinet Instructions 12-13

Electrical Connection 14

Extension Cord 14

Rearranging the Shelves 15

Placement and Storage of Wine 15-16

Operating your Appliance 17-18

Care and Maintenance 19

Troubleshooting 20

Limited Warranty 21

3

APPLIANCE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always

read and obey all safety messages.

This is the Safety Alert Symbol. This symbol alerts you to potential hazards that

can kill or injure you and others. All safety messages will follow the Safety Alert

Symbol and either the words “DANGER”, “WARNING” or “CAUTION”.

DANGER means that failure to heed this

safety statement may result in severe

personal injury or death.

WARNING means that failure to heed this

safety statement may result in extensive

product damage, serious personal injury, or

death.

CAUTION means that failure to heed this

safety statement may result in minor or

moderate personal injury, or property or

equipment damage.

All safety messages will alert you to what the potential hazard is, tell you how to reduce the chance

of injury, and let you know what can happen if the instructions are not followed.

4

IMPORTANT SAFEGUARDS

Before the appliance is used, it must be properly positioned and installed as

described in this manual, so read the manual carefully. To reduce the risk of

fire, electrical shock or injury when using the appliance, follow basic

precaution, including the following:

• Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and

do not use an extension cord.

• Replace all panels before operating.

• It is recommended that a separate circuit, serving only your appliance, be provided. Use

receptacles that cannot be turned off by a switch or pull-chain.

• Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or

explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity

of this or any other appliance. The fumes can create a fire hazard or explosion.

• Before proceeding with cleaning and maintenance operations, make sure the power line of the

unit is disconnected.

• Do not connect or disconnect the electric plug when your hands are wet.

• Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can

result in electrical shock or death.

• Do not attempt to repair or replace any part of your appliance unless it is specifically

recommended in this manual. All other servicing should be referred to a qualified technician.

• This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a) which

is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it

increase the greenhouse effect. Care must be taken during transportation and setting up of the

appliance that no parts of the cooling system are damaged. Leaking coolant can ignite and may

damage the eyes.

• In the event of any damage:

o Avoid open flames and anything that creates a spark,

o Disconnect from the electrical power line,

o Air the room in which the appliance is located for several minutes, and

o Contact the Service Department for advice.

• The more coolant there is in an appliance, the larger the room it should be installed in. In the

event of a leakage, if the appliance is in a small room, there is the danger of combustible gases

building up. For every ounce of coolant, at least 325 cubic feet of room space is required. The

amount of coolant in the appliance is stated on the data plate on the back of the appliance. It is

hazardous for anyone other than an authorized Service Person to carry out servicing or repairs

to this appliance.

• Take serious care when handling, moving, and using the appliance to avoid either damaging the

refrigerant tubing or increasing the risk of a leak.

• Replacing component parts and servicing shall be done by factory authorized service personnel

so as to minimize the risk of possible ignition due to incorrect parts or improper service.

5

FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL

• Use two or more people to move and install appliance. Failure to do so can result in back or

other injury.

• To ensure proper ventilation for your appliance, the front of the unit must be completely

unobstructed. Choose a well-ventilated area with temperatures above 60°F (16°C) and below

100°F (38°C). This unit must be installed in an area protected from the elements, such as wind,

rain, water spray or drips.

• The appliance should not be located next to ovens, grills or other sources of high heat.

• The appliance must be installed with all electrical, water and drain connections in accordance

with state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly

grounded in accordance with the National Electrical Code and local codes and ordinances is

required.

• Do not kink or pinch the power supply cord of appliance.

• The fuse (or circuit breaker) size should be 15 amperes.

• It is important for the appliance to be leveled in order to work properly. You may need to make

several adjustments to level it.

• Never allow children to operate, play with or crawl inside the appliance.

• Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may

damage or discolor the interior.

• Do not use this apparatus for other than its intended purpose.

Risk of child entrapment!

Child entrapment and suffocation are not problems of the past. Junked or abandoned appliances are

still dangerous, even if they will “just sit in the garage a few days”.

• Before discarding your old refrigerator:

o Take off the doors

o Leave the shelves in place so that children may not easily climb inside.

– SAVE THESE INSTRUCTIONS –

6

LOCATION OF PARTS

SWC1127B/LWC1Z96

SWC1926B/LWC1Z193

1

Right Upper Hinge

2

Control Panel

3

Door

4

Door Seal

5

Door Handle

6

Charcoal Filters

7

Wooden Shelf

8

Air Channel Plate

9

Vent Kick Plate

10

Right Lower Hinge

11

Adjustable Feet

7

SWC1966B/LWC2Z194

1

Right Upper Hinge

2

Air Channel Plate

3

Control Panel

4

Door

5

Door Seal

6

Door Handle

7

Wooden Shelf

8

Charcoal Filters

9

Vent Kick Plate

10

Right Lower Hinge

11

Adjustable Feet

8

SWCP2116/ LWC2Z97

SWCP2163/ LWC2Z195

1

Right Upper Hinge

2

Wire Shelf with S.S. Front Edge

3

Door

4

Door Seal

5

Door Handle

6

Air Channel Plate

7

Control Panel

8

Slide Light

9

Rolling Slideway

10

Charcoal Filters

11

Vent Kick Plate

12

Right Lower Hinge

13

Adjustable Feet

9

INSTALLATION INSTRUCTIONS

Before Using your Appliance

Remove the exterior and interior packaging, and check to make sure you have the following parts:

SWC1127B & SWC1926B & SWC1966B

(LWC1Z96 & LWC1Z193 & LWC2Z194)

SWCP2116 & SWCP2163

(LWC2Z97 & LWC2Z195)

Instruction Manual

Wooden Shelves

Wire Shelves with Rolling Slideways

Door Handle

• Before connecting this appliance to the power source, let it stand upright for approximately 2

hours. This will reduce the possibility of a malfunction in the cooling system from handling during

transportation.

• Clean the interior surface with lukewarm water using a soft cloth.

• The appliance is specially designed for wine storage; please do not put in other goods or food.

Installing your Appliance

• This appliance is designed for freestanding or built-in (fully recessed) installation.

• Place your appliance on a floor that is strong enough to support it when it is fully loaded. To level

your appliance, adjust the front leveling legs at the bottom of the appliance.

• Locate the appliance away from direct sunlight and sources of heat (stove, heater, radiator, etc.).

Direct sunlight may affect the acrylic coating and heat sources may increase electrical

consumption. Extremely cold ambient temperatures may also cause the unit not to perform

properly.

• Avoid locating the unit in moist areas.

• Plug the appliance into an exclusive, properly installed-grounded wall outlet. Do not under any

circumstances cut or remove the third (ground) prong from the power cord. Any questions

concerning power and/or grounding should be directed toward a certified electrician or a service

center authorized by Felix Storch, Inc.

10

Installing the Door Handle

This cooler includes one stainless steel handle that is not installed by the factory.

NOTE: The door handle is packaged inside, between the inner foam and the outer box. Do not

discard packaging until you have removed the handle.

To install the handle please follow these instructions:

1. Pull the door gasket (1) away from the door where the handle is to be installed, as shown in the

first illustration below. The gasket is easily displaced by hand, no tools are necessary.

2. Align the handle (2) with the screws pre-installed on the backside of the door. Tighten the screws

using a Phillips head screwdriver until the handle sets both flush and secured tightly against the

door frame. (DO NOT over-tighten as this will cause damage to the handle assembly).

3. Replace the door gasket to its original position.

11

Reversing the Door Swing

The diagram below will explain how to reverse the door swing of your beverage cooler. Be careful to

pay attention to the numbering of the steps below. Before reversing the door, please make sure

unplug the appliance and must be let it stand upright for approximately 2 hours before connecting to

the power source.

12

Built-In Cabinet Instructions

This unit is designed for both built-in and freestanding installation. If you plan to use this unit in a

built-in application, please follow the requirements shown below. Be sure that airflow under the

appliance is not blocked.

SWC1127B/LWC1Z96 and SWCP2116/LWC2Z97

Cabinet Opening Dimensions

IN (min)

CM (min)

Width

23 7/8”

60.5 cm

Depth

28”

71.2 cm

Height

55 3/4”

141.2 cm

13

SWC1926B/LWC1Z193. SWC1966B/LWC2Z194, and SWCP2163/LWC2Z195

Cabinet Opening Dimensions

IN (min)

CM (min)

Width

23 7/8”

60.5 cm

Depth

28”

71.2 cm

Height

70 3/4”

180 cm

14

Electrical Connection

This appliance should be properly grounded for your safety. The power cord of this appliance is

equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the

possibility of electrical shock.

Do not under any circumstances cut or remove the third ground prong from the power cord supplied.

For personal safety, this appliance must be properly grounded.

This appliance requires a standard three-prong 115/120 Volt AC ~/60Hz electrical ground wall outlet.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly

grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation

to have it replaced with a properly grounded 3-prong wall outlet.

The cord should be secured behind the appliance and not left exposed or dangling to prevent

accidental injury.

The appliance should always be plugged into its own individual electrical outlet which has a voltage

rating that matches the rating label on the appliance. This provides the best performance and also

prevents overloading house wiring circuits that could be a fire hazard from overheating. Never

unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from

the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise

damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the appliance, be careful not to damage the power cord.

Extension Cord

Because of potential safety hazards under certain conditions, it is strongly recommended that you do

not use an extension cord with this appliance. However, if you must use an extension cord it is

absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord

having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at

least 10 amperes.

Improper use of the grounded plug can result in the risk of electrical shock. If the power cord

is damaged, have it replaced by a service center authorized by Felix Storch, Inc.

15

Rearranging the Shelves

These instructions are intended for models SWCP2116/LWC2Z97 and SWCP2163/LWC2Z195.

1. First remove all wine and/or

beverages from the shelf.

2. Pull the shelf out to its limit,

and then press DOWN on

the left lever on the sliding

rail and press UP on the

right one simultaneously as

shown to the left.

3. Pull the shelf out while still

holding the levers in place.

Placement and Storage of Wines

Bottle loading sketch for the large shelves

16

• SWC1127B/ LWC1Z96 was designed to store a maximum of 127 Bordeaux bottles in total.

• SWCP2116/ LWC2Z97 was designed to store a maximum of 116 Bordeaux bottles in total.

• SWC1926B/ LWC1Z193 was designed to store a maximum of 165 Bordeaux bottles in total.

• SWC1966B/ LWC2Z194 was designed to store a maximum of 163 Bordeaux bottles in total.

• SWCP2163/ LWC2Z195 was designed to store a maximum of 163 Bordeaux bottles in total.

NOTE: Bottle sizes, even standard Bordeaux style, may vary in exact sizing and details between

different wine producers and bottling companies. Your overall bottle capacity may be slightly

lower depending on the exact bottle design you are storing. For wider Burgundy style bottles,

visit our website for storage guidelines.

SWC1127B

LWC1Z96

SWCP2116

LWC2Z97

SWC1926B

LWC1Z193

SWC1966B /SWCP2163

LWC2Z194/LWC2Z195

17

OPERATING YOUR APPLIANCE

It is recommended that you install the appliance in a place where the ambient temperature is

between 61º- 100º F (16º-38º C). If the ambient temperature is higher or lower than recommended

temperatures, the performance of the unit may be affected. For example, placing your unit in

extremely cold or hot conditions may cause interior temperatures to fluctuate. The range of

41º- 65º F (5º-18º C) may not be reached.

Temperature Ranges

WINE COOLER (SINGLE ZONE)

41 - 65º F

5 - 18º C

WINE COOLER (DUAL ZONE)

Upper Zone: 41 - 54º F

Lower Zone: 54 - 65º F

Upper Zone: 5 - 12º C

Lower Zone: 12 -18º C

Control Panel for SWC1127B/LWC1Z96 and SWC1926B/LWC1Z193

Control Panel for SWCP2116/LWC2Z97, SWC1966B/ LWC2Z194 and

SWCP2163/LWC2Z195

Recommended Temperatures for Chilling Wine

• Press and hold for two seconds on the control panel to turn the cooler on or off. When the

cooler is turned off, the appliance will stop working and totally shut down.

Light Setting

• The default light setting turns the light on automatically when the door is opened, and turn the

light off when the door is closed. The LCD screen will show in the default mode.

• Press and hold for three seconds to always keep the light turned on. The LCD screen will

show in this mode.

Temperature Setting

• Press the or to adjust the temperature up or down by 1ºF or 1ºC.

• Press to change the temperature display from Celsius to Fahrenheit or from Fahrenheit to

Celsius for SWC1127B/LWC1Z96 and SWC1926B/LWC1Z193 models.

• Press both the and together and hold for 3 seconds to change the temperature display

from Celsius to Fahrenheit or from Fahrenheit to Celsius for the SWCP2116/LWC2Z97,

SWC1966B/ LWC2Z194 and SWCP2163/LWC2Z195 models.

18

Warning System

• The door alarm will beep three times every five seconds, and the LCD screen will display

when the door is open for over 5 minutes. Press any key or close the door to stop the alarm.

• When the temperature inside the appliance is below 35.6ºF (2ºC) for over 3 hours, the alarm will

sound and the LCD screen will display . . . Press any key to stop the alarm from

sounding.

• When the temperature inside the appliance is above 77.ºF (25ºC) for over 6 hours, the alarm will

sound and the LCD screen will display . Press any key to stop the alarm from sounding.

Recommended Temperatures for Chilling Wine

To preserve the quality and taste of your fine wines, they must be stored at the ideal temperature

and ambient conditions. The ideal wine chilling temperatures are listed below:

Red Wines

58 - 65 ºF

15 - 18 ºC

Dry / White Wines

48 - 57 ºF

10 - 14 ºC

Rosé Wines

49 - 51 ºF

9 – 11 ºC

Sparkling Wines

40 - 47 ºF

5 - 8 ºC

19

CARE AND MAINTENANCE

Cleaning your Appliance

1. Turn off the power, unplug the appliance, and remove all items, including the shelves.

2. Wash the inside surfaces with a warm water and baking soda solution. The solution should be

about 2 tablespoons of baking soda to a quart of water.

3. Wash the shelves with a mild detergent solution.

4. Wring excess water out of the sponge or cloth when cleaning area of the controls, or any

electrical parts.

5. Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry

with a clean soft cloth.

6. Do not use steel wool or steel brush on the stainless steel. These will contaminate the stainless

steel with steel particles and rusting may occur.

Charcoal Filtration System

Your cellar is equipped with an active charcoal filtration system to ensure air purity, cooling

efficiency, and to maintain an odor-free cabinet for the storage of your wine. The filter assembly is

located at the rear panel inside your cooler. To replace your filter:

1. Remove the bottles/cans stored on the two shelves in front of the filter.

2. Remove the shelves and set aside to be replaced once you have changed the filter.

3. Hold the filter and turn it at 90 degrees in a counter-clockwise direction and then pull it out.

4. Remove the existing filter and replace with a new one.

5. Put the new filter into the hole and then turn the filter 90 degrees in a clockwise direction.

Power Failure

Most power failures are corrected within a few hours and should not affect the temperature of

your appliance if you minimize the number of times the door is opened. If the power is going to be

off for a longer period of time, you need to take the proper steps to protect your contents.

Moving your Appliance

• Remove all items.

• Securely tape down all loose items (shelves) inside your appliance.

• Tape the door shut.

• Be sure the appliance stays secure in the upright position during transportation.

• Protect outside of appliance with a blanket or similar item.

Energy-Saving Tips

The appliance should be located in the coolest area of the room, away from heat producing

appliances, and out of direct sunlight.

20

TROUBLESHOOTING

You can solve many common problems easily, saving you the cost of a possible service call. Try the

suggestions below to see if you can solve the problem before calling the service technician.

Problem

Possible Causes

The appliance is not running.

• The appliance is not plugged in.

• The appliance is not turned on.

• The voltage of the installation is not correct.

• The circuit breaker or fuse may have blown.

The appliance is not cold enough.

• Check the temperature control setting.

• Check if the ambient temperature is beyond

the appliance’s operating temperature.

• The door is opened too frequently.

• The door is not closed properly.

• The door is not sealing properly.

• Insufficient free space around the appliance.

The compressor starts and stops frequently.

• The external temperature is high.

• A large quantity of bottles has been put into

the cellar.

• The appliance is opened too frequently.

• The door is not properly closed.

• The appliance has not been properly set.

LED lights do not operate.

• The appliance is not plugged in.

• The fuse has blown.

• LED lights are broken.

• The light switch is off.

Vibrations

• Check and ensure the appliance is level.

The appliance makes too much noise.

• The rattling noise may come from the flow of

refrigerant, which is normal.

• Water can be heard circulating at the end of a

cooling cycle.

• Expansion and contraction of the internal

walls may cause a cracking sound.

• The appliance is not level.

• Check if the fan is in good condition.

The door does not close properly.

• The appliance is not level.

• The door seal is dirty or damaged.

• The shelves are not positioned correctly.

• A part of the contents is preventing the door

from closing.

Page is loading ...

Summit SWC1966B User manual

Summit SWC1966B User manual

in other languages

Related papers

Other documents