1
2
3
Smart Doorbell
Product Manual V1.0
Before using this product, please read this manual carefully and keep
it for future reference.
Product Introduction
Brightness
sensor
Anti-dismantle
screw socket
AC power
interface
Battery
compartment
Package Contents
Please check if the device is in good condition and all accessories are
included.
manual
Smart doorbell x1
Screws package x1 User’s manual x1
USB charging cable x1 Base x1
Quick Start Guide
Download the WowCam App
You can either scan the QR code or search "WowCam" in the App
Store or Google Play.
Add device
1
2
wollof ,”ecived dda“ no kcilc ,yllufsseccus ppA eht otni gniggol retfA
instructions from the app then proceed. After connecting the device,
you may press the call button and enjoy the video call.
Device Sharing
Invite your friends to download and install WowCam App, and
register to log in.
”noitativni tnuoccA“ esoohc nac uoy ,noci gnirahs eht gnikcilc yB
.ecived eht erahs ot ”noitativni edoc RQ“ ro
1
2
WowCam is still waiting for you!
Just tap the button to add your own WowCam!
Add device
Device
Installation Guide
Note: If you install the doorbell wirelessly, please be remindful of the battery
level of the smart doorbell. When the call button is flashing red, it means for low
power. You may use any 5v charger to charge the battery, or you may use a USB
cable as well.
Wireless installation
Use 4 screws (KA3x25mm) to mount the mounting bracket on
the wall, or directly attach the mounting bracket to the wall with
the adhesive tape comes together. (Please note: You may not
mount it on iron gates.)
Buckle doorbell and base accordingly and push down slightly to
fix it.
1
2
Anti-dismantle
screw
Wall Base
Screws
Wall Base
3M adhesive tape
Hardwired installation (Recommended)
Before Installing, please make sure to disconnect any power
source that is connected with the doorbell. Slide across the
electric cable through the bottom of the smart doorbell and use
4 screws to stabilize the doorbell base. ( Please note: you may
not mount it on iron gates. )
Please connect the two electric wires to the screws ( power
requirement : 10-24VAC ) and insert through the back part of the
doorbell for power.
Buckle doorbell and base accordingly and push down slightly to
fix it. After inserting the anti-dismantle screw in the bottom of
the doorbell, the doorbell installation is completed.
Note: Remove the anti-dismantle screw before removing the doorbell from the
base.
2
3
1
Wall Base
Screws
Please do not install the product in a harsh environment. The
product may be damaged if exposed to high temperatures, high
humidity, dust, and smoke, etc.
The WowCam App and the device firmware will be updated
occasionally. Please update when the software notifies you that an
update is available.
Warning
The common operations can be checked from "Help and Feedback" in WowCam
App.
The device is powered by rechargeable lithium batteries. With fully
charged, the battery life approx be six months. The mobile device APP
will be prompted while the battery voltage is low. Please charge the device
after received the reminder.
Keep the camera in range of your router. Make sure to pick a place within
range of your network. Thick or insulated doors can greatly reduce the
strength of your Wi-Fi signal even if your router is close by, so you should
try streaming video before you mount your camera.
The device is a low power consumption intelligent products, can support
remote wake up from the APP, PIR human detection, press doorbell wake
up. The devic will be works for 30 seconds after wake up then be in the
resting state eautomatically and until to next waking up.
Note for using
Front side of the doorbell
Top surface of doorbell
Microphone
Call button
Camera
PIR sensor
Doorbell bottom
Reverse side of the doorbell
Speaker
Reset button
USB port TF card slot
Power Consumption Standby200 uA,
Working170 mA
Three 18650 specification batteries, work regularly for 9 months.
*Reminder: The above product functions are subject to change without notice,
please refer to the actual product, thank you!
Within600 ms
Three pcs 18650 lithium battery
Two18650 specification batteries
Device Button, Motion Detection,
Remote Live View
Cloud storage or 8G/16G/32G TF Card
Device SD Card recording(20 seconds)
Two-way talk with noise cancellation
IEEE 802 11 b/ g/ n
6*850mm
166°
1280* 720
Technical Specification
(Needs to be purchased separately)
Three 18650 specification batteries work regularly for 9
months
Million HD pixels collocated with wide-angle lens
Support mobile phone remote fast wakeup device
within 1 second.
2.4G Wi-Fi connection
High quality two-way talk with noise cancellation
Support PIR motion detection,when someone hovers at
the door, immediately alerts push notifications to the
mobile phone.
Day and night mode automatic switching, whether day or
night, the image is clearly visible, for your、safety and
family security.
Reset: 1.Press the button of Ding-dong for 5 seconds.
Code Pairing: 1.Short press the button of Ding-dong responder,
indicator light is always on
2.Press the button of doorbell to make the code
successful
Number of connections: 1 Ding-dong can connect with12
Doorbells;
1 Doorbell can connect with unlimited
amount of Ding-dongs.
Function Introduction
Ding-dong Pairing
Resolution
Field of Angle View
IR LED
Wi-Fi
Audio
Recording
Storage
Battery
Monitoring
Notifications
Device Wakeup
Power Consumption
1
Doorbell Wireless Battery Video Quick start guide
Belkin Valkia Wireless Battery Video Doorbell User guide
Tuya T23 User manual
Tuya M3 User manual
Mercury VDB720P-V2 Smart Wi-Fi HD Video Doorbell User manual
Denver SHV-120 User manual
Denver SHV-120 User manual
Tuya WF001 User guide
Smart Video Doorbell User manual
AKASO Video Doorbell 2 User manual
