Thermador CET304FS/01 Installation guide

INSTALLATION

INSTRUCTIONS

For Electric Cooktops

Installation Instructions

Instructions d'installation

Instrucciones de Instalacion

311

12-20

21 29

dDlr ° AnAmevlcanlcon,,°

Model:

CES366FS

CES365FS

CES304FS

CET366FS

CET304FS

CEM365FS

CEM304FS

Page is loading ...

Important Safety Instructions

READ AND SAVE THESE INSTRUCTIONS

Important

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.

LEAVE THESE INSTRUCTIONS WITH THE APPLIANCE AFTER INSTALLATION IS

COMPLETE.

WARNING: If the information inthis manual is not followed exactly, fire or

shock my result causing property damage or personal injury.

WARNING: Do not repair or replace any part ofthe appliance unless

specifically recommended in this manual. Never modify or alter the

construction of the appliance.

Improper installation, service or maintenance can cause injury or property

damage. Refer to this manual for guidance. Refer all servicing to a factory

authorized service center.

Remove alltape and packaging before using the appliance. Destroy the packaging

after unpacking the appliance. Never allow children to play with packaging material.

Appliance handling safety Hidden surface may have sharp edges. Use caution when reaching behind or under

appliance.

Electric safety Before installing, switch off the circuit breaker in the fuse box. Lock circuit breaker to

prevent power from being turned on accidently.

The circuit breaker must have a contact separation of at least 1/8"(3mm) in all poles.

Be sure your appliance is properly installed and grounded by a qualified technician.

Installer show the owner the location of the circuit breaker or fuse. Mark itfor easy

reference.

This appliance has been tested in accordance with ANSI/UL 858 Standard for Safety

for Household Electric Ranges and CAN/CSA E60335 1 and E60355 2 6 National

Standard of Canada for Household Cooking Ranges. It isthe responsibility of the

owner and installer to determine if additional requirements and standards apply in

specific installations.

Related equipment safety

The cooker isonly guaranteed safe to use if installed by a specialist in accordance

with these installation instructions. The installer is liable for any damage resulting

from incorrect installation.

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet

storage space located above the surface units should be avoided. Ifcabinet storage

isto be provided, the risk can be reduced by installing a range hood that projects

horizontally a minimum of 5" (127mm) beyond the bottom of the cabinet.

Do not install refrigerators, dishwashers, non-fan-assisted ovens or washing

machines which fit underneath the cooktop.

Note: We strongly recommend the installation of a ventilation system with this

appliance.

3

Before you begin

Tools and parts needed

_, Phillips head screwdriver

_, Pencil

_, Drillwith 1A"bit

_, Jigsaw

_, Tape measure

Note: Additional materials may be necessary for installation insolid surface

countertops. Contact the countertop manufacturer.

Parts included

4

Preparation

Countertop requirements

Note

_IL WARNING: To reduce the risk of ignition of surrounding combustiblematerials, install at least 2" (51mm) from both sidewalls and the rear wall.

The countertop must be level and horizontal. The stability of the countertop must still

be guaranteed after the cutout has been made.

After preparing cutout, remove shavings as they can affect the function of electrical

components.

Seal the cutout surfaces to make them heat-resistant. This prevents the surfaces

from swelling as a result of moisture.

Solid surface countertops often require special installations. For example, heat

reflective tape and rounded corners may be necessary. Contact the countertop

manufacturer for instructions specific to your countertop.

30"

Model:

CES304FS

CET304FS

CEM304FS

min. 2" (51mm)

min. 2 I/4" (57mm)

19 7/8 - 20"

(505 o508mm

3/4 - 28 7/8"

(731 - 734mm)

I

5

36"

Model:

CES366FS

CES365FS

CET366FS

CEM365FS

min. 2" (51mm)

Qt/4" (6 ram)

min. 2 1/4" (57mm)

19 7/8 - 20"

3/4 - 34 7/8"

(505 - 508mm

(883 - 886mm)

Cabinet requirements The distance from the top of the cooktop to the bottom of cabinets above can be

reduced to 24" (610mm) when the bottom of the wood or metal cabinet is protected

by not less than 1/4" (6.35mm)-thick flame-retardant millboard covered with not less

than no. 28 MSG sheet steel, 1/64" (0.4 mm) thick stainless steel, 1/36" (0.6 mm)

aluminum or 1/36" (0.6 mm)thick copper.

6

installation procedure

_IL WARNING: Use protective gloves while installing the cooktop.

Sealing tape

Turn cooktop upside down and fix the sealing tape on the edge of the cooktop.

7

Secure cooktop to

countertop

The cooktop should be secured to the countertop using the clamps provided.

Prior to inserting cooktop into cutout, attach clamps to the corresponding slots.

2,

J

Place cooktop into cutout.

8

Insert clamping screws into the bracket and secure cooktop to countertop. Use a

wood block to protect fragile countertop materials.

A minumum clearance of 1/8"(3mm) is required between the unit and any oven

installed beneath it.

min. 1/8" (3mm)

--)

9

Electrical installation

Electrical requirements

3.8" (96mm) + Fitting/Conduit 0.9" (23mm)

12" (300mm) Approximate

t

"J" box

Conduit approx.

3 feet (-900mm)

Power Supply

Electrical connection

You can find the identification plate with the electrical specifications on the underside

of the appliance. The junctionbox must be located within 3 feet of the cooktop

connection. It should be easily accessible for service purposes.

Model 240 V AC, 60 Hz system: 208 V AC, 60 Hz system:

circuit breaker circuit breaker

CEM304FS 40 Amp 30 Amp

CET304FS 40 Amp 30 Amp

CES304FS 40 Amp 30 Amp

CEM365FS 40 Amp 40 Amp

CET366FS 50 Amp 40 Amp

CES366FS 50 Amp 40 Amp

CES365FS 50 Amp 40 Amp

_bk AUTION: Before installing, switch off the circuit breaker in the fuse box.Lock circuit breaker to prevent power from being turned on accidently.

The branch-circuit breakers ampacity, the wire sizes and the connections must be

conform to the requirements of the National Electrical Code or Canadian Electrical

Code and all local codes and ordinances.

Attach flexible conduit to the junction box.

_ ARNING: To reduce the risk of electric shock and fire, do not use aflexible power-supply cord.

10

Connect the cooktop lead wires to the junction box supply wires in proper phase:

black (L1) to black

red (L2) to red

blank copper wire to ground

Test the installation

_ AUTION: Before turning on power supply, make sure all controls are in

the OFF position.

Remove everything from the cooktop surface including stickers.

Clean cooktop surface with cooktop cleaning creme.

Switch on the circuit breaker.

Verify that elements function properly.

Service

Contact our Service department ifyour appliance needs repair. Our central Customer

Service Center (see below) will also be happy to supply you with details on a center

close to you.

When you contact our customer service, please have the E number and the FD

number for your appliance available.

You can find the identification plate with these numbers on the underside of the

appliance.

Questions? Please contact us. We look forward to hearing from you!

1-800-735-4328

www.thermad0r.c0m

5551McFaddenAve.

HuntingtonBeach,CA92649

11

Page is loading ...

9000 293 136 .T180689

_Of ° An Am evlcanIcon°

5551 McFadden Ave., Huntington Beach, CA 92649.1-800-735-4328 *www.thermador.com

(£c)BSH Home Appliances Corporation 2006

Thermador CET304FS/01 Installation guide

Thermador CET304FS/01 Installation guide

in other languages

Related papers

Other documents