:
Unlock symbol + or Next key Esc or Back key
- or Previous key
Display or Enter
key
Unlock or Modify
key
Status icons
Cabinet Temp
Instructions for the installation, use and care of:
G Series Reach-In & Pass-ru
Compact Undercounter
Compact Prep-Table
Quality Refrigeration
Quick Start Guide
1. RECEIPT & SUPPORT INSTALLATION:
You should carefully inspect your Traulsen unit for damage during delivery. If damage is detected, you should save all the crating
materials and make note on the carrier’s Bill Of Lading describing this. A freight claim should be led within 5 days.
Aer uncrating the unit, select a level location for nal placement. Install the casters (or optional leg supports) as shown below.
Supports: “Stem” type casters (standard). “Stem” type legs (optional).
Some models may use R-290 (Propane) as a refrigerant. If ammable refrigerant is present, follow instructions
as labeled on the unit. Proper care must be taken to avoid any damage to refrigeration system including refrigerant tubing, con-
denser, evaporator coils during handling, moving, installation and cleaning as it may cause risk of re or explosion. If damaged,
unit must be moved to well ventilated area away from any sources of ignition.
Further service and repair must be performed by qualied refrigeration technicians familiar with applicable safety standards
for ammable refrigerants. Technicians must use appropriate personal protective equipment and follow applicable safety pre-
cautions to avoid risk of re or explosion.
All models (except compact undercounter) should be installed to allow at least 12” of clear space above the unit. In all cases the
louvers must be free of any obstruction which could prevent proper air-ow.
Most units are supplied with a cord and plug, which can simply be plugged into a dedicated appropriately sized outlet. For those
requiring hard-wiring directly to the power supply, this should be done by a qualied electrician only.
2. CONTROL OVERVIEW:
Most Traulsen equipment is plug and play, such as G Series and most Compacts. However, once power is supplied to the unit, you
may make minor adjustments to your Traulsen unit.
2A- CONTROLLER DISPLAY
TR36058 P/N 375-60352-00 (09-15-17)
2B - UNDERSTANDING THE DISPLAY:
DISPLAY
SYMBOL
SYMBOL
DESCRIPTION
Temperature Reading/Settings
KeypaD Unlocked
Keypad Locked
Compressor On
Fan On
Defrost
Alarm/Door Open
DISPLAY
SYMBOL
SYMBOL
DESCRIPTION
Unlock/Modify Key
Minus (-)/Previous Key
Plus (+)/Next Key
Enter/Display Key
Esc/Back/Cancel Key
2C - UNLOCKING THE KEYPAD:
DISPLAY
SYMBOL
SYMBOL
DESCRIPTION
Unlock/Modify Key
Keypad Unlocked
2D - CHANGE THE TEMPERATURE SETPOINT:
DISPLAY
SYMBOL
SYMBOL
DESCRIPTION
Plus (+)/Next Key
Minus (-)/Previous Key
Enter/Display Key
Esc/Back/Cancel Key
2E - INITIATE A DEFROST OPERATION:
UNIT DEFROST INTERVAL
Upright Ref 8
Upright Frz 4
Compacts 6
DISPLAY
SYMBOL
SYMBOL
DESCRIPTION
Minus (-)/Previous Key
Esc/Back/Cancel Key
Defrost
-2-
On the Le Side of the display, there are colored LEDs for showing the temperature, status of
the compressor, fans, lock/unlock status, etc.
On the Right Side of the display, there are 5 capacitive touch buttons for managing the op-
eration of the unit.
Normally, the keypad is locked to prevent inadvertent changes to settings. e Unlock
Key is a white dot on the right side of the display, centered between the other 4 keys. Press
the Unlock key twice within a second in order to unlock the keypad (think “tap-tap”). e
Keypad Unlocked LED will turn on to indicate the keypad is now live. e keypad will stay
unlocked until there is 3 minutes of inactivity, at which time it will automatically lock the
keypad. ere are 2 operations the user can perform without having to enter a password:
• Change the temperature setpoint • Initiate a defrost operation
e setpoint to the unit can be changed simply by pressing the Plus or Minus Key. eir
will be a slight delay at rst to prevent an accidental change, so it will be necessary to hold
the key for 3-4 seconds until the value starts to ash. e ashing value indicates the setting
is being modied. To raise the setpoint, press the Plus Key to increment to the setpoint you
want. Similarly, press the Minus Key to lower the setpoint. When the desired value is reached,
press the Enter/Display Key to lock in the value. Pressing the Esc Key will abort the process
and keep the original setpoint. e keypad must be unlocked in order to change the setpoint
using the shortcut method.
Defrost is a necessary operation to remove frost that builds up on the evaporator coil and
reduces air ow within the cabinet. Normally this is done automatically based on a time
interval and the ambient conditions of the environment. A special sensor is used to measure
the humidity in the air to adjust the defrost interval depending upon humidity levels. e
nominal defrost intervals are shown in table.
To manually defrost the unit, press the Minus Key and the Esc Key simultaneously and hold
for 5 seconds. Units equipped with an LED temperature display will indicate when a defrost
cycle is in process. e Defrost Symbol will illuminate letting you know defrost is in eect.
Depending on the settings, the unit may also show “DEF”.
-3-
3 - HOT FOODS CABINETS - UNLOCKING THE KEYPAD:
DISPLAY
SYMBOL
SYMBOL
DESCRIPTION
Unlock/Modify Key
Keypad Unlocked
3A - HOT FOODS CABINETS - CHANGE THE TEMPERATURE SETPOINT:
DISPLAY
SYMBOL
SYMBOL
DESCRIPTION
Plus (+)/Next Key
Minus (-)/Previous Key
Enter/Display Key
Esc/Back/Cancel Key
3B - HOT FOODS CABINETS - TURN THE HEATERS OFF:
DISPLAY
SYMBOL
SYMBOL
DESCRIPTION
Keypad Unlocked
Unlock/Modify Key
4 - GENERAL CARE:
Disconnect electrical power supply before cleaning any parts of the unit.
All Traulsen equipment should be cleaned only with warm water, mild soap and a so cloth. Apply with a dampened cloth and wipe in
the direction of the metal grain.
Avoid the use of strong detergents and gritty, abrasive cleaners as they may tend to mar and scratch the surface. Do not use cleansers
containing chlorine, this may promote metal corrosion.
Care should also be taken to avoid splashing the unit with water, containing chlorinated cleansers, when mopping the oor around the unit.
For stubborn odor spills, use baking soda and water (mixed to a 1 TBSP baking soda to 1 pint water ratio).
5 - ADJUSTING THE SHELVES:
Shelves Mounted On Pins
First select the desired location and remove the white plastic covers in the interior back and sides by rotating them counter-clockwise.
Install the pins in the desired location by rotating them clockwise. Make sure the pin is securely tightened down. Do not over tighten.
Slide the shelf into its new position, and replace the white plastic covers into the holes vacated by the shelf pins.
Shelves Mounted On Clips & Pilasters
Shelves and shelf clips are shipped with the unit. For each shelf, insert four (4) shelf clips into the pilaster slots at the same height. e
shelf clips have a small projection on top which holds the shelf in position and prevents it from slipping forward. Aer installing shelf
clips on pilasters, place shelves on clips.
6 - CLEANING THE CONDENSER:
Disconnect electrical power supply before cleaning any parts of the unit.
is is the single most important thing you can do to promote long, ecient equipment life. For All Upright Cabinets, remove the two
bottom screws securing the louver panel, then pivot this upwards allowing full access to the front facing condenser. Contact factory
technical assistance at 800-825-8220 for all Compact Undercounter and Compact Prep-Table.
Normally, the keypad is locked to prevent inadvertent changes to settings. e Unlock Key
is a white dot on the right side of the display, centered between the other 4 keys. Press the
Unlock Key twice within a second in order to unlock the keypad (think “tap-tap”). e
Keypad Unlocked LED will turn on to indicate the keypad is now live. e keypad will stay
unlocked until there is 3 minutes of inactivity, at which time it will automatically lock the
keypad. ere are 2 operations the user can perform without having to enter a password:
• Change the temperature setpoint • Initiate a defrost operation
e setpoint to the unit can be changed simply by pressing the Plus or Minus Key. e will
be a slight delay at rst to prevent an accidental change, so it will be necessary to hold the key
for 3-4 seconds until the value starts to ash. e ashing value indicates the setting is being
modied. To raise the setpoint, press the Plus Key to increment to the setpoint you want.
Similarly, press the Minus Key to lower the setpoint. When the desired value is reached,
press the Enter Key to lock in the value. Pressing the Esc Key will abort the process and keep
the original setpoint. e keypad must be unlocked in order to change the setpoint using the
shortcut method.
e keypad must be unlocked in order to de-activate the heaters. Press the Unlock key twice
within a second in order to unlock the keypad. e Keypad Unlocked LED will turn on to
indicate the keypad is active. To turn the unit o, press and hold the Unlock Key until the
display shows “oFF”. To turn the unit ON, press the Unlock Key until the display shows the
temperature.
G Series Reach-In & Pass ru - Screw Location
Vacuum or brush any dirt, lint or dust from the nned condenser coil, around the compressor and other cooling
system parts as indicated. If signicant dirt is clogging the condenser ns, use compressed air to blow this clear.
When nished reverse the louver removal process as instructed above.
8 - SERVICE/WARRANTY INFORMATION:
Please visit our website at www.traulsen.com for additional service, literature and parts information. From our home page click on
the SERVICE tab, and select one of the following: SERVICE FINDER
OWNER’S MANUALS
PARTS PRICING
SERVICE & PARTS MANUALS
WARRANTY REGISTRATION
PROBLEM
POSSIBLE SOLUTION
1. Condensing unit fails to start. a. Check if cord & plug has been disconnected.
2. Condensing unit operates for prolonged
periods or continuously.
a. Are door(s) or drawer(s) closing properly?
b. Dirty condenser or lter. Clean properly.
c. Evaporator coils iced. Needs to defrost.
3. Food Compartment is too warm. a. Check door(s) or drawer(s) and gasket(s) for proper seal.
b. Check if a large quantity of warm food was recently added or the door was kept open for a long period of
time.
c. Microprocessor control setting is too high, readjust.
4. Food Compartment is too cold. a. Check if a large quantity of very cold or frozen food has recently been added. Allow adequate time for the
cabinet to recover its normal operating temperature.
b. Adjust the microprocessor control to warmer setting, readjust.
5. Condensation on exterior surface. a. Check door(s) or drawer(s) alignment & gaskets for proper seal.
b. Condensation on the exterior surface of the unit is perfectly normal during periods of high humidity.
c. Check perimeter heat setting and increase setting if <100.
7 - TROUBLE SHOOTING:
HOURS OF OPERATION:
Monday thru Friday 7:30 am - 4:30 pm CST
Quality Refrigeration
© 2017 Traulsen - All Rights Reserved
Traulsen
4401 Blue Moud Road Fort Worth, TX 76106
Phone (800) 825-8220 Service Fax (817) 740-6757
www.traulsen.com
Some models may use R-290 (Propane) as a refrigerant. Service and repair must be performed by qualied re-
frigeration technicians familiar with applicable safety standards for ammable refrigerants. Technicians must use appropriate
personal protective equipment and follow applicable safely precautions to avoid risk of re or explosion. Service and repair
must be performed in well ventilated and unconned area, away from any ignition sources. All system components must be
replaced with like components. Factory recommends to use exact make and models to assure the consistent performance and
to minimize the risk of possible ignition due to incorrect parts. In case of uncertainty or parts unavailability, contact Traulsen
technical assistance at 800-825-8220.
Amp Plate
Before making contact at 800-825-8220, please make sure you have model and serial number of your
unit. Amp plate with information needed is located inside the unit.
/
