INSTALLATION
INSTRUCTIONS
REAR
A-ITACHMENT
HITCH
MFG. NO. 1692010
INSTALLATION
Nate: Electric Lift Kit (1692032) must be installed on 14GTG/
1714G tractors for all rear-mounted attachments.
Rear hitch required for mounting tiller to 14GTG/
IGGTH/1700 Series tractors attachment.
1. Install the upper hitch assembly (A, figure 1) to the rear
tractor frame using four spacers (B), washers
(C)
and
1/2-13x 2 l/2” capscrews (D). Secure on inside of frame
with
l/213
nyloc nuts. The front capscrews are mounted
in the top frame holes and the
rear
capscraws are
mounted in the bottom frame holes as shown in figure
1.
2. Install the lower hitch assembly (E) to the tractor drawbar
(F)
using two
1/2-13x
1 l/2” capscrews (G) and two i/2-
13
nyloc
nuts.
Secure the lower hitch brace to the rear frame using two
5/i
6-18 x
1”
capscrews (H) and two
5/l
6 locknuts.
3. After the electric lift is installed, the lift rod (A, figure 2) will
be installed to the upper hitch as shown in figure
1
and to
the lift arm assembly using a
clevis
pin (B) and safety clip
(C) as shown in figure 2.
Note: If tire chains are to be used for tiller operation, rear
wheels should be inverted for additional clearance between
RH wheel/chain and tiller lift rod.
FIGURE 2. Electric Lift
A. Lift Rod
B. Clevie Pin
FIGURE 1. Rear Hitch
A. Upper Hitch Assembly
6.
Spacers
C. Washers
D. Capscrews,
112-13
x 2 l/2”
E. Lower
Hitch
Assembly
F.
Drawbar
G. Capscrews, 1/2-13x
1
l/2”
H. Capscrews, 5116-l 8 x 1”
C. Safety Clip
Form 1707679
Printed in USA
a/91
INSTALLATION
Note: Electric
Lift
Kit (1692032) must be installed on 14GTG/
1714G tractors for all rear-mounted attachments.
1. Install the upper hitch assembly (A, figure 1) to the rear
tractor frame using four spacers (B), washers (C) and
1/2-13x
2
l/Z”
capscrews (D). Secure on inside of frame
with
112-l
3 nyloc nuts. The front
capscrews
are mounted
in the top frame holes and the rear
capscrews
are
mounted in the bottom frame holes as shown in figure 1.
2. Install the lower hitch assembly (E) to the tractor drawbar
(F)
using two 1/2-l 3 x
1
i/2” capscrews (G) and two i/2-
13 nyloc nuts.
Secure the lower hitch brace to the rear frame using two
5/l
6-I
8 x
1”
capscrews (H) and two
5/i
6 locknuts.
3. After the electric
lift
is installed, the
lift
rod (A, figure 2) will
be installed to the upper
hitch
as shown in figure
1
and to
the
lift
arm assembly using a
clevis
pin (6) and safety clip
(C) as shown in figure 2.
Note: If tire chains are to be used for tiller operation, rear
wheels should be inverted for additional clearance between
RH
wheeljchain and tiller Iii rod.
INSTALLATION
INSTRUCTIONS
REAR ATTACHMENT HITCH
MFG. NO. 1692010
Rear hitch required for mounting tiller to
14GTG/
16GTH/1700 Series tractors attachment.
FIGURE 2. Electric Lift
A. Lift Rod
B. Clevis Pin
C. Safety Clip
FIGURE 1. Rear
Hitch
A. Upper Hitch Assembly
B. Spacers
C. Washers
D. Capscrews,
11’2-13
x 2 l/2”
E. Lower Hitch Assembly
F.
Drawbar
G. Capscrews,
112-13
x 1
112”
H.
Capscrews,
5/16-18x 1”
Form 1707679
Printed in USA
s/91
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Snapper 1694151 User manual
-
-
-
-
-
-
-
-
-
Other documents
-
Simplicity 1691526 User manual
-
-
-
-
-
Simplicity 1694397 User manual
-
-
-
-