Wolf 826668 Installation guide

Wolf
Brand
Wolf
Model
826668
Type
Installation guide

Wolf 826668 Convection Steam Oven offers you a variety of cooking options that can help you create delicious meals. Steam, bake, roast and combine methods to cook even the most difficult dishes to perfection. The oven features 10 cooking modes, which makes it a multi-functional kitchen appliance that can replace many other devices. You can use it to prepare anything from juicy roasts to crispy pastries and delicate fish. This oven also features an automatic door that opens and closes smoothly, providing easy access to your food.

Wolf 826668 Convection Steam Oven offers you a variety of cooking options that can help you create delicious meals. Steam, bake, roast and combine methods to cook even the most difficult dishes to perfection. The oven features 10 cooking modes, which makes it a multi-functional kitchen appliance that can replace many other devices. You can use it to prepare anything from juicy roasts to crispy pastries and delicate fish. This oven also features an automatic door that opens and closes smoothly, providing easy access to your food.

page 1 of 3
821979 REV-F 05/2018
wolfappliance.com 800.222.7820
Convection Steam Oven
Accessory Handle Installation
CONTENTS
1 Handle
2 Standoff
2 Washer, star
2
Screw, #10-24 x 1
3
⁄4" (use with Tubular handle)
2 Screw, #10-24 x 2" (use with Pro handle)
NOTICE: Depending on the model, additional components
may be included with this kit but not utilized.
INSTALLATION
1 Open the oven door to the fully open position then rotate each
hinge latch to the open position. Refer to the illustration below.
2 Once both hinge latches are in the open position, rotate
the door to the at rest position. Then carefully lift up and
out to remove the door. Refer to the illustration below.
3 Once the door has been removed, place the door on a
protected work surface handle side up.
4 Remove the inner screw on each side of the door assembly.
Once the inner screws have been removed, rotate the
bottom edge of the glass upward slightly until the lower
glass bracket clears the lower door assembly then pull the
glass towards your body until the glass clears the upper
door assembly. Refer to the illustration below.
5 Now that the glass has been removed place it handle side
down on a protected surface. Remove and discard the
existing handle and screws.
6 Tubular – Place one star washer on each of the two 1
3
⁄4"
screws provided. Align the new handle with the existing
holes, then tighten. Do not over tighten. This may cause
the oven glass to break.
Pro – Remove and discard the screws securing the
standoffs to the handle. Place one star washer on each
of the two 2" screws provided. Loosely place standoffs on
the handle, then align the new handle with existing holes.
Verify the standoffs and standoff graphics are properly
positioned, then tighten. Do not over tighten as this may
cause the oven glass to break.
T
EMP
MODE
LIGHT
WATER
TIME
OFF
POWER
ON
Door at rest.
OPEN
POSITION
CLOSED
POSITION
Hinge latch.
INNER SCREW
LOWER
DOOR
ASSEMBLY
LOWER
GLASS
BRACKET
Inner screw.
page 2 of 3
wolfappliance.com 800.222.7820
Convection Steam Oven
Accessory Handle Installation
7 Before placing the door glass back on the door assembly,
verify the gaskets are properly positioned. Refer to the
illustrations below.
8 Gently slide the oven glass under the upper door
assembly. Once the lower glass ange clears the lower
assembly, rotate downward. Verify the gaskets remained in
the proper position before moving on to the next step.
9 With the oven glass in position, reinstall two inner screws.
10 Place the oven door hinges back into the hinge receivers.
When hinges are properly position, the door should open
and close without resistance.
11 Once the hinges are properly positioned, open the door
fully and rotate the hinge clips back into the closed
position. Open and close the door multiple times to ensure
proper placement.
LOWER
GASKET
UPPER
GASKET
Gasket placement.
wolfappliance.com 800.222.7820
page 3 of 3
Drop-Down Door Microwave
Accessory Handle Installation
CONTENTS
1 Handle
2 Standoff
2 Screw, #10-24 x
1
⁄2"
NOTICE: Depending on the model, additional components
may be included with this kit but not utilized.
INSTALLATION
1 Use a 2.5mm Allen wrench to loosen the set screws on
the inside of each existing handle standoff, then remove
the handle.
2 Place standoffs on new handle and secure using two
#10-24 x
1
⁄2" screws.
3 Tubular – Verify the angled portion of the standoff is
positioned inward.
Pro – Verify the logos on the outside of the standoffs are
positioned properly.
4 Place the new handle on the door and secure the two set
screws using a 2.5mm Allen wrench. Do not over tighten.
  • Page 1 1
  • Page 2 2
  • Page 3 3

Wolf 826668 Installation guide

Wolf
Brand
Wolf
Model
826668
Type
Installation guide

Wolf 826668 Convection Steam Oven offers you a variety of cooking options that can help you create delicious meals. Steam, bake, roast and combine methods to cook even the most difficult dishes to perfection. The oven features 10 cooking modes, which makes it a multi-functional kitchen appliance that can replace many other devices. You can use it to prepare anything from juicy roasts to crispy pastries and delicate fish. This oven also features an automatic door that opens and closes smoothly, providing easy access to your food.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents