2. Ecoair
  3. Artica

Ecoair Artica Owner's manual

  • Hello! I am an AI chatbot trained to assist you with the Ecoair Artica Owner's manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
ARTICA MK2
8000Btu
Window Kit
Installaon Guide
UK
C423 - 20191009 Local Air Condioner
© 2019 EcoAir 1 All rights reserved
English
rain shield
foam seal A foam seal B (adhesive type) bracket
INSTALLATION
PACKAGE CONTAINS
Note: check if the accessories are available before installaon.
TOOLS NEEDED FOR INSTALLATION
cross screwdriver straight screwdriver saw
measurement tape scissors pencil
joint A joint B
joint C discharge pipe
Exhaust Kit (Come out with the Unit)
window Panel insect guard net
rain guard (short) rain guard (long)
Window Kit
screws
washer x 4 spring washer x 4 nut x 4
© 2019 EcoAir 2 All rights reserved
English
INSTALLATION
1. Connect the Joint B & Joint C.
2. Clamp Joint B + Joint C into the inner side of the window panel.
3. Secure the insect guard on Joint B & Joint C with screws.
4. Secure the rain guard and rain shield on the window panel with nuts, spring washers, washers
and bolts.
5. Cut the Foam seal B (adhesive type) to the proper length and aach it to the window stool and
to the boom of sash.
6. Aach the window panel to the window stool. Make sure that the exhaust cover is aached to
the window panel. Inner width of the window:20.5"(520mm)Use the window panel.
Installaon in a double-hung sash window (Oponal)
Foam Seal B (adhesive type)
Window Panel
Inner Side
Joint B + Joint C
Joint C (lower)
Joint B (upper)
Clasp
Screws
Window Panel
Insect Guard
Nuts
Bolt
Washers
Spring Washers
Rain Guard
Window Panel
Screws
Washers
Rain Shield
Spring Washer
nuts
© 2019 EcoAir 3 All rights reserved
English
INSTALLATION
The window panel cannot be installed in windows less than 20.5" (520mm) wide,
as you will be unable to shut the exhaust cover.
1) Open the window sash and place the window panel on the window sill.
2) Secure the window panel to the window stool with screws.
Inner width of the window:20.5" (520mm)- 37.4" (950mm)
Use the window panel and the adjustment panel.
1) Open the window sash and place the window panel on the window sill.
2) Slide the adjustment panel to t the window frame width.
3) Secure the window panel to the sill with screws.
Inner width of the window:37.4" (950mm) - 56.7" (1440mm)
Use the window panel, the adjustment panel and the extension panel.
1) Open the window sash and place the window panel on the window sill.
2) Slide the adjustment and extension panels to t the window frame width.
3) Secure the window panel to the window sill with screws
Installaon in a double-hung sash window (cont.)
Exhaust Cover
Window Panel
Adjustment Panel
Extension Panel
Adjustment Panel
© 2019 EcoAir 4 All rights reserved
English
INSTALLATION
5. Close the window sash securely against the Window panel.
6. Stu the Foam seal A between the glass and the window to prevent air and insects from geng
into the room.
7. Aach the bracket with a screw. (Recommended)
Installaon in a double-hung sash window (cont.)
Please lay a tabular material underneath the window panel in case you could not aach
the rain guard or the window adapter properly due to the deep window sill.
© 2019 EcoAir 5 All rights reserved
English
INSTALLATION
1. Connect the Joint B & Joint C.
2. Clamp Joint B + Joint C into the inner side of the window panel.
3. Secure the insect guard on Joint B & Joint C with screws.
4. Secure the rain guard on the window panel with nuts, spring washers, washers and bolts.
5. Cut the Foam seal B (adhesive type) to the proper length and aach it to the window frame and
to the side of sash.
6. Install the window panel into the window frame.
Make sure that the exhaust cover is aached to the window panel. Inner height of the win-
dow:20.5"(520mm). Use the window panel
Installaon in a sliding sash window (Oponal)
Foam Seal B (adhesive type)
Joint C (lower)
Joint B (upper)
Clasp
Window Panel
Inner Side
Joint B + Joint C
Screws
Window Panel
Insect Guard
Screws
Window Panel
Washers
Spring Washers
Bolt
© 2019 EcoAir 6 All rights reserved
English
The window panel cannot be installed in windows less than 20.5" (520mm) high,
as you will be unable to shut the exhaust cover.
1. Open the window sash and place the window panel on the window frame.
2. Secure the window panel to the window frame with screws
Inner height of the window:20.5" (520mm)- 37.4" (950mm)
Use the window panel and the adjustment panel.
1. Open the window sash and place the window panel on the window frame
2. Slide the adjustment panel to t the window frame height.
3. Secure the window panel to the window frame with screws.
Inner height of the window:37.4" (950mm) - 56.7" (1440mm)
Use the window panel, the adjustment panel and the extension panel.
1. Open the window sash and place the window panel on the window frame.
2. Slide the adjustment and extension panels to t the window frame height.
3. Secure the window panel to the window frame with screws.
INSTALLATION
Installaon in a sliding sash window (Cont.)
Exhaust Cover
Window Panel
Adjustment Panel
Adjustment Panel
Extension Panel
© 2019 EcoAir 7 All rights reserved
English
4. Close the window sash securely against the Window panel.
5. Stu the Foam seal A between the glass and the window to prevent air and insects from geng
into the room.
6. Aach the bracket with a screw. (Recommended)
Please lay a tabular material underneath the window panel in case you could not aach the
rain guard or the window adapter properly due to the deep window sill.
Bracket
INSTALLATION
Installaon in a sliding sash window (Cont.)
/