Homelite HL80923 User manual

SAVE THIS MANUAL FOR FUTURE REFERENCE

Ce nettoyeur haute pression a été conçu et fabriqué conformément

aux strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenu, il vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’utiliser ce produit.

Merci de votre achat.

Su lavadora de presión ha sido diseñada y fabricada de confor-

midad con las estrictas normas para brindar fiabilidad, facilidad

de uso y seguridad para el operador. Con el debido cuidado, le

brindará muchos años de sólido y eficiente funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones,

el usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

Your pressure washer has been engineered and manufactured to our high standard for dependability, ease of operation,

and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before

using this product.

Thank you for your purchase.

OPERATOR’S

MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

3100 PSI PRESSURE WASHER

NETTOYEUR HAUTE PRESSION

DE 3 100 PSI

LAVADORA A PRESIÓN

DE 3 100 PSI

HL80923

Page is loading ...

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below may result in electric shock,

fire and/or carbon monoxide poisoning which will cause

death or serious personal injury.

READ ALL INSTRUCTIONS

 Know your tool. Read the operator’s manual carefully.

Learn the machine’s applications and limitations as well

as the specific potential hazards related to this tool.

Keep guards in place and in working order. Never oper-

ate the tool with any guard or cover removed. Make sure

all guards are operating properly before each use.

 Remove adjusting keys and wrenches. Form habit of

checking to see that keys and adjusting wrenches are

removed from tool before turning it on.

 To reduce the risk of injury, keep children and visitors

away. All visitors should wear safety glasses and be kept

a safe distance from work area.

Keep the area of operation clear of all persons,

particularly small children, and pets.

Do not operate the engine in a confined space where

dangerous carbon monoxide fumes can collect.

Carbon monoxide, a colorless, odorless, and extremely

dangerous gas, can cause unconsciousness or death.

 Use right tool. Don’t force tool or attachment to do a

job it was not designed for. Don’t use it for a purpose not

intended.

 Dress properly. Do not wear loose clothing, gloves,

neckties, or jewelry. They can get caught and draw you

into moving parts. Rubber gloves and nonskid footwear

are recommended when working outdoors. Also wear

protective hair covering to contain long hair.

Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve

your footing on slippery surfaces.

Exercise caution to avoid slipping or falling.

 Always wear safety glasses with side shields. Everyday

eyeglasses have only impact-resistant lenses; they are

NOT safety glasses.

 Don’t overreach or stand on unstable support. Keep

proper footing and balance at all times.

 Use only recommended accessories. The use of

improper accessories may cause risk of injury.

 Follow the maintenance instructions specified in this

manual.

 Check damaged parts. Before further use of the

tool, a

guard or other part that is damaged should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged must

be properly repaired or replaced by an authorized service

center to avoid risk of personal injury.

 Never leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

Keep the engine free of grass, leaves, or grease to

reduce the chance of a fire hazard.

 Keep the exhaust pipe free of foreign objects.

Follow manufacturer’s recommendations for safe

loading, unloading, transport, and storage of

machine.

 Be thoroughly familiar with controls. Know how to stop

the product and bleed pressure quickly.

 Keep tool dry, clean, and free from oil and grease.

Always use a clean cloth when cleaning. Never use

brake fluids, gasoline, petroleum-based products, or any

solvents to clean tool.

 Stay alert and exercise control. Watch what you are

doing and use common sense. Do not operate tool when

you are tired. Do not rush.

Do not operate the product while under the influence

of drugs, alcohol, or any medication.

Check the work area before each use. Remove all

objects such as rocks, broken glass, nails, wire, or string

which can be thrown or become entangled in the

machine.

Do not use tool if switch does not turn it off. Have

defective switches replaced by an authorized service

center.

Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent accidental starting.

 Avoid dangerous environment. Don’t use in damp or

wet locations or expose to rain. Keep work area well

lit.

 Never use in an explosive atmosphere. Normal

sparking of the motor could ignite fumes.

Do not operature while smoking or near an open

flame.

Do not operate around dry brush, twigs, cloth rags, or

other flammable materials.

 WARNING: Risk of injection or injury – Do not direct

discharge stream at persons.

Page 4 — English

SPECIFIC SAFETY RULES

 Never direct a water stream toward people or pets,

or any electrical device.

Before starting any cleaning operation, close doors

and windows. Clear the area to be cleaned of debris,

toys, outdoor furniture, or other objects that could create

a hazard.

Never pick up or carry a machine while the engine is

running.

 Never start the machine if ice has formed in any part

of the equipment.

 Do not use acids, alkalines, solvents, flammable

material, bleaches, or industrial grade solutions

in this product. These products can cause physical

injuries to the operator and irreversible damage to the

machine.

 Always operate the machine on a level surface. If the

engine is on an incline, it could seize due to improper

lubrication (even at the maximum oil level).

 WARNING: High pressure jets can be dangerous

if subject to misuse. The jet must not be directed at

persons, animals, electrical devices, or the machine

itself.

Never attempt to make any adjustments while the

engine (motor) is running (except where specifically

recommended by the manufacturer).

 Protective covers must always cover rotating parts

when the engine is running.

Keep cooling air intake (recoil starter area) and muffler

side of the engine at least 3 feet away from buildings,

obstructions, and other combustible objects.

Keep the engine away from flammables and other

hazardous materials.

Keep away from hot parts. The muffler and other engine

parts become very hot; use caution.

Do not touch the spark plug and ignition cable when

starting and operating the engine.

 Check fuel hoses and joints for looseness and fuel

leakage before each use.

 Check bolts and nuts for looseness before each use.

A loose bolt or nut may cause serious engine prob-

lems.

 Before inflating the tires, confirm that the bolts in-

stalled in the wheel hubs are securely tight. The tire

should be inflated only using a hand pump with inflation

pressure no greater than 25 psi. Confirm the pressure

of the tires during and after inflation using a reliable tire

pressure gauge.

Always refuel outdoors. Never refuel indoors or in a

poorly ventilated area.

Never store the machine with fuel in the fuel tank

inside a building where ignition sources are present,

such as hot water and space heaters, clothes dryers,

and the like.

If the fuel tank has to be drained, do this outdoors.

To reduce the risk of fire and burn injury, handle fuel

with care. It is highly flammable.

Do not smoke while handling fuel.

Add fuel before starting the engine. Never remove the

cap of the fuel tank or add fuel while the engine is running

or when the engine is hot.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Replace all fuel tank and container caps securely.

Wipe spilled fuel from the unit. Move 30 feet away from

refueling site before starting engine.

If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

Never attempt to burn off spilled fuel under any

circumstances.

Before storing, allow the engine to cool.

Store fuel in a cool, well-ventilated area, safely away

from spark and/or flame-producing equipment.

Store fuel in containers specifically designed for this

purpose.

Empty fuel tank and restrain the unit from moving

before transporting in a vehicle.

When servicing use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

ONLY use cold water.

Make sure minimum clearance of 3 feet is maintained

from combustible materials.

Never spray close to the surface to be cleaned as you

can damage the surface.

Save these instructions. Refer to them frequently and

use them to instruct other users. If you loan someone this

tool, loan them these instructions also.

Page 5 — English

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

CAUTION:

(Without Safety Alert Symbol) Indicates a situation that may result in property

damage.

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Read The Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection Always wear eye protection marked to comply with ANSI Z87.1.

Hot Surface

To reduce the risk of injury or damage, avoid contact with any hot

surface.

Risk of Injection

To reduce the risk of injection or injury, never direct a water stream

towards people or pets or place any body part in the stream. Leak-

ing hoses and fittings are also capable of causing injection injury.

Do not hold hoses or fittings.

Risk of Explosion

Fuel and its vapors are explosive and can cause severe burns or

death.

Risk of Fire

Fuel and its vapors are extremely flammable and explosive. Fire

can cause severe burns or death.

Toxic Fumes

Gas products emit carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Page 6 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper

interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Kickback

To reduce the risk of injury from kickback, hold the spray wand

securely with both hands when the machine is on.

Electric Shock

Failure to use in dry conditions and to observe safe practices can

result in electric shock.

Chemical Burns

To reduce the risk of injury or damage, DO NOT USE ACIDS,

ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,

OR INDUSTRIAL GRADE SOLUTIONS in this product.

FEATURES

PRODUCT SPECIFICATIONS

Engine ...............................................................................................................................................................Honda GX200

Fuel Tank Capacity .....................................................................................................................................................0.95 gal

Maximum Pounds Per Square Inch Pressure* ......................................................................................................... 3,100 psi

Maximum Gallons Per Minute* ...................................................................................................................................2.8 gpm

Maximum Inlet Water Temperature ................................................................................................................................104˚F

*Max. rating determined by PWMA Standard 101, when tested with red nozzle

KNOW YOUR PRESSURE WASHER

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

ENGINE SWITCH

The engine switch is used in combination with the recoil

starter grip to start the engine. It is also used to turn the

engine off.

FUEL TANK

This fuel tank has a maximum capacity of 0.95 gal. Use

unleaded automotive gasoline in the engine.

HONDA GX200 ENGINE

This Honda engine enables the pressure washer to achieve

3,100 psi (pounds per square inch) at a rate of 2.8 gpm

(gallons per minute). Please read the engine manual included

with this product.

HOSE STORAGE

Once the high pressure hose is rolled, hang it on the back of

the machine using the stretch strap to secure in place.

PRESSURE REGULATOR

The high pressure pump has a regulator that allows adjust-

ment from high to low pressure.

RECOIL STARTER

The recoil starter is pulled to start the machine.

SPARK ARRESTOR

This engine is not factory equipped with a spark arrestor.

In some areas it is illegal to operate an engine without a spark

arrestor. A spark arrestor is available by calling customer

service for assistance.

THERMAL RELEASE VALVE

This pump feature will prevent water temperatures from

reaching harmful levels by releasing a small amount of

water. Once the water has drained, the thermal relief valve

will reset itself.

TRIGGER HANDLE

The trigger handle has a gripping surface that provides added

control of the spray wand and helps reduce fatigue.

TRIGGER WITH LOCK OUT

Pulling the trigger releases a stream of water for high

pressure cleaning. The lock out provides protection against

unauthorized use.

Page 7 — English

UNPACKING

This product requires assembly.

 Carefully cut the box down the sides then remove the

product and any accessories from the box. Make sure

that all items listed in the packing list are included.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

NOTE: This product is heavy. To avoid back injury, lift with

your legs, not your back, and get help when needed.

 Inspect the product carefully to make sure no breakage

or damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the product.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

PACKING LIST

Pressure Washer

25 ft. High Pressure Hose

Trigger Handle

Spray Wand

Quick-connect Nozzles (4)

Injection Hose

Injection Hose Filter

4-Cycle Engine Oil (SAE 30 or SAE 10W30)

Axle (2)

Hitch pins (2)

Washers (2)

Wheels (2)

Handle

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

product until the parts are replaced. Use of this product

with damaged or missing parts could result in serious

personal injury.

WARNING:

Do not attempt to modify this product or create acces-

sories not recommended for use with this product. Any

such alteration or modification is misuse and could result

in a hazardous condition leading to possible serious

personal injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

ATTACHING THE WHEEL ASSEMBLY

See Figure 2.

 Locatethefollowingitems:

Axle (2)

Hitch pins (2)

Washers (2)

Wheels (2)

 Slide the axle through the hole in the center of the

wheel.

 Slide a washer onto the axle.

 Lift the machine and slide the axle into the wheel mount-

ing hole in the machine base as shown.

 Push the hitch pin into the hole on the end of the axle to

secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until

the center of the pin rests on top of the axle.

 Repeat with the second wheel.

INSTALLING THE HANDLE

See Figure 3.

To install the handle:

 Push and hold the button on the handle as you slide the

handle into the holes in the frame.

NOTE: Before use, pull the handle up until the lock

button snaps through the locking slot to secure the

handle in place.

CONNECTING HIGH PRESSURE HOSE TO

TRIGGER HANDLE

See Figure 4.

 Pull back and hold the collar on the high pressure hose.

Inserttheinletcoupleronthetriggerhandleintothecollar.

 Releasethecollarandpushuntilitlocksintoplace.Pull

on the hose to be certain it is properly secured.

ASSEMBLY

Page 8 — English

ASSEMBLY

ASSEMBLING THE TRIGGER HANDLE

See Figure 5.

To attach the spray wand:

 Place the threaded end of the spray wand in the connector

on the end of the trigger handle.

 Turn the connector clockwise until it stops. This secures

the spray wand in place.

CONNECTING THE HIGH PRESSURE HOSE

TO THE PUMP

See Figure 6.

After the high pressure hose has been uncoiled and attached

tothetriggerhandle:

 Pull back and hold the spring loaded collar on the

pump.

 Insert the nozzle on the end of the high pressure hose

into the collar.

 Release the collar.

 Pull on the hose to be certain it is properly secured.

CONNECTING THE GARDEN HOSE TO THE

PRESSURE WASHER

See Figure 7.

CAUTION:

Always observe all local regulations when connnecting

hoses to the water main. Some areas have restrictions

against connecting directly to public drinking water sup-

ply to prevent the feedback of chemicals into the drinking

water supply. Direct connection through a receiver tank

or backflow preventer is usually permitted.

The water supply must come from a water main. NEVER

use hot water or water from pools, lakes, etc. Before

connectingthegardenhosetothepressurewasher:

 Run water through the hose for 30 seconds to clean any

debris from the hose.

 Inspect the screen in the water intake.

 If the screen is damaged, do not use the machine until

the screen has been replaced.

 If the screen is dirty, clean it before connecting the garden

hose to the machine.

To connect the garden hose to the machine:

 Uncoil the garden hose.

NOTE: There must be a minimum of 10 feet of unre-

stricted hose between the pressure washer intake and

the hose faucet or shut off valve (such as a “Y” shut off

connector).

 With the hose faucet turned completely off, attach the

end of the garden hose to the water intake. Tighten by

hand.

ATTACHING INJECTION HOSE

See Figure 8.

Before detergent can be used with this machine, the injection

hose must be attached.

 Push the open end of the clear injection hose securely

over the fitting as shown.

 Place the filtered end of the injection hose in the bottle

of detergent.

Page 9 — English

OPERATION

WARNING:

Do not allow familiarity with this product to make you

careless. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection marked to comply with

ANSI Z87.1. Failure to do so could result in objects be-

ing thrown into your eyes, resulting in possible serious

injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this product. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Never direct a water stream toward people or pets, or

any electrical device. Failure to heed this warning could

result in serious injury.

APPLICATIONS

Youmayusethisproductforthepurposeslistedbelow:

Removing dirt and mold from decks, cement patios, and

house siding

Cleaning cars, boats, motorcycles, outdoor furniture, and

grills

ADDING/CHECKING ENGINE LUBRICANT

See Figure 9.

NOTE: This machine has been shipped with approximately

2 oz. of lubricant in the engine from testing. You must add

lubricant to the engine before starting it the first time.

CAUTION:

Any attempt to start the engine without adding lubricant

will result in engine failure.

To add engine lubricant:

 Place pressure washer on a flat, level surface.

 Unscrew the oil cap / dipstick by turning counter-

clockwise.

 Using 4-stroke engine lubricant (SAE 30 or SAE 10W30),

fill to the upper level of the oil filter neck (18 oz., 4-cycle

engine lubricant provided).

NOTE: We recommend you use ONLY Homelite or G-OIL

®

in your product.

 Replace the oil cap / dipstick and securely tighten.

NOTE: This engine has a total lubricant capacity of

0.63 qt.

To check engine lubricant level:

 Set engine on a flat surface.

 Wipe dipstick clean and re-seat in hole; do not

rethread.

 Remove dipstick again and check lubricant level. Lubricant

level should fall within the hatched area on the dipstick.

 If level is low, add engine lubricant until the fluid level

rises to the upper portion of the hatched area on the

dipstick.

 Replace and secure the oil cap/dipstick.

CAUTION:

Do not overfill. Overfilling the crankcase may cause ex-

cessive smoke and engine damage.

ADDING GASOLINE TO THE FUEL TANK

See Figure 10.

WARNING:

Gasoline and its vapors are highly flammable and

explosive. To prevent serious personal injury and prop-

erty damage, handle gasoline with care. Keep away from

ignition sources, handle outdoors only, do not smoke

while adding fuel, and wipe up spills immediately.

When adding gas to the pressure washer, make sure the unit

is sitting on a flat, level surface. If the engine is hot, let the

pressure washer cool before adding gas. ALWAYS fill the

fuel tank outdoors with the machine turned off.

NOTE: Use unleaded gas only. DO NOT mix lubricant with

gas.

 Before removing the fuel cap, clean the area around it.

Remove the fuel cap.

 Insert a clean funnel into the fuel tank then slowly

pour gasoline into the tank. Fill tank to approximately

1-1/2 in. below the top of the tank neck (this allows for

fuel expansion).

 Replace fuel cap and tighten until the cap “clicks”.

 Clean up any spills before starting the engine.

OXYGENATED FUELS

DO NOT USE E85 FUEL. IT WILL VOID YOUR WAR-

RANTY.

NOTE: Fuel system damage or performance problems re-

sulting from the use of an oxygenated fuel containing more

than the percentages of oxygenates stated previously are

not covered under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) or 15% ethanol by volume

(commonly referred to as E15) are acceptable. E85 is not.

Page 10 — English

OPERATION

STARTING AND STOPPING THE PRESSURE

WASHER

See Figures 11 - 12.

CAUTION:

Do not run the pump without the water supply connected

and turned on.

Before starting the engine:

Connect all hoses.

Check all fluids (lubricant and gas).

NOTE: The engine is equipped with a low oil sensor that

will prevent the engine from starting and/or running if

there is insufficient lubricant in the crankcase.

Turn on the garden hose then squeeze the trigger to

relieve air pressure; hold the trigger until a steady stream

of water appears.

To start the engine:

 Turn the fuel valve to the ON position.

 Move the choke lever to the CLOSED position.

NOTE: If the engine is warm, leave the choke valve in the

OPEN position.

 Move the throttle lever away from the MIN position about

a third of the way toward the MAX position.

 Put the engine switch in the ON position.

 Pull the recoil starter grip until the engine runs (a maximum

of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place.

 Allow the engine to run for 30 seconds, then push the

choke lever to the OPEN position.

To stop the engine:

Put the engine switch in the OFF position.

USING THE SPRAY WAND TRIGGER

See Figure 13.

For greater control and safety, keep both hands on the

trigger handle at all times.

 Pull back and hold the trigger to operate the pressure

washer.

 Release the trigger to stop the flow of water through the

nozzle.

To engage the lock out:

 Push up on the lock out until it clicks into the slot.

To disengage the lock out:

 Push the lock out down and into its original position.

For the most effective cleaning, the spray nozzle should be

between 8 in. and 24 in. from the surface to be cleaned. If

the spray is too close it can damage the cleaning surface.

SELECTING THE RIGHT NOZZLE FOR THE

JOB

See Figures 14 - 15.

Before starting any cleaning job, determine the best nozzle

for the job. Each of the nozzles has a different spray

pattern. The nozzle patterns are:  40º (for gentle rinse),

25º (for general purpose or large surfaces), 0º (for spot

cleaning or high-to-reach areas), and the black nozzle for

using detergent.

WARNING:

NEVER change nozzles without locking the lock out on

the trigger handle and NEVER point the wand at your

face or at others. The quick-connect feature contains

small springs that could eject the nozzle with some force.

Failure to heed this may cause personal injury.

Using the quick-connect collar, changing nozzles is easy.

To connect a nozzle to the trigger handle:

 Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Push the nozzle into the quick-connect collar until it clicks

in place and is secured properly.

To disconnect a nozzle from the trigger handle once the

cleaning job is complete:

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Remove the nozzle by placing hand over nozzle then

pulling back the quick-connect collar. Place nozzle in the

nozzle storage area on the top of the machine.

USING THE PRESSURE REGULATOR

See Figure 16.

The high pressure pump includes a feature that allows you

to adjust the pressure from a low of 300 PSI to the high-

est pressure allowed by the pressure washer. When used

at the lowest pressure, any standard quick connect nozzle

can be used.

NOTE: The trigger may need to be depressed and released

several times before the pressure will drop.

CAUTION:

Always return the regulator to the MAX pressure setting

before storing the pressure washer.

Page 11 — English

OPERATION

WASHING WITH DETERGENT

See Figure 17.

Use only detergents designed for pressure washers; house-

hold detergents, acids, alkalines, bleaches, solvents, flam-

mable material, or industrial grade solutions can damage

the pump. Many detergents may require mixing prior to use.

Prepare cleaning solution as instructed on the solution bottle.

 Install the black nozzle on the spray wand.

 Place the detergent hose into the detergent container.

Spray the detergent on a dry surface using long, even,

overlapping strokes. To prevent streaking, do not allow

detergent to dry on the surface.

Before shutting off the engine:

 Place the injection hose in a bucket of clean water.

 Flush for 1 - 2 minutes (spray clear water through the

spray wand).

 Shut off the engine.

NOTE: Shutting OFF ( O ) the engine will not relieve pressure

in the system. Pull trigger to release water pressure.

RINSING WITH THE PRESSURE WASHER

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Remove the nozzle by placing hand over nozzle then

pulling back the quick-connect collar. Place nozzle in the

nozzle storage area on the top of the machine.

 Selecttherightnozzleforthejob:

• Use medium pressure nozzle (green) for items such as

a car or boat.

• Use higher pressure nozzle for jobs such as stripping

paint and degreasing the driveway. When using these

nozzles, test a small area first to avoid surface damage.

 Start at the top of the area to be rinsed and work down,

overlapping the strokes.

MOVING THE PRESSURE WASHER

See Figure 18.

NOTE: Never lift or carry this product using the moving

handle.

 Turn the pressure washer off.

 Tilt the machine toward you until it balances on the wheels

then roll the machine to the desired position

Page 12 — English

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

WARNING:

Always wear eye protection marked to comply with ANSI

Z87.1. Failure to do so could result in objects being thrown

into your eyes, resulting in possible serious injury.

WARNING:

Before inspecting, cleaning or servicing the machine, shut

off engine, wait for all moving parts to stop, and discon-

nect spark plug wire and move it away from spark plug.

Failure to follow these instructions can result in serious

personal injury or property damage.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which may result in serious personal

injury.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an authorized service center.

Before running the engine, perform the following pre-

operationsteps:

Check that all bolts, nuts, etc., are securely tightened.

Make sure the air filter is clean.

Check both the engine lubricant level and the fuel tank

level; refill as needed.

Inspect the work area for hazards.

If there is excessive noise or vibration, stop the unit

immediately.

NOZZLE MAINTENANCE

Excessive pump pressure (a pulsing sensation felt while

squeezing the trigger) may be the result of a clogged or

dirty nozzle.

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

Remove the nozzle from the spray wand.

NOTE: Never point the spray wand at your face.

To free any foreign materials clogging or restricting the

nozzle, blow out or remove debris with a fine needle.

Using a garden hose, flush debris out of nozzle by back

flushing (running the water through the nozzle backwards

or from the outside to the inside).

Reconnect the nozzle to the spray wand.

Turn on the water supply and start the engine.

STORING THE PRESSURE WASHER

See Figure 19.

Store the pressure washer with the gas tank empty by either

draining the tank or running the pressure washer until the

gas runs out. Allow 30 minutes of “cool down” time before

storing the machine. Store in a dry, covered area where the

weather can’t damage it.

It is important to store this product in a frost-free area. Always

empty water from all hoses, the pump, and the detergent

bucket before storing.

NOTE: Use of a fuel stabilizer and pump saver will give you

better performance and increase the life of the machine.

Discharge Fuel:

Drain the fuel tank completely. Stored gas can go stale in

30 days.

Engine Lubricant:

Drain the lubricant and replace with fresh, clean lubricant.

Spark Plug:

Disconnect spark plug wire and remove the spark plug.

Pour about a teaspoon of clean, air-cooled, four-cycle

lubricant through the spark plug hole into the combustion

chamber.

Leaving the spark plug out, pull the starter cord two or

three times to coat the inside of the cylinder wall.

Inspect the spark plug and clean or replace, as neces-

sary.

Reinstall the spark plug, but leave the spark plug wire

disconnected.

Hoses and Pump:

Flush the injection hose with clean water for 1-2 minutes.

Remove all hoses. Empty the pump by pulling on the recoil

starter about 6 times. This should remove most of the liquid

from the pump.

For winterizing and long-term storage:

 Disconnect the water connection, if necessary.

 Start the pressure washer and allow it to run for a few

seconds to eliminate any water remaining in the pump.

 Coil the hoses and place in the hook-and loop strap on the

unit’s handle. Do not allow the hose to become kinked.

 Store the unit and accessories in an area that does not

reach freezing temperatures. Do not store near furnace

or other sources of heat that could dry out the pump

seals.

Page 13 — English

MAINTENANCE

CAUTION:

The use of a pump protector is recommended to prevent

cold weather damage during storage over the winter

months.

CHECKING/CLEANING AIR FILTER

See Figure 20.

A dirty air filter will cause starting difficulty, loss of perfor-

mance, and shorten the life span of the engine. Check the

air filter monthly. For best performance, replace the air filter

at least once a year.

 Remove the wing nut, then remove the air filter cover.

 Remove the second wing nut, then remove the air filter

unit.

 If the foam filter element is dirty, remove it from the air

filter unit. Clean the foam filter element with warm soapy

water. Rinse and let dry.

NOTE: If the air filter unit is dirty or damaged, it must be

replaced. If the foam filter element is damaged, it should

also be replaced.

 Apply a light coat of engine oil to the foam filter element,

then squeeze it out.

 Replace the foam filter element on the air filter unit.

 Replace the air filter unit and reinstall wing nut to se-

cure.

 Replace the air filter cover and reinstall second wing nut

to secure.

NOTE: Do not run the engine without both the foam filter

element and the air filter. Rapid engine wear will result.

PREPARING FOR USE AFTER STORAGE

Pull the recoil starter grip three or four times to clean

lubricant from the combustion chamber.

Remove spark plug from the cylinder. Wipe lubricant from

the spark plug and return it to the cylinder.

Reconnect the spark plug wire.

Refuel the machine as described earlier in the operator’s

manual.

Page 14 — English

TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

Engine fails to start 1. No fuel in tank

2. Spark plug shorted or fouled

3. Spark plug is broken (cracked

porcelain or electrodes broken)

4. Ignition lead wire shorted, broken,

or disconnected from spark plug

5. Ignition inoperative

6. Low oil

7. Pressure trapped

1. Fill tank

2. Replace spark plug

3. Replace spark plug

4. Replace lead wire or attach to spark

plug

5. Contact authorized service center

6. Add oil

7. Pull trigger to release pressure

Engine hard to start 1. Water in gasoline

2. Weak spark at spark plug

1. Drain entire system and refill with

fresh fuel

2. Contact authorized service center

Engine lacks power 1. Dirty air filter 1. Clean or replace air filter

Detergent fails to mix with spray 1. Detergent injection hose is not

properly submerged

2. High pressure nozzle attached

1. Insert injection hose into detergent

container or detergent bottle

2. Use low pressure nozzle (black) to

apply detergent

Pump doesn’t produce pressure 1. Low pressure nozzle installed

2. Inadequate water supply

3. Trigger handle or spray wand

leaks

4. Nozzle is clogged

5. Pump is faulty

6. Air in line

1. Replace with high pressure nozzle

2. Provide adequate water flow

3. Check connections and / or replace

trigger handle or spray wand

4. Clean nozzle

5. Contact authorized service center

6. Squeeze trigger on trigger handle to

remove air from line

Machine doesn’t reach high pressure 1. Diameter of garden hose is too

small

2. Water supply is restricted

3. Not enough inlet water

4. Wrong nozzle is attached

5. Pressure regulator is set to MIN

(–)

1. Replace with 3/4 in. garden hose

2. Check garden hose for kinks, leaks,

and blockages

3. Open water source full force

4. Attach the high pressure nozzle

5. Adjust pressure regulator to MAX (+)

Page 15 — English

WARRANTY

LIMITED NON-ENGINE WARRANT Y

STATEMENT

Homelite Consumer Products warrants to the original retail

purchaser that this HOMELITE brand pressure washer is

free from defect in material and workmanship and agrees

to repair or replace, at Homelite Consumer Products’s

discretion, any defective product free of charge within

these time periods from the date of purchase.

 Threeyearsiftheproductisusedforpersonal,family

or household use;

 Oneyear,ifanyoftheaboveproductsareusedforany

other purpose, such as commercial or rental.

This warranty extends to the original retail purchaser

only and commences on the date of the original retail

purchase.

Any part of the this product manufactured or supplied by

Homelite Consumer Products and found in the reasonable

judgment of Homelite Consumer Products to be defective

in material or workmanship will be repaired or replaced

without charge for parts and labor by a Homelite authorized

service center.

The product, including any defective part, must be returned

to a Homelite authorized service dealer within the warranty

period. The expense of delivering the product to the dealer

for warranty work and the expense of returning it back to

the owner after repair or replacement will be paid by the

owner. Homelite Consumer Products’ responsibility in

respect to claims is limited to making the required repairs

or replacements and no claim of breach of warranty shall

be cause for cancellation or rescission of the contract of

sale of any HOMELITE brand product. Proof of purchase

will be required by the dealer to substantiate any warranty

claim. All warranty work must be performed by a Homelite

authorized service center.

This warranty is limited to one year from the date of original

retail purchase for any HOMELITE brand pressure washer

that is used for rental or commercial purposes, or any other

income-producing purpose.

This warranty does not cover any product that has been

subject to misuse, neglect, negligence, or accident, or that

has been operated in any way contrary to the operating

instructions as specified in the Homelite Consumer

Products operator’s manual. This warranty does not apply

to any damage to the product that is the result of improper

maintenance or to any product that has been altered or

modified so as to adversely affect the products operation,

performance or durability or that has been altered or

modified so as to change its intended use. The warranty

does not extend to repairs made necessary by normal

wear or by the use of parts or accessories which are either

incompatible with the HOMELITE brand pressure washer or

adversely affect its operation, performance or durability.

Inaddition,thiswarrantydoesnotcover:

A. Tune-ups – Air filters, gas filters, spark plugs

B. Wear items – Hoses, connector fittings, spray nozzles,

wheels, spray wand, detergent bucket, detergent

tank

Homelite Consumer Products reserves the right to change

or improve the design of any HOMELITE brand pressure

washer without assuming any obligation to modify any

product previously manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION

TO THE STATED WARRANTY PERIOD. ACCORDINGLY,

ANY SUCH IMPLIED WARRANTIES INCLUDING

MERCHANTABILITY, FITNESS FOR A PARTICULAR

PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN

THEIR ENTIRETY AFTER THE EXPIRATION OF THE

APPROPRIATE THREE-YEAR OR ONE-YEAR, WARRANTY

PERIOD. HOMELITE CONSUMER PRODUCTS’S

OBLIGATION UNDER THIS WARRANTY IS STRICTLY

AND EXCLUSIVELY LIMITED TO THE REPAIR OR

REPLACEMENT OF DEFECTIVE PARTS AND HOMELITE

CONSUMER PRODUCTS DOES NOT ASSUME OR

AUTHORIZE ANYONE TO ASSUME FOR THEM ANY

OTHER OBLIGATION. SOME STATES DO NOT ALLOW

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY

LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO

YOU. HOMELITE CONSUMER PRODUCTS ASSUMES NO

RESPONSIBILITY FOR INCIDENTAL, CONSEQUENTIAL

OR OTHER DAMAGES INCLUDING, BUT NO LIMITED

TO EXPENSE OF RETURNING THE PRODUCT TO

AN AUTHORIZED HOMELITE SERVICE CENTER AND

EXPENSE OF DELIVERING IT BACK TO THE OWNER,

MECHANIC’S TRAVEL TIME, TELEPHONE OR TELEGRAM

CHARGES, RENTAL OF A LIKE PRODUCT DURING THE

TIME WARRANTY SERVICE IS BEING PERFORMED,

TRAVEL, LOSS OR DAMAGE TO PERSONAL PROPERTY,

LOSS OF REVENUE, LOSS OF USE OF THE PRODUCT,

LOSS OF TIME, OR INCONVENIENCE, SOME STATES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF

INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE

ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY

TO YOU.

This warranty gives you specific legal rights, and you may

also have other rights which vary from state to state.

This warranty applies to all HOMELITE brand pressure

washer distributed by Homelite Consumer Products and

sold in the United States, Mexico, and Canada.

To locate your nearest Homelite authorized service

center, dial 1-800-242-4672 or log on to our website at

www.homelite.com.

Page is loading ...

Page 16 — EnglishPage 16

NOTES / NOTAS

Page 17 — EnglishPage 17

NOTES / NOTAS

3100 PSI PRESSURE WASHER

NETTOYEUR HAUTE PRESSION DE 3 100 PSI

LAVADORA A PRESIÓN DE 3 100 PSI

HL80923

HOMELITE CONSUMER PRODUCTS, INC.

1428 Pearman Dairy Road, Anderson, SC 29625

1-800-242-4672•www.homelite.com

987000-556

5-6-09(REV:00)

WARNING:

The engine exhaust from this product

contains chemicals known to the

State of California to cause cancer,

birth defects, or other reproductive

harm.

CALIFORNIA PROPOSITION 65

SERVICE

For parts or service, contact your nearest Homelite authorized service dealer.

Be sure to provide all relevant information when you call or visit. For the loca-

tion of the authorized service dealer nearest you, please call 1-800-242-4672

or visit us online at www.homelite.com.

REPAIR PARTS

The model number of this product is found on a plate or label attached to the

housing. Please record the serial number in the space provided below.

MODEL NO. _________________________________

SERIAL NO. _________________________________

DÉPANNAGE

Pour tout entretien ou réparation du produit, contacter le centre de réparations

Homelite agréé le plus proche. Veiller à fournir toutes les informations pertinentes

lors de tout appel téléphonique ou visite. Pour obtenir l’adresse du centre de

réparations agréé le plus proche, téléphoner au 1-800-242-4672, ou visiter

notre site www.homelite.com.

PIÈCES DE RECHANGE

Le numéro de modèle se trouve sur une plaquette ou étiquette placée sur le

bâti. Noter le numéro de série dans l’espace ci-dessous.

NUMÉRO DE MODÈLE ______________________

NUMÉRO DE SÉRIE _________________________

SERVICIO

Para obtener piezas o servicio, comuníquese con el centro de servicio

autorizado de Homelite más cercano. Asegúrese de proporcionar todos los

datos pertinentes al llamar o al presentarse personalmente. Para obtener

información sobre el establecimiento de servicio autorizado más cercano a

usted, le suplicamos llamar al 1-800-242-4672 o visitar nuestro sitio en la red

mundial, en la dirección www.homelite.com.

PIEZAS DE REPUESTO

El número de modelo de este producto se encuentra en una placa o etiqueta

pegada a la caja del motor. Le recomendamos anotar el número de serie en

el espacio suministrado abajo.

NÚMERO DE MODELO ______________________

NÚMERO DE SERIE _________________________

AVERTISSEMENT :

Les gaz d’échappement de ce produit

contiennent des produits chimiques

identifiés par l’état de Californie comme

causes de cancer, de malformations

congénitales et d’autres troubles de

l’appareil reproducteur.

PROPOSITION

65 DE L’ÉTAT DE

CALIFORNIE

ADVERTENCIA:

Las emanaciones provenientes del

escape del motor de este producto

contienen sustancias químicas

reconocidas por el estado de California

como causantes de cáncer, defectos

congénitos y otras afecciones del

aparato reproductor.

CALIFORNIA - PROPUESTA DE LEY

NÚM.

65

OPERATOR’S MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

HL80923

Homelite HL80923 User manual

Homelite HL80923 User manual

in other languages

Related papers

Other documents