Zevni Z-O8JFMIJ2-48W3 User manual

Z-O8JFMIJ2-48W3
Zevni
Brand
Zevni
Model
Z-O8JFMIJ2-48W3
Type
User manual

This manual is also suitable for

[email protected]
Page: - 1 - / 3
Item Number: Z-N8Z2MJIE-48W2
WARNING (To reduce the risk of fire, electric shock, or personal injury):
1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
»
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
»
Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps
between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It
must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED
(NOT INCLUDED):
Before starting assembly and installation please prepare the needed
tools as below picture
Ladder Philips Head or Flat
Blade Screwdriver Electrical Tape Pilers Wire Cutter/Stripper
[email protected]
Page: - 2 - / 3
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and accessories are
included as shown in the above illustration.
2. Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity
until the work is done.
PARTS INCLUDING:
(C) Green ground screw (1)
(D) Mounting plate (1)
(E) Back plate (1)
(F) Knob nut (2)
(G) Socket (2)
(H) Lampshade (2)
(I) Socket ring (2)
ACCESSORIES ENCLOSED:
3. Make assembly
»
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
»
Place the wall switch in the “OFF” position.
(A) Mounting screw (2)
(B) Plastic wire connector (3)
(J) Socket wrench (1)
[email protected]
Page: - 3 - / 3
4. Check everything is installed properly, then you could turn on the light. Enjoy!
Step A1 »
Step A2 »
Step A3 »
Unscrew knob nuts (F) from back plate (E), then set them aside for later installation.
Carefully pass the supply wires from the outlet box through mounting plate (D).
Secure mounting plate (D) to the outlet box with mounting screws (A).
Make wire connections
Connect wires as below wires connection shown.
PLEASE NOTE THAT GROUND WIRE IS BARE
COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Twist wires together with plastic wire connectors until tightly joined, and wrap each
connector with approved electrical tape. Be sure that no wire strands are exposed and then
carefully tuck all wires into the outlet box.
Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate
(E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with knob nuts (F).
If not, remove back plate (E), adjust the threaded length of pre-assembled
mounting screws on mounting plate assembly (D):
• Unscrew the pre-assembled hex nuts;
• Screw the pre-assembled mounting screws in or out of mounting plate (D);
• When the secure length is achieved, tighten the pre-assembled hex nuts and
back to Step A4.
2) Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the
socket.)
ORDERING PARTS
Keep this sheet for future reference in case you need
to order replacement parts. All parts for this fixture can
be ordered from the place of purchase. Be sure to use
exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Do not use
abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
Connect Black or
Red Supply Wire to: Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black without
tracer Clear, Brown, Gold or Black with
tracer
Insulated wire(other than green)
with copper conductor Insulated wire(other than green)
with silver conductor
* Note: When parallel wires (SPT I&
SPT ll) are used. The neutral wire is
square shaped or ridged and the
other wire will be round in shape or
smooth (see illus.)
OUTLET BOX
GROUND
DIMPLES
GREEN GROUND
SCREW
CUPPED
WASHER
FIXTURE
GROUND
Neutral Wire
GREEN GROUND
SCREW
OUTLET BOX
GROUND
FIXTURE
GROUND
Connect ground wires according to the below chart Connect wires according to the below chart
Step A5 » 1) Remove socket ring (I) from socket (F), and carefully place lampshade (H) on socket (F), then
secure lampshade (H) by tightening socket ring (I) with socket wrench (J).
  • Page 1 1
  • Page 2 2
  • Page 3 3

Zevni Z-O8JFMIJ2-48W3 User manual

Z-O8JFMIJ2-48W3
Zevni
Brand
Zevni
Model
Z-O8JFMIJ2-48W3
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents