Ambiano GT-EWM-03-UK User manual
- Category
- Ice cube makers
- Type
- User manual
This manual is also suitable for
User Manual
Manual
del usuario
English .... 02
Español ... 22
COUNTERTOP ICE MAKER
MÁQUINA DE HIELO
Druckbuch ES_Maschine USA.indb 1Druckbuch ES_Maschine USA.indb 1 04.11.2022 16:50:1604.11.2022 16:50:16
2
Scope of supply
Scope of supply
5
1
3
2
8
7
6
10
11
9
4
12
13
Druckbuch ES_Maschine USA.indb 2Druckbuch ES_Maschine USA.indb 2 04.11.2022 16:50:1604.11.2022 16:50:16
3
Device parts
Device parts
1Control panel
2Viewing window
3Ventilation slots
4Power cable with mains plug
5Lid
6Freezing unit
7Water tank with inserted ice cube basket
8Exhaust air blower
9Stopper
10 Ice scoop
11 Ice cube basket
12 Light barrier
13 Sieve for suction opening (water for ice cube preparation)
Additional scope of supply:
- Operating Instructions
- Warranty certificate
Druckbuch ES_Maschine USA.indb 3Druckbuch ES_Maschine USA.indb 3 04.11.2022 16:50:1604.11.2022 16:50:16
4
Table of Contents
Contents
Scope of supply ................................................................... 2
Device parts ......................................................................... 3
General ................................................................................5
Read and keep operating instructions ................................5
Explanation of symbols ...........................................................5
Safety ..................................................................................6
Intended use ........................................................................... 6
Safety instructions ....................................................................7
Instructions on hygiene and residual water .................. 10
Functional principle ..........................................................11
Initial use ............................................................................11
Unpacking and setting up the machine .............................11
Check scope of delivery .........................................................11
Clean thoroughly ....................................................................11
Control panel .....................................................................12
Produce ice cubes ..............................................................12
Miscellaneous ................................................................... 15
Refill water .............................................................................. 15
Drain water ............................................................................. 15
Cleaning ............................................................................. 16
Transportation and Storage ............................................ 18
Troubleshooting ................................................................ 19
Technical data ...................................................................20
Disposal ..............................................................................20
Disposing of the packaging ................................................. 20
Disposing of the appliance ................................................... 20
Druckbuch ES_Maschine USA.indb 4Druckbuch ES_Maschine USA.indb 4 04.11.2022 16:50:1604.11.2022 16:50:16
5
General
Read and keep operating instructions
These operating instructions belong to this countertop ice maker.
They contain important information regarding initial use and
handling. Before using the ice cube machine, read through the
operating instructions carefully, particularly the safety
instructions. Failure to comply with these operating instructions
may lead to serious injuries or damage to the ice cube machine.
Please also note the country-specific directives and laws abroad. Keep the
operating instructions for further use. If you pass the ice cube machine on to
third parties, please also ensure that you pass on these operating instructions.
Explanation of symbols
The following symbols and signal words are used in these operating
instructions, on the ice maker or on the packaging.
WARNING! This signal symbol/word indicates a hazard with
a medium degree of risk, which could lead to
death or serious injury if it is not avoided.
NOTE! This signal symbol/word warns of possible
material damage.
This symbol gives you useful additional information about assembly
or about operation.
Warning: Fire hazard/flammable materials
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed including the following:
1. Read all instructions.
2. Do not touch hot surfaces. Use handles or knobs.
3. To protect against electrical shock do not immerse cord, plugs, or (state
specific part or parts in question) in water or other liquid.
4. Close supervision is necessary when any appliance is used by or near
children.
General
Druckbuch ES_Maschine USA.indb 5Druckbuch ES_Maschine USA.indb 5 04.11.2022 16:50:1604.11.2022 16:50:16
6
5. Unplug from outlet when not in use and before cleaning. Allow time to cool
before putting on or taking off parts.
6. Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions or has been damaged in any manner. Return
appliance to the nearest authorized service facility for examination, repair, or
adjustment.
7. The use of accessory attachments not recommended by the appliance
manufacturer may cause injuries.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter, or touch hot surfaces.
10. Do not place on or near a hot gas or electric burner, or in a heated oven.
11. Extreme caution must be used when moving an appliance containing hot oil
or other hot liquids.
12. Always attach plug to appliance first, then plug cord into the wall outlet. To
disconnect, turn any control to “off”, then remove plug from wall outlet.
13. Do not use appliance for other than intended use.
14. Save these Instructions.
15. Household use only.
SAVE THESE INSTRUCTIONS
Safety
Intended use
This ice cube machine is for the production of ice cubes in conventional
household quantities. It is intended for private use and is not suitable for
commercial purposes. WARNING: Only fill with drinking water.
The ice cube machine is not suitable for connection to an external water
supply.
Only use the ice cube machine as described in these operating instructions.
Any other use is regarded as inappropriate and may lead to material damage
or even to personal injury. The ice cube machine is not a toy.
The manufacturer or retailer shall not assume any liability for losses caused by
intended or improper use.
Dispose of the device at the end of its useful life in accordance with the local
regulations, as it uses flammable propellants and coolants.
• WARNING: When setting up the appliance, make sure that the power cord is
not pinched or damaged.
• WARNING: Do not place portable multiple sockets or portable power
supplies on the back of the unit.
General
Druckbuch ES_Maschine USA.indb 6Druckbuch ES_Maschine USA.indb 6 04.11.2022 16:50:1604.11.2022 16:50:16
7
• WARNING: Keep the air openings in the device housing or the installation
structure free from obstacles.
• WARNING: To speed up the thawing process, do not use any mechanical
devices or other methods than those recommended by the manufacturer.
• WARNING: Do not use any electrical device to defrost your appliance.
• WARNING: Do not damage the coolant circuit. Exercise caution when
handling, transporting or operating the device.
• WARNING: Repairs may only be carried out by trained specialist personnel.
Only spare parts approved by the manufacturer may be used.
• WARNING: Do not use any electrical devices in the food compartments of
this device, unless they are recommended by the manufacturer.
• The insulation propellant used for this device is flammable. To avoid
possible hazards for the environment or for human health due to
uncontrolled disposal, you must dispose of this device properly by
ensuring the sustainable reuse of raw materials and the proper handling
of the flammable insulation propellant. You should only dispose of this
device by submitting it to a public collection centre. Please contact your
local authority or the nearest collection center for detailed instructions on
the correct disposal of this device.
• Do not store any flammable substances in the device, such as aerosol
sprays with flammable propellant.
Safety instructions
WARNING!
Electric shock hazard!
Faulty electrical installation, excessive mains voltage or incorrect
handling of an electric device may result in electric shock.
− The tank of the device is filled with water for ice cube
production. However, never immerse the device itself, the
power cable or plug in water or any other liquid, as there
is otherwise a risk of electric shock.
− Do not operate the device in a damp environment or in an
environment with high humidity.
− Only connect the device to a properly installed power
outlet, with voltage corresponding to the “Technical data”.
− Ensure that the power outlet is well-accessible, so that you
can disconnect the mains plug quickly, if necessary.
Safety
Druckbuch ES_Maschine USA.indb 7Druckbuch ES_Maschine USA.indb 7 04.11.2022 16:50:1604.11.2022 16:50:16
8
− Do not use the ice cube machine, if the device, power
cable or mains plug are damaged or if the device has
fallen.
− Ensure that the power cable cannot be damaged by sharp
edges or hot items.
− Never operate the ice cube machine with wet hands.
− Disconnect the power cable from the power outlet, if you
are not using the ice cube machine, before cleaning,
moving or packing the device away and if an obvious fault
occurs during operation, as well as in thunder storms.
Always pull on the mains plug, not on the power cable.
− Do not wrap the power cable around the machine.
− Do not use an extension cord.
− Do not make any modifications to the appliance or the
power cable. Only allow repairs to be carried out by a
professional workshop. Also pay attention to the enclosed
guarantee conditions.
− If the machine, power cable or plug are damaged, you
must have these repaired by the manufacturer or a
specialist workshop, in order to avoid hazards.
− Do not use the machine near bathtubs, swimming pools,
shower trays or other containers holding water. Electric
shock hazard!
− If the power cable of this device should be damaged,
it must be replaced by the manufacturer, its customer
service or a similarly qualified person, in order to avoid
hazards.
WARNING!
Hazards for children and persons with impaired physical,
sensory or mental capabilities (e.g. partially disabled,
elderly persons with impairment to their physical and
mental capabilities) or a lack of experience and knowledge
(for example, older children).
− This device may be used by children aged 8 and above
Safety
Druckbuch ES_Maschine USA.indb 8Druckbuch ES_Maschine USA.indb 8 04.11.2022 16:50:1604.11.2022 16:50:16
9
and by persons with impaired physical, sensory or mental
capabilities or a lack of experience and/or knowledge, if
they are supervised or instructed regarding safe use of the
device and have understood the resulting hazards.
− Children must not play with the machine. Cleaning and
user maintenance must not be carried out by children
without supervision.
− Keep children under the age of 3 away from the device,
unless they are constantly being supervised.
− Children aged 3 years and older and younger than 8years
are not allowed to insert the mains plug into the power
outlet, adjust the device, clean it and/or perform the
maintenance.
− Keep children away from packaging materials. Suffocation
hazard from swallowing packaging material and small
parts. Ensure that the packaging bag is not pulled over
the head.
− Do not wrap the power cable around the device or parts of
the device. If a cable winder is available, use it accordingly.
Incorrect winding can damage the cable insulation and
pose a risk of electric shock.
WARNING!
Injury hazard!
Improper handling of the machine may result in injuries.
− During ice production, the cooling elements inside the
machine become very cold. Do not touch these parts.
Otherwise, there is a risk of injury from freezer burn.
NOTE!
Risk of damage!
Improper handling of the machine may result in damage.
− WARNING: Only fill with drinking water.
− After transport and before initial use, set the device up
at a desired location and leave it switched off for at least
2hours first, so that the coolant can settle. Otherwise the
Safety
Druckbuch ES_Maschine USA.indb 9Druckbuch ES_Maschine USA.indb 9 04.11.2022 16:50:1604.11.2022 16:50:16
10
compressor could become damaged. Place the machine
on a level surface.
− Also leave the machine to stand for a few hours, if you
transport it from a cold to a warm room, before switching
the machine on.
− Do not turn the machine upside-down, otherwise the
compressor could become damaged.
− During ice production, the machine gives off heat and
needs a sufficient supply of fresh air. If the heat cannot be
discharged properly, there is a risk that the machine will
overheat and become damaged.
Therefore, please make sure ...
... that the device openings are not covered up and are
free and clean. Do not insert objects into the openings
under any circumstances.
... that a distance of at least 6 inches remains free around
the machine.
... that the machine is standing on a heat-resistant surface.
− Do not use the ice cube machine any longer, if it has fallen
down, if the plastic components of the ice cube machine
have cracks or flaws or have deformed. This also applies, if
the machine has become deformed or leaks.
Instructions on hygiene and residual
water
• Clean the surfaces on regular basis that come into contact with foods and
accessible drainage systems.
• The opening of the lid for a longer period of time can cause a significant
increase to the temperature inside the device. Therefore, always only open
the lid briefly.
• Even if the water tank is empty, a small residual amount of water remains in
the machine.
• The water must be drained 1x per day or if you no longer use the machine
for a longer period of time.
• To avoid contamination of foods, please note the following:
• Clean the water tanks, if they have not been used for 48 hours.
• If the refrigeration device remains empty for a longer period of time,
Instructions on hygiene and residual water
Druckbuch ES_Maschine USA.indb 10Druckbuch ES_Maschine USA.indb 10 04.11.2022 16:50:1604.11.2022 16:50:16
11
switch the device off, clean and dry it and leave the door open, in order
to avoid mold formation in the device.
Functional principle
The water container is filled with water for ice cube production. After the
machine is supplied with current and switched on, the freezing coils are put
into contact with the water. After a few minutes, the ice cubes are formed layer-
by-layer on the ice-cold freezing coils.
As soon as the ice cubes are finished on the freezing coils and are frozen “in
shape”, the coolant in the machine heats up the heating gas briefly in the
freezing coils, as a result of which, the ice cubes release and fall down. This
process is referred to as “melting off”.
A pusher pushes the finished ice cubes into the ice cube basket and the
production of the next ice cubes starts over again automatically.
Initial use
Unpacking and setting up the machine
• The ice cube machine is bulky. Let a second person help you
with unpacking and setup, if possible.
• Do not take hold of the device on the lid, but rather, on the
sides.
− Place the machine on a horizontal, level, vibration-free and heat-resistant
surface. The ambient temperature should be between 50 °F and 90 °F.
Remove all packaging materials.
Check scope of delivery
1. Check whether all parts are present.
2. Check whether the device or accessories show damage. If this is the case,
do not use the ice cube machine. Contact the manufacturer via the service
address stated on the guarantee card.
Clean thoroughly
− Prior to initial use, clean all parts of the machine and the accessories, as
described in the “Cleaning” section.
Wait for another 2 hours, before switching the machine on and
producing the first ice cubes. Do not insert the mains plug into a
power outlet yet, do not switch the machine on yet.
Functional principle
Druckbuch ES_Maschine USA.indb 11Druckbuch ES_Maschine USA.indb 11 04.11.2022 16:50:1604.11.2022 16:50:16
12
Control panel
All device functions are started via the control panel. The control panel is
comprised of two control buttons and six illuminated displays.
Operating buttons:
Name Meaning
ON/OFF Start-end ice production
SELECT Select ice cube size, select cleaning program
Displays:
Name Meaning
SMALL small ice cube size is set
LARGE large ice cube size is set
CLEAN Cleaning program is selected (see “Cleaning”)
POWER Device is supplied with power (flashes) and/or machine is
operating (lights up continuously)
ADD WATER Water tank is empty (see “Refill water”)
ICE FULL Ice collection container is full (see “Remove ice cubes”)
Produce ice cubes
NOTE!
Risk of damage!
Improper handling of the machine may result in damage.
− WARNING: Only fill with drinking water.
a) Fill with water
The colder the water is that you fill into the machine, the faster
and more energy-saving the ice cubes will be produced.
However, the water should not be colder than 46 °F and not
warmer than 68 °F.
Control panel
Druckbuch ES_Maschine USA.indb 12Druckbuch ES_Maschine USA.indb 12 04.11.2022 16:50:1604.11.2022 16:50:16
13
1. Open the lid of the device and remove the ice cube basket 11 .
A
2. Fill the ice cube machine
with water. Ensure that
you do not exceed the
maximum mark. The front
ice cube basket supports
in the water tank serve as
the MAX mark. Maximum
capacity of the machine:
approx. 60.8 fl.oz.
3. Reinsert the ice cube
basket and close the lid of
the device. The ice cube
basket can only be inserted
properly in one position.
b) Start production
• If ADD WATER lights up, the water in the water tank is used up
and the machine will stop the ice cube production (see “Refill
water”).
• You can switch the machine off at any time by pressing the
ON/OFF button.
1. Connect the mains plug to a power outlet. The POWER lamp lights up, as well
as SMALL or LARGE.
2. Choose the required ice cube size with the SELECT button.
• Larger ice cubes LARGE need more production time than small ones.
• The small ice cubes SMALL are very suitable for producing “crushed ice”.
3. Press the ON/OFF button to start the ice production.
The POWER button now lights up continuously and the machine starts with
the fully-automated production of ice cubes. Please note:
• The machine has a slight “after-run”, i.e., it always takes several seconds
before the machine responds to the button presses. That is normal and
is not a fault.
• Due to the fast freezing process, it can occur that the ice cubes look
slightly milky, because the air captured in the water ends up in the ice
cubes. However, this has no influence on the quality or flavor of the ice
cubes.
Produce ice cubes
Druckbuch ES_Maschine USA.indb 13Druckbuch ES_Maschine USA.indb 13 04.11.2022 16:50:1604.11.2022 16:50:16
14
• Leave the lid 5 closed during ice cube production. Only open it to
remove finished ice cubes.
• A production cycle takes between 7 and 10 minutes, depending on the
water temperature and ambient temperature, as well as the selected ice
cube size.
• Due to technical reasons, the ice cubes do not remain permanently fro-
zen in the ice cube basket.
c) Remove ice cubes
The ice cube machine produces approx. 9 ice cubes per cycle and then
transports them automatically into the ice cube basket 11 .
As soon as the basket is full, the ICE FULL display lights up red and the machine
stops.
The light barrier 12 detects the fill level of the ice cube basket, or ice cubes
that are lying in the way. You can then move these ice cubes into the ice cube
basket 10 with the ice scoop and the device will run one cycle further.
The ice cubes are kept chilled in the ice cube basket, whereby the condensation
automatically drips back into the water tank.
It is advisable to tip the ice cubes back into the water beneath the ice cube
basket when initially using the ice cube maker. This way, the interior space of
the machine will cool down more quickly and the ice cubes will then have the
desired size.
You can remove ice cubes at any time. As soon as sufficient ice cubes have been
removed or have melted, the production of ice cubes will start automatically
again.
BTo remove ice cubes:
1. Open the lid 5.
2. Remove the ice cube basket
and empty it or remove it or
remove individual ice cubes
with the ice scoop 10 .
Condensation may drip
out of the ice cubes. Shake
the basket slightly before
removing it completely.
3. Reinsert the ice cube basket
and close the lid.
Produce ice cubes
Druckbuch ES_Maschine USA.indb 14Druckbuch ES_Maschine USA.indb 14 04.11.2022 16:50:1704.11.2022 16:50:17
15
d) After use
If you do not want to produce any more ice cubes:
1. Switch the machine off by pressing the ON/OFF button. The POWER display
flashes.
2. Remove the mains plug from the power outlet.
3. Let the machine heat up to room temperature.
4. Clean the machine (see “Clean”).
Miscellaneous
Refill water
If the ADD WATER display lights up red, the water in the tank is used up and the
ice cube production is stopped automatically. The ice cubes that have been
produced until then will be kept chilled, but will slowly thaw away over time.
1. Press the ON/OFF button to switch the machine off. The POWER display
flashes.
2. Open the lid 5 and remove the ice cube basket 11 .
3. Fill up with the required quantity of water (however, no more than up to the
MAX mark).
4. Reinsert the ice cube basket and close the lid.
5. Press the ON/OFF button again to restart the ice cube production.
Drain water
NOTE!
Risk of damage!
Improper handling of the ice cube machine may lead to damage
to the machine.
− Do not turn the machine upside-down, as otherwise the
compressor could become damaged. Drain the water via
the opening on the bottom.
The water must be drained 1x per day or if you no longer use the machine for a
longer period of time.
Miscellaneous
Druckbuch ES_Maschine USA.indb 15Druckbuch ES_Maschine USA.indb 15 04.11.2022 16:50:1704.11.2022 16:50:17
16
• If there is still a larger quantity of water in the machine, first
scoop it out with a cup, or similar. Small quantities can also be
absorbed with a soft, absorbent cloth.
• If residual water is in the freezing unit, carefully push the
freezing unit back in by hand, so that all of the water flows
back into the water tank.
9
C
1. Place the front side of
machine on an edge
and place e.g. a bucket
underneath it.
You can also position the
machine over a sink.
2. Pull out the stopper
on the bottom of the
machine.
The water runs out.
As soon as no water runs
out anymore, reinsert the
stopper. Then, you can clean
the machine.
Cleaning
WARNING!
Electric shock hazard!
Incorrect handling of the machine can cause an electric shock.
− Remove the mains plug from the power outlet before
cleaning the machine.
− Do not immerse the machine or the power cable or the
mains plug in water or other liquids.
WARNING!
Injury hazard!
Miscellaneous
Druckbuch ES_Maschine USA.indb 16Druckbuch ES_Maschine USA.indb 16 04.11.2022 16:50:1704.11.2022 16:50:17
17
Improper handling of the machine may result in injuries.
− During ice production, the cooling elements inside the
machine become very cold. Do not touch these parts.
Otherwise, there is a risk of injury from freezer burn.
NOTE!
Risk of damage!
Improper handling of the ice cube machine may lead to damage
to the machine.
− Do not clean the machine with hard, scratching or
abrasive detergents, steel wool, or similar. The surface
could become scratched.
Make sure that all detergent is completely rinsed/wiped off
after use. If residues remain in the machine, this has a negative
impact on the flavor of the finished ice cubes.
1. Switch the machine off, remove the mains plug from the power outlet and
let the machine heat up to room temperature.
2. Check whether there is still a larger quantity of water in the machine. If so,
you should let the water drain out (see “Drain water”).
Clean ice cube basket and ice scoop
1. Remove the ice cube basket 11 from the machine.
2. Clean the ice cube basket and ice scoop 10 by hand with mild dishwashing
water.
3. Dry all parts off thoroughly.
Clean housing
− Wipe the housing clean from the outside with a damp cloth.
Clean the inside of the machine
1. If necessary, remove water from the inside (see “Drain water”).
2. Pull off the sieve 13 upwards to clean it.
Clean the sieve under running water with a brush or a cloth.
3. Reattach the cleaned sieve by pressing it onto both pins on the base.
4. Clean the inside of the machine with a soft cloth that is soaked with a mild
soap solution. Wipe the inside afterwards with clean water and then let it
dry completely.
5. Dry it off with a soft cloth, if necessary.
Cleaning
Druckbuch ES_Maschine USA.indb 17Druckbuch ES_Maschine USA.indb 17 04.11.2022 16:50:1704.11.2022 16:50:17
18
6. Check whether the stopper has been reinserted.
Use of the cleaning program
The machine has its own cleaning program. You should use this cleaning
program, if the ice no longer tastes fresh.
We recommend first running the cleaning program with a mild
detergent and then performing a second run with fresh water.
This will remove all cleaning residues. You can use a water-citric
acid mixture as a detergent. The ratio of citric acid to water
should be approximately 5 %.
1. Remove the ice cube basket 7 and fill the ice cube machine with 17 fl.oz of
cleaning fluid or water.
2. Close the lid 5 and insert the mains plug 4 into a power outlet.
The POWER button flashes.
3. Press SELECT repeatedly until the CLEAN display lights up in the control
panel.
4. Press ON/OFF to start the cleaning program.
The POWER lamp will now light up continuously. The cleaning program is
made up of several cycles with a total time of approx. 8 minutes.
5. Then, remove water from the inside (see “Drain water”).
Run the cleaning program again if the ice cubes no longer taste fresh.
Transportation and Storage
Transportation
NOTE!
Risk of damage!
Improper handling of the ice machine may lead to damage to
the machine.
− After transport, set the machine up at a desired location
and leave it switched off for at least 2 hours first, so that
the coolant can settle.
− Also leave the machine to stand for a few hours, if you
transport it from a cold to a warm room.
− Do not turn the machine upside-down, as otherwise the
compressor could become damaged.
Cleaning
Druckbuch ES_Maschine USA.indb 18Druckbuch ES_Maschine USA.indb 18 04.11.2022 16:50:1704.11.2022 16:50:17
19
• Use the original packaging for transportation, wherever possible. It is the
best way of protecting the machine.
• Let a second person help you carry the machine. Never take hold of the
machine on the lid.
• Transport the machine upright.
• After each transport, wait for approx. 2 hours before switching the machine
back on.
Storage
If you do not use the ice cube machine for a longer period of time:
• Clean the machine, see “Cleaning”.
• Leave the door open, in order to avoid mold formation on the inside.
• Keep the machine in a dry place that is inaccessible to children. You can
use the original packaging as outer packaging.
• Do not wrap the power cable around the device or parts of the device. If a
cable winder is available, use it accordingly. Incorrect winding can damage
the cable insulation and pose a risk of electric shock.
Troubleshooting
Problem Problem rectification
No function • Mains plug connected to the power
outlet?
A button/display lights up in the
control panel.
• See “Control buttons and operating
displays”.
Ice is sticking together. • Water temperature is too low. Use
the water with a temperature of
between 46 °F and 68 °F.
The machine is running, but no ice
is being produced.
• Water temperature is too high or too
low.
• Use the water with a temperature of
between 46 °F and 68 °F.
• Ambient temperature is too high.
Put the machine in a cool place.
• The machine is defective. Contact
our service centre.
Water leakage under the machine. • Stopper completely inserted?
Transportation and Storage
Druckbuch ES_Maschine USA.indb 19Druckbuch ES_Maschine USA.indb 19 04.11.2022 16:50:1704.11.2022 16:50:17
20
Technical data
Model: GT-EWM-03-US
Voltage: 120 V~, 60 Hz
Protection class: I
Rated Electric Current: 1.7 A
Ice cube basket capacity: approx. 17.6 oz
Tank capacity: approx. 60.8 fl.oz max.
Ice production: approx. 9 ice cubes per cycle (7-10 minutes)
Climate class: ST / SN / N / T
Coolant: R600a/approx. 0.052 lbs.
Dimensions: approx. 13.2 x 8.9 x 11.5 inch
Weight: approx. 16.5 lbs
Product number: 823190
Because our products are constantly being further developed and improved,
design modifications and technical changes are possible.
Disposal
Disposing of the packaging
Sort the packaging before you dispose of it. Dispose of paperboard and
cardboard with the recycled paper service and wrappers with appropriate
collection service.
Disposing of the appliance
Old appliances may not be disposed of in the household garbage!
Should the appliance no longer be capable of being used at some point in time,
dispose of it in accordance with the regulations of your state or country.
Please ensure your recycling information does apply to the local regulations
and the EPA recommendations (www.epa.gov).
Disposal
Druckbuch ES_Maschine USA.indb 20Druckbuch ES_Maschine USA.indb 20 04.11.2022 16:50:1704.11.2022 16:50:17
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
Ambiano GT-EWM-03-UK User manual
- Category
- Ice cube makers
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI