Electrolux TWSL5M100 User manual

Brand: Electrolux

Model: TWSL5M100

Type: User manual

Electrolux TWSL5M100 is a versatile heat pump dryer suitable for both domestic and professional use. Equipped with a large capacity, it can handle substantial laundry loads efficiently. Thanks to its advanced heat pump technology, it operates economically while providing gentle drying results. The device offers a variety of drying programs tailored to different fabric types and care requirements, ensuring optimal treatment for your clothes.

Aufstellanleitung für Wärmepumpentrockner

für Mehrfamilienhaus und Gewerbe

Notice d’installation pour séchoirs

à thermopompe pour immeuble collectif

et usage professionnel

Istruzioni per l’installazione

di asciugatrici a termopompa per le case

plurifamiliari e l’industria

Installation instruction for

heat pump dryers in apartment buildings

and for professional uses

Instruktions-Nr.

No. d’instruction 637 197.AC

No. d’istruzione

Instruction No

WT11 MFH W

Page is loading ...

Transport



When transporting (unloading and moving) and install-

ing the machine ensure that it does not fall down or

turn over. There is danger of injury, and the device can

be damaged.

The machine is very heavy. Danger of injury when lifting

the appliance.

Do not lift the appliance by its protruding components!

Tilt the device to the right:

 Maximum 45° tilt permitted

Tilt the device to the left::

 The device may be laid carefully

on the left side area.

Tilt the device forward:

 Maximum 45° tilt permitted

After each transport, the device must be left idle for

10 minutes before it may be switched on.

Dispose of the packing material correctly and do not keep

it. Playing children might get hold of it and be exposed to

danger (e.g. risk of suffocation with the sheeting).

Installing the appliance



 To guarantee optimum performance, the dryer must be

installed in a room that is adequately ventilated. Do not

install the dryer in an enclosed area (such as a closet with

a solid door) or in any area without open windows, air

vents, air conditioning, doors with ventilation slots or any

other means of fresh air circulation (room volume >50m3).

When installing and connecting the appliance, the

fol lowing safety instructions, warnings, general

in structions and possible particular instructions of the

responsible water and electric power stations are to be

observed.

Operating temperature: 5 to 35°C.

In cases of doubt, have the installation carried out by a

specialist.

Do not plug in a machine with visible damage.

Lay hoses and cables in such a way that they do not

represent a risk of tripping.

The machine must not be mounted and operated out-

doors (e.g. balcony). Otherwise risk of short circuit and/

or risk of re.

The machine must not be placed behind a lockable door,

a sliding door or a door with a hinge which is opposite

the drum dryer.

Installation area

In order to ensure the stability of the appliance, the

installation area must be rm and level. Soft oor cover-

ings, e.g. tted carpets or coverings with a foamed

material backing are not suitable as an installation area.

Keep the area surrounding the dryer free of dust and uff.

Do not obstruct the ventilation grille at the bottom of

the front of the appliance, otherwise sufcient ow of

cooling air cannot be guaranteed.

During the drying process take care to ensure that the

room is well ventilated (open windows or the door,

unclosable ventilation openings in the walls or doors).



If the dryer cannot get enough fresh, cool air and instead

begins to circulate warm air, its performance might de-

crease

noticeably!

The minimum distance between the machine and the

wall or possibly another machine is 1cm.

X When installing the appliance, take note of the required

dimensions.

Fixing kit



For installation on slippery ground, e.g. installation base

with tile surface, two self-adhesive receptacles secure

the machine from shifting and protect the surface.

You can purchase the xing set as a kit at your specialist

retailer or through our customer services team:

Steel xing set – to be drilled: Order No. S110

Plastic xing set – to be glued: Order No. 51215

Leveling the appliance

In order to ensure the machine’s stability, it must be in a

vertical position with all four feet rmly on the oor and

it must not wobble. Otherwise the machine might move

during operation and cause any damage.

Aligning the appliance with the help of a spirit level on

all sides.

If necessary, correct the height of the appliance feet.

Washer-Dryer tower

In order to save space (installation space), you can place

your dryer on top of a washing machine (washer-dryer

tower).

For this sort of installation, the dryer must be fastened

to the washing machine with a staking kit. You can ob-

tain the appropriate parts as a construction kit from your

specialist dealer or our After-Sales Service:

Mounting on washing machine for apartment buildings:

Washer-dryer tower staking kit, white:

Order No. 51010

Washer-dryer tower staking kit, anthracite:

Order No. 51019

The dryer may not be installed on top of a domestic

washing machine.

Connect condensate pipe



The dryer comes with a condensate drain hose pre-in-

stalled in the back. The hose can be installed to a drain

pipe either left or right of the dryer.

The dryer produces condensed water that will be col lec-

ted in an internal container. Periodically, a pump will

empty that container by pumping the condensed water

through the condensate drain hose into a drain pipe.

Attention!

Make sure that the condensate drain hose is carefully

installed without traction of any kind. If the hose is

in stalled too tightly and is being pulled, it may develop

kinks or sharp bends, and the pump will no longer be

able to pump the water successfully through the hose

into the drain.

The waste water hose may be conducted in the siphon

of a sink unit or another waste pipe. In doing so, atten-

tion should be paid to the pump which does not need

to pump higher than 39.37inches (100cm). Besides, the

sewage may not ow back into the condensate pan.

z Dimensions condensate drain hose: ø 10/15x1900mm

z If the distance to the drain at the customer's is too

big, you can obtain an extension set from your specialist

dealer or customer servic:

Drain hose extension 2m: Order No. 51023

Installation of the hose elbow

The hose is inserted into the supplied hose elbow and

xed on the ends of both sides with a cable connector.

Possibilities for connection:

Introduction of the condensate pipe into a

standpipe with siphon

Installation of the dryer next to the washing

machine

For the connection to a common siphon a non-return

valve is to be installed at the backside of the dryer!



This valve is available under the order number E 631 944.

Installation of the dryer on the washing

machine

For a washing and drying tower that share a concealed

siphon it is necessary to camber the condensate pipe!

Run hose over the supplied hose elbow.

Further possibilities for connection

1. Direct connection on the siphon of a sink unit. If neces-

sary, attach non-return valve (Order

number

E 631 944).

2. Inserted hose elbow in a sink.

3. Introduced hose in a oor drain.

Electrical connection

The connection of the machine to the power supply must

be carried out by a specialist.

Prepare the electrical connection (in the building) exibly

in accordance with the connection diagram and the

regulations of the regional power supply company. In

rooms in which fault-current protective switches are

required or recommended in order to increase safety,

the release current must be 30mA.

The appliance is licenced for xed connection, all-pole

disconnectable by a main switch with contact distance

of min. 3mm.

Under no circumstances use any multiple plugs/couplings

and extension cables. Risk of electric shock and risk of re.

z The device will be delivered with a 4-wire mains lead

(length: 150cm) to connect to a 2 phase alternating cur-

rent with non conductor.

z Fuses and switches are not included in the scope of

supply.

z The appliance is supplied with a cable without a plug.

z If a larger distance is required to the mains connec-

tion, you can obtain the following extension set from

your specialist dealer or customer servic:

Connection cable 3m: Order No. 51022

400V 2N ~

ENL1

L1NPE L2

Heat pump 0,7 kW

Additional heating 2,0 kW

Other 0,7 kW

Fuse 10 A

Connection variant for 1-phase alternating current

Mains connection set 1L / N / E/ 16A

Order No. 637 226

z 150 cm long, 3-core power line for connection to

1-phase alternating current with neutral conductor.

z Fuses and switches are not included in the scope of

supply.

z The appliance is supplied with a cable without a plug.

230V 1N ~ (16A)

ENL1

LNPE

Heat pump 0,7 kW

Additional heating 2,0 kW

Other 0,7 kW

Fuse 16 A

L1 = brown

L2 = black

N = light blue

PE = yellow/green

Page is loading ...

01.12 d/f/i/e Printed in Switzerland Subject to change without notice

Electrolux TWSL5M100 User manual

Brand: Electrolux

Model: TWSL5M100

Type: User manual

Download PDF

report

in other languages

italiano: Electrolux TWSL5M100 Manuale utente
français: Electrolux TWSL5M100 Manuel utilisateur
Deutsch: Electrolux TWSL5M100 Benutzerhandbuch

Electrolux TWSL5M100 User manual

Electrolux TWSL5M100 User manual

in other languages

Related papers

Other documents