VEVOR DZ-260ZKBZJ400W01V1 User manual

DZ-260ZKBZJ400W01V1
VEVOR
Brand
VEVOR
Model
DZ-260ZKBZJ400W01V1
Type
User manual

This manual is also suitable for

1
DZ-260 VACUUM PACKING MACHINE
OPERATION INSTRUCTION
BEFORE OPERATION, PLEASE READ THIS
OPERATIONAL MANUAL CAREFULLY
2
One、Function
The machine uses plastic film or plastic aluminum foil film as packaging materials to
vacuum packaging liquid, solid, pasty foods, grains, fruits, pickles, preserved fruits,
chemicals, medicinal materials, electronic components, precision instruments, rare
metals, etc. Vacuum-packed items can prevent oxidation, mildew, moth-eaten rot,
moisture, and extend the shelf life. It is especially suitable for tea, food, medical
stores, research institutions and other industries. It has the advantages of beautiful
appearance, compact structure, high efficiency, and easy operation.
Two、Specification
Three、Operating process
1. Oil-filling method ：remove the fixing bolt from the hex wrench at the bottom of
the machine, turn on the machine, unscrew the oil mist filter of the vacuum pump,
and fill the vacuum pump oil. The oil level shall not be lower than 1/2 of the oil
window. , Not higher than 3/4 visible from the oil window, prohibit higher than 3/4
visible from the oil window, and forbid the vacuum pump to start working without oil.
It is recommended that the vacuum pump oil be replaced after the machine works
continuously for 800H.
2. Turn on the power supply that matches the machine, press the power switch, and
the operation panel light is on, indicating that the power is turned on.
Model
Voltage
V/HZ
Power
W
Current
A
Pumping
rate
S
Inlet
diameter
MM
Noise
DB
External
dimension
MM
DZ-260
S
110/60
220/50
260
5
1.2L
Ø6
≦80
410X320X
320
3
3. Click the setting button on the control panel and select the setting target, a. The
vacuum time is generally set to 30-40S, click the increase or the button to decrease
to set the ideal vacuum time. b. Sealing time: Click the set button twice, the sealing
time is generally set to 1.5-2S, and the sealing time is set according to the thickness
of the vacuum bag. It is forbidden to set the sealing time too long and burn the
sealing heating bar. c. After the sealing time is set, click the set button again to set
the cooling time, usually 3-5S. After the cooling time is set, click the set button, and
the control panel will display the letter E. d. The setting process is over.
4. Put the product to be packaged in the working room of the machine, open the
pressure bag, place the vacuum bag mouth flat on the sealing strip, put back the
pressure bag, and cover the vacuum machine lid, which needs to be pressed by
hand during operation. Click the start button on the front end of the vacuum
machine cover, the vacuum machine starts to work, and the vacuum meter starts to
run. If the pointer of the vacuum gauge does not move after the machine starts to
work, you need to apply a little pressure to the front of the vacuum machine cover
until the pointer of the vacuum gauge starts to move. After the vacuum meter
pointer starts to run, you can leave the machine with your hand, and the machine
automatically completes the packaging process. The product and the vacuum bag
must match each other. The packaged product needs to be filled with the vacuum
bag to achieve a good vacuum effect. If a larger vacuum bag packs a smaller
product, the vacuum effect is not ideal. The vacuum bag must be filled with the
product to be packaged in order to show a good vacuum effect.
Four、Common faults and solutions
1. The control panel shows that there is no power: Check whether the wires of the
internal power input part of the machine are loose or fall off.
2. The vacuum pump is not working: The control panel is working and running. The
vacuum pump is not rotating. Check whether the vacuum pump power supply wire
is loose or falling off.
4. The air in the vacuum bag cannot be pumped away: The vacuum time is not
enough, prolong the vacuum time, and the product in the vacuum bag is filled, as
close as possible to the sealing strip.
5. After the packaging process, the vacuum lid does not open: Check and repair the
air release solenoid valve.
4
Five、Circuit diagram
Six、Spareparts
1.One vacuum machine.
2. One manual.
3.One hexagon wrench.
4. A heating strip.
5.One piece of Teflon cloth.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

VEVOR DZ-260ZKBZJ400W01V1 User manual

DZ-260ZKBZJ400W01V1
VEVOR
Brand
VEVOR
Model
DZ-260ZKBZJ400W01V1
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents