Sony KDL-40XBR4 Owner's manual

Brand: Sony

Model: KDL-40XBR4

Category: LCD TVs

Type: Owner's manual

This manual is also suitable for

Operating Instructions

KDL-40XBR4

KDL-46XBR4

KDL-52XBR4

KDL-40XBR5

KDL-46XBR5

KDL-52XBR5

BRAVIA

Owner's Record

The model and serial nunlbers my located

at tile rear of the TV. Record ttlese

numbers in tile spaces provided below.

Relcr to diem whenever you call upon

your Sony dealer regarding this TV.

Model Name

Serial No.

WARNING

To reduce die risk ot fire or electric shock, do

not expose this TV to rain or moisture.

/_ This synlbol is intended to alert

the user to tile presence ol

uninsulated 'dangerous vohage"

widlin tile TV's enclosure that

may be of sufficient nlagnimde to

constitute a risk of electric shock

to persons.

/_ This synlbol is intended to alert

tile user to tile presence of

ilnl)ortanl operadllg and

lnaintenance (servicing)

instructions in the literature

accompanying file TV.

The TV shall not be exposed to dripping or

splaslling and no objects tilled with liquids,

such as vases, shall be i?laced on the TV.

CAUTION

To pl'e_enl eleclric shock, do not use lhis

pohu'ized AC phlg with an extension cord,

receplacle or other oullet unless tile blades can

be lhlly inserted to prevenl blade exposure.

Declaration of Conformity

Trade Nanle: SONY

Model: KDL-40XBR4/KDL-46XBR4/

KDL-52XBR4/KDL-40XBR5/

KDL-46XBR5/KDL-52XBR5

Responsible Party: Sony Electronics Inc.

Address: 16530 Via Esprillo.

San Diego, CA 92127 U.S.A.

Telephone Number: 858-942-2230

This dcvice complies wifl/part 15 of tile

FCC rules. Operation is subjecl to tile

lollowing two conditions: (1) This device

may nol cause harmfifl interlcrence, and (2)

dlis device lnust accept any interlcrence

received, including interlcrence that nlay

cau_ undesired operation.

NOTIFICATION

Tilts equipment hasbecn tested andlkmnd to

comply with dm limits lor a Class B digital

device, pursuant to Part 15 of tile FCC Rules.

These limits are designed to provide

reasonable protection against hamllhl

interlcrence in a rt:sidential installation. This

equipment generates, u_s and can radiate

radio IYcquency energy and. if not installed and

used in accordance with the instructions, nlay

cau_ h_wnllhl inlerlcrence lo radio

conltnunicalions.

However, there is no guarante_ lbat

interlPrence will not occur in a particular

installation. If this equipment does cause

harnlhd interl_zrence to radio or television

reception, which can be deternlined by turning

the equipnlent ol1 and on, the user is

encouraged lo try to correct the interfi:rence by

one or IIl()l't2 of tile l_lllowing nleasurcs:

[] Reorient or relocate the receiving antenna.

[] Increase file separation between tile

equipnlent and receiver.

[] Connect die equipment into all outlet on a

circuit dillcrcnt h'om thin to which the

receiver is conllected.

[] Consuh the dealer or an experienced radio/

TV technician Ior help.

Pursuant to FCC regulations, you arm

cautioned thai any cllanges or modifications

not expressly approved in this manual could

void your authority to operate this

equi pnlent.

Safety

[] Operate the TV only on 120-240VAC.

[] Use the AC I)ower cord specified by Sony

and suilable lbr tile vohage whcrc you use

it.

[] The plug is designed, liar salcly purposes.

lo fil into the wall outlet only one way. If

you arc unable to insert the plug fiflly inlo

the out]el, contact your dealer.

[] If any liquid or solid object should hdl

inside die cabinet, unplug the TV

imnlediately and have it checked by

qualified service personnel belbre

operating it lhrther.

[] If you will not be using file TV lor several

days. disconnect the power by pulling file

plug il_lf. Ncver pull on tile cord.

[] For details concerning salPly precautions,

see ']nll)orlanl Salcly Instruclions" on

page 4.

Installing

[] The TV should be installed nero ml easily

accessible power outlet.

[] To prevent internal heat buildup, do not

block tile ventilation openings.

[] Do not install the TV in a hot or hunlid

place, or in a place sut_iect to excessive

dust or mechanical vibration.

[] Avoid operating the TV at temperatures

below 4I°F (5°C).

[] Ifthe TV is transported directly li-om a cold

lO a warnl localion, or if tile roonl

temperature changes suddenly, the picture

nlay be blurred or show poor color due to

nloisture condensation. In this case, please

wait a low hours to let tile moisture

evaporate belbre turning on the TV.

[] To obtain file best picture, do not expo_

tile screen to direct ilhmlination or direct

sunlight. It is rcconmlcnded to use spot

lighting directed down honl tile ceiling or

to cover file windows that lhce tile screen

with opaque drapery. It is desirable to

install the TV in a roonl where tile floor and

walls arc not of a rcfleclive nlaleriah

CAUTION

Use tile lbllowing Sony TVs only with tile

Iollowing WALL-MOUNT BRACKET or

TV-stand.

SU-WL500

RHT-G800

I_H._l*nn_AISU-FL300M

SU-FL300M_ SU-FL300L

Use with other WALL-MOUNT BRACKET

or TV-sland nlay cause instability and possibly

r_2sul[ ill injury.

To Customers

Sul]icient expertise is required lbr installing

the specified TV. Be sure to subcontract the

install_aion 1oSony dealers or licensed

contractors and pay adequate allenlion lo

salcty during the installation.

Note

Tilts telcvision includes a QAIvl demodulator

wlfich should allow you to recei_ e

unscrambled digilal cable television

i)rogramming via subscription selvice to a

cable service provider. Availability of digital

cable television progranmling in your area

depends on the type of programming and signal

provided by your cable service provider.

Trademark Information

Macintosh is a trademark ol Apple Inc.,

registered in file U,S. and (>tiler countries.

HDML tile HDMI logo and High-Definition

Muhinlcdia lnterli_ce armtrademarks or

registered tradenlarks of HDMI Licensing

LLC,

Manu£,ctured under license l_'om Dolby

Laboratories. 'Dolby" and the double-D

synlbol armtradenlarks of Dolby Laboralories.

Blu-ray Disc is a trademark.

'BRAVIA" and BRAVIA+ Motionflow,

S-Force, BRAVIA Theatre Sync, IN, DMe x

and "x.v. Color" armtradelnarks or registered

nlarks of Sony Corporatkm.

'XMB" and 'xross nlcdia bar" are the

lrademarks of Sony Corporation and Sony

('Oll/I)uter Enlertainlnenl Inc.

"PLAYSTATION" is a registered trademark

and 'PS3" is a trademark of Sony Computer

Enlertainnlenl lnc.

Adobe is a registered trademark or a tradenlark

of Adobe Systems Incorporated ill United

States and/or other countries.

1411::::lliTII

DIGITAL

Important Safety Instructions ............................ 4

The Four Steps to Full HD Experience: Set,

Sound, Source, and Setup ............................ 8

Picture Quality and Aspect Ratio ....................... 8

TV Home Menu: XMB,M (Xross Media Bar) ........ 9

Using Other Equipment with Your Remote

Control .......................................................... 28

Using P&P and PIP Features ............................ 31

To Display the Sub Window ......................... 31

To Change Inputs or Channels in the

Window ..................................................... 31

To Change the Window Size of P&P ............ 31

To Exit from P&P and PIP ............................ 31

1. Installing the TV ............................................. 10

Preventing the TV from Toppling Over ......... 10

Preparation for Wall-Mounting ...................... 10

2. Locating Inputs and Outputs ....................... 11

Left Side ....................................................... 11

Rear .............................................................. 12

3. Connecting the TV ......................................... 14

Cable System or VHF/UHF Antenna

System ...................................................... 14

Cable System and VHF/UHF Antenna

System ...................................................... 14

HD Cable Box/HD Satellite Box .................... 14

PC................................................................. 16

Other Equipment .......................................... 17

Using HDMI Control for BRAVIA Theatre

Sync TM ....................................................... 18

Bundling the Connecting Cables .................. 18

4. Setting Up the Channel List

- Initial Setup ............................................... 19

Remote Control and TV Controls/

Indicators ..................................................... 20

Inserting Batteries into the Remote

Control ....................................................... 20

Remote Control and TV Controls ................. 20

Indicators ...................................................... 25

Programming the Remote Control ................... 26

Operating Sony Brand Video Equipment ......26

Programming Non-Sony Video Equipment....26

Adjusting TV Settings ................................. 32

Watching TV ................................................. 32

"_Accessing the Equipment Connected to

Your TV ......................................................... 32

Navigating through TV Home Menu on

XMB .............................................................. 33

TV Setting Description ...................................... 34

Product Support ...................................... 34

%_Clock/Timers Settings ............................. 34

_3 Picture Settings ...................................... 34

o_ Sound Settings ....................................... 36

Screen Settings ...................................... 37

o_ Video Options Settings ........................... 39

%,_Audio Options Settings ........................... 40

_c_Channel Settings .................................... 40

Closed Captions (CC) Settings ............... 41

•-_ Parental Lock Settings ............................ 42

External Inputs Settings .......................... 44

HDMI Settings ........................................ 44

General Settings ..................................... 44

_23Initial Setup ............................................. 45

Cleaning ............................................................. 46

Troubleshooting ................................................ 46

Specifications .................................................... 49

Index ................................................................... 51

Quick Setup Guide (separate volume)

Provides a variety of optional equipment

connection diagrams.

Customer Support

http://www.sony.com/tvs upport

On-line Registration

United States

http://productregistration.sony.com

Canada

http://www.SonyStyle.ca/registration

Important

Safety

Instructions

1 _ Readthese instructions

2) Keep these instructions.

3 _ Heed all warnings.

4) Follow all instructions.

5 b Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block arly ventilation openings. Install in

accordance with the manufacturer's instructions.

USE

AC power cord

Observe tim tbllowings To prevent the AC' power cord fl'om being

dmnaged. It the AC power cord is damaged, it may result in a fire or an

electric shock. Stop using it and ask _ our dealer or Sony service cemer m

exchange it.

[] Do nor place the TV where the power cord is subject m wear or abuse.

[] Do not pincll, bend. or twist the cord excessively. Tlle core lines may

be bared and cuk causing a short-circuit, and resulting in a fire or an

electric shock.

[] Do riot convert or damage tile po'_ er cord.

[] Do not allow mlythin_ ro rest on or roll over the

power cord.

[] Do not move tim TV with the power cord

plugged in.

[] Keep the power cord away 5tom heat sources

[] When you disconnect the AC power cord.

disconnect it t?om the wull outlet first.

[] Be sure to grasp tim plug wtlen disconnecting the power cord. Do not

8) Do not install near any heat sources such ,,, ..... _ pull tllepower cord.

asr diat r heatre isters stoves r _: rq Do not usethe suppliedAC power cord on anyother equipmenL

• a " 0 s ' g ' ' ; ', 0 _1 I_-

, ,. , ,. ,._. _l _<-_ 12] Use only an original Sony AC power cord. not other brands.

otner apparatus oncmmng ampnners_ _'l_

that produce heat. Jlllllillllllllll Wail outlet

9_ Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two

blade_ with one wider than the other. A grounding

type plug has two blades and a third grounding

prong. The wide blade or the third prong are

provided for your safety. If the provided plug does

not fit into your outlet, consult an electrician for

replacement of the obsolete outlet,

10) Protect the power cord from being walked on or

pinched particularly at plugs, convenience

The TV set wifll a three-wire grounding type AC

power cord plug must be connected to all AC power

socket outlet witl_ a protective earthing connection.

Do not use a poor fitting outlet. _---_ /)

Insert the plug fully into the outlet. If it is loose it may

cause arcing and result in a fire.

Conrac[ your electriciml to have the outlet changed

Wiring

When czmnecting cables, be sure to Lmplug the AC power cord thx your

s_,t_ty.

receptacles, and the point where they exit from the Tnke care not to catch your teet on the cables. It may damage the TV set.

apparatus. Electric shock ,¢_J%

l l} Only use attachments/accessories specified by the Do not touch the AC p ......... d or tl,e TV with a _{ _01 )

manufacturer, wet hand. If you plug/unplug the AC power cord _ 7/"_ _,,/

12_Use only with the cart stand trinod _ fi'omtheTVwill.... thand.itmay...... lectric _'-_l_

bracket, or table specified by tile _ shock. _l! _N_)/j

manufacturer, or soM with the _ ((_

apparatus. When a cart is used. use _" Lightning storms

caution when moving tile cart/apparatus

combination to avoid injury from tip-over.

l 3 } Unplug this apparatus during lightning storms or

when unused for long periods of time.

14 _Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in auy way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does nol operate

normally, or has been dropped.

For added protection for the TV during a

lighming storm, or when it is left unattended

and Lmused for long periods of time. unplug

it t_om the wall outlet and disconnect tile

antenna. This will prevent damage to the TV

due It lighming and power line surges.

When not in use

If you will not be using the TV set fl0r several da 3 ,. the TV set should be

disconnected Dora the AC power outlet for enviromnental mad sat)ty

reasons. The TV set is not disconnected fi'om tlle AC power source when

the TV set is switched off. To disconnect the TV set completely, pull the

plug t?om the AC power outlet.

Overloading :;:j

Tlds TV set is designed to operate on a _':

120- 240 V AC supply only. Take care not to _ _p-_

connect too mmly applimlces to the same AC ¢'[._

power outlet as thi_ could result in a tire or all

electric shock

Optional equipment

Do not install optional equipnlent too close to tile TV set. Picture

dist )rlion and!or noisy sound may occur if the TV set is positioned in

close proximity to any equipment enlitting electromagnetic radiation.

Small accessories

Keep small accessories out of children's leach.

ANTENNAS

Outdoor antenna grounding

ffan outdoor antenna h installed, follow the precautions below. An

outdoor antenna system should not be located in tile vicinity of overhead

power lines or other electric light or power circuits, or where it can come

m contact with such power lines or circuits.

WHEN INSTALLING AN OUTDOOR ANTENNA SYSTEM.

EXTREME CARE SHOULD BE TAKEN TO KEEP FROM

CONTACTING SUCH POWER LINES OR CIRCUITS AS CONTACT

WITH THEM IS ALMOST INVARIABLY FATAL.

Be sure tile antenna sybleln is grounded so as to provide some provection

against voltage surges and built-up srmic charges.

Section S10 of the National Electrical Code NEC" in tile U.S.A. and

Section 54 of the Canadian Electrical Code in Canada provides

intbrmation widl respect to proper grounding of the nmst and supporting

srrucmre, grounding of the lead-in wire to an antenna discharge unit. size

of grounding conductors, location of antenna discharge umt. connection

it grounding electrodes, and requirements Ibr the grounding electrode

Antenna grounding according to the National

Electrical Code, ANSI/NFPA 70

_,nteena lead-in wire

/- Ground clamcs

Antenna discharge unit

(NEC Section 810-20_

Grounding conductors

(NEC Section 810-21

MAGNETIC INFLUENCE

This TV contains a strong magnet in the speaker unit that generares a

magnetic field. Keep any items susceptible ro magnetic fields away Irom

tile speaker

SOUND

It a snapping or poppnlg sound i_om the TV is \ I_ / /_

continuous or flequent while me TV is operating, _ I\ _"

unplug the TV and ...... It your deal ........ ice 11I -----J Fg_)

technician. It is normal for some TV's to make _-_tL._a:::::::W_ _' ' '

occasional snapping or popping sounds, particu-

larly when being turned on or oft.

CARRYING TH E TV

Carry the TV in the specified manner

To avoid dropping tile TV and causing serious inJur3 be sure to Ibllow

these guidelines:

[] Before carrying file TV disconnect £] cables.

[] Carrying the large size TV requires at least two or fllree people.

[] When you carry dm TV, place your hand as illustrated and hold it

securely. Do not put stress on the LCD panel and tile t?ame around

tile screen.

[] When carrying tile TV. do not subject it to shocks or vibration, or

excessive torte

KDL-4OXBR4

KDL-46XBR4/

KDL-4OXBR5/ KDL-52XBR4

KDL-46XBR5 KDL-52XBR5

grounding

electrode system

NEC: National Electrical Code (NEC Art 250 Part H,

BATTERIES

[] Do not dispose o f batteries in a tire.

[] Do not ,holl circuiL disassemble or overheat the batteries.

[] Danger oi explosion if battery is incorrectly replaced. Replace onl_

widl tile same or equivalent Type.

Disposal of used batteries

Fo preserve our envlrOlllnent _dispose of used batteries 0ccording to your /'_

local laws or regulatiol s. ._],z/.,,

CLEANING rflllll

Cleaning the AC power plug _.___ ,_,,I II

Unplug the AC power plug and clean it regularly. L_.'_ _.

Ifthe plug is covered with dust mid it picks up 1IF'_%_I I___."l_-_ /

moisture, its insuk, ti...... y deteriorate and result _._ j \_'x3 "/

hi u fire. "F_ L_>,

Cleaning the screen surface/

cabi net of the TV set ,-_I[[---- '_

Unplug the AC power cord when cleaning this _Jl _ }'q

FV. IfnoL it may result in electric shock. Clean

fl]e cabinet of fl]e TV with a dry soft cloth. Tu

remove dust fl'om dm scieen, wipe it gently widl a sot} cloth. Stubborr

sirens may be removed with a cloth slightly dampened with a solution of

mild soap and warm water. Never use strong solvents such as thinner or

benzine for cleaning. If using a chendcally pretreatcd clodl, please follow

file instruction provided on the package. Tile ventilation holes can

[] When lifting or moving the TV. hold it firmly n'om the bottom. Place

your pMm direcdv under tile panel.

_ _" - _ X _

. _ ,/J . Xj..

accumulate dust over time. To ensure proper ventilation we reconmlend .... CoHtiHlged )

removing tile dust periodicall_ "once a month) using a wtcuum cleaner.

VENTILATION

The slots and openings in the TV are provided tbr necessary ventilation.

To ensure reliable operation oPthe TV and re promct it from overheating,

these slots and openings must never be blocked or coverer

Unless proper ventilation is provided, the TV may s .' ._ ,_

gather dust and get dirty• For proper ventilation f'_'-:_-_

observe the tbllowing:

[] Do nor install the TV thce up, down or sideways.

[] Do not il,qall the TV turned over or upside

dOWll

Objects and ventilation holes _,._

Never push objects alley kind into the TV through the

cabinet slots as they lnay touch dzmgerous voltage

points or short out parts that could result ill Ofire or m?

electric shock. Do not place any objects on tile TV.

MOISTURE

Moisture and flammable objects

[] the TV must not be exposed to dripping or splashing. Do not place

[] Never cover file slots and openings with a clod1 -_ . objects Blled with liquids, such as vases, on file TV,

or other materMs. [] Do not use power-line operated TV sets nell -._ _;-."Z!- -

water -- for example, near a bathtub, _ rf_"

I_ A I washbowl, kitchen sink, or laundry tub, in a I] _o II

wet basemenL or near a swimming pool, etc. __

It may result in a fire or an electric shock, c,,_ _\_

[] Never block thc slots and opeuings by [] DonotletthisTV getwet. Never spill liquid _ r_n

placing the TV on a be& .era, rug or other of any kind on tile TV If rely liqukl or solid /_/_

simil .......... object does tall through, do not operate tile __c_-_

TV. It may result ill electric shock or damage /,_/_ d'_'_._

to tile TV. Ha_ e it checked immediately by "_

qualified personnel.

[] To prevent fire, keep flanlmable objects or open ___

Leave some space around the I V set as shown below,

Otherwise air-circulation may be inadequate and cause

overneanng, wnich may cause a tire or oamage to the TV SOL

Installed on the wa I 117/8 inche_

30cml

4 inches

io_-

I 4 mcneg

jM0 .'rrll

0-,,,oLeave at least thisspace

_4 inches (lucre) around the sel.

Installed with stand 11 7/£incnes

30 cm

4 inches

lucm

2a/ainches

riches .... 16cm/

) cm

Leave at least th s SDaCOarouno IRe SOL

Wall ........ t installation requires tl...... f a _._7_1 _" _

Wall-Momlt Bracket. When installing at

retnovmg file TV, using the Wall-Mount _ _ll /_ )]]N

Bracket. be sure to use qualified contractors.

Ifnol properly secured during installation or

retnovM Promthe Wall-Mount Bracket. the

TV may fall and cause serious in:ur3

Optional wall mount

Observe tile tPllowing when irlstalling tile TV using a Wall-Moan r

Bracket.

[] Be sure to tallow the operating instructions supplied with tile

Wall-Mount Bracket when installing tile TV.

[] Be sure to attach the brackets supplied widl the Wall-Momlt Bracket.

[] Do not txmg the TV fl'om the ceiling. It may fall and cause serious

mjury

Placement

The TV should be installed nero" an easily accessible AC power outlet.

Observe tile following in placing tile TV. Otherwise

the TV may tbll fl'onl the stand or wall momlt, causing ,r_/-'f_ \

damage or serious injury. _/I / \

[] Place the TV on a stable, level surface• _/_:2_

[] Do not hang anytbing on tlle TV. DonotMlow ,v-_v_..._,_p

children to climb on the TV.

Never install the TV set as follows J ]]II

Air circulation is blocked. Air ctrcutation is blocked. _-_,_I_

Do not install the TV in places subjecT to exTrenle Temperature. such as in

direct sunlight, near a radiator or heating vent. ]f the TV is exposed to

extrelne tenlperature, the rv may overheat alia cause deformation ( t the

enclosure or cause tile TV to malthnction. Do not install the TVin a place

exposed to direct air conditioning. If the TV is installed in such a locahon.

nloise/l'e lnay condense inside mid may Cause a lnaltPlrlction

[] Never place tile TV in hot. oily, hmnid or r(_

......ively dusty pl..... ___2q__;

[] Do not install the TV where insects lllay P b_

enter

[] Do not install the TV where it may be

exposed to mecbmfical vibration•

V_ Do not install fl_e TV in a location where it may protrude, such as on

or behind a pinar, or where you might bump your head on it.

Otherwise, it may result in injury.

Preventing the TV from toppling over

rak_ measures t( prevent tile TV fi'om t( ppling over and causing inju U.

go prevent the TV tram toppling over. secure the TV to a wall or stand,

Placement for viewing

It is recommended to watch tile TV at a di-tance of 3 - 7 times that of the

screen height and in nloderatc brightness. Watching file TV tar too lung

or in a dark room may cause eye fatigue. To obtain a clear picture, do not

expose the screen to direct inmnination or direct sunlight. If possible, use

spot lighting directed down fl'om the ceiling,

Outdoor use

Do not install this TV outdoors, If the TV is exposed to

rain it ma) result in a fire or an electric shock. Do not

expose tile TV to direct sunlight, it may heat Lip and

become damaged.

Vehicle, ships and other vessels

Do not install this TV ltl a vehicle.

Bmnping of the vehicle may cause the TV to fidl down

and cause injury.

Do nm install this TV in a ship or vessel. If the TV is

Broken pieces

Do not throw anything at tile TV.

Tile screen glass may break by file impact mid

cause serious injury.

If tile surthce of tile TV cracks do not touch it until

yotl have unplugged the AC power cord.

Otherwise electric shock may result.

Handling of broken glass and liquid crystal

leakage

Ifthe LCD panel gets damaged, crystalline liquid leakage may occur, or

scattered broken glass may result. Do not touch broken glass or

crystalline liquid which is toxic, with bare hands as cuts, poisoning or

skin irritation may occur. Also. do not lel glass fi'ogments or leaked

crystalline liquid get into your eyes or mouth. Should either contacl your

eyes or nlouth, rinse the contacted area thoroughly will1 wafer and consult

your doctor.

SERVICING

Do not attempt to service the TV yotlrself since openltlg

tile cabinet may expose you to dangerous vol_/ge or other ...... @

uahhed serwce

Replacement parts

exposed to seawutur, it nl3y cause a fire or damage the (_--.._-

TV, _-_Y -_. "._ When replacement parts are required, be sure tile

.......... <%j_ ..... ice tuchnici ...... tifies in writing tllat he/she has _r_'_

Ivleolcal Insutuuons "<_): used repla ........ t parts specified by tl........... fact ..... _.__

Do ,lot place this TV ill a pl .... here medical _ that have tl .......... haracterisd .... tile original parts. _[

equipment is in use, _ ,,_,. __====_,_ / Unauthorized substitutions may result in a fire an /_'/

e=======m • ' _

It may cause a malffmction of medical equipment. I__) electric shock or other hazards.

-_,__.mil___ Safety check

Upon completion of any service or repairs to tile TV, (_ _._

ask the service teclmician tu perib ........ ti..... fcty _7_ [l _1

VOLUME ADJUSTMENT checks (as specified by tl....... mfacturer) to determine !i !_/-_,&2_ LII

that the TV is in saf_ operating condition, and to so ?, _>'

[] Adjust the volmne so as not to trouble your neighbors. Sound carrms certify. Ask a quMified service technician to dispose of the TV.

very easily at night. Therefore. closing the windows or using

headphones is suggestud.

[] When using headphones, adjust tim volume s. as ro avoid excessive

levels, as hearing damage may result.

LCD SCREEN

[] Although the LCD scJ_en is made with high-precision technology

and has effective pixels of 99.99% or more. black dots or bright

points of light 0_:d, blue, or green) may appear constantl 3 on the LCD

screen. This is a s_rucmral property of the LCD panel and is not a

malfunction.

V_ The LCD screen is made with high-precision technology and to

achieve a high level of per formance and picture quality, this TV's

backlight setting is set to maximize the brighmess of the TV.

However. uneven brightness may be observed when the LCD TV is

viewed in a dark alllbient without an input source or a bhlllK screen.

This condition is normM and not a malfhnction of the TV. Changing

the Pictur_ mode. Backlight setting, enabling the Light Sensor. or

turning on the Power management will improve this condition.

F- Do not expose tile LCD screen mrfhce to dil_ct sunlight. Doing so

may damage the LCD panel.

F- Do not push or scratch the LCD screen, or place objects on tof of the

TV. The image maI be uneven or the LCD panel may be damaged.

F- lfthe TV is used in a cold place, a smear may occur in the plcrure or

the picture may become dark. This does not indicate _failure. These

phenomena improve as lne lelnperamre rises

[] Ghosting nlay occur when still pictal_s are displayed continuously. It

should disappear after a f?w moments.

[] The screen and cabinet get warm when tile TV is in use. This is not a ....

malfunction.

[] Avoid spraying insect repellent with _ olatile material on the screen.

[] Avoid prolonged contact with rubber or plastic material.

For Customers in the United States

Lamp in this product contains mercu U. Disposal of

these materials may"be regulated due to

environmental considerations. For disposal or

recycling infolxaation, please contact your local

authorities or the Electronic Indu stries Alliance

(http://www.eiae.org).

Thank you for purchasing this Sony BRAVIATM high-definition television. The quality of the image

you see on your BRAVIA TV is only as good as the quality of the signal it receives. To experience

the full detail of your new BRAVIA TV,you need access to HD programming. Your BRAVIA TV can

receive and display HD programming from:

• Over-the-air broadcasting via HD-quality antenna

• HD cable subscription

• HD satellite subscription

• Blu-ray Disc TM Player or other external equipment

Contact your cable or satellite provider for information on upgrading to HD programming.

To learn more about HDTV, visit: http://www.sony.com/HDTV

The Four Steps to Full HD Experience: Set, Sound, Source, and Setup

Along with your BRAVIA TV set, a complete HD system requires an HD sound system, a

source of HD programming and proper setup connections. This manual explains basic setup

connections (see page 14). The Quick Setup Guide, enclosed separately, illustrates how to

connect other optional equipment.

Picture Quality and Aspect Ratio

You can enjoy crisp, clear images, smooth movement and high-impact visuals from 1080 HD

signals. When you compare a high-definition signal to a standard analog signal, you will notice

a big difference. The 1080 HD signals provide more than twice the vertical resolution of the

standard TV signal.

High-definition and standard-definition signals are transmitted with different aspect ratios (the

width-to-height ratio of the image). HDTV uses a wider screen than conventional standard-

definition TV.

16:9 (high-definition) source

Most HDTV signals use a wide screen aspect ratio

of 16:9. The 16:9 fills your BRAVIA screen and

maintains a crisp, clear, vivid picture.

4:3 (standard-definition) source

Most standard-definition signals use a boxy 4:3

aspect ratio. When a 4:3 image is displayed on an

HDTV, you will see black bars on the sides. The

picture quality may not be as sharp as with HD

sources.

• You can use the Wide Mode function of the TV to adjust the 4:3 image to fit the entire screen (see pages 23, 37

and 38).

TV Home Menu: XMBTM (Xross Media Bar)

The XMBTMis a menu of BRAVIA features and input sources displayed on the TV screen. The

XMBTMis an easy way to select programming and adjust settings on your BRAVIA TV. Press the

HOME button on your remote control to access the XMBTM.

Media

Category

Bar

Category Object Bar

From the horizontal Media Category Bar you can control:

• Settings: timer, picture, sound, screen and other options (see page 34 for customization

options).

• TV Channels: available channels are displayed on the vertical Category Object Bar.

• External Inputs: cable, satellite, VCR, DVD players or other inputs can also be selected

from the Category Object Bar for the External Inputs.

• This manual is %r the 40, 46 and 52 inch BRAVIA KDL-X Series models with screen size measured diagonally.

1. Installing the TV

stand

Table-Top

Stand

1 Screw tile support belt (supplied) to tile TV

stand with a wood screw (supplied).

2 Attach the support belt to the Table-Top Stand

with the securing screw (supplied) using a

coin, etc.

3 Adjust the length by pulling the support belt

toward you while holding the Table-Top

Stand.

• Be sure to take measures to prevent the TV from

toppling over and causing injury.

• The supplied wood scre'a, may not be used depending

on the type of TV stand. In this case, or when the

securing strength is not enough, use commercial

screws 1/8 to 3/16 inch (3 to 4 nnn) diameter to fit to the

TV stand. Consult your dealer about the types of

screw(s).

To Replace the Bezel Unit

The bezel unit can be replaced with others that are

sold separately. However. do not remove the unit

except to replace it. For details, see the instructions

supplied with bezel units.

This TV can be installed on a wall by using a Wall-

Mount Bracket (sold separately). Before mounting

the TV on a wall, the Table-Top Stand must be

removed fiom the TV.

Follow the simple steps below to remove the

Table-Top Stand:

Disconnect all the cables from the TV.1

Start removing the screws behind the TV (See

illustration below).

Do not remove any other screws from the TV.

3 When screws are removed, lift the TV off the

stand. Make sure that you carry out this task

with at least two or three people. Do not

attempt to lilt the TV by yourseff

• Do not remove the Table-Top Stand for any reason

other than to wall-mount the TV.

• When using an electric screwdriver, set the torque

setting to approximately 2 N.m {20 Kgf.cm}.

• Be sure to store the removed screws and Table-Top

Stand in a safe place until you are ready to reattach the

Table-Top Stand. Keep the screws away from small

children.

• For bracket installation, refer to the supplied Installing

the Wall-Mount Bracket and the instruction guide

provided by the Wall-Mount Bracket model for your

TV. Sufficient expertise is required in installing this

TV. especially to determine the strength of the wall for

withstanding the TV's weight.

• For product protection and safety reasons, Sony

strongly recommends that you use the Wall-Mount

Bracket model designed for your TV and that the

wall-mounting of your TV is performed by a Sony

dealer or licensed contractor.

2. Locating Inputs and Outputs

[] Headphone jack Connects to your headphones. If your headphones do not match the jack, use a suitable

plug adapter (not supplied).

• While headphones are connected, the TV speakers are muted.

[] VIDEO IN 2 Connects to the composite video and audio output jacks on your camcorder or other

VIDEO/R-AUDIO- video equipment such as a VCR or video game equipment.

L (MONO)

• If you have mono equipment, connect its audio output jack to the TV's L (MONO)

andio input jack.

[] HDMI IN 2 HDMI (High-Definition Multimedia Interface) provides an uncompressed, all-digital

HDMI audio/video interti_ce between this TV and any HDMI-equipped audio/video equipment,

snch as a set-top box, DVD player, Blu-ray Disc Player, A/V receiver as well as PC.

HDMI supports enhanced, or high-definition video, plus digital audio.

• HDM] connection is necessary to view 480i, 480p, 720p, 1080i, 1080p and 1080/24p

formats. Note that this TV displays all video input signals in a resolution of 1,920 dots x

1,080 lines.

• Be sure to use only an HDMI cable that bears the HDMI logo.

• When HDMI control compatible equipment is connected, conmmnication with the

connected equipment is supported. Refer to page 44 to set up this conmmnication.

• When connecting a HDMI control compatible audio sL/stem with HDMI jack, be sure to

also connect to the OPTICAL OUT jack.

KDL-40XBR4/ KDL-40XBR5/

KDL-46XBR4/ KDL-46XBR5/

KDL-52XBR4 KDL-52XBR5

[]

[] PC IN

(RGB/AUDIO)

Connects to a personal computer's video output connector using a HDI 5-HDI 5 cable with

ferrite core (analog RGB, not supplied). Call also be connected to other analog RGB equipment.

See "PC Input Signal Reference Chart" on page 16 for the signals that call be displayed.

• For some Apple Macintosh computers, it may be necessary to use an adapter (not

supplied). If this is the case, connect the adapter to the computer before connecting the

HDI 5-HD 15 cable with ferrite core.

• If the picture is noisy, flickering or not clear, adjust Phase and Pitch of Screen

settings on page 38.

[] HDMI IN 1

HDMI/

R-AUDIO-L

[] HDMI IN 3

HDMI

HDMI (High-Definition Mnltimedia Interface) provides an uncompressed, all-digital

audio/video interface between this TV and any HDMI-equipped audio/video equipment,

such as a set-top box, DVD player, Blu-ray Disc Player, A/V receiver as well as PC.

HDMI supports enhanced, or high-definition video, plus digital audio.

If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the

HDMI IN 1(with DVI-to-HDMI cable or adapter) jack, and connect the audio jack to the

AUDIO IN (L/R) jacks of HDMI IN 1.

DVI-to-HDMI cable

[] REMOTE

(KDL-40!46!52XBR5only)

[] VIDEO IN 1

S VIDEO

[] VIDEO IN 113

VIDEO/L(MONO)-

AUDIO-R

[] COMPONENT IN

112 (1080p/1080i/

720p1480p1480i)l

L-AUDIO-R

@_ Audio cable

DVl-to-HDMI adapter

• HDMI connection is necessary to view 480i, 480p, 720p, 1080i, ]080p and 1080/24p

formats. Note that this TV displays all video input signals in a resolution of 1,920 dots x

1,080 lines.

• Be sure to use only an HDMI cable that bears the HDMI logo.

• When HDMI control compatible equipment is connected, conmmnication with the

connected equipment is supported. Refer to page 44 to set up this connnunication.

• When connecting a HDMI control compatible audio system with HDMI jack, be sure to

also connect to the OPTICAL OUT jack.

This jack is for receiving the external control signal.

Connects to the S VIDEO output jack of your VCR or other video equipment that has

S VIDEO. S VIDEO provides better picture quality than composite video ([]) connection.

If both composite video and S VIDEO are connected, S VIDEO signal has priority.

Connects to the composite video and audio output jacks on your A/V equipment such as

a VCR or other video equipment. A third composite video and audio (VIDEO IN 2) is

located on the left side of the TV.

Connects to your equipment's component video (YPBPI0 and audio (L/R)jacks.

Component video2:_ovides better picture quality than the S VIDEO ([]) or the

composite video (l_J) connection.

• Component video (YPBPI<) connection is necessary to view 480i, 480p, 720p, 1080i and

1080p formats. Note that this TV displays all video input signals in a resolution of

1,920 dots x 1,080 lines.

[] DMeX/SERVICE This USB port is for service only unless you are connecting the optional BRAVIA

external module (DMeX).

[] DIGITAL OUT Connects to the optical audio input of your digital audio equipment that is PCM/Dolby

(OPTICAL) Digital compatible. Dolby Digital Audio signal from the HDMI input will be output as

PCM.

[] AUDIO OUT Connects to the left and right audio input jacks of your analog audio equipment. You can

(VAR/FIX) use these outpnts to listen to your TV's audio through your stereo system.

[] AC IN Connects the supplied AC power cord.

[] VNF/UNF/CABLE RF input that connects to your Cable or VHF/UHF antenna.

3. Connecting the TV

You can enjoy high-definition and standard-

definition digital programming (if available in

your area) along with standard-definition analog

programming.

• This TV is capable of receiving unscrambled digital

programming for both cable (QAM and 8VSB) and

external VHF/UHF antenna (ATSC).

• It is strongly recommended that you connect the

antenna/cable input using the 75-ohm coaxial cable

(not supplied) to receive optimum picture quality. A

300-ohm twin lead cable can be easily affected by

radio frequency interference, resulting in signal

degradation.

Cable or VHF/UHF (or VHF only)

75-ohm coaxial

cable _ _ Rear of TV

VHF/UHF/CABLE input

Use an optional A-B RF switch (not supplied) to

switch between the cable and over-the-air antenna

programming, as indicated below.

A-B RF switch

Cable _ _-_ Rear of TV

Antenna _ _LL_ VHF/UHF/CABLE input

• Be sure to set the Cable setting to On or Off in the

Channel settings t\_r the type of input signal you

choose (see page 40).

You can also enjoy high-definition programming

by subscribing to a high-definition cable service or

a high-definition satellite service. For the best

possible picture, make sure you connect this

equipment to your TV via the HDMI or

component video (with audio) input on the back of

your TV.

Shown with HDMI Connection

Rear of TV

i ' ?_iii!ii_i_i_ I_

HDMI cable

. CATV/Satellite

HD cable box/ |antenna

cable

HD satellite box

Shown with DVI Connection

Rear of TV

o-HDMI HD cable box/

_F_ I cable HD satellite box

U_OUT

AUDIO-L

(white) _

AUDIO-R --

(red)

CATV/Satellite

antenna cable

Audio cable

• If the equipment has a DVI jack and not an HDMI jack, connect the DVI jack to the HDM] IN 1 (with DVI-to-HDMI

cable or adapter) jack and connect the audio jack to the AUDIO IN (L/R) jacks of HDMI IN 1. For details, see

page 13.

Shown with Component Connection

Rear of TV

CATV/Satellite antenna cable

HD cable box/HD satellite box

AUDIO-R (red)_, /_

AUDIO-L (white)

PR (red) --o_ff

PB (blue) --°°°_t

Y (green)

Component video cable

Audio cable

Use tile TV as a monitor for your PC,

Shown below with tile HDI5 to HDI 5 connection, This TV can also be connected to a PC with DVI or

HDMI output, (Refer to the separate Quick Setup Guide.)

Rearof TV

HD15-HD15

cable (analog

RGB)

l Audio cable

(stereo mini plugs) Connect to an HDMI

compatible PC with

an HDMI cable.

• Connect the PC IN jack to the PC using the HDI5-

HDI5 cable with ferrite core (analog RGB, not

supplied) and audio cable (page 121.

• If the PC is connected to the TV and no signal has been

input from the PC l\_r more than 30 seconds, the TV

enters the standby mode antomatically (page 45).

PC Input Signal Reference Chart

After connecting tile PC to tile TV. set tile output signal from tile PC;according to tile chart below.

VGA 640 x 480 31.5 611 VGA

640 x 480 375 75 VESA

720 × 400 31.5 70 VGA-T

SVGA 800 x 600 37.9 6(I VESA Guidelines

8{1{I x 600 46.9 75 VESA

XGA 1024 x 768 48.4 611 VESA Guidelines

1024 x 768 565 70 VESA

1024 x 768 60.0 75 VESA

WXGA 1280 x 768 47.4 ,5(I VESA

1280 x 768 47.8 6(I VESA

1280 x 768 60,3 75

1360 x 768 47.7 6(I VESA

SXGA 1280 x 1024 64.0 6(I VESA

1280 x 1024 811.0 75 VESA

HDTV 1920 x 11180 67.5 6(I

• This TV's PC input does not support Sync on Green or

Composite Sync.

• This TV's PC VGA input does not support interlaced

signals.

• For the best picture quality, it is recommended to use

the signals (boldfaced) in the above chart with a 60 Hz

vertical frequency from a personal computer. In plug

and play, signals with a 60 Hz vertical frequency will be

detected automatically. (PC reboot may be necessary.)

Personal

corr 9uter

VCR

Game system

Blu-ray

Disc Player/

PS3

Digital

DVD satellite

player receiver

Audio Personal

system computer

Rear of TV

Digital

cable box

I%!ii

Digital Analog

recorder audio

equipment

VHF/UHF/CABLE

Digital audio

equipment

(AN Receiver/Home Theater)

Head )hones

Camcorder/ Camcorder

PS3

• Refer to the Quick Setup Guide (supplied) when connecting other equipment to your TV.

This TV is equipped with BRAVIA Theatre Sync.

The HDMI Control function enables BRAVIA

Theatre Sync to allow communication between

Sony TV's and Sony equipment. Only Sony

equipment with HDMI Control capability is

supported.

To Connect HDMI Control Equipment

Use an HDMI cable that bears the HDMI logo for

connection. See page 17 or see the HDMI

connection shown in the Quick Setup Guide

provided with the TV documentation.

Setting the HDMI Control

In order for the HDMI Contlol function to operate,

the TV and other Sony HDMI Control equipment

must be setup. See page 44 on how to turn the

HDMI Control On. For other equipment, refer to

the operating instruction for that equipment.

HDMI Control Available with Your TV

Once the supported equipment is connected, the

following operations are available:

• Turn offthe equipment automatically when

you turn off the TV.

• When the connected equipment is turned on

by One-Touch-Play, the TV will automatically

turn on and select the respective HDMI input.

• Automatically turn on equipment listed under

the External Inputs on the XMB_x_when

selected, see pages 9 and 32.

When a Sony A/V receiver with BRAVIA Theatre

Sync is connected, the following additional

operations are possible:

• Turning on the A/V receiver when the TV is

turned on.

• Automatically switching to the audio output of

the A/V receiver's attached speakers.

• Adjusting the volume and muting of the A/V

receiver with the TV's remote control.

• The A/V receiver cannot be selected from the XMB_.

You can bundle the connecting cables as illustrated

below.

• Do not bnndle the AC power cord with other

connecting cables.

• The hook of the cable hokter can be opened from

either sides depending on attaching position.

4. Setting Up the Channel List

- Initial Setup

The Initial Setup screen appears when you turn

on the TV for tile first time.

After you finish connecting the TV. you can run

Initial Setup to create a list of available analog

and digital channels if you have connected an

antenna or cable directly to the TV's VHF/UHF/

CABLE input.

You will be prompted to select tile language of

your choice to be used for all the on-screen

settings.

Use the remote control to navigate through the

Initial Setup:

#/# button:

Allows you to highlight options

where applicable.

@ button:

Allows you to select the

highlighted option and advance

to the next screen.

. button:

Allows you to move back to the

previous screen.

. button:

Allows you to move to the next

screen.

Follow the help text provided on the screen to run

Auto Program with the connected signal source

or select Skip to skip the Auto Program if you

are receiving channels fiom a cable box or satellite

receiver and the VHF/UHF/CABLE input is not

connected. The Auto Program will scan for

available channels. When the Auto Program is

completed, the TV will display how many analog

and digital channels are found.

• If you accidentally tnrn off the TV during the Initial

Setup process, the Initial Setup will restart from the

beginning when the TV is turned back on.

• The Auto Program may be canceled while the

channels are being scanned. Press RETURN first then

press either I,/* on the remote control, highlight "Yes"

to cancel or "No" to resume Auto Program.

To Run Initial Setup Again or Auto

Program at a Later Time

Select the Initial Setup feature fi'om the XMB,_,

or refer to the Initial Setup described on page 45.

To run Auto Program, see page 40.

To Add Digital Channels

Use the Add Digital Channels feature as

described on page 40. (Useful for antenna

installations.)

To Display the Picture in Your Preferred

Aspect Ratio

Select the proper Wide Mode as described on

pages 37 and 38.

You may want to set up convenient features such

as Favorites (see page 21), Show/Hide

Channels (page 41), Edit Channel Labels

(page41) whenAuto Program is completed.

if)

Remote Control and TV Controls/Indicators

Insert two size AA batteries (supplied) by matching

O and 1} on the batteries to the diagram inside the

battery compartment of the remote control.

t:n°%

Buttons located at the right side of the TV will operate the same as these buttons

on the remote control.

• The 5 button, PLAY and CH + have a tactile dot. Use them as a reference

when operating the TV.

[] DISPLAY Press once to display the information pertaining to the

channel and/or program when available. The OSD (On Screen

Display) will time out in a few seconds or press again to

immediately turn off the display. You can also set the display

to show minimal information. See Info Banner on page 44.

[] LIGHT Press to illuminate the buttons on the remote control so that

you can control them easily even if the room is dark.

[] FUNCTION The FUNCTION button indicator lights up momentarily

Buttons when pressed to show which external equipment the remote

control is operating. You must first press one of these

FUNCTION buttons to operate the corresponding equipment.

See page 26 for programming the remote control.

[] 0-9 ENT Press 0-9 to select a channel; the channel changes alter two

seconds. Press ENT to change channels immediately.

Page is loading ...

Sony KDL-40XBR4 Owner's manual

Brand: Sony

Model: KDL-40XBR4

Category: LCD TVs

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Sony KDL-40XBR4 Owner's manual

This manual is also suitable for

Sony KDL-40XBR4 Owner's manual

Related papers

Other documents