Bosch ER726RT71E/01 User manual

1

bitte aufbewahren

veuillez conserver

si prega di conservarle

please keep

por favor, guardar

lütfen saklayýnýz

Assembly instructions

Einbauanleitung

Notice de montage

Istruzioni di Montaggio

Instrucciones de montaje

пожалуйста, сохраните данное руководство

Montaj talimatlarý

Руководство по монтажу

s.v.p. bewaren

Installatievoorschrift

~

.

-

.

29

19

~26

~50

520 ÷ 546

en

de

fr

it

es

pt

nl

tr

ru

Instruções de montagem

Page is loading ...

en

Read the appliance's instructions before

installing and using.

The graphics in these Assembly

instructions are given as a guide only.

The manufacturer is exempt from all

liability if this manual's requirements

are not complied with.

Safety instructions

All operations relating to installation,

regulation and conversion to other

types of gas must be carried out by

an authorised installation engineer,

respecting applicable regulations,

standards and the specifications of

the gas and electricity providers.

Before you begin, turn off the

appliance's electricity and gas

supply.

You are recommended to contact the

Technical Assistance Service to

convert to another type of gas.

This appliance has been designed for

home use only, not for commercial or

professional use. This appliance cannot

be installed on yachts or in caravans.

The warranty will only be valid if the

appliance is used for the purpose for

which it was designed.

Before installing, you need to check that

local distribution conditions (gas type

and pressure) and the appliance's

adjustment are compatible (see table I).

The appliance's adjustment conditions

are written on the label or the

specifications plate.

This appliance can only be installed in a

well-ventilated place in accordance with

existing regulations and ventilation

specifications. The appliance must not

be connected to a combustion product

evacuation device.

The supply cable must be attached to

the unit to prevent it from touching hot

parts of the oven or hob.

Appliances with electrical supply must

be earthed.

Do not tamper with the appliance's

interior. If necessary, call our Technical

Assistance Service.

Before installing

This appliance is class 3 type, according

to the EN 30-1-1 regulation for gas

appliances: built-in appliance.

The units next to the appliance must be

made of non-inflammable materials. The

laminated covering and glue for

adhering it must be heat resistant.

This appliance cannot be installed

above fridges, washing machines,

dishwashers or similar.

The hob may only be fitted above a

ventilated oven.

If an oven is installed underneath the

hob, the thickness specified for the work

surface may exceed the minimum

thickness stated in these instructions.

If an extractor fan is installed, you must

follow the installation manual's

instructions, always keeping a minimum

distance of 650 mm to the hob.

Preparation of unit (fig. 1-2)

Make a cut of an appropriate size in the

work surface.

If the hob is electric or mixed (gas and

electricity) and there is no oven below,

place a non-inflammable separator

(e.g.metal or plywood) 10 mm from the

bottom of the hob. This will prevent

access to the base of the hob. If the hob

is gas, it is recommendable to place the

separator at the same distance.

On wooden work surfaces, varnish the

cutting surfaces with a special glue to

protect them from moisture.

Installation of appliance

Note: Wear protective gloves to fit the

hob.

The clips and the adhesive seal

(underside of the hob) are factory-fitted,

do not under any circumstances remove

them. The seal ensures that the entire

work surface will be watertight, and

prevents water seepage. In order to fit

the appliance into the kitchen unit, first

place the hob in the correct position then

loosen each of the clips so that

they all turn freely (it is not necessary to

completely undo them). Fit and centre

the hob.

Press the sides of the hob until it is

supported around its entire perimeter.

Turn the clips and tighten them fully. The

screws for the clips must be vertical to

the base of the housing. Fig. 3.

Removing the hob

Turn off the electricity and gas supply to

the appliance.

Unscrew the clips and proceed in the

reverse order to installation.

Gas connection (fig. 4)

The end of the inlet connection point of

the gas hob has a 1/2” (20.955 mm)

thread that allows for:

- rigid connection.

- connection using a flexible metal hose

(L min. 1 m - max. 3 m). With this option,

you must prevent the hose from coming

into contact with the moving parts of the

kitchen unit (for example, a drawer) or

accessing any spaces which might

become obstructed.

If you need to make a cylindrical

connection, replace the factory-fitted L-

tube with the one in the accessory bag.

Fig. 4a.

Please remember to insert the seal.

Warning! If any connection is handled,

check for tightness. Danger of leaks.

The manufacturer shall not be held liable

if any connection should leak, after

being handled.

Electric connection (fig. 5)

Check the voltage and power of the

appliance are compatible with the

electrical installation.

The hobs are supplied with a power

cable with or without a wall socket plug.

Provide an omnipolar cut-off switch with

a minimum contact gap of 3 mm (except

for plug connections, if the user has

access to it).

Appliances with plugs must only be

connected to sockets that have earth

wires correctly installed.

This appliance is type “Y”: the input

cable can only be changed by the

Technical Assistance Service and not

the user. The cable type and minimum

cross-section must be respected.

Changing the gas type

If the country’s regulations permit, this

appliance can be adapted to other types

of gas (see specifications plate). The

components necessary for this are in the

transformation kit supplied (according to

model). The kit is also available from our

Technical Assistance Service. The

following steps should be taken:

A) Changing the nozzles of the rapid,

semi-rapid and auxiliary burners of

the hob (fig. 6):

- Remove the pan supports, burner

covers and diffusers.

- Change the nozzles using the spanner

provided by our Technical Assistance

Service (code 424699), taking special

care to ensure that the nozzle does not

fall when it is removed from or fitted to

the burner.

Ensure that they are completely

tightened to guarantee the seal. Primary

air adjustment is not necessary with

these burners.

B) Changing the nozzles for double-

flame burners (fig. 7):

The glass panel and frame are fixed to

the rest of the hob using a clip mounting

system. The following steps must be

taken to remove the glass panel and

frame:

- Remove all the burner covers and pan

supports. Fig. 7a.

- Loosen the screws on the burners, fig.

7b-7c, and remove the control knobs

from their respective housings.

Use the disassembly lever 483196

available from our Technical Assistance

Service. To release the front clips, apply

the lever in the area shown in figures 8

according to the hob model.

Never use the lever on glass edges

which have no profile or frame!

- To release the rear clips, carefully raise

the entire glass panel and frame, as in

fig. 8a.

Changing the outer flame nozzle

(fig. 9a):

- Loosen the clamp screw to release the

bushing by moving it backwards to

access the main nozzle easily. Fig. a1.

- Remove the outer flame nozzle by

turning it towards the left. Fig. a2-a3.

- Screw in the new outer flame nozzle.

Fig. a3-a4, as in table II.

- Adjust the distance of the airflow

adjusting bushing L2 according to the

value -Z- shown in table II. Fig. a5.

- Tighten the clamp screw. Fig. a6.

Changing the inner flame nozzle

(fig. 9b):

- Unscrew the part M3 from the threaded

part M2; to do this, hold the threaded

part in the opposite direction.

- Remove the pipe from the M2 part. Fig.

b2.

- Disassemble parts M2 and M4 from

part M1. Fig. b3-b4.

- Remove the inner flame nozzle M4

from part M2. Fig. b5-b6.

- Screw in the new inner flame nozzle

M4, according to table II. Fig. b6-b7.

Page is loading ...

I

COUNTRIES/GASES GAS ADJUSTED MODEL TYPE

Qn G30, G31,

G20, G25,

G110 (kW)

Qn

G25.1

(kW)

G20

(m3/h)

G25

(m3/h)

G25.1

(m3/h)

G30

(g/h)

G31

(g/h)

G110

(g/h)

WV~Hz

ER626PB70N HSE-K6F4030 7,70 - 0,734 0,854 - 559 550 - 0,8 W 220-240 V~ 50/60 Hz

ER726RB71N HSE-K7F4V30 11,90 - 1,134 1,319 - 864 849 - 0,8 W 220-240 V~ 50/60 Hz

PRP626B70N HSE-K6F4030 7,70 - 0,734 0,854 - 559 550 - 0,8 W 220-240 V~ 50/60 Hz

ER626PF70E HSE-K6F403F 7,70 7,70 0,734 0,854 0,852 559 550 - 3,00 W 220-240 V~ 50/60 Hz

ER626PT70E HSE-K6F403M 7,70 7,70 0,734 0,854 0,852 559 550 - 3,00 W 220-240 V~ 50/60 Hz

ER626YB70E HSE-K6F3S30 5,80 5,80 0,553 0,643 0,642 421 414 - 1800 W 220-240 V~ 50/60 Hz

ER726RB71E HSE-K7F4V30 11,90 11,70 1,134 1,319 1,295 864 849 - 0,8 W 220-240 V~ 50/60 Hz

ER726RF71E HSE-K7F4V3F 11,90 11,70 1,134 1,319 1,295 864 849 - 3,00 W 220-240 V~ 50/60 Hz

ER726RT71E HSE-K7F4V3M 11,90 11,70 1,134 1,319 1,295 864 849 - 3,00 W 220-240 V~ 50/60 Hz

GK51TG HSE-K7F4V30 11,90 - 1,134 1,319 - 864 849 - 0,8 W 220-240 V~ 50/60 Hz

PRP626F70E HSE-K6F403F 7,70 7,70 0,734 0,854 0,852 559 550 - 3,00 W 220-240 V~ 50/60 Hz

PRP626M70E HSE-K6F4030 7,70 7,70 0,734 0,854 0,852 559 550 - 0,8 W 220-240 V~ 50/60 Hz

PRR726F71E HSE-K7F4V3F 11,90 11,70 1,134 1,319 1,295 864 849 - 3,00 W 220-240 V~ 50/60 Hz

PRY626B70E HSE-K6F3S30 5,80 5,80 0,553 0,643 0,642 421 414 - 1800 W 220-240 V~ 50/60 Hz

ER626PB70E HSE-K6F4030 7,70 7,70 0,734 0,854 0,852 559 550 1,753 0,8 W 220-240 V~ 50/60 Hz

GK41TG HSE-K6F4030 7,70 - 0,734 0,854 - 559 550 1,753 0,8 W 220-240 V~ 50/60 Hz

PRP626B70E HSE-K6F4030 7,70 7,70 0,734 0,854 0,852 559 550 1,753 0,8 W 220-240 V~ 50/60 Hz

ER626PB70D HSE-K6F4030 7,70 7,70 0,734 0,854 0,852 559 550 - 0,8 W 220-240 V~ 50/60 Hz

ER726RF71D HSE-K7F4V3F 11,90 11,70 1,134 1,319 1,295 864 849 - 3,00 W 220-240 V~ 50/60 Hz

Σ Σ

NL

Cat.

II

2L3B/P

25-30

p(mbar)

Cat.

II

2E+3+

2H3B/P

20-50

20/25-28-30/37

AT

II

2H3B/P

20-30

LU

I

2E

20

II

2H3+

IT/PT

20-30/37

LV

I

2H

20

II

ES/GB/GR/IE

II

2H3+

20-28/37

PL

20-37

DE

II

2ELL3B/P

20-50

2E3P(B/P)

BE/FR

DK/FI/SE/CZ/SK/EE/LT/SI/RO/BG/NO/CY

p(mbar)

BE/FR

Cat.

II

2E+3+

20-50

AT

II

2H3B/P

20-30

II

2H3+

IT/PT

LV

I

2H

20

DE

20-50

II

2H3+

20-28/37

III

1a2H3B/P

DK

8-20-30

III

1ab2H3B/P

SE

8-20-30

ES/GB/GR/IE

FI/CZ/SK/EE/LT/SI/RO/BG/NO/CY

PL

I

20

2E

LU

20-37

20/25-28-30/37

II

20-30/37

II

2H3B/P

2ELL3B/P

2E3P(B/P)

p(mbar)

Cat.

II

2E+3+

2H3B/P

20-50

20/25-28-30/37

I

2E

20

AT

II

2H3B/P

20-30

ES/GR

II

2H3+

IT/PT

II

20-30/37

LV

I

2H

20

2ELL3B/P

II

20-28/37

20-50

PL

2H3+

20-37

2E3B/P

II

LU

BE/FR

DK/FI/SE/CZ/SK/EE/LT/SI/RO/BG/NO/CY

DE

p(mbar)

AARDGAS G25/25 mbar

G-20/20 mbar ERDGAS / ERDGAS E /

NATURGAS / GAS NATURAL /

MAAKAASU NATURGAS / Φυοικ_αεοιο /

NATURAL GAS / GAS METANO / GAS

NATUREL / GAZ ZIEMNY

G-20/G-25-20/25 mbar AARDGAS / GAZ

NATUREL LACQ

G-20/20 mbar ERDGAS / ERDGAS E /

NATURGAS / GAS NATURAL /

MAAKAASU NATURGAS / Φυοικ_αεοιο /

NATURAL GAS / GAS METANO / GAS

NATUREL / GAZ ZIEMNY

G-20/G-25-20/25 mbar AARDGAS / GAZ

NATUREL LACQ

G-20/20 mbar ERDGAS / ERDGAS E /

NATURGAS / GAS NATURAL /

MAAKAASU NATURGAS / Φυοικ_αεοιο /

NATURAL GAS / GAS METANO / GAS

NATUREL / GAZ ZIEMNY

G-20/G-25-20/25 mbar AARDGAS / GAZ

NATUREL LACQ

II

III

Cod. 9000818475 I

G20/20 G20/25 G25/20 G25/25 G25.1/25 G30/29 G30/37 G30/50 G31/37 G110-G120/8

G20/20 DDD D ACCA B

G20/25 DDDDACCAB

G25/20 DD D D ACCA B

G25/25 DDD D ACCA B

G25.1/25 DDDD ACCA B

G30/29 BBBB B CCD B

G30/37 CCCC C C CC C

G30/50 CCCC C CC C C

G31/37 BBBB B DCC B

G110-G120/8 BBBB B ACCA

gas mbar

Qn

(kW)

m3/h g/h

distancia

casquillo

distancia

casquillo

"Z" (mm) "Y" (mm)

G20 20 72 1,1 0,105 - - - 27

G20 25 65 1,1 0,105 - - - 27

G25 20 79 1,1 0,122 - - - 27

G25 25 78 1,1 0,122 - - - 27

G25.1 25 78 1,1 0,122 - - - 27

G30 29 53 1,1 - 80 - - 27

G30 37 53 1,1 - 80 - - 28

G30 50 48 1,1 - 80 - - 24

G31 37 53 1,1 - 79 - - 27

G110 G120 8 149 1,1 0,25 - - - 27

G20 20 125 2,8 0,267 - - - 39

G20 25 109 2,8 0,267 - - - 39

G25 20 141 2,8 0,31 - - - 39

G25 25 118 2,8 0,31 - - - 39

G25.1 25 118 2,8 0,31 - - - 39

G30 29 83 2,8 - 203 - - 39

G30 37 82 2,8 - 203 - - 37

G30 50 74 2,8 - 203 - - 33

G31 37 83 2,8 - 200 - - 39

G110 G120 8 278 2,8 0,638 - - - 39

G20 20 93 1,9 0,181 - - - 29

G20 25 91 1,9 0,181 - - - 29

G25 20 105 1,9 0,211 - - - 29

G25 25 104 1,9 0,211 - - - 29

G25.1 25 104 1,9 0,21 - - - 29

G30 29 70 1,9 - 138 - - 29

G30 37 68 1,9 - 138 - - 28

G30 50 60 1,9 - 138 - - 25

G31 37 70 1,9 - 136 - - 29

G110 G120 8 220 1,9 0,433 - - - 29

G20 20 141 4,2 0,4 - 7,5 - -

G20 20 58 - - - - open 28

G20 25 132 4,2 0,4 - 3 - -

G20 25 54 - - - - 4,5 28

G25 20 156 4,2 0,466 - 1,5 - -

G25 20 63 - - - - 3,5 28

G25 25 145 4,2 0,466 - 2 - -

G25 25 60 - - - - 3 28

G25.1 25 145 4 0,443 - 2 - -

G25.1 25 60 - - - - 3 28

G30 29 96 4,2 - 305 6,5 - -

G30 29 39 - - - - open 28

G30 37 88 4,2 - 305 5 - -

G30 37 37 - - - - 5 29

G30 50 79 4,2 - 305 6,5 - -

G30 50 35 - - - - 3 26

G31 37 96 4,2 - 300 6,5 - -

G31 37 39 - - - - open 28

Bosch ER726RT71E/01 User manual

Bosch ER726RT71E/01 User manual

in other languages

Related papers

Other documents