Potter MAS Agent Release Fire Suppression Pull and Abort Station User manual

Potter
Brand
Potter
Model
MAS Agent Release Fire Suppression Pull and Abort Station
Type
User manual

Potter MAS Agent Release Fire Suppression Pull and Abort Station:

The Potter MAS Agent Release Fire Suppression Pull and Abort Station is a UL and cUL Listed & CSFM Listed device designed for indoor use only. It consists of a manual pull station and a push button abort switch. The pull station has a 0.5 Amp @ 30 VDC single pull action, while the abort switch has a 2.5 Amps @ 24 VDC (5 mA minimum) normally open, momentary type. The station has dedicated terminal connectors and includes a backbox suitable for RMS pull stations.

Potter MAS Agent Release Fire Suppression Pull and Abort Station:

The Potter MAS Agent Release Fire Suppression Pull and Abort Station is a UL and cUL Listed & CSFM Listed device designed for indoor use only. It consists of a manual pull station and a push button abort switch. The pull station has a 0.5 Amp @ 30 VDC single pull action, while the abort switch has a 2.5 Amps @ 24 VDC (5 mA minimum) normally open, momentary type. The station has dedicated terminal connectors and includes a backbox suitable for RMS pull stations.

MFG. #5401519 - REV B
01/13
PRINTED IN USA PAGE 1 OF 1
MAS: Agent Release/Fire Suppression
Pull and Abort Station
Potter Electric Signal Company, LLC • St. Louis, MO • Phone: 866-956-0988/Canada 888-882-1833 • www.pottersignal.com
Description
The Potter MAS Switch is designed to be used with any releasing
system. The device consists of a manual pull station and a push button
abort switch. This device is designed for indoor use only.
The MAS-Agent Release/Fire Suppression & Abort Station was
developed as a way to mount manual pull stations and abort buttons in
a convenient and attractive NEMA 1 rated metal enclosure. This unit
is capable of being surface mounted or ush mounted (using 5370559
Bezel)
The RMS-1T Release Pull Station (Red, As Shown) and RMS-1T
(Yellow) are single pole, single throw die-cast aluminum electrical
switch. This pull station has a 0.5-amp snap action switch and
dedicated terminal block for the ease of wire connections. All of the
metal is completely coated to inhibit corrosion and provide for a
uniform and quality nish. The standard model has a hex key reset.
Electrical wiring diagrams are included with the product.
There are other Listed pull stations available upon request.
RMS-1T
RMS-2T
RMS-3T
RMS-6T
Contact Potter for available models.
The abort switch is a normally open, momentary type.
Operation
The Potter single action series of pull stations operate by pulling the
white operating handle straight down and the handle will lock into
place. The station is reset by opening the front and placing the handle
in the normal non-pulled position. The abort switch is a momentary
push button.
Ordering Information
MAS-R: Red Agent Release Pull Station 3001010
MAS-Y: Yellow Fire Suppression Pull Station 3001011
MAS-MP: Mounting Plate for Manual Station 3001012
-Includes Abort Switch and backbox suitable
for RMS pullstations identied below.
Accessory: Flush Mount Bezel 5370559
UL and cUL Listed & CSFM Listed
Dimensions: 6" x 6" x 3"
NEMA 1 Indoor Use Only
All Wiring Power Limited
Pull Station Specications:
0.5 Amp @ 30 VDC
Single Pull Action
Double Action models are available
Terminal Connectors
Optional Use Glass break rod
Abort Push Button Specications:
2.5 Amps @ 24 VDC (5 mA minimum)
Normally Open, Momentary Type
Engineering Specications
The contractor shall furnish and install a combination Agent Release/
Fire Suppression pull station and abort switch. The pull station shall
be die cast metal with a "T" type pull handle that is ADA compliant.
Once activated, the handle cannot be restored to the normal position
without opening the front of the pull station. Opening the pull station
in a normal state shall cause the device to activate. The abort button
shall be a momentary push button type switch. The pull station and
abort switch shall be combined on a single stainless steel plate. The
unit shall come with a back box for surface mounting and shall be
capable of being ush mounted with an available bezel.
Mounting
Surface Mount: Electrical Box (NEMA 1 screw cover): 6" X 6" X 3"
Flush Mount Bezel: 7 ½" x 7 ½"
Accessory: Flush Mount Bezel
Stock Number: 5370559
firealarmresources.com
  • Page 1 1

Potter MAS Agent Release Fire Suppression Pull and Abort Station User manual

Potter
Brand
Potter
Model
MAS Agent Release Fire Suppression Pull and Abort Station
Type
User manual

Potter MAS Agent Release Fire Suppression Pull and Abort Station:

The Potter MAS Agent Release Fire Suppression Pull and Abort Station is a UL and cUL Listed & CSFM Listed device designed for indoor use only. It consists of a manual pull station and a push button abort switch. The pull station has a 0.5 Amp @ 30 VDC single pull action, while the abort switch has a 2.5 Amps @ 24 VDC (5 mA minimum) normally open, momentary type. The station has dedicated terminal connectors and includes a backbox suitable for RMS pull stations.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents