Hayward C1200 Owner's manual

Category
Above ground pool accessories
Type
Owner's manual
ISC2002 Rev B
UTILIZE UNICAMENTE REFACCIONES ORIGINALES HAYWARD 1
StarClear
Plus
Cartridge Filter
Owner’s Manual
Models: C751, C900, C1200, C17502
IMPORTANT SAFETY INSTRUCTIONS
NOTA: Versión de idioma español comienza en la página 9
Basic safety precautions s
h
ou
ld
a
l
ways
b
e fo
ll
owe
d
, inc
l
u
d
ing t
h
e fo
ll
owing: Fai
l
ure to fo
ll
ow instructions
can cause severe injury and/or death.
This is the safety-alert symbol. When you see this symbol on your equipment or in this manual, look
for one of the following signal words and be alert to the potential for personal injury.
WARNING warns about hazards that could cause serious personal injury, death or major property
damage and if ignored presents a potential hazard.
CAUTION warns about hazards that will or can cause minor or moderate personal injury and/or
property damage and if ignored presents a potential hazard. It can also make consumers aware of
actions that are unpredictable and unsafe.
The NOTICE label indicates special instructions that are important but not related to hazards.
Hayward Pool Products
620 Division Street, Elizabeth, NJ 07207
Phone: (908) 355-7995
www.hayward.com
Contents
General Warnings……………..……2
General Information……….…..…4
Filter Location & Plumbing..……4
Starting Filter………………………….5
Winterizing Filter…………………….6
Replacement Parts………...…….…7
Warranty ………..………………………7
Registration ……………………..……8
WAR
follo
w
WAR
Suction in
s
severe inju
Hair Entra
Limb Entr
a
cracked, m
Body Suc
t
Eviscerati
sump or s
u
disembow
e
Mechanic
opening of
WAR
o
W
b
e
a
p
o D
o D
o T
h
o N
o R
e
o I
n
g
u
o I
n
WAR
sucti
o
WAR
mater
WAR
repla
c
CAU
T
being
climb
o
heate
r
WAR
start
u
Failur
e
filter
h
death
.
filter
m
positi
o
runni
n
a stea
d
WAR
of pu
m
Befor
e
pool a
pool a
opera
t
syste
m
only a
NING
-
Rea
d
w
instructions
c
NING
– Suc
s
uction outlets
ry and/or deat
h
pment
- Hair c
a
a
pment
- A lim
b
issing, or not s
t
ion Entrapm
e
on/ Disembo
w
u
ction outlet co
v
lment.
a
l Entrapmen
a suction outl
e
NING
- To R
e
W
hen outlets ar
e
e
installed. Su
c
p
art, as measu
r
ual suction fitt
i
ual suction fitt
i
h
e maximum s
y
ever use Pool
o
e
place damag
e
n
addition two
o
u
idelines, follo
w
n
stallation of a
v
NING
Fail
u
o
n outlets can
NING
Fail
u
ial can result i
NING
Suc
t
c
ed at least ev
e
T
ION
Com
p
used as mean
o
n this produc
t
r
s must be posi
NING
– Haz
p, normal ope
r
e
to follow safe
t
ousing and cla
.
Before servici
m
anual air relie
f
o
n to allow sys
t
n
g. Before star
t
d
y stream of w
a
NING
Sep
m
p and/or filter
e
servicing pool
nd spa circulat
nd spa circulat
t
e or test the
c
m
with compres
low pressure (
b
USE ONLY
d
and follo
c
an cause sev
e
tion Entrap
m
and/or suctio
n
h
due to the fol
a
n become ent
a
b
inserted into
ecurely attach
e
e
nt
- A negative
w
elment
- A n
e
v
er which is, d
a
t
- There is pot
e
e
t cover resulti
n
e
duce the ris
e
small enough
c
tion outlets in
r
ed from near
p
ngs shall be pl
ngs shall not b
y
stem flow rate
o
r Spa if any su
c
e
d, broken, cra
c
o
r more suction
w
all National,
v
acuum releas
e
u
re to remove
result in an in
c
u
re to keep su
c
n an increase
t
ion outlet co
m
e
ry seven yea
r
p
onents such
a
s of access to
t
. Closely supe
tioned to prev
e
ardous Pres
s
r
ation, and afte
t
y and operatio
mp due to pre
s
ng pool and s
p
f
valve must b
e
t
em water to re
t
t
ing system pu
m
a
ter (not air or
a
aration Haz
a
components.
and spa circul
ion system if a
ion system unl
e
c
irculation sys
t
sed air can ca
u
b
elow 5 PSI), h
i
HAYWARD G
E
w all instr
u
e
re injury and
/
m
ent Hazard.
n
outlet covers
w
lowing entrap
m
a
ngled in sucti
o
an opening of
a
e
d can result in
pressure appli
e
gative pressu
r
a
maged, broke
n
e
ntial for jewelr
y
n
g in mechanic
a
k of Entrapm
to be blocked
the same plan
p
oint to near po
aced in such l
o
e located on s
e
shall not exce
e
c
tion outlet co
m
c
ked, missing,
o
outlets per pu
m
State, and Loc
a
e
or vent syste
m
pressure test
p
c
rease potenti
c
tion outlet c
o
potential for
s
m
ponents hav
e
r
s or if found t
o
a
s the filtratio
the pool by y
o
rvise children
a
e
nt children fro
m
s
ure.
Pool an
d
r pump shut of
f
n instructions
c
s
sure in the sys
p
a water circula
e
in open positi
o
t
urn back to th
e
m
p, fully open
f
a
ir and water) i
s
a
rd. Failure to
f
Strainer cover
m
ation system, f
system compo
e
ss filter manu
t
em at more t
h
u
se component
i
gh volume blo
w
E
NUINE REPL
A
u
ctions
in t
h
/
or death.
w
hich are, da
m
m
ent hazards:
o
n outlet cover
.
a
suction outle
t
a mechanical
b
e
d to a large p
o
r
e applied dire
c
n
, cracked, mis
y
, swimsuit, ha
a
l entrapment.
ent Hazards
:
by a person, a
m
e (i.e. floor or
w
int.
o
cations and di
s
e
ating areas or
e
d the flow rati
n
m
ponent is da
m
o
r not securely
m
p installed in
a
l codes applic
a
m
, which reliev
e
p
lugs and/or
p
al for suction
o
mponents cle
s
uction entrap
m
e
a finite life, t
o
be damaged
,
n system, pu
m
o
ung children.
a
t all times. Co
m
using them
a
d
spa water circ
f
. Stand clear
o
c
ould result in
v
tem, which co
u
tion system, al
o
n. Before sta
r
e
pool. Do not
f
ilter manual ai
r
s
discharged.
f
ollow safety a
n
m
ust be prope
r
ilters manual a
nent is not ass
al air relief val
v
h
an 50 PSI. D
o
s
to explode,
w
w
er when air p
u
A
CEMENT PA
R
h
is owner’s m
a
m
aged, broken,
.
t
sump or sucti
o
b
ind or swellin
g
o
rtion of the bo
c
tly to the intes
s
sing, or unsec
u
a
ir decorations,
:
minimum of tw
w
all), must be i
stances to avo
i
on the backre
s
n
g of as listed
o
m
aged, broken,
attached sucti
o
accordance w
i
able.
e
s entrapping
s
p
lugs used in
w
entrapment a
s
ar of debris, s
ment as descr
t
he cover/grat
e
, broken, crac
k
m
ps and heate
r
To reduce ris
k
mponents suc
h
a
s a means of a
ulation system
o
f circulation s
y
v
iolent separa
t
u
ld cause prop
e
l system and p
u
r
ting system p
u
change filter c
o
r relief valve.
D
n
d operation in
r
ly secured to p
ir relief valve
m
embled proper
v
e body is in lo
c
o
not purge th
e
w
ith risk of seve
u
rging the pum
R
TS
a
nual and on t
h
cracked, missi
on outlet cove
r
g
of the limb.
o
dy or limbs ca
n
tines through
a
u
red can result
finger, toe or
k
w
o functioning
s
nstalled a mini
i
d “dual block
a
s
t for such seat
i
o
n Table 1.
cracked, miss
i
o
n outlet comp
i
th latest ASM
E
s
uction, is reco
w
interization
o
s
described a
b
uch as leaves
,
r
ibed above.
e
should be in
k
ed, missing,
r
must be posi
k
of injury, do n
h
as the filtrati
o
a
ccess to the p
o
s operate und
e
y
stem equipm
e
t
ion of the pum
e
rty damage, s
e
ump controls
m
u
mp, all system
o
ntrol valve po
s
D
o not close filt
structions cou
l
ump housing
w
m
ust be in ope
n
r
ly, damaged, o
c
ked position i
n
e
system with
c
e
re injury or de
a
p, filter, or pipi
h
e equipment
.
ng, or unsecur
e
r
that is damag
e
n
result in an e
n
a
n unprotected
in evisceratio
n
k
nuckle to be c
a
s
uction outlets
mum of three
f
a
ge” by a user.
i
ng areas.
i
ng, or not sec
u
onents immed
i
E
, APSP Standa
r
mmended.
o
f the pool/sp
a
b
ove.
,
dirt, hair, pa
p
spected frequ
or not securel
y
tioned so as t
ot permit child
o
n system, pu
m
o
ol.
e
r hazardous p
r
e
nt during pum
p
p housing and
e
vere personal
m
ust be in off p
o
valves must b
e
s
ition while sy
s
er manual air r
e
l
d result in viol
e
w
ith strainer co
v
n
position. Do
n
r missing. Do
n
n
filter upper b
o
c
ompressed a
a
th to anyone n
i
ng.
.
Failure to
e
d can cause
e
d, broken,
n
trapment.
suction outlet
n
/
a
ught in an
per pump mus
t
f
eet (3’) [1 met
e
u
rely attached.
i
ately.
r
ds and CPSC
a
from the
p
er and other
ently and
y
attached.
o prevent thei
ren to use or
m
ps, and
r
essure during
p
start up.
cover, and/or
injury, or
o
sition and
e
set in a
s
tem pump is
e
lief valve unti
l
e
nt separation
v
er lock ring.
n
ot operate
n
ot operate
o
dy. Never
ir. Purging the
earby. Use
2
t
e
r]
r
l
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 3
WARNING Risk of Electric Shock. All electrical wiring MUST be in conformance with applicable local codes,
regulations, and the National Electric Code (NEC). Hazardous voltage can shock, burn, and cause death or serious property
damage. To reduce the risk of electric shock, do NOT use an extension cord to connect unit to electric supply. Provide a
properly located electrical receptacle. Before working on any electrical equipment, turn off power supply to the equipment.
To reduce the risk of electric shock replace damaged wiring immediately. Locate conduit to prevent abuse from lawn
mowers, hedge trimmers and other equipment. Do NOT ground to a gas supply line.
WARNING Risk of Electric Shock Failure to ground all electrical equipment can cause serious or fatal electrical shock
hazard. Electrical ground all electrical equipment before connecting to electrical power supply.
WARNING Risk of Electric Shock Failure to bond all electrical equipment to pool structure will increase risk for
electrocution and could result in injury or death. To reduce the risk of electric shock, see installation instructions and
consult a professional electrician on how to bond all electrical equipment. Also, contact a licensed electrician for
information on local electrical codes for bonding requirements.
Notes to electrician: Use a solid copper conductor, size 8 or larger. Run a continuous wire from external bonding lug to
reinforcing rod or mesh. Connect a No. 8 AWG (8.4 mm
2
) [No. 6 AWG (13.3 mm
2
) for Canada] solid copper bonding wire to the
pressure wire connector provided on the electrical equipment and to all metal parts of swimming pool, spa, or hot tub, and metal
piping (except gas piping), and conduit within 5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub.
IMPORTANT - Reference NEC codes for all wiring standards including, but not limited to, grounding, bonding and other general
wiring procedures.
WARNING Risk of Electric Shock . The electrical equipment must be connected only to a supply circuit that is
protected by a ground-fault circuit-interrupter (GFCI). Such a GFCI should be provided by the installer and should be tested on a
routine basis. To test the GFCI, push the test button. The GFCI should interrupt power. Push reset button. Power should be
restored. If the GFCI fails to operate in this manner, the GFCI is defective. If the GFCI interrupts power to the electrical equipment
without the test button being pushed, a ground current is flowing, indicating the possibility of an electrical shock. Do not use this
electrical equipment. Disconnect the electrical equipment and have the problem corrected by a qualified service representative
before using.
CAUTION – HAYWARD
®
pumps are intended for use with permanently-installed pools and may be used with hot tubs and
spas if so marked. Do not use with storable pools. A permanently-installed pool is constructed in or on the ground or in a
building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is capable of being
readily disassembled for storage and reassembled to its original integrity.
WARNING Risk of Hyperthermia. To avoid hyperthermia the following “Safety Rules for Hot Tubs” are recommended by
the U.S. Consumer Product Safety Commission.
1. Spa or hot tub water temperatures should never exceed 104°F [40°C]. A temperature of 100°F [38°C] is
considered safe for a healthy adult. Special caution is suggested for young children. Prolonged immersion in
hot water can induce hyperthermia.
2. Drinking of alcoholic beverages before or during spa or hot tub use can cause drowsiness, which
could lead to unconsciousness and subsequently result in drowning.
3. Pregnant women beware! Soaking in water above 100°F [38°C] can cause fetal damage during the
first three months of pregnancy (resulting in the birth of a brain-damaged or deformed child). Pregnant women
should adhere to the 100°F [38°C] maximum rule.
4. Before entering the spa or hot tub, users should check the water temperature with an accurate ther-
mometer; spa or hot tub thermostats may err in regulating water temperatures by as much as 4°F (2.2°C).
5. Persons taking medications, which induce drowsiness, such as tranquilizers, antihistamines or anti-
coagulants, should not use spas or hot tubs.
6. If the pool/spa is used for therapy, it should be done with the advice of a physician. Always stir pool/ spa
water before entering the pool/spa to mix in any hot surface layer of water that might exceed healthful
temperature limits and cause injury. Do not tamper with controls, because scalding can result if safety controls
are not in proper working order.
7. Persons with a medical history of heart disease, circulatory problems, diabetes or blood pressure
problems should obtain a physician’s advice before using spas or hot tubs.
8. Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above
normal body temperature of 98.6°F [37°C]. The symptoms of Hyperthermia include: drowsiness, lethargy,
dizziness, fainting, and an increase in the internal temperature of the body.
The effects of Hyperthermia include:
1. Unawareness of impending danger.
2. Failure to perceive heat.
3. Failure to recognize the need to leave the spa.
4. Physical inability to exit the spa.
5. Fetal damage in pregnant women.
6. Unconsciousness resulting in danger of drowning.
SAVE THESE INSTRUCTIONS
ATTENTION INSTALLER: THIS MANUAL CONTAINS IMPORTANT INFORMATION ON THE OPERATION,
AND SAFE USE OF THIS EQUIPMENT.
THIS MANUAL IS INTENDED FOR THE END USER OF THIS PRODUCT
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 4
GENERAL INFORMATION
The Hayward StarClear
Plus filter is a high performance swimming pool filter with a residential filtration rating of 4,500 gallons
(17 kl) per hour (C751), 5,400 gallons (20.5 kl) per hour (C900), or 7,200 gallons (27.3 kl) per hour (C1200,and C17502).
Manufactured from durable, corrosion-proof materials, they are designed for continuous or intermittent operation, for
installation above or below the pool water line, for fresh or saltwater swimming pools or spas. StarClear Plus filters utilize a
reusable single element, reinforced polyester filter cartridge to provide a high degree of water clarity with minimum care. Their
unique design is such that no tools are needed to remove or replace the cartridge in the filter assembly. Simply spin off the
locking knob, lift off the filter cover and remove the cartridge. It's that easy.
PUMP SELECTION AND LOCATION
To power your StarClear Plus filter, select a continuous duty pump designed for swimming pool or spa service.
It is important to first determine where your pump and filter will be located. If above the water line, a self-priming pump must
be used. Self-priming pumps such as Hayward's Super Pump
®
, Super II, or TriStar have the ability to lift water
from a lower level and prime automatically.
Select a pump appropriate for your application. Take into consideration, operation of hydrotherapy fittings, automatic
cleaners, required turnover rates and losses in the system. A dealer can help you select the proper size pump for your
system.
FILTER LOCATION
1. Since plumbing fittings offer a resistance to water flow, position the filter as close to the swimming pool as local codes
allow. Keep the number of fittings to a minimum. Select a well-drained area, one that will not flood when it rains.
2. Set the filter on a solid level surface. Allow a minimum top clearance for cartridge removal of 19" (483mm) for the C751 and
C900, 25" (635mm) for the C1200, and allow 30" (762mm) for the C17502. Be sure the filter, pump, drain & pressure
gauge are accessible for convenient operation. (Please: See Chart on Following Page)
3. Position the filter so the tank can drain by gravity.
4. If practical, place pump and filter in the shade to shield it from continuous, direct heat from the sun.
PLUMBING
1. Choose and use 1-1/2" or 2" piping. When making permanent connections, be sure to provide unions for easy servicing.
2. Refer to the diagrams above for basic suggested placement of valves. Ball valves are recommended where needed. While
systems vary, the main consideration is to provide the desired control of water flow from the pool to the pump and filter,
and back to the pool. When the filter is located below water level, provide valves to prevent back flow of water to the
filter during cleaning and routine servicing.
3. Plumbing on the StarClear Plus filter is 1-1/2", or 2" N.P.T., or socket (solvent weld). When making threaded connections to
the filter use plastic adapters. Apply three turns of Teflon tape (or use special plastic pipe sealant) to male threads.
Screw the fitting into the thread hand tight; then using a wrench, tighten one more full turn. Additional tightening is
unnecessary and could result in a broken or a damaged filter.
4. Connect the pool suction plumbing between the skimmer, pool outlet, etc. and the pump.
5. Install the pool return plumbing.
6. If the pressure gauge is not installed, apply three wraps of Teflon tape to the gauge threads, and
carefully
screw the gauge
into the threaded hole in the filter head.
7. A filter drain plug is furnished with each filter and is all that is needed for complete filter draining. A manual air relief valve
is furnished to aid in bleeding off unwanted air when starting the filter. An internal auto air relief system in the filter
removes air when the pump is in operation.
8. All electrical connections should be made in accordance with local codes.
9. Check for joint leaks when first operating the system.
10. Refer to pump instruction booklet for pump information.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 5
STARTING THE FILTER
Be sure filter drain plug is installed and closed. Open manual air relief
valve a few turns and open the suction and return valves (when used).
CAUTION: All suction and discharge valves must be
open when starting the system. Failure to do so could
cause severe personal injury and/or property
damage. Be sure locking knob is secure (hand tighten-only slight pressure is required).
Stand clear of the filter. Prime and start the pump, following the manufacturer's instructions. Air trapped in the system
will automatically vent to the pool and out air relief valve. Close air relief valve as soon as air is vented, as indicated by water
flow.
FILTERING
Filtration starts as soon as flow is steady through the filter. As the filter cartridge removes dirt from the pool water, the
accumulated dirt causes a resistance to flow. As a result, the gauge pressure will rise and the flow will decrease. When the
pressure rises 7-10 psi (.49-.70 Bar) above the starting pressure, or when flow decreases below desired rate, clean or replace
the filter cartridge.
CLEAN / REPLACE CARTRIDGE
REMOVING CARTRIDGE ELEMENT
1. Shut off the pump.
2. If filter is located below water level, close valves or block off suction & discharge lines to prevent backflow of water from
the pool.
3. Remove drain plug and allow water to drain from filter. Close drain plug. (To assist draining process; open air vent a few
turns.)
4. Unscrew and remove locking knob (counterclockwise direction) and carefully lift off top cover to gain access to filter
cartridge.
5. Lift out cartridge and clean. Or, replace with clean, spare cartridge. (See Cleaning Cartridge.)
REINSTALLING CARTRIDGE ELEMENT
1. Clean any collected debris from the bottom of filter body.
2. Carefully replace cartridge element over tie rod and into filter body ensuring that the cartridge sits evenly on the collector
hub in bottom of filter body.
3. Place cover on filter body (being sure filter head 0-ring is in place and clean). Fit tie rod end through center hole.
4. Tighten locking knob in clockwise direction. (Hand tight only.)
5. Proceed as in STARTING THE FILTER.
CLEANING CARTRIDGE
The cartridge filter element can be cleaned by washing inside and out with a garden hose. (The cartridge is easier to clean
when dry.) After hosing the cartridge, for best results, allow cartridge to dry and carefully brush pleated surface areas to
remove fine particles. Do not pressure wash, as it can damage the filter element.
Algae, suntan oil and body oils can form a coating on the cartridge pleats which may not be thoroughly removed by hosing. To
remove such materials, soak the cartridge in a solution of filter element cleaner (various brands available at pool dealer).
Follow manufacturer's directions for use, paying close attention to any Warnings on the package. Rinse the element
thoroughly with water from a garden hose before reinstalling in the filter.
A spare cartridge filter element is an excellent investment. It provides convenience and ensures that your filter will always
be ready to operate at peak efficiency.
1. Hayward cartridges are specially designed and engineered for use in StarClear Plus filters. For best results, use only
genuine Hayward StarClear cartridges in your filter. Order
Model No. CX760RE, CX900RE , CX1200RE, or CX1750RE,
from
your dealer. The Hayward name is your guarantee of quality.
VACUUMING
Vacuuming can be performed directly into the filter whenever needed. Clean cartridge after vacuuming, if required.
REQUIRED CLEARANCE
SIDE ABOVE
IN CM IN CM
C751 18 46 19 48
C900 18 46 19 48
C1200(2) (S) 18 46 25 64
C17502(S) 18 46 30 76
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 6
WINTERIZING (Filter)
In areas where sub-freezing temperatures can be expected, the filter should be fully drained and/or removed from its,
operating location and stored indoors. Remove and clean cartridge. Reinstall cartridge in filter tank. Tighten locking knob
only a few turns when storing.
SERVICE AND REPAIRS
Consult your local authorized Hayward dealer or service center. No returns may be made directly to the factory without the
expressed written authorization of Hayward Pool Products.
SUGGESTED POOL CHEMISTRY LEVELS
pH 7.2 to 7.8
TOTAL ALKALINITY 80 to 120 ppm
CALCIUM HARDNESS 200 to 400 ppm
COMBINED CHLORINE .2 ppm Maximum
CHLORINE (STABILIZED) 1.0 to 3.0 ppm
CHLORINE STABILIZER
(Cyanuric Acid)
60 to 80 ppm
PROBLEM SOLVING LIS
T
LOW WA
T
ER FLOW SHORT FILTER CYCLES
POOL WATER WON’T CLEAR UP
REMED
Y
Check skimmer and pump,
strainer baskets for debris.
Check for algae in pool and treat
as required.
Check chlorine, pH and total
alkalinity levels and adjust as
required.
Check for restrictions in intake
and discharge lines.
Be sure chlorine and pH levels
are in proper range (adjust as
required).
Be sure flow rate through filter is
sufficient.
Check for air leak in intake line
(indicated by bubbles returning
to pool).
Operate filter for longer periods.
Clean Filter Cartridges
(see Page 5)
MODEL EFFECTIVE FILTRATION AREA
DESIGN FLOW RATE
RESIDENTIAL
FT
2
M
2
GPM LPM
C751 75 7.0 75 284
C900 90 8.4 90 341
C1200(2
)
(S) 120 11.1 120 454
C17502(S) 175 16.3 120 454
Maximum Working Pressure for all Models 50 PSI, (3.45 Bar)
M
o
REF
NO
la
1b
2
3
4
5
6a
6b
6c
7
8a
8b
8c
9
10
a
10
b
10
c
10
d
11a
11b
11c
12
a
12
b
12c
13
14
15
H
A
To o
r
peri
o
The l
beco
unfo
r
Proo
f
sole
To o
b
Hay
w
Hay
w
or re
p
The
H
resp
e
The
e
warr
a
resp
o
Som
e
limit
a
o
dels C751, C9
0
.
PART N
O
CX900G
CX1750G
CX900H
CX900W
CX900J
CX900D
CX900B
CX1200B
CX1750B
CX900
F
CX900AA
CX1200A
A
CX1750A
A
ECX2712
B
a
CX760RE
b
CX
9
00RE
c
CX1200R
E
d
CX1750R
E
CX800Z2
CX1100Z
2
CX1750Z
2
a
CX800Z4
b
CX1100Z
4
CX1750Z
4
CX250Z1
4
CX900K
ECX1322
A
A
YWARD
®
r
iginal purchaser
s
o
d of ONE (1) yea
r
imited warranty
e
me defective du
r
r
eseen delays, w
f
of purchase is r
determination o
f
b
tain warranty se
w
ard Authorized
S
w
ard shall not be
p
air.
H
ayward Pool pr
o
e
ctive manufact
u
e
xpress limited
w
a
nties expressed
o
nsible for any c
o
e
states do not a
a
tion may not ap
*Su
p
ersed
e
P
A
0
0(2)(S), C12
0
.
Lockin
g
Lockin
g
0-Ring
Washe
r
E-Ring
Guide
C
Filter H
e
Vl (C
Filter H
e
(
Filter H
e
Filter H
e
Filter B
A
Filter B
A
2 Filter B
B
1 Pressu
r
Cartrid
g
Cartrid
g
E
Cartrid
g
E
Cartrid
g
Tie Rod
2
Tie Rod
2
Tie Rod
Auto Ai
r
4
Auto Ai
r
4
Auto Ai
r
4
A
1/2" Dr
a
2" PVC
S
Set of 2
A
Directio
Pool Pro
d
s
of this equipm
e
r
from the date o
f
e
xcludes damag
e
r
ing the warranty
ithout charge.
equired for warr
a
f
the purchase d
a
rvice, please co
n
S
ervice Center pl
e
responsible for
c
o
ducts warranty
d
u
rer will apply.
w
arranty above c
o
or implied, incl
u
o
nsequential, sp
e
l
low a limitation
o
ply to you. This
w
e
s all
p
revious
p
USE ONLY
A
RTS
0
0(2)(S),and
C
DESCRIPTIO
g
Knob
g
Knob
r
C
one
e
ad w/Directi
o
)
e
ad w/Directi
o
)
e
ad w/Directi
o
e
ad 0-Ring
ody-C751,C9
0
ody-C1200)
ody-C17502)
r
e Gauge
g
e Element (C
7
g
e Element (C
9
g
e Element (C
1
g
e Element (C
1
(C900)
(C1200)
(C1750)
r
Relief Tube
(
r
Relief Tube
(
r
Relief Tube
(
a
in Plug with
O
S
ocket Conne
(Not Shown)
nal Vent Valv
e
d
ucts Lim
e
nt, Hayward Po
o
f
purchase, when
e
from freezing, n
period shall be
r
a
nty service. In t
h
a
te.
n
tact the place of
e
ase visit us at
w
c
artage, removal,
d
oes not apply to
o
nstitutes the en
t
u
ding warranties
o
e
cial or incident
a
o
n how long an i
m
w
arranty gives y
o
ublications.
HAYWARD G
E
C
17502(S) Filt
e
N
R
E
o
nal Vent
o
nal Vent
o
nal Vent
0
0)
7
51
)
9
00)
1
200)
1
750)
(
C900)
(
C1200)
(
C1750)
O
-Ring
ctor
e
w/O-Ring
ited War
r
o
l Products, Inc.
w
used in single f
a
egligence, impr
o
r
epaired or repla
c
h
e event proof of
purchase or the
w
ww.hayward.co
m
repair or install
a
components ma
t
ire warranty of H
o
f merchantabili
t
a
l damages of an
y
m
plied warranty
l
o
u specific legal r
E
NUINE REPL
A
e
rs
NO.
E
Q’D.
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
r
anty
w
arrants its filter
s
a
mily residential
o
per installation,
c
ed, at our optio
n
purchase is not
a
nearest Hayward
m
.
a
tion labor or an
y
nufactured by ot
h
ayward Pool Pro
d
t
y or fitness for a
y
nature.
l
asts, or the excl
u
ights, and you m
A
CEMENT PA
R
s
to be free from
d
applications.
improper use or
n
, within 90 days
a
vailable, the m
a
d
Authorized Ser
v
y
other such cost
s
h
ers. For such p
r
d
ucts with respe
c
particular purpo
u
sion of incident
ay also have oth
e
R
TS
d
efects in materi
care or any Acts
o
of the receipt of
a
nufacturing dat
e
v
ice Center. For a
s
incurred in obt
a
r
oducts, the war
r
c
t to its’ pool pro
d
se. In no event s
h
al or consequen
t
e
r rights, which
v
als and workma
n
o
f God. Parts tha
t
defective produ
c
e
of the product
w
a
ssistance on yo
u
a
ining warranty r
e
r
anty established
d
ucts and is in li
e
h
all Hayward Po
o
t
ial damages, so
t
v
ary from state to
Haywar
d
620
Eliza
b
n
ship for a
t
fail or
c
t, barring
w
ill be the
u
r nearest
e
placements
by the
e
u of all other
o
l products be
the above
state.
d
Pool Products
Division Street
b
eth
,
N
J
0
7
20
7
7
Dat
e
Initi
Pu
m
Filt
e
Re
t
Plea
s
First
Stre
e
City
_
Pho
n
E-M
a
Seri
a
Mod
Pool
If yo
u
nece
Inste
seria
Ple
a
Mail
Attn
:
Or R
E
----
-
St
a
e
of Install
a
al Pressur
e
m
p Model _
_
e
r Model__
_
t
ain this Warra
n
s
e Print Clear
l
Name_____
_
e
t Address_
_
_
__________
_
n
e Number_
_
a
il Address_
_
a
l Number
el Number__
_
Capacity___
_
u
r product con
ssary to comp
ad, complete
w
l number that
a
se include me o
n
to: Hayward
:
Warranty De
p
E
GISTER YOU
R
DETACH
H
-
---------------
-
a
rClear
Hayward
© 2016
H
a
tion____
_
e
Gauge R
e
_
________
_
________
n
ty Certificate
i
l
y:
_
__________
_
__________
_
_
_________
_
_
__________
_
_
__________
_
_
__________
_
_
__________
_
tains compon
e
lete warranty
r
w
arranty regis
is located on
t
n
all e-mail com
m
Pool Product
s
p
t
R
WARRANTY
O
H
ERE: Fill out b
o
-
---------------
-
Plus C
a
and StarClear Plus a
H
ayward Industries, I
n
USE ONLY
_
________
_
e
ading (Cle
________
_
________
_
i
n a safe and c
o
_
___ Last Na
_
__________
_
_
_______ Sta
t
_
________ P
u
_
__________
_
___________
_
_
(U.S. Gallons
)
e
nts that have
r
egistration fo
r
tration only f
o
t
he outside of
m
unications rega
r
s
, 620 Divisio
n
O
N-LINE AT W
W
o
ttom portion c
o
-
---------------
a
rtridge
F
R
re registered tradem
a
n
c.
HAYWARD G
E
Produc
t
(Retain
f
_
______
an Filter)_
_
_
____
_
____
o
nvenient loca
t
me________
_
_________
_
t
e_________
_
u
rchase Date
_
__________
_
_
__________
_
)
individual se
r
r
those indivi
d
r the overall p
the product p
r
ding Hayward
®
E
n
Street, Eliz
a
W
W.HAYWAR
D
o
mpletely and m
----------------
F
ilter
e
g
ister onlin
a
rks of Hayward Ind
u
E
NUINE REPL
A
t
Registr
a
f
or Your Reco
r
_
________
_
Horse
Serial
t
ion for your re
c
__________
_
_
__________
_
_
_ Zip_____
_
_
_________
_
_
__________
_
_
__________
_
r
ial numbers,
i
d
ual compone
n
roduct, using
a
ckaging.
E
quipment or pro
m
a
beth, NJ 072
0
D
.COM
ail within 10 da
y
---------------
-
e at www.ha
y
u
stries, Inc.
A
CEMENT PAR
a
tion
rds)
_
________
_
power ___
_
Number _
_
c
ords
_
______
_
_____
_
______
_
______
_
_____
_
_____
i
t is not
n
ts.
the
m
otions.
07
y
s of purchase/
i
-
---------------
-
Wa
r
y
ward.com
Y
ear
s
< 1
Purc
h
Bu
i
Com
p
Addr
e
City
_
Phon
Type
Co
Ot
N
e
Insta
In
TS
________
_
_
________
_
________
_
installation or r
e
-
---------------
-
r
ranty C
a
s
Pool has been i
year 1-3
h
ased from____
_
i
lder Retailer
p
any Name____
_
ess___________
_
_
_____________
_
n
e____________
_
of Pool:
o
ncrete/Gunite
her___________
_
e
w Installation
a
llation for:
Ground Ab
o
_
_
________
_
_
_______
_
e
gister online.
-
---------------
a
rd Regi
n service
4-5 6-10
1
_
_____________
_
Pool Service
_
_____________
_
_
_____________
_
_
_____ State____
_
_
_____________
_
Vinyl Fib
e
_
_____________
_
Rep
l
o
ve Ground
_
______
_
______
--------------
stration
1
1-15 >15
_
__________
Internet/Catalo
g
_
_____________
_
_
_____________
_
Zip_________
_
_
_____________
_
e
rglass
_
___
l
acement
Spa
8
_
_
UTILIZE UNICAMENTE REFACCIONES ORIGINALES HAYWARD 16
Guarde este Certificado de Garantía para sus records en un lugar seguro y conveniente.
SwimClear™ Plus
Cartridge Filter
Tarjeta de registro de la garantía
Regístrese por Internet en www.hayward.com
Por favor, escriba claramente con letra de molde:
Nombre ___________________________________ Apellido _______________________________________
Dirección _________________________________________________________________________________
Ciudad __________________________________ Estado ____________ Código postal _________________
Número de teléfono: _____________________________ Fecha de compra: ___________________________
Dirección de su correo electrónico ______________________________________________________________
Número de serie del producto
(Número de 10 a 17 dígitos)
Número de modelo: __________________________
Envíe a: Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207 Attn: Warranty Dept.
Registro de su producto
(Guarde para sus récords)
_____________________________________________________________________________________________________________________________________
Fecha de Instalación___________________
Lectura Inicial del medidor de presión_____________________
Modelo de Bomba________________________ Caballos de Fuerza_____________________________
Modelo de Filtro___________________________ Número de serie_______________________________
Hayward and StarClear Plus are registered trademarks of Hayward Industries, Inc.
© 2016 Hayward Industries, Inc.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Hayward C1200 Owner's manual

Category
Above ground pool accessories
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages