WORX RACING COMPONENTS WR04074 User manual

Brand
WORX RACING COMPONENTS
Model
WR04074
Type
User manual

WORX RACING COMPONENTS WR04074

The WR04074 is a rear exhaust system designed for the 2021+ SeaDoo RXPX 300. You can use it to upgrade your personal watercraft and get the most out of your riding experience. This system is easy to install and comes with all the necessary parts and instructions.

With the WR04074, you'll enjoy:

  • Increased power and performance
  • Improved sound quality
  • Reduced water ingestion

If you're looking for a way to take your SeaDoo RXPX 300 to the next level, the WR04074 rear exhaust system is the perfect choice. Order yours today and experience the difference!

WORX RACING COMPONENTS WR04074

The WR04074 is a rear exhaust system designed for the 2021+ SeaDoo RXPX 300. You can use it to upgrade your personal watercraft and get the most out of your riding experience. This system is easy to install and comes with all the necessary parts and instructions.

With the WR04074, you'll enjoy:

  • Increased power and performance
  • Improved sound quality
  • Reduced water ingestion

If you're looking for a way to take your SeaDoo RXPX 300 to the next level, the WR04074 rear exhaust system is the perfect choice. Order yours today and experience the difference!

1. Make sure ski is secure and on a
at surface. Remove lanyard and
disconnect battery.
2. Pull the rear plastic and seat housing
o the ski.
3. Undo and remove the labelled
bolts(1-13) with a torx bit.
4. Disconnect OEM Exhaust Hose and
retain hose clamps (14-15).
5. Cut and remove the zip ties shown
before moving the hoses out of the
way.
6. Unclip the straps securing the
resonator box in place.
7. Undo hose clamp (16) pictured before
removing the resonator box.
TIP: Pull the resonator up and rotate
the right side of it towards the front of
the ski before pulling it from the cavity.
2021+ SeaDoo RXPX 300
Rear Exhaust
[email protected] | worx.com.au
Australia: United States:
[email protected] | worxracingusa.com
10B 354 Brisbane Rd Arundel QLD 4214
Phone: +61 7 5563 1031 9251 Orco Parkway Unit G, Riverside CA 92509
Phone: (951) 684-9679
Part No. WR04074
Suits Models:
• 2021+ RXP-X
Parts Supplied:
INSTALLATION INSTRUCTIONS:
IMPORTANT: READ ALL INSTRUCTIONS BEFORE PROCEEDING WITH INSTALLATION
Tools Required:
• Blue Loctite
• Marine Sealant
• Electric Drill
• 6mm Drill Bit
• 79mm (3 1/8”) Holesaw
• T27 Torx Bit
• 5mm Hex Key
• 10mm Spanner
• WR04074-1 Silicon Exhaust
Hose
• Exhaust Outlet
• Exhaust Block O Cap
• Exhaust Outlet Retainer Ring
• 7 x M6 x 30mm Cap Head Bolts
• 1 x M6 Nyloc Nut
12
513
14
15
12
11
34
6
7 8
10
9
[email protected] | worx.com.au [email protected] | worxracingusa.com
12. Using a 79mm hole saw, slowly drill
out the hole for your exhaust outlet.
8. Place the exhaust block o cap in
the OEM exhaust outlet hose before
retightening the hose clamp.
13. Place the Worx Exhaust outlet
through the whole and ensure it is
rotated as pictured below. Holding
the outlet rmly, use a 6mm to drill
out your bolt locations.
TIP: Drill out the location for the two
bolts pictured below(17-18), before
inserting them and using them to
ensure the outlet stays in the correct
position while drilling out the nal
four bolt(19-22) holes.
14. Run a bead of marine silicone
around the lip of the exhaust outlet.
15. Place the retainer ring behind the
outlet hole and slide the exhaust
outlet through it. Begin lightly
tightening the bolts through the
outlet and ring a little at a time
before nally securing them tightly.
9. Remove the ladder atttachement on
the rear left side of the hull, retain
bolts and nuts
10. Line up the template (page 4) with
the three holes from the ladder
attachment.
PLEASE NOTE: You should now line up
the exhaust with the waterbox and outlet
location to ensure everything is correct
before drilling and making permanent
modications.
11. Using a 6mm drill bit, make a pilot
hole for your holse saw.
17
18
19
20
21
22
16. Attach the hose from the waterbox
to the new outlet and use OEM hose
clamps to fasten each end securely.
17. Using a supplied M6 Nyloc Nut and
Bolt, plug the remaining hole left by
the ladder attachment. Silicone can
be used if any water leaks through.
16. Ensure all connections are tight
and secure before reinstalling all
panels and seat.
[email protected] | worx.com.au [email protected] | worxracingusa.com
[email protected] | worx.com.au [email protected] | worxracingusa.com
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
RXPX RXPX RXPX
WR04074 TEMPLATE
79mm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

WORX RACING COMPONENTS WR04074 User manual

Brand
WORX RACING COMPONENTS
Model
WR04074
Type
User manual

WORX RACING COMPONENTS WR04074

The WR04074 is a rear exhaust system designed for the 2021+ SeaDoo RXPX 300. You can use it to upgrade your personal watercraft and get the most out of your riding experience. This system is easy to install and comes with all the necessary parts and instructions.

With the WR04074, you'll enjoy:

  • Increased power and performance
  • Improved sound quality
  • Reduced water ingestion

If you're looking for a way to take your SeaDoo RXPX 300 to the next level, the WR04074 rear exhaust system is the perfect choice. Order yours today and experience the difference!

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents