Bennett Marine ES2000 Installation guide

Bennett Marine
Brand
Bennett Marine
Model
ES2000
Type
Installation guide

This manual is also suitable for

ES2000 Rocker Control Installation for Hydraulic Systems
5005447 - R102219
• Before drilling any holes, read the entire instructions.
• Unsnap the bezel from the control. Using the bezel locate
the position for the control at the helm. Check carefully
to make sure there are no obstructions behind the
dashboard before drilling any holes.
• The bezel requires a footprint of 2-13/16" x 2-13/16". Cut a
2-1/2" hole in the center of the footprint using a hole saw.
• Pull the wire harness up through the hole and attach it to
the back of the control with the ring terminals enclosed.
Please make sure that the gasket is in place with the flat
side down before attaching wires to the control. There
are two screws for each wire. (The wire can be attached
to either screw.) The brass strip is marked with the first
letter of that color of the wire. All 12 screws must be in
place and snug for proper control function.
• Mark the four locations for the 7/64" pilot holes and drill.
Test fastening with the #8 screws. Open the holes to 1/8"
if necessary.
• Place the wire harness and switch in the hole with yellow
connections at top. Secure the switch plate assembly with
the enclosed #8 screws. Be sure the switch is properly
seated and snap bezel onto switch plate assembly.
• Note: The bezel will secure completely when BOW DOWN
is at the top and the switch plate assembly is mounted
with the top and bottom in proper position (yellow
connections at top).
Drilling Template
PN: ES2000
For more information on a complete hydraulic trim tab system,
please visit BennettTrimTabs.com/Hydraulic
Items Included
• Hydraulic Rocker Control
• (4) #8 screws
• (4) Ring terminals
Tools Required
• Power drill
• 7/64" Drill bit
• 2.5" Hole saw
Wiring Diagram
Have questions? We’re here to help.
Visit BennettTrimTabs.com or call (866)894-1626.
Installation Instructions
Yellow
Red
Blue
Green
7/64"
Actuators
& Tabs
HPU (Pump)
Rocker
Control
Snap-on
Bezel
Blue
Pump pressure
(Trim tabs down)
Yellow
Pump retract
(Trim tabs up)
Red
Port valve
Green
Starboard valve
Orange
Connect to 12V (+)
Must be printed or
copied at 100% scale
1"
When the port tab is lowered independently, an upward force
at the port stern of the boat is created. The inverse applies
when lowering the starboard tab independently.
When the tabs are deployed downward, the water force on
the trim tab surface creates upward pressure, raising the stern
and lowering the bow. The port trim tab lowers the starboard
bow, and the starboard trim tab lowers the port bow.
Properly sized trim tabs improve the
performance of your boat by adjusting the
running angle of your vessel. Bennett Marine
trim tabs help you get on plane faster, correct
listing, improve visibility, and increase your fuel
eciency and performance.
• Get up on plane quickly, and at lower speeds
• Increase performance and fuel eciency
• Increase visibility and safety
• Adjust the boat’s attitude for changes
in speed, sea conditions, and shifting weight
• Correct listing and porpoising
Lowers
Stbd. Bow
Raises
Stbd Bow
Raises
Port Bow
Lowers
Port
Bow
Operating the Rocker Control
Trim tabs are easy to use and after just a few times
using will become second nature. The concept is
simple but the results are impressive.
Making Small Adjustments
The key to getting the best results from your trim
tabs is to operate them in short half-second “bursts”
and let the boat react before making another
adjustment. The amount of time between corrections
is influenced by the size of the trim tabs and the
boat’s speed.
Learn More About Trim Tabs
Learn more about trim tabs at
BennettTrimTabs.com/Guide
• Key features & benefits
• Sizing guidelines
• System comparison
• Install tips, and more
Have questions? We’re here to help.
Visit BennettTrimTabs.com or call ( ) -1 .
Port
Ta b
Port
Bow
Stbd.
Ta b
Stbd.
Bow
Pitch
Correction
WITH Trim Tabs
Without Trim Tabs
Roll Correction
Port
Ta b
Stbd.
Ta b
How Trim Tabs Work
Using Your Rocker Helm Control
866 894 626
  • Page 1 1
  • Page 2 2

Bennett Marine ES2000 Installation guide

Bennett Marine
Brand
Bennett Marine
Model
ES2000
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents