Gazelle GAZELLE POWER PLUS Assembly Instructions

Brand: Gazelle

Model: GAZELLE POWER PLUS

Type: Assembly Instructions

Gazelle GAZELLE POWER PLUS is a fitness equipment that allows you to exercise your legs and arms. It has four levels of resistance, so you can adjust the intensity of your workout as you get stronger. The device also features a built-in computer that tracks your progress, so you can see how you're improving over time. With its sturdy construction and comfortable design, the Gazelle GAZELLE POWER PLUS is a great way to get a full-body workout at home. Some of its many benefits include:

Improved cardiovascular health
Increased muscle strength and endurance
Reduced body fat
Improved balance and coordination

Improved cardiovascular health
Increased muscle strength and endurance
Reduced body fat
Improved balance and coordination

HYDRAULICS INSTALLATION

(after complete unit is assembled)

electronics

water bottle

and holder

cross tube

right frame

left frame

axle tube

right

swing arm

left

swing arm

left

base

frame

handlebars

right

base

frame

left

swing arm

right

frame

left

frame

right

swing arm

poly bag

frame plate

M10 x 95mm

hex bolts

M10 x 95mm

hex bolts

left base frame

right base frame

cross tube

frame plate

To familiarize yourself

with the parts, lay them

out on the floor as

shown. Cables should

lay on top of the frames

(be careful you do not

tangle cables with

swing arms).

Tools Required for Assembly: Phillips Screwdriver

Wrenches (provided)

Occasionally our products contain components that are pre-lubricated at the factory. We recommend that you protect

flooring, or anything else the parts may contact, with newspaper or cloth.

b. Lying Out Swing Arms

Move the left and right swing arms to the

center of the frame assembly as shown. Make

sure the cables lay on the top of all pieces.

a. Base Frame Assembly

First, remove the 6, M8 x 25mm bolts and

spring washers on the left and right base

frames marked L and R with the arrows

toward the front.

Second, use 4 of the M8 x 25mm bolts,

2 on each end, to attach the cross tube to

the top of the base frame.

We recommend having someone

available to help you. Due to the

size and weight of some of the

pieces, assembly is easier and safer

if there are two people.

ASSEMBLY INSTRUCTIONS

fastener pack

M8 x 25mm hex bolt (2),

spring washer and washer

(attaches axle tube to frame)

M6 x 40mm Phillips bolt (4)

(attaches end caps to frame)

wrench (2)

M10 x 95mm hex bolt (4)

and spring washer

(attaches frame plate &

cross tube to base frame)

frame plates

large

washers

end caps

Third, attach the frame plates to each side

of the base frames using (4) M10 x 95mm

hex bolts and spring washers from the

fastener pack. These bolts also secure the

base frame to the cross tube. Tighten bolts.

front

remove 6

M8 x 25mm

bolts from

left base

replace 2

M8 x 25mm

bolts to attach

cross tube

replace 2

M8 x 25mm

bolts to attach

cross tube

remove 6

M8 x 25mm

bolts from

right base

1/20/05

mounting

bracket

foot tube

washer

nut

left

swing

arm

left side

shown

M8 x 70mm

hex bolts

hydraulics

fastener pack

closed end

wrenches

clips

springs

M8 x 70mm hex bolts,

washers and nylon nuts

mounting brackets

washers (4)

12mm

washers (2)

8mm

rubber pad (4)

nut caps

nuts

If you do not wish to use the hydraulics,

remove the clips and move the hydraulics into

the zero resistance slot. Replace both clips.

NOTE: There are 4 levels of resistance on the

unit. Begin exercising at Level 1 (zero resistance)

and slowly advance to the next level when the

current level becomes too easy. The levels

increase as you move the pin towards you to

the next position.

Zero

Resistance

Level 1

Level

RESISTANCE LEVELS

TO INSTALL YOUR HYDRAULICS

left

right

clip in zero resistance

PARTS

a. Fasten mounting brackets

to the outside edges of the

left and right foot tubes using

(2) hex bolts, (2) washers and

(2) nylon nuts. Tighten bolts

with wrenches provided.

d. Pull left hydraulic down to allow pin to pass

through resistance hole in mounting bracket. For

ease of assembly, raise foot platform slightly so

pin can reach mounting bracket.

e. Lock clip onto hydraulic pin.

Repeat Steps d and e on

right side.

b. Mount left hydraulic to left swing arm using

(1) spring, (1) M12 washer, (2) rubber pads,

(1) M12 washer (1) M8 washer, (1) nut, and

(1) nut cap.

Note: the bottom of

the hydraulic must

have the pin facing

the swing arm.

c. Mount right hydraulic

to right swing arm using

(1) spring,

(1) M12 washer,

(2) rubber pads,

(1) M12 washer,

(1) M8 washer,

(1) nut and

(1) nut cap.

Note: the bottom of

the hydraulic must

have the pin facing

the swing arm.

left

swing

arm

inside

of unit

outside

of unit

foot

platform

spring

nut

cap

washer

(M12)

washer

(M8)

rubber

pad

washer (M12)

clip

foot

platform tube

mounting bracket

Repeat on right side.

Attaching the

End Caps and

Water Bottle

Holder

Determine which

side of your unit

you want the water

bottle (shown on

the left side here).

Attach the end cap

onto the frame using a M6 x 40mm Phillips bolt in the lower

hole only. Align the water bottle holder on the end cap so the

tab on the back of the holder fits into the bottom hole of the

end cap. Secure the water bottle in place with an M6 x 40mm

Phillips bolt.

Attach the other end cap with (2) M6 x 40mm Phillips bolts.

tab

end

cap

M6 x 40mm

phillips bolts

view as if

stepping

on unit

Handlebar Assembly

Remove the bolts and washers from the handlebars.

Slide the handlebars into swing arms as shown.

On the front side of the unit, align the holes and insert

bolts with washers. Tighten with the wrench provided.

insert screw

axle tube

right

swing arm

left

swing arm

view as if you are using the unit

Electronics Assembly

Step 1:

Remove the two small screws from the bottom of the electronics with the screwdriver provided.

Insert the two “AAA” batteries in the top housing.

Step 2: Attach the bottom housing with the large bolt provided in the bag with the batteries as shown.

Step 3: From the front of the unit, place the top housing onto the bottom housing and replace the two small screws

you removed in Step 1 as shown.

reinsert the two small screws

Remove the two small screws

front

view

left frame

left base

frame

c. Left Frame/Swing Arm Assembly

Raise the left frame (marked with the L and arrow

facing the front) and secure it onto the left base frame

using (4) of the M8 x 25mm hex bolts and spring

washers you removed in step a.

When tightening these bolts, you can use the wrenches

provided in either the fastener pack or the hydraulics

fastener pack – whichever works best for you.

right frame

large

washer

right

swing arm

right base

frame

e. Right Frame/Swing Arm Assembly

Raise the right swing arm and slide it onto the

axle tube. Slide the other large washer onto the

axle tube between the right swing arm and the

right frame. Now raise and slide the right frame

(marked with the R and the arrow facing the

front) onto the axle tube. As you did before,

gently move the axle tube forward and

backwards until the notch “catches” in place

while pushing the right frame on.

Secure everything onto the axle tube with the

M8 x 25mm hex bolt, spring washer and

washer that is left from your fastener pack.

Slip the right frame onto the base frame

assembly and secure it using the M8 x 25mm

hex bolts and spring washers you removed

in step a.

axle tube

with notch down

arrow on axle

pointing left

left

swing arm

left

frame

large

washer

M8 x 25mm

hex bolt,

spring washer

and washer

d. Axle Tube Assembly

Raise the left swing arm up to the top of the left frame.

Slip the axle tube through the swing arm from the right.

Make sure the arrow on the axle tube is pointing left and

the notch on the end of the axle tube is down.

IMPORTANT: Slip a large washer onto the axle between

the swing arm and the left frame before inserting the axle

tube into the left frame.

Slide the axle tube through the left frame. Gently turn the

axle tube back and forth until you feel the notch “catch” in

place. This will tell you that the axle tube is locked into

place. Secure the axle tube with a M8 x 25mm hex bolt,

spring washer and washer from your fastener pack.

M8 x 25mm

hex bolt and

spring washer

front

M8 x 25mm hex

bolt and spring

washer

Step 1 Step 2

Step 3

Gazelle GAZELLE POWER PLUS Assembly Instructions

Brand: Gazelle

Model: GAZELLE POWER PLUS

Type: Assembly Instructions

Improved cardiovascular health
Increased muscle strength and endurance
Reduced body fat
Improved balance and coordination

Download PDF

report

Gazelle GAZELLE POWER PLUS Assembly Instructions

Gazelle GAZELLE POWER PLUS Assembly Instructions

Other documents