Reznor VPT Installation guide

Revision: VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

GAS-FIRED RADIANT HEATER INSTALLATION, OPERATION,

AND MAINTENANCE

Supersedes: VCS-VCT-VPS-VPT-IOM (05-23) 1042552-0

MODELS VCS, VCT, VPS, AND VPT

⚠ DANGER ⚠

FIRE OR EXPLOSION HAZARD

• Failure to follow safety warnings exactly could result in serious injury, death, or property

damage.

• Improper installation, adjustment, alteration, service, or maintenance can cause serious injury,

death, or property damage.

• Installation and service must be performed by a qualified installer, service agency, or the

gas supplier.

• Be sure to read and understand the installation, operation, and service instructions in this

manual.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a phone remote from the building. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

DO NOT DESTROY. PLEASE READ CAREFULLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

2VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

TABLE OF CONTENTS

GENERAL INFORMATION ................................................................... 3

References .............................................................................. 3

Important Safety Information................................................................. 3

Warranty ................................................................................ 4

Model Application ......................................................................... 4

Certification .............................................................................. 4

Installation Codes ......................................................................... 5

Heater Location........................................................................... 5

Mounting Height Requirements ............................................................ 5

Hazards of Chlorine ..................................................................... 5

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Clearances .............................................................................. 6

Weights ................................................................................. 8

SYSTEM CONFIGURATIONS ................................................................. 8

INSTALLATION ........................................................................... 19

Unpacking and Inspection.................................................................. 19

Pre-Installation Checklist................................................................... 19

Heater Assembly......................................................................... 19

Heater Suspension ....................................................................... 23

Vent Connections ........................................................................ 24

Vertical Venting ....................................................................... 25

Horizontal Venting ..................................................................... 26

Fresh Air Intake ....................................................................... 28

Piping Connections ....................................................................... 28

Gas Supply Pressure ................................................................... 28

Gas Supply Piping ..................................................................... 29

Supply Piping Connections .............................................................. 30

Electrical Connections..................................................................... 32

CONTROLS .............................................................................. 32

Pressure Switch ......................................................................... 32

Combination Gas Valve.................................................................... 32

Ignition Controller ........................................................................ 32

OPERATION ............................................................................. 33

Pre-Startup Checklist ..................................................................... 33

Startup................................................................................. 34

Measure and Adjust Manifold Gas (Outlet) Pressure ............................................. 34

Post-Startup Checklist..................................................................... 35

MAINTENANCE........................................................................... 36

Service Checklist......................................................................... 36

Maintenance Procedures .................................................................. 37

Burner Maintenance .................................................................... 37

Fan and Motor Assembly Maintenance ..................................................... 38

Combination Gas Valve Maintenance ...................................................... 39

Ignition Controller Replacement ........................................................... 41

Pressure Switch Replacement ............................................................ 41

TROUBLESHOOTING...................................................................... 42

General Troubleshooting................................................................... 42

Troubleshooting Using Ignition Controller ...................................................... 42

APPENDIX: MULTIPLE UNIT WIRING CONNECTIONS (MODELS VCT AND VPT) ..................... 43

INSTALLATION RECORD (TO BE COMPLETED BY INSTALLER) .................................. 44

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

GENERAL INFORMATION

•This heater has been tested for capacity and efficiency so as to provide many years of safe and dependable comfort

providing it is properly installed and maintained. With regular maintenance, this unit will operate satisfactorily year

after year. Abuse, improper use, and/or improper maintenance can shorten the life of the appliance and create

unsafe hazards.

•To achieve optimum performance and minimize equipment failure, it is recommended that periodic maintenance

be performed on this unit. The ability to properly perform maintenance on this equipment requires certain tools

and mechanical skills.

•This manual applies only to the models listed. Accessories referenced may not apply to all models.

References

Table 1. Related Technical Manuals Available from Factory Distributor

Type Form PN*

Replacement parts VCS-VCT-VPS-VPT-RPL 1042553

Hanger kit installation VCS-VCT-VPS-VPT-CK11-CK31 D270722

Turnbuckle kit installation VCS-VCT-VPS-VPT-CK12-CK40 270712

Combustion air inlet kit installation VCS-VCT-VPS-VPT-DE1-DE2 270688

High-elevation conversion kit installation VCS-VCT-VPS-VPT-DJ20 270687

Gas conversion kit installation VCS-VCT-VPS-VPT-DL2 1042554

*Also available at www.reznorhvac.com.

Important Safety Information

Please read all information in this manual thoroughly and become familiar with the capabilities and use of your

appliance before attempting to operate or maintain this unit. Pay attention to all dangers, warnings, cautions, and

notes highlighted in this manual. Safety markings should not be ignored and are used frequently throughout to

designate a degree or level of seriousness.

DANGER: A danger statement describes a potentially hazardous situation that if not avoided, will result in severe

personal injury or death and/or property damage.

WARNING: A warning statement describes a potentially hazardous situation that if not avoided, can result in severe

personal injury and/or property damage.

CAUTION: A caution statement describes a potentially hazardous situation that if not avoided, can result in minor

or moderate personal injury and/or property damage.

NOTE: A note provides important information that should not be ignored.

4VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

GENERAL INFORMATION—CONTINUED

Important Safety Information—Continued

⚠ WARNING ⚠

• Gas-fired appliances are not designed for use in hazardous atmospheres containing flammable

vapors or combustible dust, in atmospheres containing chlorinated or halogenated hydrocarbons,

or in applications with airborne silicone substances.

• Should overheating occur, or the gas supply control system fail to shut off the flow of gas, shut

off the manual gas valve to the unit before shutting off the electrical supply.

• Do not use this appliance if any part has been under water. Immediately call a qualified service

technician to inspect the appliance and replace any gas control that has been under water.

• Installation should be done by a qualified agency in accordance with these instructions. The

qualified service agency installing this heater is responsible for the installation.

• This appliance is not intended for use by persons with reduced physical, sensory, or mental

capabilities or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the appliance.

⚠ CAUTION ⚠

• Never rest anything—especially a ladder—against the heater.

• To prevent damage to the unit or to its internal components, it is recommended that two wrenches

be used when loosening or tightening nuts. DO NOT OVERTIGHTEN!

Warranty

Refer to the limited warranty form in the literature bag provided with the unit. The warranty is void if:

•Wiring is not in accordance with the diagram furnished with the heater.

•The unit is installed without proper clearance to combustible materials.

•Correct turbulator or burner insert is missing or incorrectly installed.

Model Application

Table 2. Model Application

Model Burner Tube Length (Feet) Application

VCS Single-stage 20–80 Harsh environment, indoor non-

residential or outdoor

VCT Low- and high-fire 20–70

VPS Single-stage 20–80 Indoor commercial/industrial

VPT Low- and high-fire 20–70

Certification

•These heaters are approved for use in the United States and Canada by the Canadian Standards Association

(CSA). Models VCS and VCT are designed for outdoor or non-residential indoor spaces. Models VPS and VPT are

designed for non-residential indoor spaces. Standard heaters are approved for installation elevations of 0–2,000

feet (0–610 meters) for the US and 0–4,500 feet (0–1,370 meters) for Canada. Conversion kits are available for

installations above these elevations in the US.

•All models and unit sizes are available for use with natural gas. Unit sizes 060–170 are available for use with

propane gas. Gas conversion kits are available for converting natural gas units to propane.

•The type of gas, the gas input rate, and the electrical supply requirements are shown on the heater rating plate.

Check the rating plate to verify that the heater is appropriate for the installation site.

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

Installation Codes

•These units must be installed in accordance with local building codes. In the absence of local codes, in the United

States, the unit must be installed in accordance with the National Fuel Gas Code, ANSI Z223.1 /NFPA 54. A

Canadian installation must be in accordance with the CSA B149 Natural Gas and Propane Installation Code. This

code is available from CSA Information Services, 1-800-463-6727. Local authorities having jurisdiction should be

consulted before installation is made to verify local codes and installation procedure requirements.

•Installations in aircraft hangars should be in accordance with ANSI/NFPA No. 409 (latest edition), Standard for

Aircraft Hangars. Installations in public garages should be in accordance with ANSI/NFPA No. 88A (latest edition),

Standard for Parking Structures. Installations in repair garages should be in accordance with ANSI/NFPA No. 88B

(latest edition), Standard for Repair Garages. In Canada, installations in aircraft hangars should be in accordance

with the requirements of the enforcing authorities, and in public garages, in accordance with the CSA B149 code.

•If the heater is being installed in the Commonwealth of Massachusetts, installation must be performed by a licensed

plumber or licensed gas fitter.

Heater Location

⚠ CAUTION ⚠

• Heaters should not be used in an application where the heated space temperature is below 40°F

(4°C). Operating under low ambient conditions may cause condensation to form in the heat

exchanger.

• Do not locate the heater where it may be exposed to water spray, rain, or dripping water.

Mounting Height Requirements

⚠ WARNING ⚠

If touched, the vent pipe and internal heater surfaces that are accessible from outside the heater

will cause burns. Suspend the heater a minimum of 12 feet (3.7 meters) above the floor.

NOTE: Suspended heaters are most effective when located as close to the working zone as

possible, and this fact should be kept in mind when determining the mounting heights to be used.

Hazards of Chlorine

NOTE: Remember, chlorine is heavier than air. This fact should be kept in mind when determining

the installation location of heaters and building exhaust systems.

The presence of chlorine vapors in the combustion air of heating equipment presents a potential corrosion hazard.

Chlorine, found usually in the form of Freon or degreaser vapors, when exposed to flame will precipitate from the

compound and form a solution with any condensation present in the heat exchanger or associated parts. The result

is hydrochloric acid, which readily attacks all metals, including 300 grade stainless steel. Care should be taken to

separate these vapors from the combustion process. This may be done by wise location of the unit with regard to

exhausters or prevailing wind directions.

Table 3. Minimum and Recommended Mounting Heights

Suspension

Bracket

Configuration

Height

Unit Size

060, 080 100, 125 150, 170 200

Feet (Meters)

Standard Minimum 12 (3.7) 14 (4.3) 16 (4.9) 18 (5.5)

Recommended 14 (4.3) 16 (4.9) 18 (5.5) 20 (6.1)

Angled Minimum 10 (3.0) 12 (3.7) 14 (4.3) 16 (4.9)

Recommended 11 (3.4) 13 (4.0) 15 (4.6) 17 (5.2)

6VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

GENERAL INFORMATION—CONTINUED

Dimensions

Refer to the SYSTEM CONFIGURATIONS section for tube assembly dimensions of specific systems. Burner cabinet

dimensions are shown in Figure 1.

Figure 1. Dimensions

Clearances

⚠ DANGER ⚠

• All listed minimum clearances to combustible materials MUST be adhered to at all times. Adequate

clearance MUST be provided around air openings into the combustion chamber, and there MUST

be suitable clearance for accessibility and for combustion/ventilation air.

• Minimum clearance from the heater must be maintained from vehicles parked below heater. In all

situations, clearances to combustibles must be maintained. Signs should be posted in storage

areas to specify maximum stacking height to maintain required clearance to combustibles.

Such signs must either be posted adjacent to the heater thermostats or—in the absence of such

thermostats—in a conspicuous location.

⚠ CAUTION ⚠

Building materials with low heat tolerance (plastics, vinyl siding, canvas, tri-ply, etc.) may be subject

to degradation at lower temperatures. It is the installer’s responsibility to ensure that adjacent

materials are protected from degradation.

Clearance to combustibles is defined as the minimum distance from the heater to a surface or object for which it is

necessary to ensure that a surface temperature of 90°F (50°C) above the surrounding ambient temperature is not

exceeded. Units must be installed so that clearances are in accordance with Table 4.

15-1/2

(394)

11-1/4

(286)

16-1/

(413)

11-1/4

(286)

VCS

VCT

VPT

VPS

NOTE: Dimensions are in inches (mm).

Table 4. Clearances

Unit

Size

Dimension (See Figure 2)

A B C D E F G H J K L

Inches (mm)

060, 080

74 (188)

29 (74) 72 (183) @ 15°

68 (173) @ 25°

61 (155) @ 35°

53 (135) @ 45°

43 (110) @ 55° 20 (51)

10 (26)*

8 (21)

22 (56) 12 (31)

41 (105) 8 (21) 12 (31)

100 32 (82) 16 (41)

125 39 (99) 47 (120) 20 (51) 18 (46)

150 48 (122)

170, 200 86 (219) 48 (122)

82 (209) @ 15°

78 (199) @ 25°

71 (181) @ 35°

61 (155) @ 45°

50 (127) @ 55°

11 (28) 48 (122) 20 (51)

*With end caps installed.

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

Figure 2. Clearances (Refer to Table 4)

END VIEW END VIEW (ANGLED INSTALLATION)

SIDE VIEW

OUTLET END VIEW (L-TUBE HEATER) RETURN END VIEW (U-TUBE HEATER)

BELOW

HEATER

SIDE

VENTED

0–55°

ABOVE

BURNER

SERVICE

DISTANCE

ABOVE

REFLECTOR

ABOVE

OUTLET

UNVENTED

END

UNVENTED

SIDE

UNVENTED

ABOVE

BURNER

SERVICE

DISTANCE

8VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

GENERAL INFORMATION—CONTINUED

Weights

To determine the actual weight of the system, add the collective weight of each component (refer to Table 5).

Table 5. Weights

Component Description

Model

VCT VCS VPT VPS

Pounds (kg)

Burner cabinet 38 (17.2) 34 (15.3) 29 (13.3) 25 (11.5)

Emitter tube with reflector 5-foot 7 (3.2)

10-foot 13 (5.9)

Tube section L-tube 10 (4.5)

U-tube 13 (5.9)

Brackets and couplers @3–10 (@2–5)

SYSTEM CONFIGURATIONS

Refer to the following tables and figures for system configuration and assembly details.

NOTE: Bends must be fitted at a distance of at least 50% of the total heat exchanger length—e.g.,

for a 60-foot long heater, 30 feet is the closest to the burner a bend can be.

Table 6. Model, Unit Size, and Tube Arrangement Application

Model

Unit Size

060 080 100 125 150 170, 200

Possible Tube Arrangements (See Figure 3)

VCS, VPS S20, S30, S40,

U20, U40

S30, S40,

U20, U40

S30, S40,

S50, U40

S30, S40, S50,

S60, U40, U60

S40, S50, S60,

S70, U40, U60

S50, S60, S70,

S80, U60, U80

VCT, VPT S30, S40,

U40

S30, S40,

U40

S30, S40,

S50, U40

S40, S50, S60,

U40, U60

S50, S60,

S70, U60

Table 7. Turbulator and Burner Insert Application

Tube Arrangement

(See Figure 3)Unit Size Turbulator Burner Insert*

Quantity

S20 060 3

S30

060 —

080 3

100 3 (natural gas units only)

4 (propane units only)

125 5

S40

060, 080, 100 —

125 4

150 —

S50

100, 125 — 1

170 2 (propane units only) —

200 4 (natural gas units only)

S60 125 —

1U20 060 1

080 3

U40 060, 080, 100, 125 —

150 4 —

U60 125 — 1

*On natural gas units only.

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

Figure 3. Tube Arrangements

S20

S30

S40

S50

S60

S70

U20

U40

U60

S80

U80

10 VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

Table 8. Tube Kits

Model Unit

Size

Gas

Type

System Length (Feet)

20 30 40 50 60 70 80

Tube Kit Code (Quantity)*

VCS**

060

Natural VC BS VC BS VC AS (2)

—

VCUS — —

Propane VC BS VC AS (2) VC AS (2)

VCUS VCUS —

080

Natural

VC BS VC AS (2) VC AS (2)

VCUS VCUS HDT5

HDT5 HDT5 —

Propane VC BS VC AS (2) VC AS (2)

VCUS VCUS —

100

Natural —

VC AS (2) VC AS (2) VC AS

—

VCUS HDT5 VC BS

HDT5 — HDT5

Propane —

VC AS (2) VC AS VC AS

VCUS VC BS VC BS

HDT5 VCUS HDT5

— HDT5 —

125 Natural, propane — VC AS (2) VC AS (2) VC AS VC BS (2) —

VCUS — VC BS —

150 Natural, propane —

VC AS VC AS VC BS (2) VC AS (2)

—VC BS VC BS — VC BS

VCUS —

170

Natural —

VC BS (2) VC BS (2) VC AS (2) VC AS

VCUS — VC BS VC BS (2)

VCUS —

Propane —

VC BS (2) VC AS (2) VC AS (2) VC AS

VCUS VC BS VC BS VC BS (2)

— VCUS —

200 Natural —

VC BS (2) VC BS (2) VC AS VC AS

VCUS VC BS VC BS (2) VC BS (2)

— VCUS VCUS —

VCT***

060

Natural

VC BS VC BS VC AS (2)

—

VPU HDT5 HDT5

HDT5 —

Propane VC BS VC BS VC AS (2)

VPU —

080 Natural, propane —

VC AS (2) VC AS (2)

VPU HDT5

HDT5 —

100

Natural —

VC AS (2) VC AS (2)

VPU HDT5

HDT5 —

Propane — VC AS (2) VC AS (2)

VPU —

*Quantity is one (1) inless otherwise indicated. Systems are shipped disassembled and are comprised of a burner cabinet and tube kits.

**Codes for U-tubes, L-tubes, and 5-foot straight tubes are as follows: U-tube = VCUS, L-tube = VCLS, and 5-foot straight tube = VCHS.

†Codes for U-tubes, L-tubes, and 5-foot straight tubes are as follows: U-tube = VPU, L-tube = VPL, and 5-foot straight tube = VPH.

NOTE: When the system has a U- or L-tube, refer to Table 7 to determine if a turbulator and/or burner insert is required.

SYSTEM CONFIGURATIONS—CONTINUED

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

Table 8. Tube Kits

Model Unit

Size

Gas

Type

System Length (Feet)

20 30 40 50 60 70 80

Tube Kit Code (Quantity)*

VCT***

125 Natural, propane —

VC AS (2) VC AS VC AS

—VPU VC BS VC BS

— VPU —

150 Natural, propane —

VC AS VC BS (2) VC BS (2)

—VC BS VPU —

VPU —

170

Natural — VC BS (2) VC BS (2) VC AS (2)

—

VPU — VC BS

Propane —

VC BS (2) VC AS (2) VC AS (2)

VPU VC BS VC BS

— VPU —

200 Natural —

VC BS (2) VC AS (2) VC AS (2)

VPU VC BS VC BS (2)

— VPU VPU

VPS***

060 Natural, propane VP B VP B VP A

—

VPU — VP D

080

Natural

VP B VP A VP A

VPU VP D VP D

HDT5 VPU HDT5

— HDT5 —

Propane

VP B VP A VP A

VPU VP D VP D

— VPU —

100 Natural, propane —

VP A VP A VP A

—

VP D VP D VP E

VPU HDT5 HDT5

HDT5 —

125 Natural, propane —

VP A VP A VP B

—VP D VP E VP E

—

150 Natural, propane —

VP A VP A VP B VP B

—VP E VP E VP E VP D (2)

VPU —

170 Natural, propane —

VP C VP C VP C VP C

VP E VP E VP D (2) VP D

VPU — VP E

200 Natural —

VP C VP C VP C VP C

VP E VP E VP D (2) VP D

VPU — VP E

*Quantity is one (1) inless otherwise indicated. Systems are shipped disassembled and are comprised of a burner cabinet and tube kits.

†Codes for U-tubes, L-tubes, and 5-foot straight tubes are as follows: U-tube = VPU, L-tube = VPL, and 5-foot straight tube = VPH.

NOTE: When the system has a U- or L-tube, refer to Table 7 to determine if a turbulator and/or burner insert is required.

—Continued

12 VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

SYSTEM CONFIGURATIONS—CONTINUED

Table 8. Tube Kits

Model Unit

Size

Gas

Type

System Length (Feet)

20 30 40 50 60 70 80

Tube Kit Code (Quantity)*

VPT***

060

Natural

VP B VP B VP A

—

VPU HDT5 VP D

HDT5 — HDT5

Propane VC BS VP B VP A

VPU — VP D

080 Natural, propane —

VP A VP A

VP D VP D

VPU HDT5

HDT5 —

100 Natural, propane —

VP B VP A

HDT5 VP D

— HDT5

125 Natural, propane —

VP A VP A VP A

—VP D VP D VP E

VPU —

150 Natural, propane —

VP A VP A VP B

—VP D VP E VP E

VPU —

170 Natural, propane —

VP C VP C VP C

—VP D VP E VP D (2)

VPU —

200 Natural —

VP C VP C VP C

—VP D VP E VP D (2)

VPU —

*Quantity is one (1) inless otherwise indicated. Systems are shipped disassembled and are comprised of a burner cabinet and tube kits.

†Codes for U-tubes, L-tubes, and 5-foot straight tubes are as follows: U-tube = VPU, L-tube = VPL, and 5-foot straight tube = VPH.

NOTE: When the system has a U- or L-tube, refer to Table 7 to determine if a turbulator and/or burner insert is required.

—Continued

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

Figure 4. Assembly Overview—S20 and S30

PALREVO ROTCELFER "9-"6

COUPLER

BURNER

END CAP

(OPTIONAL)

TWO FO LACIPYT SROTCELFER "3 '01

END CAP

(OPTIONAL)

BURNER INSERT

NEEWTEB ECNATSID

SUSPENSION POINTS

NOT TO EXCEED 12'

H (S20)TGNEL DELBMESSA LLAREVO LANIMON "½6'12

REFLECTOR BRACKET

NON-SLIP OVERLAP

SUSPENSION BRACKET SUSPENSION BRACKET

TEKCARB NOISNEPSUS

PLUS TUBE STRAP

REFLECTOR BRACKET

SLIP OVERLAP

TURBULATOR(S)

6" REFLECTOR OVERLAP 6" REFLECTOR OVERLAP

BURNER

H (S30)TGNEL DELBMESSA LLAREVO LANIMON "½6'13

THREE FO LACIPYT SROTCELFER "3 '01

BURNER INSERT

SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET

END CAP

(OPTIONAL)

NEEWTEB ECNATSID

SUSPENSION POINTS

NOT TO EXCEED 12'

END CAP

(OPTIONAL)

TEKCARB NOISNEPSUS

PLUS TUBE STRAP

COUPLER TURBULATOR(S)

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

COUPLER

REFLECTOR BRACKET

NON-SLIP OVERLAP

14 VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

SYSTEM CONFIGURATIONS—CONTINUED

Figure 5. Assembly Overview—S40 and S50

BURNER

H (S40)TGNEL DELBMESSA LLAREVO LANIMON "½6'14

'21 DEECXE OT OTN STNIOP NOISNEPSUS NEEWTEB ECNATSID

10'3" REFLECTORS

TYPICAL OF FOUR

6" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

6" REFLECTOR

OVERLAP

BURNER INSERT

END CAP

(OPTIONAL)

TEKCARB NOISNEPSUS

PLUS TUBE STRAP

TURBULATOR(S)

COUPLER

COUPLERCOUPLER

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET

SUSPENSION BRACKET

END CAP

(OPTIONAL)

BURNER

H (S50)TGNEL DELBMESSA LLAREVO LANIMON "½6'15

10'3" REFLECTORS

TYPICAL OF FIVE

BURNER INSERT

6" REFLECTOR

OVERLAP

6" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

END CAP

(OPTIONAL)

TEKCARB NOISNEPSUS

PLUS TUBE STRAP

TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS

TEKCARB NOISNEPSUS

COUPLER COUPLER COUPLER COUPLER

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

'21 DEECXE OT OTN STNIOP NOISNEPSUS NEEWTEB ECNATSID

END CAP

(OPTIONAL)

TURBULATOR(S)

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

Figure 6. Assembly Overview—S60 and S70

BURNER

H (S60)TGNEL DELBMESSA LLAREVO LANIMON "½6'16

10'3" REFLECTORS

TYPICAL OF SIX

6" REFLECTOR

OVERLAP

END CAP

(OPTIONAL)

TEKCARB NOISNEPSUS

PLUS TUBE STRAP

TEKCARB NOISNEPSUS

END CAP

(OPTIONAL)

TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS

6" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

'21 DEECXE OT OTN STNIOP NOISNEPSUS NEEWTEB ECNATSID

COUPLER COUPLER COUPLER COUPLER COUPLER

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

BURNER INSERT

BURNER

COUPLER COUPLER COUPLER COUPLER COUPLER COUPLER

71'6-1/2" NOMINAL OVERALL ASSEMBLED LENGTH (S70)

10'3" REFLECTORS

TYPICAL OF SEVEN

DISTANCE BETWEEN SUSPENSION POINTS NOT TO EXCEED 12'

SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET

SUSPENSION BRACKET

PLUS TUBE STRAP 6" REFLECTOR

OVERLAP

6" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

END CAP

(OPTIONAL)

END CAP

(OPTIONAL)

16 VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

SYSTEM CONFIGURATIONS—CONTINUED

Figure 7. Assembly Overview—S80

BURNER

H (S80)TGNEL DELBMESSA LLAREVO LANIMON "½6'18

10'3" REFLECTORS

TYPICAL OF EIGHT

REFLECTOR BRACKET

NON-SLIP OVERLAP

END CAP

(OPTIONAL)

SUSPENSION BRACKET

PLUS TUBE STRAP

'21 DEECXE OT OTN STNIOP NOISNEPSUS NEEWTEB ECNATSID

6" REFLECTOR

OVERLAP

6" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

3" REFLECTOR

OVERLAP

SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET

COUPLER COUPLER COUPLER COUPLER COUPLER COUPLER COUPLER

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

END CAP

(OPTIONAL)

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

Figure 8. Assembly Overview—U20 and U40

COUPLERS

BURNER

10'3" REFLECTORS TYPICAL OF TWO

DISTANCE BETWEEN

SUSPENSION POINTS

NOT TO EXCEED 12'

H (U20)TGNEL DELBMESSA LLAREVO LANIMON "½1'21

BURNER INSERT

3'3"

TEKCARB NOISNEPSUS

END CAP

(OPTIONAL)

SUSPENSION BRACKETSUSPENSION BRACKET

PLUS TUBE STRAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

TEKCARB NOISNEPSUS

R BRACKETOTCELFER

PALREVO

PILS-NON

TURBULATOR(S)

6"-9" REFLECTOR OVERLAPS

10'3" REFLECTORS TYPICAL OF FOUR

H (U40)TGNEL DELBMESSA LLAREVO LANIMON "½1'22

3'3"

SUSPENSION BRACKET

PLUS TUBE STRAP

TEKCARB NOISNEPSUS

END CAP

(OPTIONAL)

DISTANCE BETWEEN

SUSPENSION POINTS

NOT TO EXCEED 12'

TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS

COUPLERS

R BRACKETOTCELFER

PALREVO PILS-NON

R BRACKETOTCELFER

PALREVO

PILS

REFLECTOR BRACKET

SLIP OVERLAP

SUSPENSION BRACKET

REFLECTOR BRACKET

NON-SLIP OVERLAP

COUPLERS

BURNER INSERT

TURBULATOR(S)

BURNER

SUSPENSION BRACKET

18 VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

SYSTEM CONFIGURATIONS—CONTINUED

Figure 9. Assembly Overview—U60 and U80

6–9" REFLECTOR OVERLAP

10'3" REFLECTORS TYPICAL OF SIX

DISTANCE BETWEEN SUSPENSION POINTS NOT TO EXCEED 12'

H (U60)TGNEL DELBMESSA LLAREVO LANIMON "½1'23

3'3"

6" REFLECTOR OVERLAP

TEKCARB NOISNEPSUS

END CAP

(OPTIONAL)

BURNER

SUSPENSION BRACKET

PLUS TUBE STRAP

TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS

SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

R BRACKETOTCELFER

PALREVO PILS-NON

REFLECTOR BRACKET

SLIP OVERLAP

R BRACKETOTCELFER

SLIP OVERLAP

BURNER INSERT

R BRACKETOTCELFER

PALREVO PILS-NON

COUPLERS COUPLERS

COUPLERS

10'3" REFLECTORS TYPICAL OF EIGHT

H (U80)TGNEL DELBMESSA LLAREVO LANIMON "½1'24

3'3"

6" REFLECTOR OVERLAP 3" REFLECTOR OVERLAP6–9" REFLECTOR OVERLAP

SUSPENSION BRACKET

END CAP

(OPTIONAL)

BURNER

SUSPENSION BRACKET

TEKCARB NOISNEPSUS

NOISNEPSUS NEEWTEB ECNATSID

POINTS NOT TO EXCEED 12'

SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET SUSPENSION BRACKET

SUSPENSION BRACKET

PLUS TUBE STRAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

NON-SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

PALREVO PILS-NON

TEKCARB NOISNEPSUS TEKCARB NOISNEPSUS

REFLECTOR BRACKET

PALREVO PILS-NON

REFLECTOR BRACKET

SLIP OVERLAP

REFLECTOR BRACKET

SLIP OVERLAP

COUPLERS COUPLERS COUPLERS

REFLECTOR BRACKET

SLIP OVERLAP

COUPLERS

VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

INSTALLATION

Unpacking and Inspection

If, upon removing any heater component from its crate, the component has been found to have incurred any damage

in shipment, document the damage with the transporting agency and contact an authorized Factory Distributor. If

you are an authorized Distributor, follow the FOB freight policy procedures.

Pre-Installation Checklist

Check the rating plate for the gas specifications and electrical characteristics of the heater to ensure that they

are compatible with the gas and electric supplies at the installation site.

Read this manual and become familiar with the installation requirements of your particular heater.

If you do not have knowledge of local requirements, check with the local gas company or any other local agencies

who might have requirements concerning this installation.

Before beginning, make preparations for necessary supplies, tools, and manpower.

Check to see if there are any field-installed options (refer to Table 9) that need to be assembled/installed prior

to unit installation. Ensure that all options ordered are at the installation site.

Table 9. Field-Installed Options

Option Description

CE1 1/2-inch manual shutoff valve

CE2 3/4-inch manual shutoff valve

CE4 36-inch stainless steel flexible gas connector

CK11, CK31 Hanger kit (chain and S-hooks)

CK12–CK40 Turnbuckle kit to facilitate leveling system

CL1 Single-stage thermostat

CL22 Two-stage thermostat

DE1 Combustion air inlet adapter kit for model VPS unit size 200

DE2 Combustion air inlet adapter kit for models VCS, VCT, and VPT

DE5 Wind and rain hood kit for models VCS and VCT

DJ20 High-elevation conversion kit for installations at elevations >2000 feet

Heater Assembly

⚠ WARNING ⚠

Safety boots and protective gloves and eyewear are recommended.

Refer to the SYSTEM CONFIGURATIONS section for assembly details of specific systems.

NOTE: For aesthetic reasons, it is advisable to position all emitter tube seams facing down and

to install coupling fasteners so that they cannot be seen from beneath the heater.

1. Position emitter tubes on saw horses and mark position of bracket centers.

2. Install turbulator strip(s):

a. Interlock turbulator strip sections as shown in Figure 10, DETAIL A and slide connected sections into emitter

tube(s). Add further strips to form required length.

b. Where heater configuration requires more than three turbulator strips and exhaust heat exchanger tube is

adjacent to L- or U-tube, install turbulator strips as shown in Figure 10, DETAIL B.

c. Install turbulator strip into open end of last emitter tube only after it has been suspended and connected to

previous emitter tube.

20 VCS-VCT-VPS-VPT-IOM (06-23) 1042552-A

DETAIL A

DETAIL B

THREE TURBULATOR

STRIPS

TURBULATOR STRIP

VENT

INSTALLATION—CONTINUED

Heater Assembly—Continued

Figure 10. Turbulator Strip Installation

3. Install burner insert(s) as required into first emitter tube from where it is joined to second emitter tube as shown

in Figure 11.

Figure 11. Burner Insert Installation

4. Install couplers to join emitter tubes and L- or U-tubes (see Figure 12):

a. Slide coupler over tube joint.

b. Moving between coupler pins or bolts, apply equal pressure to tighten each in turn. DO NOT OVERTIGHTEN.

c. Complete assembly by installing self-tapping retention zip screws.

Figure 12. Typical Coupler

Page is loading ...

Reznor VPT, VCS, VCT, VPS Installation guide